Aerosol physical,chemical and optical properties during the Rocky Mountain Airborne Nitrogen and Sulfur study

During the Rocky Mountain Airborne Nitrogen and Sulfur (RoMANS) study, conducted during the spring and summer of 2006, a suite of instruments located near the eastern boundary of Rocky Mountain National Park (RMNP) measured aerosol physical, chemical and optical properties. Three instruments, a differential mobility particle sizer (DMPS), an optical particle counter (OPC), and an aerodynamic particle sizer (APS), measured aerosol size distributions. Aerosols were sampled by an Interagency Monitoring of Protected Visual Environments (IMPROVE) sampler and a URG denuder/filter-pack system for compositional analysis. An Optec integrating nephelometer measured aerosol light scattering. The spring time period had lower aerosol concentrations, with an average volume concentration of 2.2 ± 2.6 μm³ cm^?3 compared to 6.5 ± 3.9 μm³ cm^?3 in the summer. During the spring, soil was the single largest constituent of PM_2.5 mass, accounting for 32%. During the summer, organic carbon accounted for 60% of the PM_2.5 mass. Sulfates and nitrates had higher fractional contributions in the spring than the summer. Variability in aerosol number and volume concentrations and in composition was greater in the spring than in the summer, reflecting differing meteorological conditions. Aerosol scattering coefficients (b_sp) measured by the nephelometer compared well with those calculated from Mie theory using size distributions, composition data and modeled RH dependent water contents.     

The physical characteristics of sulfur aerosols

A review of the physical characteristics of sulfur-containing aerosols, with respect to size distribution of the physical distributions, sulfur distributions, distribution modal characteristics, nuclei formation rates, aerosol growth characteristics, and in situ measurement, has been made.Physical size distributions can be characterized well by a trimodal model consisting of three additive lognormal distributions.When atmospheric physical aerosol size distributions are characterized by the trimodal model, the following typical modal parameters are observed:1. Nuclei mode – geometric mean size by volume, DGV_n, from 0.015 to 0.04 μm. σ_gn=1.6, nucler mode volumes from 0.0005 over the remote oceans to 9 μm³ cm⁻³ on an urban freeway.2. Accumulation mode – geometric mean size by volume, DGV_a, from 0.15 to 0.5 μm, σ_ga=1.6–2.2 and mode volume concentrations from 1 for very clean marine or continental backgrounds to as high as 300 μm³ cm⁻³ under very polluted conditions in urban areas.3. Coarse particle mode – geometric mean size by volume, DGV_c, from 5 to 30 μm, σ_gn=2–3, and mode volume concentrations from 2 to 1000 μm³ cm⁻³.It has also been concluded that the fine particles (D_p<2 μm) are essentially independent in formation, transformation and removal from the coarse particles (D_p>2 μm).Modal characterization of impactor-measured sulfate size distributions from the literature shows that the sulfate is nearly all in the accumulation mode and has the same size distribution as the physical accumulation mode distribution.Average sulfate aerodynamic geometric mean dia. was found to be 0.48±0.1 μm (0.37±0.1 μm vol. dia.) and σ_g=2.00±0.29. Concentrations range from a low of about 0.04 μg m⁻³ over the remote oceans to over 8 μg m⁻³ under polluted conditions over the continents.Review of the data on nucleation in smog chambers and in the atmosphere suggests that when SO₂, is present, SO₂-to-aerosol conversion dominates the Aitken nuclei count and, indirectly, through coagulation and condensation, the accumulation mode size and concentration. There are indications that nucleation is ubiquitous in the atmosphere, ranging from values as low as 2 cm⁻³ h⁻¹ over the clean remote oceans to a high of 6×10⁶ cm⁻³ h⁻¹ in a power plant plume under sunny conditions.There is considerable theoretical and experimental evidence that even if most of the mass for the condensational growth of the accumulation mode comes from hydrocarbon conversion, sulfur conversion provides most of the nuclei.     

