钒和钨负载量对V2O5-WO3/TiO2表面形态及催化性能的影响

采用浸渍法制备了一系列不同钒和钨负载量的V2O5-WO3/TiO2催化剂样品,对样品NH3选择性催化还原NO性能进行了评价,并用BET、XRD、XPS等手段对催化剂样品的表面形态进行了表征.研究发现,钒的负载量对催化剂的比表面积和催化活性有显著影响,当钒负载量从1%升高到8%时,催化剂比表面积下降了16 m2/g,最高活性温度降低了约100℃.钨起到稳定剂和助剂的双重作用,当钒负载量为1%时,钨负载量从0升高到6%,催化剂比表面积仅下降了3 m2/g,而活性温度窗口向高温和低温各拓宽了约50℃.研究表明钒和钨负载量都能影响催化剂表面的VOx物种,但对催化剂的表面晶型没有明显影响.     

负载型燃烧催化剂La_(0.8)Ce_(0.2)CoO_3/Ce_(0.8)Zr_(0.2)O_2制备及性能研究

以复合氧化物La0.8Ce0.2CoO3为活性组分,Ce0.8Zr0.2O2固溶体为载体,采用柠檬酸络合法制备出负载型燃烧催化剂La0.8Ce0.2CoO3/Ce0.8Zr0.2O2。用XRD、BET和SEM对其进行表征,考察了焙烧温度、反应时间、反应温度及H2S存在对催化剂活性的影响。结果表明,载体表面形成了均一的钙钛矿相;该负载型催化剂对二甲苯完全氧化反应具有较高的催化活性,有良好的热稳定性、操作稳定性和强的抗H2S毒化能力。这可能是载体与负载组分之间密切的协同作用所导致。     

贫燃条件Ag-Rh/CeO_2-ZrO_2-Al_2O_3协同催化C_3H_6选择性还原NO的原位红外研究

将Ag-Rh浸渍到共沉淀法合成的Ce-Zr-Al上,制备出Ag(0.04)-Rh(x)/Ce0.5Zr0.5O2-75%Al2O3系列催化剂,采用BET比表面积、X射线衍射光谱(XRD)和原位漫反射傅里叶变换红外光谱(DRIFTS)对催化剂进行表征,并探讨催化剂在贫燃条件下选择性还原NO的活性和反应机理.结果表明,Ag-Rh双组分催化剂的活性较单组分Ag、Rh催化剂的高.Rh负载量为0.7%(质量分数)时,NO转化率达最佳(90.3%),且反应的起燃温度低、活性温度范围宽(300～500℃).DRIFTS结果显示,Rh的添加不仅有利于催化剂表面NO的吸附,而且能促进Ag催化生成关键反应中间体—CO—NH—,进而显著提高NO的转化率.     

Pd/CeO2-Al2O3对烟气中多环芳烃的催化氧化性能研究

采用浸渍法制备了不同负载量及不同钯铈比(Pd:Ce)的Pd/CeO2-Al2O3催化剂,并结合XRD、BET、SEM、O2-TPD和H2-TPR等方法对催化剂的性质进行了表征,研究了所制备的催化剂对燃煤烟气中多环芳烃(PAHs)的催化转化效率.XRD和SEM结果表明,Ce和Pd在Al2O3表面呈高度分散状态,有利于PAHs的催化氧化.BET测试表明,Ce的引入改变了催化剂表面孔径结构,提高其比表面积.O2-TPD和H2-TPR测试表明,适当钯铈比条件下制备的催化剂有较强的储氧能力和活性.催化氧化实验结果表明,所制备的Pd/CeO2-Al2O3催化剂对PAHs具有较高的转化效率,其平均转化率均在80%以上,且PAHs的毒性当量显著降低,钯铈比对PAHs的催化氧化性能影响较大,当催化剂的钯铈比为1:1时,PAHs的转化率最高,可达90%以上.     

