Characterisation of PM10 atmospheric aerosols for the wet season 2005 at two sites in East Africa

Ambient daily PM₁₀ aerosol samples were collected at two sites in Tanzania in May and June 2005 (during the wet season), and their chemical characteristics were studied. The sites were a rural site in Morogoro and an urban kerbside site in Dar es Salaam. A Gent PM₁₀ stacked filter unit sampler with sequential Nuclepore polycarbonate filters, providing fine and coarse size fractions, and a PM₁₀ sampler with quartz fibre filters were deployed. Parallel collections of 24 h were made with the two samplers and the number of these collections was 13 in Morogoro and 16 in Dar es Salaam. The average mass concentration of PM₁₀ was 27 ± 11 μg/m³ in Morogoro and 51 ± 21 μg/m³ in Dar es Salaam. In Morogoro, the mean concentrations of organic carbon (OC), elemental carbon (EC), and water-soluble organic carbon (WSOC) were 6.8, 0.51, and 2.8 μg/m³, respectively. In contrast, higher mean concentrations (11.9, 4.6, and 3.3 μg/m³, respectively) were obtained for Dar es Salaam. At both sites, species and elements, such as black carbon, NH₄⁺, non-sea-salt SO₄^2?, K, and Ni (and at Dar es Salaam also V, As, Br, and Pb) were mainly present in the fine size fraction. The common crustal and sea-salt elements, including Na, Mg, Al, Si, Cl, Ca, Ti, Mn, Fe, and Sr, and also NO₃^? and P (and to a lesser extent Cu and Zn) were concentrated in the coarse particles. Aerosol chemical mass closure indicated that the PM₁₀ mass in Morogoro consisted, on average, of 48% organic matter (OM), 44% crustal matter, 4% sea salt, and 2% EC, while in Dar es Salaam OM, crustal matter, sea salt, and EC represented 37%, 32%, 9%, and 9% of the PM₁₀ mass. The contributions of the secondary inorganic aerosol (non-sea-salt sulphate, nitrate, and ammonium) were small, i.e., only 5% in total at each site. Carbonaceous materials and crustal matter were thus the most important components of the PM₁₀ mass. It is suggested that biomass burning is a major contributor to the OM; at Dar es Salaam there is also a very substantial contribution from traffic. A source apportionment calculation indicated that 68% of the OC at this site originated from traffic exhaust versus 32% from charcoal burning. The crustal matter at Morogoro is likely mainly attributable to soil dust resuspension, whereas in Dar es Salaam it is likely mostly resuspended road dust.     

Characterization of n-alkanes in PM2.5 of the Taipei aerosol

Ambient concentrations of n-alkanes with carbon number ranging from 17 to 36 were determined for PM_2.5 samples collected in Taipei city during September 1997–February 1998. The measured concentrations of particulate n-alkanes were in the range of 69–702 ng m⁻³, considerably higher than the concentration levels observed in Los Angeles and Hong Kong. The concentration distributions of n-alkanes homologues obtained in this study exhibited peaks at C₁₉, C₂₄ or C₂₅. This suggests that fossil fuel utilization, such as vehicular exhaust and lubricant residues, was an important contributor to the Taipei aerosol. Source apportionment of PM_2.5 was conducted using carbon preference index (CPI, defined as the ratio of the total concentration of particulate n-alkanes with odd carbon number to that with even carbon number) and U : R ratio (the concentration ratio of unresolved components to resolved components obtained from chromatograms). The low CPI value (0.9–1.9) and high U : R ratio (2.6–6.4) for each sample further confirmed that fossil fuel utilization was the major source of n-alkanes in ambient PM_2.5 of Taipei city. Estimates from these results showed that 69–93% of the n-alkanes in PM_2.5 of the Taipei aerosol originated from vehicular exhaust. The higher concentration level of particulate n-alkanes in the Taipei aerosol was mainly a result of vehicular emissions.     