Aerosol scattering properties in northern China

The aerosol scattering properties were investigated at two continental sites in northern China in 2004. Aerosol light scattering coefficient (σ_sp) at 525 nm, PM₁₀, and aerosol mass scattering efficiencies (α) at Dunhuang had a mean value of 165.1±148.8 M m⁻¹, 157.6±270.0 μg m⁻³, and 2.30±3.41 m² g⁻¹, respectively, while these values at Dongsheng were, respectively, 180.2±151.9 M m⁻¹, 119.0±112.9 μg m⁻³, and 1.87±1.41 m² g⁻¹. There existed a seasonal variability of aerosol scattering properties. In spring, at Dunhuang PM₁₀, σ_sp, and α were 184.1±211.548 μg m⁻³, 126.3±89.6 M m⁻¹, and 1.05±0.97 m² g⁻¹, respectively, and these values at Dongsheng were 146.4±142.1 μg m⁻³, 183.4±81.7 M m⁻¹, and 1.98±1.52 m² g⁻¹, respectively. However, in winter at Dunhuang PM₁₀, σ_sp, and α were 158.1±261.4 μg m⁻³, 303.3±165.2 M m⁻¹, and 3.17±1.93 m² g⁻¹, respectively, and these values at Dongsheng were 155.7±170.1 μg m⁻³, 304.4±158.1 M m⁻¹, and 2.90±1.72 m² g⁻¹, respectively. σ_sp and α in winter were higher than that in spring at both the sites, which coincides with the characteristics of dust aerosol and pollution aerosol. Overall, the dominant aerosol types in spring and winter at both sites in northern China are dust aerosol and pollution aerosol, respectively.     

Journey-time exposure to particulate air pollution

Journey-time exposures to particulate air pollution were investigated in Leicester, UK, between January and March 2005. Samples of TSP, PM₁₀, PM_2.5, and PM₁ were simultaneously collected using light scattering devices whilst journeys were made by walking an in-car. Over a period of two months, 33 pairs of walking and in-car measurements were collected along two circular routes. Average exposures while walking were seen to be higher than those found in-car for each of the particle fractions: average walking to in-car ratios were 1.2 (± 0.6), 1.5 (± 0.6), 1.3 (± 0.6), and 1.4 (± 0.6) μg m⁻³ for coarse (TSP–PM₁₀), intermediate (PM₁₀–PM_2.5), fine (PM_2.5–PM₁), and very fine particles (PM₁), respectively. Correlations between walking and in-car exposures were seen to be weak for coarse particles (r=0.10, p=0.58), moderate for the intermediate particles (r=0.49, p<0.01) but strong for fine (r=0.89, p<0.01) and very fine (r=0.90, P<0.01) particles. PM₁₀ exposures while walking were on average 70% higher than a nearby roadside fixed-site monitor whilst in-car exposures were 25% higher than the same fixed-site monitor. Particles with an aerodynamic diameter of less than 2.5 μm were seen to be highly correlated between walking and in-car particle exposures and a rural fixed-site monitor about 30 km south of Leicester.     

Influence of the surface microlayer on atmospheric deposition of aerosols and polycyclic aromatic hydrocarbons

Atmospheric dry deposition is an important process for the introduction of aerosols and pollutants to aquatic environments. The objective of this paper is to assess, for the first time, the influence that the aquatic surface microlayer plays as a modifying factor of the magnitude of dry aerosol deposition fluxes. The occurrence of a low surface tension (ST) or a hydrophobic surface microlayer has been generated by spiking milli-Q water or pre-filtered seawater with a surfactant or octanol, respectively. The results show that fine mode (<2.7 μm) aerosol phase PAHs deposit with fluxes 2–3 fold higher when there is a low ST aquatic surface due to enhanced sequestration of colliding particles at the surface. Conversely, for PAHs bound to coarse mode aerosols (>2.7 μm), even though there is an enhanced deposition due to the surface microlayer for some sampling periods, the effect is not observed consistently. This is due to the importance of gravitational settling for large aerosols, rendering a lower influence of the aquatic surface on dry deposition fluxes. ST (mN m⁻¹) is identified as one of the key factor driving the magnitude of PAH dry deposition fluxes (ng m⁻² d⁻¹) by its influence on PAH concentrations in deposited aerosols and deposition velocities (v_d, cm s⁻¹). Indeed, v_d values are a function of ST as obtained by least square fitting and given by Ln(v_d)=−1.77 Ln(ST)+5.74 (r²=0.95) under low wind speed (average 4 m s⁻¹) conditions.     

