共查询到20条相似文献,搜索用时 62 毫秒
1.
土壤石油烃污染的植物毒性及植物-微生物联合降解 总被引:8,自引:2,他引:6
通过盆栽实验研究了土壤石油烃污染对玉米和水稻根伸长的影响,并在土壤中接种经过筛选得到的石油烃降解菌,研究石油烃降解菌对石油烃毒性的影响以及对土壤中石油烃的降解。研究结果表明,石油烃浓度低于1 000 mg/kg时对玉米的根系生长有一定的刺激生长作用,随着石油烃浓度的增加,刺激根长生长的作用逐渐降低,研究结果表明,水稻根长受石油烃影响较小。通过对不同处理土壤中石油烃降解的研究结果表明,土壤中种植水稻对石油烃有一定的降解作用,但是不同处理下土壤中的石油烃降解率不同,其中水稻微生物联合处理下土壤中石油烃的降解速率最快,培养期内的降解效率达到53.3%。 相似文献
2.
3.
4.
石油污染土壤的生物修复室内模拟实验研究 总被引:1,自引:0,他引:1
在实验室模拟的条件下,利用从克拉玛依的石油污染土壤中筛选出的4株高效降解菌,以石油烃降解率、脱氢酶活性、呼吸强度、微生物量碳氮和土壤毒性作为评价指标,研究不加生物菌剂不翻耕、不加生物菌剂翻耕、加生物菌剂不翻耕、加生物菌剂翻耕、加固定化菌剂不翻耕和加固定化菌剂翻耕6种不同实验条件对石油污染土壤修复的效果。结果表明,在63 d的修复过程中,加固定化菌剂翻耕实验F组的石油去除率达到了78.7%,比不加生物菌剂不翻耕实验A组的石油去除率提高了49.5%。随着土壤毒性逐渐降低,玉米(Zea mays L.)和赤子爱胜蚓(Eisenia fetida)可以在F组土壤中良好的生长,达到了修复的效果。 相似文献
5.
利用苯酚诱导获得厌氧菌群JAC1强化去除土壤中的石油烃,对其在厌氧条件下的石油烃降解条件进行了优化,得到最适降解条件为:pH 7.5~8.5,土壤总石油烃(TPH)质量浓度50 mg/kg, NaCl质量分数0.3%,JAC1接菌量0.15 mL/g。厌氧菌群JAC1对石油烃的降解符合一级动力学模型。通过气相色谱质谱联用仪分析,芳香烃较直链烷烃更难降解,推测部分长链烷烃在降解过程中会分解为短链烷烃后再进行降解。基于土壤宏基因组测序分析可知,土壤微生物群落多样性与TPH浓度呈负相关,投加JAC1后土壤中与石油烃降解有关的功能菌群相对丰度呈现出不同程度增高,说明JAC1有助于建立一个高效的微生物降解体系来强化石油烃降解。 相似文献
6.
植物-微生物联合修复石油污染土壤的实验研究 总被引:1,自引:0,他引:1
筛选高效石油降解菌并考察菌株的石油降解能力,通过植物-微生物联合修复石油污染土壤室内实验,在修复过程中测定了土壤中细菌和固氮菌,碱解氮、速效磷和速效钾的含量变化,同时采用傅立叶变换离子回旋共振质谱(ESI FT-ICR MS)考察了植物-微生物联合修复效果。结果表明,菌株3#、4#的生长适应性较强,其混合菌的降解效果最好,将其混合菌液与植物进行植物-微生物联合修复不同浓度的石油污染土壤,经过150 d的温室降解,最高降解率达到73.47%。ESI FT-ICR MS分析结果表明,与空白组相比,植物组的O1、O2和N1类等化合物相对丰度都发生了显著变化,石油污染物得到一定程度的生物降解。 相似文献
7.
微生物降解是处理土壤中石油烃(PHC)污染的有效技术,目前对PHC微生物降解的研究多集中在好氧条件下,对PHC缺氧微生物降解的研究较少,PHC缺氧降解规律尚不清楚。以PHC污染的深层土壤为对象,探究不同质量分数(500、1 500、5 000 mg·kg-1)的硫酸盐、硝酸盐或混合电子受体对土壤中土著微生物丰度、群落结构以及PHC缺氧降解的影响规律。结果表明,150 d缺氧培养后,添加相同种类电子受体的土壤处理中细菌丰度、潜在PHC降解菌(变形菌门和厚壁菌门)丰度随电子受体的质量分数增加而增加;添加相同质量分数的不同种类电子受体土壤处理中细菌丰度、潜在PHC降解菌丰度从高到低分别为硝酸盐、混合电子受体、硫酸盐。添加相同种类电子受体的土壤处理中ΣPHC (C10~C30)和C1 (C10~C16)、C2 (C17~C23)、C3 (C24~C30)组分的降解率随着加入电子受体质量分数增加而增加... 相似文献
8.
9.
10.
石油降解菌的筛选优化及其对油污土壤的修复特性 总被引:3,自引:0,他引:3
分别以牛肉膏蛋白胨-布氏哈斯培养基、蓝色凝胶培养基作为初筛和复筛培养基,从石油污染土壤中筛选出2株可产生微生物表面活性剂的石油烃降解菌。并将菌株投加到油污土壤中进行修复研究,考查了不同影响因素对修复效果的影响。研究结果表明,(1)2株菌对中度石油污染土壤有较好的修复效果,向油污土壤中直接投加菌株修复70 d时对石油烃的去除率为52%;(2)向油污土壤中投加降解菌并同时补充氮营养液,修复70 d时对土壤中总石油烃的去除率可达到75%;对土壤中正构烷烃的去除率为66%;(3)与土壤的含水率及土著菌的降解效果相比,向油污土壤中投加降解菌以及补充氮磷营养液是影响石油污染土壤修复效果的关键因素。 相似文献
11.
Árpád Ambrus 《Journal of environmental science and health. Part. B》2013,48(3):435-442
Abstract A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits. 相似文献
12.
造纸废水混凝处理中SFT助凝替代性研究 总被引:1,自引:0,他引:1
中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染 相似文献
13.
Janusz A. Pudykiewicz Anna S. Koziol 《Atmospheric environment (Oxford, England : 1994)》1998,32(24):5541
The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing. 相似文献
14.
介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠 相似文献
15.
不同泥源对厌氧氨氧化反应器启动的影响 总被引:2,自引:1,他引:1
采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。 相似文献
16.
活性炭三维电极法对印染废水的处理研究 总被引:4,自引:0,他引:4
对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25~30 V,进水pH值6.5~7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。 相似文献
17.
18.
以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径<1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径. 相似文献
19.
Volker Berding Stefan Schwartz Michael Matthies 《Environmental science and pollution research international》1999,6(1):37-43
The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters
(inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation,
on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency.
The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity
was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters),
and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity
to 961, and the maximal dimension is 21. 相似文献