Study of aluminium distribution and speciation in atmospheric particles of different diameters in Nanjing,China

Aluminium (Al) is one of the trace inorganic metals present in atmospheric particles. Al speciation study is essential to better evaluate the mobility, availability, and persistence of trace Al and Al species in the atmosphere. This paper reports Al distribution and speciation in atmospheric particles with aerodynamic diameters >10.0, 10.0–2.5 and <2.5 μm in the urban area of Nanjing, China. Urban particles were collected with a high-volume sampling system equipped with a cascade impactor, which effectively separates the particulate matter into three size ranges. Particulate Al was fractionated into five different forms (insoluble, oxide, organic, carbonate, and exchangeable species) by the modified five-step Tessier's sequential extraction procedure. The main points are as follows: (1) The average levels of Al in PM_2.5, PM_2.5–10 and PM_>10 are 2.02±0.35, 3.04±0.43 and 6.32±0.76 μg m⁻³, respectively, with PM_2.5, PM_2.5–10 and PM_>10 constituting respectively, 17.8±3.1%, 26.7±3.8% and 55.5±6.7% of suspended particulate matter (SPM) mass (11.38 μg m⁻³). (2) The vertical profile of airborne Al in the above three size fractions has been estimated. A significant increase in airborne Al concentrations was found for PM_2.5, PM_2.5–10 and PM_>10 as the sampling height above the ground increased from 2.5 to 17.5 m; however, there was an obvious decrease in airborne Al concentrations between 17.5 and 40.0 m. The maximum mean of total Al in PM_2.5, PM_2.5–10 and PM_>10 occurred between 12.5 and 20.0 m above the ground. (3) The distribution of Al speciation was studied. It was found that the size distribution of airborne Al species followed the order: insoluble species>oxide species>organic species>carbonate species>exchangeable species.     

PM10 and PM2.5 concentrations in Central and Eastern Europe:: results from the Cesar study

Between November 1995 and October 1996, particulate matter concentrations (PM₁₀ and PM_2.5) were measured in 25 study areas in six Central and Eastern European countries: Bulgaria, Czech Republic, Hungary, Poland, Romania and Slovak Republic. To assess annual mean concentration levels, 24-h averaged concentrations were measured every sixth day on a fixed urban background site using Harvard impactors with a 2.5 and 10 μm cut-point. The concentration of the coarse fraction of PM₁₀ (PM_10−2.5) was calculated as the difference between the PM₁₀ and the PM_2.5 concentration. Spatial variation within study areas was assessed by additional sampling on one or two urban background sites within each study area for two periods of 1 month. QA/QC procedures were implemented to ensure comparability of results between study areas. A two to threefold concentration range was found between study areas, ranging from an annual mean of 41 to 98 μg m⁻³ for PM₁₀, from 29 to 68 μg m⁻³ for PM_2.5 and from 12 to 40 μg m⁻³ for PM_10−2.5. The lowest concentrations were found in the Slovak Republic, the highest concentrations in Bulgaria and Poland. The variation in PM₁₀ and PM_2.5 concentrations between study areas was about 4 times greater than the spatial variation within study areas suggesting that measurements at a single sampling site sufficiently characterise the exposure of the population in the study areas. PM₁₀ concentrations increased considerably during the heating season, ranging from an average increase of 18 μg m⁻³ in the Slovak Republic to 45 μg m⁻³ in Poland. The increase of PM₁₀ was mainly driven by increases in PM_2.5; PM_10−2.5 concentrations changed only marginally or even decreased. Overall, the results indicate high levels of particulate air pollution in Central and Eastern Europe with large changes between seasons, likely caused by local heating.     

Field performance of dichotomous sequential PM air samplers

For over one year, the Environmental Protection Commission of Hillsborough County (EPCHC) in Tampa, Florida, operated two dichotomous sequential particulate matter air samplers collocated with a manual Federal Reference Method (FRM) air sampler at a waterfront site on Tampa Bay. The FRM was alternately configured as a PM_2.5, then as a PM₁₀ sampler. For the dichotomous sampler measurements, daily 24-h integrated PM_2.5 and PM_10–2.5 ambient air samples were collected at a total flow rate of 16.7 l min⁻¹. A virtual impactor split the air into flow rates of 1.67 and 15.0 l min⁻¹ onto PM_10–2.5 and PM_2.5 47-mm diameter PTFE^® filters, respectively. Between the two dichotomous air samplers, the average concentration, relative bias and relative precision were 13.3 μg m⁻³, 0.02% and 5.2% for PM_2.5 concentrations (n=282), and 12.3 μg m⁻³, 3.9% and 7.7% for PM_10–2.5 concentrations (n=282). FRM measurements were alternate day 24-h integrated PM_2.5 or PM₁₀ ambient air samples collected onto 47-mm diameter PTFE^® filters at a flow rate of 16.7 l min⁻¹. Between a dichotomous and a PM_2.5 FRM air sampler, the average concentration, relative bias and relative precision were 12.4 μg m⁻³, −5.6% and 8.2% (n=43); and between a dichotomous and a PM₁₀ FRM air sampler, the average concentration, relative bias and relative precision were 25.7 μg m⁻³, −4.0% and 5.8% (n=102). The PM_2.5 concentration measurement standard errors were 0.95, 0.79 and 1.02 μg m⁻³; for PM₁₀ the standard errors were 1.06, 1.59, and 1.70 μg m⁻³ for two dichotomous and one FRM samplers, respectively, which indicate the dichotomous samplers have superior technical merit. These results reveal the potential for the dichotomous sequential air sampler to replace the combination of the PM_2.5 and PM₁₀ FRM air samplers, offering the capability of making simultaneous, self-consistent determinations of these particulate matter fractions in a routine ambient monitoring mode.     