Seasonal and shorter-term variations in particulate atmospheric nitrate in Baltimore

Fine particle nitrate concentrations were measured at 10-min intervals for approximately 9.5 months beginning on 14 February 2002, at the Baltimore Supersite Ponca St. location using an R&P 8400N semi-continuous monitor. The measurement results were used to characterize seasonal and shorter-term excursions in nitrate concentrations and determine their influence on PM_2.5 concentrations. Over the 9.5-month study period, nitrate levels of 1.7±1.6 μg m⁻³ accounted for 11.4% of the PM_2.5 mass. Monthly averages ranged from 0.8 μg m⁻³ in August to 2.9 μg m⁻³ in November, and accounted for 4.7–17.3% of monthly PM_2.5 mass. Hourly averages, however, were often larger, especially in the colder months, owing to numerous relatively short-term transients, where hourly nitrate concentrations exceeded 5.0 μg m⁻³. These often occurred along with NO_x and ultrafine particle transients during the morning commute hours.A total of 275 short-term transients (31.7% of the total) exceeding 1.0 μg m⁻³ were identified. These were associated with one of three sets of conditions. The first, most typical (177, i.e. 64.4% of the 275 incidences), is characterized by high NO_x typically between 0500 and 0800EST and is attributed to early morning commute traffic activity. The second type occurred during the afternoon due to photochemical activity. The excursions in the afternoon occurred infrequently (only 9.5% of all the observed transients) during the study period and were characterized by less elevated nitrate concentrations than morning and nighttime transients. The third (72, i.e. 26.2% of the 275 transients) occurred at night, typically between 2000EST and 0200EST.Multiple linear regression analysis between nitrate excursions and volume size distributions indicates that particulate nitrate observed is closely related to the near accumulation (0.1–0.2 μm) and droplet modes (0.5–1.0 μm) in the morning hours, and associated with the droplet (0.5–1.0 μm) and coarse modes (1.0–2.5 μm) for nighttime transients, suggesting that processes governing particulate nitrate formation depend on time-of-day.     

Aerosol mass-size distributions at a tropical coastal environment: response to mesoscale and synoptic processes

Regular measurements of total mass concentration and mass-size distribution of near-surface aerosols, made using a ten-channel Quartz Crystal Microbalance (qcm) Impactor for the period October 1998–December 1999 at the tropical coastal station Trivandrum (8.5°N, 77°E), are used to study the response of aerosol characteristics to regional mesoscale and synoptic processes. Results reveal that aerosol mass concentrations are generally higher under land breeze conditions. The sea breeze generally has a cleansing effect, depleting the aerosol loading. The continental air (LB regime) is richer in accumulation mode (submicron) aerosols than the marine air. On a synoptic scale, aerosol mass concentration in the submicron mode decreased from an average high value of ∼86 μg m⁻³ during the dry months (January–March) to ∼11 μg m⁻³ during the monsoon season (June–September). On the contrary mass concentration in the supermicron mode increased from a low value of ∼15 μg m⁻³ during the dry months to reach a comparatively high value of ∼35 μg m⁻³ during April, May. Correspondingly, the effective radius (R_eff) increased from a low value of 0.15–0.17 μm to ∼0.3 μm indicating a seasonal change in the size distribution. The mass-size distribution shows mainly three modes, a fine mode (∼0.1 μm); a large mode (∼0.5 μm) and a coarse mode (∼3 μm). The fine mode dominates in winter. In summer the large mode becomes more conspicuous and the coarse mode builds up. The fine mode is highly reduced in monsoon and the large and coarse modes continue to remain high (replenished) so that their relative dominance increases. The size distribution tends to revert to the winter pattern in the post-monsoon season. Accumulation (submicron) aerosols account for ∼98% of the total surface area and ∼70% of the total volume of aerosols during winter. During monsoon, even though they still account for ∼90% of the area, their contribution to the volume is reduced to ∼50%; the coarse aerosols account for the rest.     