制备条件对低温NH_3-SCR脱硝催化剂Mn-Ce/TiO_2结构与性能的影响

采用溶胶凝胶法制备了Mn-Ce/TiO2催化剂,以NH3为还原剂,通过程序升温反应考察其选择性催化还原NO的催化性能.同时,着重探讨了焙烧温度、焙烧时间、活性物质负载量及Mn、Ce负载比例对催化剂结构和性能的影响,并用BET、XRD等对催化剂进行了表征.结果表明,活性组分负载量由0增至20%时,NO转化率随着负载量的增加而提高,当(Mn+Ce)质量分数为20%,催化剂活性最高,此后随着活性组分负载量的增加,NO转化率明显下降;Mn与Ce的负载比例为0.85∶0.15时,催化剂比表面积最大,为112.31m2·g-1;焙烧温度500℃时催化剂晶相均为TiO2锐钛矿型结构,焙烧温度升高至600℃,催化剂晶相为TiO2锐钛矿型和金红石型混合结构,且催化剂比表面积急剧减小;焙烧时间对催化剂晶相结构影响不大,焙烧时间为5h时,Mn-Ce/TiO2的脱硝性能最好.     

Pt负载的铈锆固溶体的催化性能与表征

用柠檬酸法制备了CexZr1-xO(2x=0.5～1.0)铈锆固溶体,用浸渍法分别在铈锆固溶体上负载0.5%的Pt。用热重法(TG)测试了催化剂对碳烟的催化活性,Pt/Ce0.8Zr0.2O2显示了最高的催化活性。采用比表面(BET),X-射线衍射仪(XRD)和红外仪(FTIR)对催化剂进行了测试。结果表明:催化剂催化燃烧碳烟的活性与催化剂比表面积大小有关,可能是由于Pt在比表面积大的固溶体表面分散得更好,有利于氧溢出,促进碳烟的燃烧。     

Mn/Ce复合催化剂湿式氧化降解高浓度吡虫啉农药废水的研究

通过共沉淀法制备了用于湿式氧化吡虫啉农药废水的Mn/Ce复合催化剂,利用BET比表面积测定和XRD对催化剂进行了表征,研究了焙烧温度对Mn/Ce催化剂活性及稳定性的影响,探讨了湿式催化氧化吡虫啉农药废水的适宜反应温度和氧分压.结果表明,Mn/Ce催化剂晶粒细小,晶粒尺寸小于15nm;适当降低焙烧温度,对减小催化剂晶粒、增加比表面积、提高活性有利,但会使金属溶出量增大、稳定性下降;提高反应温度,湿式催化氧化反应速率加快,而氧分压大于1.6MPa后,反应速率不受氧分压影响;使用该催化剂,在温度190℃、氧分压1.6MPa、进水pH为6.21的条件下经120min处理,COD去除率达93.1%;Mn/Ce复合催化剂对湿式氧化吡虫啉农药废水显示较好的活性和稳定性.     

V2O5/CeO2催化剂用于低温NH3-SCR的性能研究

采用浸渍法制备了系列V2O5/CeO2催化剂,用于低温NH3选择性催化还原(NH3-SCR)NO.同时,考察了催化剂中V2O5负载量和煅烧温度对催化活性的影响,并运用SEM,BET和XRD物理化学技术对催化剂进行了表征.结果表明,V2O5/CeO2催化剂对模拟烟气中的NO转化呈现出较高的活性,但是V2O5负载量和催化剂的催化活性并不呈线性递增的关系.当V2O5负载量超过10%时,催化剂的催化活性开始下降.随着煅烧温度的升高,由于钒酸铈的生成,催化剂的催化活性下降.400℃为最佳煅烧温度.     