Characteristics of vertical profiles and sources of PM2.5, PM10 and carbonaceous species in Beijing

In August 2003 during the anticipated month of the 2008 Beijing Summer Olympic Games, we simultaneously collected PM₁₀ and PM_2.5 samples at 8, 100, 200 and 325 m heights up a meteorological tower and in an urban and a suburban site in Beijing. The samples were analysed for organic carbon (OC) and elemental carbon (EC) contents. Particulate matter (PM) and carbonaceous species pollution in the Beijing region were serious and widespread with 86% of PM_2.5 samples exceeding the daily National Ambient Air Quality Standard of the USA (65 μg m⁻³) and the overall daily average PM₁₀ concentrations of the three surface sites exceeding the Class II National Air Quality Standard of China (150 μg m⁻³). The maximum daily PM_2.5 and PM₁₀ concentrations reached 178.7 and 368.1 μg m⁻³, respectively, while those of OC and EC reached 22.2 and 9.1 μg m⁻³ in PM_2.5 and 30.0 and 13.0 μg m⁻³ in PM₁₀, respectively. PM, especially PM_2.5, OC and EC showed complex vertical distributions and distinct layered structures up the meteorological tower with elevated levels extending to the 100, 200 and 300 m heights. Meteorological evidence suggested that there exist fine atmospheric layers over urban Beijing. These layers were featured by strong temperature inversions close to the surface (<50 m) and more stable conditions aloft. They enhanced the accumulation of pollutants and probably caused the complex vertical distributions of PM and carbonaceous species over urban Beijing. The built-up of PM was accompanied by transport of industrial emissions from the southwest direction of the city. Emissions from road traffic and construction activities as well as secondary organic carbon (SOC) are important sources of PM. High OC/EC ratios (range of 1.8–5.1 for PM_2.5 and 2.0–4.3 for PM₁₀) were found, especially in the higher levels of the meteorological tower suggesting there were substantial productions of SOC in summer Beijing. SOC is estimated to account for at least 33.8% and 28.1% of OC in PM_2.5 and PM₁₀, respectively, with higher percentages at the higher levels of the tower.     

Associations between particle physicochemical characteristics and oxidative capacity: An indoor PM10 study in Beijing,China

A study was undertaken to determine the use of a plasmid DNA scission assay to evaluate the causal relationships between particle oxidative capacity and physico-chemistry. Field emission scanning electron microscopy (FESEM), image analysis (IA) and inductively coupled plasma-mass spectrometry (ICP-MS) were employed to investigate the physico-chemical characteristics of indoor PM₁₀ (particulate matter with an aerodynamic diameter of 10 μm or less) in Beijing, China. Six PM₁₀ samples (indoor smoker's living room; indoor non-smoker's living room and kitchen; and outdoor Beijing city; winter versus summer) were selected to represent typical indoor Beijing PM₁₀ environments that contain high particle mass. The PM₁₀ collected from a kitchen and two smoker's homes had the lowest TD₅₀ (toxic dosage of PM₁₀ causing 50% plasmid DNA damage), being as low as 45 μg ml⁻¹ (kitchen) and 100 μg ml⁻¹ (living room), which suggests a high oxidative capacity, with the PM₁₀ generated in kitchens appearing to be the most toxic. The indoor PM₁₀ from the non-smoker's home and outdoor PM₁₀ samples demonstrated high TD₅₀ values and were deemed less bioreactive (i.e. caused limited DNA damage). FESEM observations revealed that four types of particle species were prevalent in Beijing indoor PM₁₀; soot aggregates, minerals, coal fly ash and unknown fine particles. IA showed that higher percentages of soot and unknown fine particles were associated with the lower TD₅₀ values, suggesting that soot and the unknown fine particles may be important components responsible for the observed plasmid DNA damage. The water-soluble trace elements were negatively correlated with the TD₅₀ values, implying that the DNA damage may be attributed to the water-soluble fraction of the PM₁₀. Water-soluble zinc revealed the best relationship with the TD₅₀ values than other analyzed elements, signifying it may play a role in driving the oxidative damage.     