Size-resolved sulfate and ammonium measurements in marine boundary layer over the North and South Pacific

Marine background levels of non-sea-salt- (nss-) SO₄²⁻ (5.0–9.7 neq m⁻³), NH₄⁺ (2.1–4.4 neq m⁻³) and elemental carbon (EC) (40–80 ngC m⁻³) in aerosol samples were measured over the equatorial and South Pacific during a cruise by the R/V Hakuho-maru from November 2001 to March 2002. High concentrations of nss-SO₄²⁻ (47–94 neq m⁻³), NH₄⁺ (35–94 neq m⁻³) and EC (130–460 ngC m⁻³) were found in the western North Pacific near the coast of the Asian continent under the influence of the Asian winter monsoon. Particle size distributions of ionic components showed that the equivalent concentrations of nss-SO₄²⁻ were balanced with those of NH₄⁺ in the size range of 0.06<D<0.22 μm, whereas the concentration ratios of NH₄⁺ to nss-SO₄²⁻ in the size range of D>0.22 μm were decreased with increase in particle size. We estimated the source contributions of those aerosol components in the marine background air over the equatorial and South Pacific. Biomass burning accounted for the large fraction (80–98% in weight) of EC and the minor fraction (2–4% in weight) of nss-SO₄²⁻. Marine biogenic source accounted for several tens percents of NH₄⁺ and nss-SO₄²⁻. In the accumulation mode, 70% of particle number existed in the size range of 0.1<D<0.2 μm. In the size rage of 0.06<D<0.22 μm, the dominant aerosol component of (NH₄)₂SO₄ would be mainly derived from the marine biogenic sources.     

Behavioral and environmental determinants of personal exposures to PM2.5 in EXPOLIS – Helsinki,Finland

Behavioral and environmental determinants of PM_2.5 personal exposures were analyzed for 201 randomly selected adult participants (25–55 years old) of the EXPOLIS study in Helsinki, Finland. Personal exposure concentrations were higher than respective residential outdoor, residential indoor and workplace indoor concentrations for both smokers and non-smokers. Mean personal exposure concentrations of active smokers (31.0±31.4 μg m⁻³) were almost double those of participants exposed to environmental tobacco smoke (ETS) (16.6±11.8 μg m⁻³) and three times those of participants not exposed to tobacco smoke (9.9±6.2 μg m⁻³). Mean indoor concentrations of PM_2.5 when a member of the household smoked indoors (20.8±23.9 μg m⁻³) were approximately 2.5 times the concentrations of PM_2.5 when no smoking was reported (8.2±5.2 μg m⁻³). Interestingly, however, both mean (8.2 μg m⁻³) and median (6.9 μg m⁻³) residential indoor concentrations for non-ETS exposed participants were lower than residential outdoor concentrations (9.5 and 7.3 μg m⁻³, respectively). In simple linear regression models residential indoor concentrations were the best predictors of personal exposure concentrations. Correlations (r²) between PM_2.5 personal exposure concentrations of all participants, both smoking and non-smoking, and residential indoor, workplace indoor, residential outdoor and ambient fixed site concentrations were 0.53, 0.38, 0.17 and 0.16, respectively. Predictors for personal exposure concentrations of non-ETS exposed participants identified in multiple regression were residential indoor concentrations, workplace concentrations and traffic density in the nearest street from home, which accounted for 77% of the variance. Subsequently, step-wise regression not including residential and workplace indoor concentrations as input (as these are frequently not available), identified ambient PM_2.5 concentration and home location, as predictors of personal exposure, accounting for 47% of the variance. Ambient fixed site PM_2.5 concentrations were closely related to residential outdoor concentrations (r²=0.9, p=0.000) and PM_2.5 personal exposure concentrations were higher in summer than during other seasons. Personal exposure concentrations were significantly (p=0.040) higher for individuals living downtown compared with individuals in suburban family homes. Further analysis will focus on comparisons of determinants between Helsinki and other EXPOLIS centers.     