坡缕石负载Mn-Cu催化剂催化燃烧甲苯研究

作者采用浸渍法制备了一系列不同温度焙烧的Mn-Cu/Pal-T催化剂,用于甲苯催化燃烧反应。结合XRD、BET、SEM、H2-TPR、NH3-TPD、XPS多种测试手段来分析催化剂的表面结构和化学态。结果表明,焙烧温度对催化剂催化燃烧甲苯性能有重要影响,因为其会导致催化剂物化性质的变化。在400℃焙烧制得的催化剂拥有最佳的催化氧化甲苯活性,甲苯完全转化温度仅需335℃。Mn-Cu/Pal-400催化剂拥有相对大的比表面积,CuO和Mn₂O₃活性物种在其表面高度分散。同时,拥有最佳的氧化还原性、最高比例的路易斯酸、最多的氧空穴和活性氧物种,这些均有利于甲苯深度氧化。相比之下,700℃下焙烧的催化剂Mn-Cu/Pal-700呈现最小的比表面积和路易斯酸比例、最少的活性氧物种和最差的氧迁移性,这无疑会导致最差的甲苯氧化性能。     

交通运输业废物处理与综合利用

X734.201200601632Ce/Zr系列催化剂上碳颗粒物燃烧行为/朱玲(中科院生态环境研究中心)…∥环境科学/中科院生态环境研究中心.-2005,26(5).-7～11环图X-5分别在TG和TPO上考察了CeO2,ZrO2及不同Ce/Zr比的CexZr1-xO2固溶体催化剂上soot的燃烧性能,同时考察了反应气氛对活性的影响。结果表明:Ce基催化剂能明显降低soot的起燃温度,Ce/Zr比的不同导致CexZr1-xO2催化剂性能的差异。反应的速度控制步骤随O2浓度的不同而改变;H2O对Ce0.5Zr0.5O2上soot的氧化活性基本没有影响;由于NO氧化产生的NO2具有更强的氧化能力,因此NO对soot的燃…     

Complete catalytic oxidation of o-xylene over Ce02 nanocubes

The activities of CeO2 nanocubes calcined at different temperatures were tested for catalytic oxidation of o-xylene. Using CeO2 nanocubes as catalysts, complete catalytic oxidation of o-xylene was achieved below 210℃. The CeO2 nanomaterials were characterized by means of BET, X-ray diffraction (XRD), transmission electron microscopy (TEM), and high-resolution transmission electron microscopy (HRTEM). From the TEM images, all Ce02 nanocubes displayed cubic morphology irrespective of calcination temperature. The HRTEM images revealed that these nanocubes were enclosed by reactive {001}planes, which may contribute to the intrinsically catalytic property of o-xylene oxidation. The higher activity of Ce02 nanocubes calcined at 550℃ than those calcined at above 550℃ was attributed to their smaller crystallite size and larger surface area. The influences of reaction conditions were also studied, which found that a higher reaction temperature was necessary for complete catalytic oxidation of o-xylene at higher weight hourly space velocity (WHSV) and o-xylene concentration.     

Unraveling SO2-tolerant mechanism over Fe2（SO4）3/TiO2 catalysts for NOx reduction

Developing low-temperature SO₂-tolerant catalysts for the selective catalytic reduction of NO_x is still a challenging task. The sulfation of active metal oxides and deposition of ammonium bisulfate deactivate catalysts, due to the difficult decomposition of the as-formed sulfate species at low temperatures（<300 °C）. In recent years, metal sulfate catalysts have attracted increasing attention owing to their good catalytic activity and strong SO₂ tolerance at hi...     

Complete catalytic oxidation of o-xylene over CeO2 nanocubes

The activities of CeO2 nanocubes calcined at di erent temperatures were tested for catalytic oxidation of o-xylene. Using CeO2 nanocubes as catalysts, complete catalytic oxidation of o-xylene was achieved below 210°C. The CeO2 nanomaterials were characterized by means of BET, X-ray di raction (XRD), transmission electron microscopy (TEM), and high-resolution transmission electron microscopy (HRTEM). From the TEM images, all CeO2 nanocubes displayed cubic morphology irrespective of calcination temperature. The HRTEM images revealed that these nanocubes were enclosed by reactive f001g planes, which may contribute to the intrinsically catalytic property of o-xylene oxidation. The higher activity of CeO2 nanocubes calcined at 550°C than those calcined at above 550°C was attributed to their smaller crystallite size and larger surface area. The influences of reaction conditions were also studied, which found that a higher reaction temperature was necessary for complete catalytic oxidation of o-xylene at higher weight hourly space velocity (WHSV) and o-xylene concentration.     