Characterization of PM2.5-bound polycyclic aromatic hydrocarbons in Atlanta

Twenty-four hour PM_2.5 samples from a rural site, an urban site, and a suburban site (next to a major highway) in the metropolitan Atlanta area in December 2003 and June 2004 were analyzed for 19 polycyclic aromatic hydrocarbons (PAH). Extraction of the air samples was conducted using an accelerated solvent extraction method followed by isotope dilution gas chromatography/mass spectrometry determination. Distinct seasonal variations were observed in total PAH concentration (i.e. significantly higher concentrations in December than in June). Mean concentrations for total particulate PAHs in December were 3.16, 4.13, and 3.40 ng m^?3 for the urban, suburban and rural sites, respectively, compared with 0.60, 0.74, and 0.24 ng m^?3 in June. Overall, the suburban site, which is impacted by a nearby major highway, had higher PAH concentration than did the urban site. Total PAH concentrations were found to be well correlated with PM_2.5, organic carbon (OC), and elemental carbon (EC) in both months (r² = 0.36–0.78, p < 0.05), although the slopes from the two months were different. PAHs represented on average 0.006% of total PM_2.5 mass and 0.017% of OC in June, compared with 0.033% of total PM_2.5 and 0.14% of OC in December. Total PAH concentrations were also correlated with potassium ion (r² = 0.39, p = 0.014) in December, but not in June, suggesting that in winter biomass burning can potentially be an important source for particulate PAH. Retene was found at a higher median air concentration at the rural site than at the urban and suburban sites—unlike the rest of the PAHs, which were found at lower levels at the rural site. Retene also had a larger seasonal difference and had the weakest correlation with the rest of the PAHs measured, suggesting that retene, in particular, might be associated with biomass burning.     

Chemical characteristics of principal PM2.5 species in Chongju,South Korea

Fine particles were collected over four seasons from October 1995 to August 1996 to evaluate the chemical characteristics of principal PM_2.5 components in Chongju, South Korea. The annual mean concentrations of PM_2.5 (d_p⩽2.5 μm), sulfate, nitrate, ammonium, elemental carbon (EC) and organic carbon (OC) were 44.2, 8.22, 3.63, 2.84, 4.44 and 4.99 μg m⁻³, respectively. The sum of the species measured from this study accounted for 50–62% of the PM_2.5 mass. Sulfate was the most abundant species and constituted 13–23% of the PM_2.5 mass. The EC and OC accounted for 17–28% of PM_2.5. The correlation between OC and EC was strong, and the annual mean ratio of OC/EC was 1.12, suggesting that OC measured in the Chongju area may be emitted directly in particulate form as a primary aerosol.     

Characterisation of fresh particulate vehicular exhausts near a Paris high flow road