Characterisation of fresh particulate vehicular exhausts near a Paris high flow road

Simultaneous continuous measurements of PM_2.5, PM₁₀, black carbon mass (BCae), Black smoke (BS) and particle number density (N) were conducted in the close vicinity of a high traffic road around Paris during a three-month period beginning in August 1997. In parallel some aerosol collection was performed on filters in order to assess the black carbon (BC), organic carbon (OC) and water soluble organic fractions (WSOC) of the freshly emitted traffic aerosols. The high hourly concentrations of PM_2.5 (39±20 μg m⁻³), BCae (14±7 μg m⁻³), and N (220,000±115,000 cm⁻³), were found to be well correlated with each other. On average PM_2.5 represented 66±13% of PM₁₀ and appears to be composed primarily of BC (43±20%). On the contrary no correlation was found between PM_2.5 and the coarse (PM₁₀–PM_2.5) mass fractions which was attributed to resuspension processes by vehicles. Black carbon mass concentrations obtained from both filter analyses (BC) and Aethalometre data (BCae) show a good agreement suggesting that the Aethalometre calibration based on a black carbon specific attenuation coefficient (σ) of 19 m² g⁻¹ is well adapted to nearby roadside measurements. Daily BC (used as a surrogate for fine particles) concentrations and wind speed were found to be anti-correlated. Average daily variations of BC could be related to traffic intensity and regime as well as to the boundary layer height. As expected for freshly emitted traffic aerosols, filter analyses indicated a high BC/TC ratio (29±5%) and a low mean WSOC/OC ratio (12.5±5%) for the bulk aerosol. For these two ratios no day/night differences were observed, the sampling station being probably too close to traffic to evidence photochemical modification of the aerosol phase. Finally, a linear relationship was found between BC and BS hourly concentrations (BC=0.10×BS+1.18; r²=0.93) which offers interesting perspectives to retrieve BC concentrations from existing BS archives.     

Generation and growth of aerosols over Pune,India

The measured physical size distributions of sub-micron particles during cold season at Pune, India are analyzed to explore the characteristics of nucleation and growth properties. Preliminary analysis of aerosol size distribution in time-series shows large increase in number concentration due to nucleation events between 0800 h and 1030 h at this location. The observable quantities such as condensable vapor concentration (C), its source rate (Q), growth rate (GR) and condensable sink (CS) are estimated from the time-series evolutions of aerosol size distributions. The concentration of vapor and its source rate were about 19.8 ± 2.15 × 10⁷ molecules cm^?3 and 1.28 ± 0.084 × 10⁷ cm^?3 s^?1 respectively. The average condensation sink and growth rate were 7.1 ± 0.4 × 10^?2 s^?1 and 16.95 ± 1.86 nm h^?1 respectively during the growth period. The values are high enough to trigger the nucleation bursts and enhance subsequent growth rates of nucleation mode particles at this location. The magnitudes are in the range of those observed at New Delhi, India and much higher than those of European cities. The ratio of apparent to real nucleation rate is found to be a measure of number concentration of freshly produced particles by photo-chemical nucleation. The predicted number concentrations corresponding to measured distributions of mid-point diameter increases with the size for both 1 nm nucleated clusters and 3 nm particles. The database of all the possible event days and the event characteristics forms the basis for future works into the causes and implications of atmospheric particle formation at this location.     

PM2.5 particles and size-segregated ionic species measured during fall season in three urban sites in Korea