不同煅烧温度制备TiO_2及光解2-氯苯甲酸

为了考察煅烧温度对TiO2结构和光催化活性的影响,以酞酸丁酯作为前驱体,利用溶胶-凝胶法在不同煅烧温度下制备TiO2,并用亚甲基蓝测试其光催化活性。TG热重分析表明,450~700℃时TiO2有晶型变化,XRD表征说明,TiO2晶型受煅烧温度影响显著,其中450~600℃煅烧制备的TiO2为锐钛矿型,650℃煅烧时TiO2出现金红石晶型;亚甲基蓝光解实验结果表明,煅烧温度显著影响TiO2的光催化活性,其中,450~600℃煅烧TiO2对亚甲基蓝光解效果较好,光降解2.5h后降解率高达95%~97%;550℃煅烧制备的锐钛矿型TiO2对2-氯苯甲酸有一定光解催化效果,紫外光解4h后降解率高达80%左右,光解过程符合零级动力学模式。     

Photocatalytic performance of TiO2 catalysts modified by H3PW12O40, ZrO2 and CeO2

The binary composite photo-catalysts CeO2/TiO2, ZrO2/TiO2 and the ternary composite photo-catalysts H3PW12O40-CeO2/TiO2,H2PW12O40-ZrO2/TiO2 were prepared by sol-gel method. The catalysts were characterized by thermogravimetric-differential thermal analysis (TG-DTA), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The photocatalyfic elimination of methanol was used as model reaction to evaluate the photocatalytic activity of the composite catalysts under ultraviolet light irradiation. The effects of doped content, activation temperature, time, initial concentration of methanol and gas flow rate on the catalytic activity were investigated. The results showed that after doping a certain amount of CeO2 and ZrO2, crystaniTation process of TiO2 was restrained, particles of catalysts are smaller and more uniform. Doping ZrO2 not only significantly improved the catalytic activity, but also increased thermal stability. Doping H3PW12O40 also enhanced the catalytic activity. The catalytic activities of binary and ternary composite photocatalysts were significantly higher than tin-doped TiO2. The dynamics law of photocatalytic reaction over the binary CeO2/TiO2 and ZrO2/TiO2 catalysts has been studied. The activation energy 15.627 and 15.631 kJ/mol and pre-exponential factors 0.5176 and 0.9899 s-1 over each corresponding catalyst were obtained. This reaction accords to the first order dynamics law.     

锰前驱体对MnO_x/TiO_2催化剂低温选择性催化还原NO_x影响

以醋酸锰和硝酸锰为前趋体通过浸渍法制备了MA和MN两种系列的MnOx/TiO2催化剂,结合BET、XRD、TPR及FT-IR等手段对催化剂进行了表征,并进行了比较,同时对两种系列的催化剂进行了选择催化还原脱硝的活性测试。结果表明,MA和MN均具有良好的低温催化活性,脱销效率随温度的变化趋势基本相同,在80℃时已经达到80%的脱硝效率;随着温度的升高,在200℃时效率上升至接近100%。通过对催化剂性能测试比较表明,锰的含量对于催化剂的活性有一定的影响。总体上看,MN具有更好的活性,脱销效率较高,并且其活动的窗口也是相对更宽,可能是因为以硝酸锰为前躯体制的的催化剂中MnO2的含量相对较多,即两类前驱体在制备过程中与载体之间的相互作用不同,导致最终催化剂表面活性组分MnOX结构和价态的不同,从而影响催化剂的低温活性。     

Iron-doped Mn-Ce/TiO2 catalyst for low temperature selective catalytic reduction of NO with NH3