Simultaneous continuous measurements of PM_2.5, PM₁₀, black carbon mass (BCae), Black smoke (BS) and particle number density (N) were conducted in the close vicinity of a high traffic road around Paris during a three-month period beginning in August 1997. In parallel some aerosol collection was performed on filters in order to assess the black carbon (BC), organic carbon (OC) and water soluble organic fractions (WSOC) of the freshly emitted traffic aerosols. The high hourly concentrations of PM_2.5 (39±20 μg m⁻³), BCae (14±7 μg m⁻³), and N (220,000±115,000 cm⁻³), were found to be well correlated with each other. On average PM_2.5 represented 66±13% of PM₁₀ and appears to be composed primarily of BC (43±20%). On the contrary no correlation was found between PM_2.5 and the coarse (PM₁₀–PM_2.5) mass fractions which was attributed to resuspension processes by vehicles. Black carbon mass concentrations obtained from both filter analyses (BC) and Aethalometre data (BCae) show a good agreement suggesting that the Aethalometre calibration based on a black carbon specific attenuation coefficient (σ) of 19 m² g⁻¹ is well adapted to nearby roadside measurements. Daily BC (used as a surrogate for fine particles) concentrations and wind speed were found to be anti-correlated. Average daily variations of BC could be related to traffic intensity and regime as well as to the boundary layer height. As expected for freshly emitted traffic aerosols, filter analyses indicated a high BC/TC ratio (29±5%) and a low mean WSOC/OC ratio (12.5±5%) for the bulk aerosol. For these two ratios no day/night differences were observed, the sampling station being probably too close to traffic to evidence photochemical modification of the aerosol phase. Finally, a linear relationship was found between BC and BS hourly concentrations (BC=0.10×BS+1.18; r²=0.93) which offers interesting perspectives to retrieve BC concentrations from existing BS archives.     

Airborne particle PM2.5/PM10 mass distribution and particle-bound PAH concentrations near a medical waste incinerator

This study attempts to determine the influence of air quality in a residential area near a medical waste incineration plant. Ambient air concentrations of polycyclic aromatic hydrocarbons (PAHs), PM₁₀ and PM_2.5 (PM—particulate matter) were determined by collecting air samples in areas both upwind and downwind of the plant. The differences in air pollutant levels between the study area and a reference area 11 km away from the plant were evaluated.Dichotomous samplers were used for sampling PM_2.5 and PM₁₀ from ambient air. Two hundred and twenty samples were obtained from the study area, and 100 samples were taken from a reference area. Samples were weighed by an electronic microbalance and concentrations of PM_2.5 and PM₁₀ were determined. A HPLC equipped with a fluorescence detector was employed to analyze the concentrations of 15 PAHs compounds adsorbed into PM_2.5 and PM₁₀.The experimental results indicated that the average concentrations of PM_2.5 and PM₁₀ were 30.34±17.95 and 36.81±20.45 μg m⁻³, respectively, in the study area, while the average ratio of PM_2.5/PM₁₀ was 0.82±0.01. The concentrations of PM_2.5 and PM₁₀ of the study area located downwind of the incinerator were significantly higher than the study area upwind of the incinerator (P<0.05).The concentration of PAHs in PM_2.5 in the study area was 2.2 times higher than in the reference area (P<0.05). Furthermore, the benzo(a)pyrene concentrations in PM_2.5 and PM₁₀ were 0.11±0.05 ng m⁻³ and 0.12±0.06 ng m⁻³ in the study area, respectively. The benzo(a)pyrene concentrations of PM_2.5 and PM₁₀ in the study area were 7 and 5.3 times higher than in the reference area (P<0.05), respectively.The study indicated that the air quality of PM_2.5, PM₁₀ and PAHs had significant contamination by air pollutants emitted from a medical waste incineration factory, representing a public health problem for nearby residences, despite the factory being equipped with a modern air pollution control system.     

Characteristics of the major chemical constituents of PM2.5 and smog events in Seoul,Korea in 2003 and 2004

One hundred ninety-five chemically speciated samples were collected from March 2003 to February 2005 in the Seoul Metropolitan area to investigate the characteristics of the major components in PM_2.5 and to characterize the chemical variations between smog and non-smog events. The annual average PM_2.5 concentration was 43 μg m⁻³ that is almost three times higher than the US NAAQS annual PM_2.5 standard of 15 μg m⁻³. During this sampling period, smog and yellow sand events were observed on 27 and 10 days, respectively. The PM_2.5 concentrations and its constituents during smog events were about two–three times higher than those during non-smog and yellow sand events. In particular, the mass fractions of secondary aerosols such as sulfate, nitrate, and ammonium during the smog events were higher than those of the other constituents. The mean concentration and mass fraction of secondary organic carbon (SOC) were highest during the winter smog events. Sulfate, nitrate and SOC that can have long residence times were important species during the smog events suggesting that regional scale sources rather than local sources were important. Five-day backward air trajectory analysis showed that the air parcels during smog events passed through the major industrial areas in China more often than those during non-smog events.     