Twelve hours integrated fine particles (PM_2.5) and 24-h average size-segregated particles were collected to investigate the chemical characteristics and to determine the size distribution of ionic species during October–December 1999 in three cities of different urban scale; Chongju, Kwangju, and Seoul, Korea. Concentrations of 5-min PM_2.5 black carbon (BC) and hourly criteria air pollutants (PM₁₀, CO, NO_x, SO₂, and O₃) were also measured using the Aethalometer and ambient air monitoring system, respectively.Highest PM_2.5 mass concentrations at Chongju, Kwangju, and Seoul sites were 63.0, 77.9, and 143.7 μg m⁻³, respectively. For the time period when highest PM_2.5 mass occurred, BC level out of PM_2.5 chemical species was highest at both Chongju and Kwangju, and highest NO₃⁻ (23.6 μg m⁻³) followed by BC (23.1 μg m⁻³) were observed at Seoul site, indicating that highest PM_2.5 pollution is closely associated with the traffic emissions. Strong relationships of Fe with BC and Zn at both Kwangju and Seoul sites support that the Fe and Zn measured there are originated partly from same source as BC, i.e. diesel traffics. However, it is suggested that the Fe measured at Chongju is most likely derived from dispersion of soil dust.The size distributions of SO₄²⁻, NO₃⁻, and NH₄⁺ ionic species indicated similar unimodal distributions at all sampling sites. However, different unimodal patterns in the accumulation mode size range with a peak in the smaller size (0.28–0.53 μm, condensation mode) in both Kwangju and Seoul, and in the relatively larger size (0.53–1.0 μm, droplet mode) in Chongju, were found. The potassium ion under the study sites dominates in the fine mode, and its size distribution showed unimodal character with a maximum in the size range 0.56–1.0 μm.     

Biogenic VOC emissions from fresh leaf mulch and wood chips of Grevillea robusta (Australian Silky Oak)

The emissions of VOC from freshly cut and shredded Grevillea robusta (Australian Silky Oak) leaves and wood have been measured. The VOC emissions from fresh leaf mulch and wood chips lasted typically for 30 and 20 h respectively, and consisted primarily of ethanol, (E)-2-hexenal, (Z)-3-hexen-1-ol and acetaldehyde. The integrated emissions of the VOCs were 0.38±0.04 g kg⁻¹ from leaf mulch, and 0.022±0.003 g kg⁻¹ from wood chips. These emissions represent a source of VOCs in urban and rural air that has previously been unquantified and is currently unaccounted for. These VOCs from leaf mulch and wood chips will contribute to both urban photochemistry and secondary organic aerosol formation. Any CH₄ emissions from leaf mulch and wood chips were <1×10⁻¹¹ g g dry mass⁻¹ s⁻¹.     

Distribution characteristics of polycyclic aromatic hydrocarbons with particle size in urban aerosols at the roadside in Ho Chi Minh City,Vietnam

The purpose of this study was to characterize size distributions of atmospheric polycyclic aromatic hydrocarbons (PAHs) with 4–6 rings at the roadside in Ho Chi Minh City, Vietnam. Ten PAHs (fluoranthene, pyrene, triphenylene, benzo[a]anthracene, chrysene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, benzo[ghi]perylene and indeno[1,2,3-cd]pyrene) in atmospheric particulate matters (PM) at the roadside were measured in the dry and rainy seasons in 2005 at Ho Chi Minh City, using a low-pressure cascade impactor. The PM were separated into nine fractions by their aerodynamic diameter, i.e. >9.0, 9.0–5.8, 5.8–4.7, 4.7–3.3, 3.3–2.1, 2.1–1.1, 1.1–0.7, 0.7–0.4 and <0.4 μm (a final filter). PAHs were analyzed by high-performance liquid chromatography with fluorescence detection. Total PAHs measured were higher in the rainy season than in the dry season. The mass of coarse particles occupied a higher fraction than that of fine particles in both seasons. Total PAHs were mainly concentrated in particles with aerodynamic diameter smaller than 0.4 μm. The particle size distributions of PAHs investigated were bi-modal with a peak in fine particle mode (<2.1 μm) and another peak in coarse particle mode (>2.1 μm). Generally, 5,6-ring PAHs associated mainly with fine particles and 4-ring PAHs spread out in both fine and coarse particles.     