The catalysts of iron-doped Mn-Ce/TiO 2(Fe-Mn-Ce/TiO 2) prepared by sol-gel method were investigated for low temperature selective catalytic reduction(SCR) of NO with NH 3.It was found that the NO conversion over Fe-Mn-Ce/TiO 2 was obviously improved after iron doping compared with that over Mn-Ce/TiO 2.Fe-Mn-Ce/TiO 2 with the molar ratio of Fe/Ti = 0.1 exhibited the highest activity.The results showed that 96.8% NO conversion was obtained over Fe(0.1)-Mn-Ce/TiO 2 at 180°C at a space velocity of 50,000 hr 1.Fe-Mn-Ce/TiO 2 exhibited much higher resistance to H 2 O and SO 2 than that of Mn-Ce/TiO 2.The properties of the catalysts were characterized using X-ray diffraction(XRD),N 2 adsorption,temperature programmed desorption(NH 3-TPD and NOx-TPD),and Xray photoelectron spectroscopy(XPS) techniques.BET,NH3-TPD and NOx-TPD results showed that the specific surface area and NH3 and NOx adsorption capacity of the catalysts increased with iron doping.It was known from XPS analysis that iron valence state on the surface of the catalysts were in Fe3+ state.The doping of iron enhanced the dispersion and oxidation state of Mn and Ce on the surface of the catalysts.The oxygen concentrations on the surface of the catalysts were found to increase after iron doping.Fe-Mn-Ce/TiO2 represented a promising catalyst for low temperature SCR of NO with NH3 in the presence of H2 O and SO2.     

V2O5/TiO2催化剂脱除NO的研究

采用了等体积浸渍法制备二氧化钛负载钒氧化物催化剂（V2O5/TiO2）,研究了V2O5负载量、反应温度、烟气流量、氨氮比以及运行时间各因素对NH3选择性催化还原NO反应（SCR）效率的影响.研究结果表明：经过500℃温度下煅烧,烟气流量为200ml/min,负载量为7wt％的V2O5/TiO2催化剂,在400℃温度下反应,NO脱除率可达70.5％.     

超声波浸渍法制备V_2O_5-WO_3/TiO_2选择性催化还原脱硝催化剂

采用超声波浸渍法、传统浸渍法制备一系列V2O5-WO3/TiO2催化剂,对催化剂的反应活性进行考察。研究表明:与普通浸渍法相比,超声波浸渍法可以提高催化剂的脱硝效率,拓宽催化反应的温度窗口。超声波浸渍时间和超声波功率对催化剂的反应活性有较大影响。浸渍时间增加,催化剂脱硝效率也随之提高。超声波功率增加,催化剂的脱硝效率先提高后降低。在超声波频率28 kHz,超声波功率400 W,超声作用时间1.5 h,超声水粉比为100 mL H2O/10 g TiO2的条件下,制得的V2O5-WO3/TiO2脱硝催化剂脱硝效率接近100%。通过SEM对制备的催化剂进行表征,超声波浸渍法制备的催化剂的活性成分在载体上分散更加均匀。     

Mn-Ce-Co/TiO2催化剂低温脱硝活性研究

以纳米TiO2为载体,通过浸渍法制备一系列改性Mn-Ce/TiO2脱硝催化剂.通过实验考察不同元素组分催化剂的脱硝活性,同时探讨金属氧化物掺杂对提高催化剂低温脱硝活性的机理.活性测试结果显示,Co掺杂能最有效地提高Mn-Ce/TiO2催化剂在低温段的SCR脱硝活性,在n(Co):n(TiO2)=0.08～0.10、体积空速为35100h-1的条件下,催化剂在120℃时就能达到80%以上的NO去除率,140℃左右时的NO去除率接近100%.BET、XRD、TPR、TPD等表征测试结果表明,Co掺杂可改进Mn-Ce/TiO2催化剂的物化特性,增加催化剂表面的活性酸位点及活性氧数量,提高催化剂的氧化还原能力,从而提高Mn-Ce/TiO2催化剂低温SCR脱硝活性.