Quantifying the effect of urban tree planting on concentrations and depositions of PM10 in two UK conurbations

Trees are efficient scavengers of particulate matter and are characterised by higher rates of dry deposition than other land types. To estimate the potential of urban tree planting for the mitigation of urban PM₁₀ concentrations, an atmospheric transport model was used to simulate the transport and deposition of PM₁₀ across two UK conurbations (the West Midlands and Glasgow). Tree planting was simulated by modifying the land cover database, using GIS techniques and field surveys to estimate reasonable planting potentials. The model predicts that increasing total tree cover in West Midlands from 3.7% to 16.5% reduces average primary PM₁₀ concentrations by 10% from 2.3 to 2.1 μg m⁻³ removing 110 ton per year of primary PM₁₀ from the atmosphere. Increasing tree cover of the West Midlands to a theoretical maximum of 54% by planting all available green space would reduce the average PM₁₀ concentration by 26%, removing 200 ton of primary PM₁₀ per year. Similarly, for Glasgow, increasing tree cover from 3.6% to 8% reduces primary PM₁₀ concentrations by 2%, removing 4 ton of primary PM₁₀ per year. Increasing tree cover to 21% would reduce primary PM₁₀ air concentrations by 7%, removing 13 ton of primary PM₁₀ per year.     

Seasonal and spatial trends in the sources of fine particle organic carbon in Israel,Jordan, and Palestine

A study of carbonaceous particulate matter (PM) was conducted in the Middle East at sites in Israel, Jordan, and Palestine. The sources and seasonal variation of organic carbon, as well as the contribution to fine aerosol (PM_2.5) mass, were determined. Of the 11 sites studied, Nablus had the highest contribution of organic carbon (OC), 29%, and elemental carbon (EC), 19%, to total PM_2.5 mass. The lowest concentrations of PM_2.5 mass, OC, and EC were measured at southern desert sites, located in Aqaba, Eilat, and Rachma. The OC contribution to PM_2.5 mass at these sites ranged between 9.4% and 16%, with mean annual PM_2.5 mass concentrations ranging from 21 to 25 ug m^?3. These sites were also observed to have the highest OC to EC ratios (4.1–5.0), indicative of smaller contributions from primary combustion sources and/or a higher contribution of secondary organic aerosol. Biomass burning and vehicular emissions were found to be important sources of carbonaceous PM in this region at the non-southern desert sites, which together accounted for 30%–55% of the fine particle organic carbon at these sites. The fraction of measured OC unapportioned to primary sources (1.4 μgC m^?3 to 4.9 μgC m^?3; 30%–74%), which has been shown to be largely from secondary organic aerosol, is relatively constant at the sites examined in this study. This suggests that secondary organic aerosol is important in the Middle East during all seasons of the year.     

Factors influencing PM10 emissions from road pavement wear

Accelerated pavement wear is one of the major environmental disadvantages of studded tyres in northern regions and results in increased levels of PM₁₀. Measurements of PM₁₀ in a road simulator hall have been used to study the influence of pavement properties, tyre type and vehicle speed on pavement wear. The test set-up included three different pavements (one granite and two quartzite with different aggregate sizes), three different tyre types (studded, non-studded, and summer tyres) and different speeds (30–70 km h^?1). The results show that the granite pavement was more prone to PM₁₀ production compared to the quartzite pavements. Studded winter tyres yield tens of times higher PM₁₀ concentrations compared to non-studded winter tyres. Wear from summer tyres was negligible in comparison. It was also shown that wear is strongly dependent on speed; every 10 km h^?1 increase yielded an increase of the PM₁₀ concentration of 680 μg m^?3 in one of the simulator experiments.     

Mass levels,crustal component and trace elements in PM10 in Palermo,Italy

Results concerning the levels and elemental compositions of daily PM₁₀ samples collected at four air quality monitoring sites in Palermo (Italy) are presented. The highest mean value of PM₁₀ concentrations (46 μg m⁻³, with a peak value of 158 μg m⁻³) was recorded at the Di Blasi urban station, and the lowest at Boccadifalco station (25 μg m⁻³), considered as a sub-urban background station. Seventeen elements (Al, As, Ba, Co, Cr, Cu, Fe, Li, Mn, Mo, Ni, Pb, Sb, Sr, U, V, Zn) were measured by ICP-MS. Al and Fe showed the highest concentrations, indicating the significant contribution of soil and resuspended mineral particles to atmospheric PM₁₀. Ba, Cr, Cu, Mn, Mo, Ni, Pb, Sb, V and Zn had higher concentrations at the three urban sampling sites than at the sub-urban background station. Besides soil-derived particles, an R-mode cluster analysis revealed a group of elements, Mo, Cu, Cr, Sb and Zn, probably related to non-exhaust vehicle emission, and another group, consisting of Ba, As and Ni, which seemed to be associated both with exhaust emissions from road traffic, and other combustion processes such as incinerators or domestic heating plants. The results also suggest that Sb, or the association Sb–Cu–Mo, offers a way of tracing road traffic emissions.     