Measurements of the physical properties of particles in the urban atmosphere

Measurements of the physical properties of particles in the atmosphere of a UK urban area have been made, including particle number count by condensation nucleus counters with different lower particle size cut-offs; particle size distributions using a Scanning Mobility Particle Sizer; total particle Fuchs surface area using an epiphaniometer and particle mass using Tapered Element Oscillating Micro-balance (TEOM) instruments with size selective (PM₁₀ and PM_2.5) inlets. Mean particle number counts at three sites range from 2.86×10⁴ to 9.60×10⁴ cm^-3. A traffic-influenced location showed a substantially higher ratio of particle number to PM₁₀ mass than a nearby background location despite being some 70 m from the roadway. Operating two condensation nucleus counters in tandem to determine particles in the 3–7 nm size range by difference showed signficant numbers of particles in this range, apparently related to homogeneous nucleation processes. Measurements with the Scanning Mobility Particle Sizer showed a clear difference between roadside size distributions and those at a nearby background location with an additional mode in the roadside samples below 10 nm diameter. Particle number counts were found to show a significant linear correlation with PM₁₀ mass (r²=0.44; n=44 for 24 h data at an urban background location), although during one period of high pollution a curvilinear relationship was found. Measurements of the diurnal variation in PM₁₀ mass, particle number count and Fuchs surface area show the same general pattern of behaviour of the three variables, explicable in terms of vehicle emission source strength and atmospheric dispersion, although the surface area growth was out of phase with the particle number and mass. It appears that particle number gives the clearest indication of recent road traffic emissions.     

Measurement and modeling of the dry deposition of peroxides

easurements of the dry deposition velocity (V_d) of hydrogen peroxide (H₂O₂) and total organic peroxides (ROOH) were made during four experiments at three forested sites. Details and uncertainties associated with the measurement of peroxide fluxes by the flux-gradient method are discussed. The results are compared to those predicted using a bulk-resistance model of the type commonly used in regional photochemical models. Good agreement between the H₂O₂ V_d measurements and a bulk resistance model is obtained when the model contains a zero surface resistance (R_c) and a common form for the laminar leaf-layer resistance (R_b) based on Schmidt and Prandtl numbers. In this case, a near-zero (<5 s m^-1) surface resistance is confirmed for H₂O₂ within experimental uncertainties. Surface resistances for ROOH were determined to be about 10–15 s m^-1 over a coniferous forest and 20–40 s m^-1 over a deciduous forest. Higher uncertainties for ROOH prevent a detailed analysis of the differences in R_c among forest types. However, the ratio of deposition velocities (ROOH/H₂O₂), computed from normalized concentration gradients, ranged from 0.28 to 0.61 (geometric mean) at the three sites. Differences in molecular diffusivities between H₂O₂ and ROOH can only account for an estimated 16% difference in V_d. Thus, the major constituent of ROOH must also be less soluble and/or less reactive than H₂O₂, which is consistent with the characteristics of methylhydroperoxide (MHP).     

Kinetics of the gas-phase reactions of NO3 radicals with ethyl acrylate,n-butyl acrylate,methyl methacrylate and ethyl methacrylate

The relative rate method has been used to determine the rate constants for the gas-phase reactions of NO₃ radicals with a series of acrylate esters: ethyl acrylate (k₁), n-butyl acrylate (k₂), methyl methacrylate (k₃) and ethyl methacrylate (k₄) at 298 ± 1 K and 760 Torr. The obtained rate constants are k₁ = (1.8 ± 0.25) × 10^?16 cm³ molecule^?1 s^?1, k₂ = (2.1 ± 0.33) × 10^?16 cm³ molecule^?1 s^?1, k₃ = (3.6 ± 1.2) × 10^?15 cm³ molecule^?1 s^?1, k₄ = (4.9 ± 1.7) × 10^?15 cm³ molecule^?1 s^?1. The experimental rate constants are in good agreement with theoretical rate constants calculated by an algorithm of the correlation between the rate constants and the orbital energies for the reactions of unsaturated VOCs with NO₃ radicals. In addition, the atmospheric lifetimes of the compound against NO₃ attack are estimated and the results show that NO₃ reactions contribute little to the atmospheric losses of acrylate esters except in polluted regions.     

Source apportionment of visibility degradation problems in Brisbane (Australia) using the multiple linear regression techniques

Different aspects of visibility degradation problems in Brisbane were investigated through concurrent visibility monitoring and aerosol sampling programs carried out in 1995. The relationship between the light extinction coefficients and aerosol mass/composition was derived by using multiple linear regression techniques. The visibility properties at different sites in Brisbane were found to be correlated with each other on a daily basis, but not correlated with each other hour by hour. The cause of scattering of light by moisture (b_sw) was due to sulphate particles which shift to a larger size under high-humidity conditions. The scattering of light by particulate matter (b_sp) was found to be highly correlated with the mass of fine aerosols, in particular the mass of fine soot, sulphate and non-soil K. For the period studied, on average, the total light extinction coefficient (b_ext) at five sites in Brisbane was 0.65×10⁻⁴ m⁻¹, considerably smaller than those values found in other Australian and overseas cities. On average, the major component of b_ext is b_sp (49% of b_ext), followed by b_ap (the absorption of light, mainly by fine soot particles, 28%), b_sg (Rayleigh scattering, 20%) and b_sw (3%). The absorption of light by NO₂ (b_ag) is expected to contribute less than 5% of b_ext. On average, the percentage contribution of the visibility degrading species to b_ext (excluding b_ag) were: soot (53%), sulphate (21%), Rayleigh scattering (20%), non-soil K (2%) and humidity (3%). In terms of visibility degrading sources, motor vehicles (including soot and the secondary products) are expected to contribute more than half of the b_ext (excluding b_ag) in Brisbane on average, followed by secondary sulphates (17%) and biomass burning (10%).     

Water-soluble organic nitrogen (WSON) in size-segregated atmospheric particles over the Eastern Mediterranean

Atmospheric water-soluble organic nitrogen (WSON) was determined on size-segregated aerosol particles collected during a two years period (2005–2006) in a remote marine location in the Eastern Mediterranean (Finokalia, Crete island). Average concentration of WSON was 5.5 ± 3.9 nmol m^?3 and 11.6 ± 14.0 nmol m^?3 for coarse (PM_1.3-10) and fine (PM_1.3) mode respectively, corresponding to 13% of Total Dissolved Nitrogen (TDN) in both modes. Air masses origin and correlation with tracers of natural and anthropogenic sources indicate that combustion process (biomass burning and fossil fuel) and African dust play an important role in regulating levels of WSON in both coarse and fine aerosol fractions. Chemical speciation of organic nitrogen pool was attempted by analyzing 47 fine aerosol samples (PM₁) for 17 free amino acids (N-FAA), dimethylamine (DMA) and trimethylamine (TMA). The average concentration of N-FAA was 0.5 ± 0.5 nmol m^?3, while the average concentration of DMA was 0.2 ± 0.8 nmol m^?3, TMA was below detection limit. The percentage contribution of N-FAA and DMA to WSON was 2.1 ± 2.3% and 0.9 ± 3.4%, respectively.     

Personal exposures to NO2 in the EXPOLIS-study: relation to residential indoor,outdoor and workplace concentrations in Basel,Helsinki and Prague

Personal exposures, residential indoor, outdoor and workplace levels of nitrogen dioxide (NO₂) were measured for 262 urban adult (25–55 years) participants in three EXPOLIS centres (Basel; Switzerland, Helsinki; Finland, and Prague; Czech Republic) using passive samplers for 48-h sampling periods during 1996–1997. The average residential outdoor and indoor NO₂ levels were lowest in Helsinki (24±12 and 18±11 μg m⁻³, respectively), highest in Prague (61±20 and 43±23 μg m⁻³), with Basel in between (36±13 and 27±13 μg m⁻³). Average workplace NO₂ levels, however, were highest in Basel (36±24 μg m⁻³), lowest in Helsinki (27±15 μg m⁻³), with Prague in between (30±18 μg m⁻³). A time-weighted microenvironmental exposure model explained 74% of the personal NO₂ exposure variation in all centres and in average 88% of the exposures. Log-linear regression models, using residential outdoor measurements (fixed site monitoring) combined with residential and work characteristics (i.e. work location, using gas appliances and keeping windows open), explained 48% (37%) of the personal NO₂ exposure variation. Regression models based on ambient fixed site concentrations alone explained only 11–19% of personal NO₂ exposure variation. Thus, ambient fixed site monitoring alone was a poor predictor for personal NO₂ exposure variation, but adding personal questionnaire information can significantly improve the predicting power.