Secondary aerosol formation through photochemical reactions estimated by using air quality monitoring data in Taipei City from 1994 to 2003

Analyses of diurnal patterns of PM₁₀ in Taipei City have been performed in this study at different daily ozone maximum concentrations (O_3,max) from 1994 to 2003. In order to evaluate secondary aerosol formation at different ozone levels, CO was used as a tracer of primary aerosol, and O_3,max was used as an index of photochemical activity. Results show that when O_3,max exceeds 120 ppb, the highest photochemical formation of secondary aerosol can be found at 15:00 (local time). The produced secondary aerosol is estimated to contribute 30 μg m⁻³ (43%) of PM₁₀ concentration, and about 77% of the estimated secondary PM₁₀ is composed of PM_2.5. The estimated maximum concentration of secondary aerosol occurs 2–3 h later than the maximum ozone concentration. As revealed in an O₃ episode, PM₁₀ and PM_2.5 vary consistently with O₃ at daytime, which suggests that they are mostly secondary aerosols produced from photochemical reactions. Data collected from Taipei aerosol supersite in 2002 indicates that for all O₃ levels, summertime PM_2.5 is composed of 23%, 20%, 9%, and 7% of organic carbon, sulfate, nitrate, and elemental carbon, respectively. Aerosol number and volume size spectra are dominated by submicron particles either from pollution transport or photochemical reactions. Secondary PM₁₀ concentrations show increasing tendencies for the time between 15:00 and 19:00 from 1994–1996 to 2001–2003. This reveals that the abatement of secondary PM₁₀ becomes more important after pronounced primary PM₁₀ reduction in a metropolis.     

A consistent method for modelling PM10 and PM2.5 concentrations across the United Kingdom in 2004 for air quality assessment

A modelling method has been developed to map PM₁₀ and PM_2.5 concentrations across the UK at background and roadside locations. Separate models have been calibrated using gravimetric measurements and Tapered Element Oscillating Microbalance instruments (TEOM) using source apportionments appropriate to the size fractions and sampling methods. Maps have been prepared for a base year of 2004 and predictions have been calculated for 2010 and 2020 on the basis of current policies. Comparisons of the modelling results with air quality regulations suggest that exceedences of the EU Daughter Directive stage 1 24-h limit value for PM₁₀ at the roadside in 2004 will be largely eliminated by 2020. The concentration cap of 25 μg m⁻³ for PM_2.5 proposed within the CAFÉ Directive is expected to be met at all locations. Projections for 2010 and 2020 suggest that the proposed exposure reduction (ER) target is likely to be considerably more stringent and require additional measures beyond current policies. Thus the model results suggest that the balance between the stringency of the concentration cap and the ER target in the proposed directive is appropriate. Measures to achieve greater reductions should therefore have the maximum public health benefit and air quality policy is not driven by the need to reduce concentrations at isolated ‘hotspots’.     

Multi-year hourly PM2.5 carbon measurements in New York: Diurnal,day of week and seasonal patterns

Multi-year hourly measurements of PM_2.5 elemental carbon (EC) and organic carbon (OC) from a site in the South Bronx, New York were used to examine diurnal, day of week and seasonal patterns. The hourly carbon measurements also provided temporally resolved information on sporadic EC spikes observed predominantly in winter. Furthermore, hourly EC and OC data were used to provide information on secondary organic aerosol formation. Average monthly EC concentrations ranged from 0.5 to 1.4 μg m^?3 with peak hourly values of several μg m^?3 typically observed from November to March. Mean EC concentrations were lower on weekends (approximately 27% lower on Saturday and 38% lower on Sunday) than on weekdays (Monday to Friday). The weekday/weekend difference was more pronounced during summer months and less noticeable during winter. Throughout the year EC exhibited a similar diurnal pattern to NO_x showing a pronounced peak during the morning commute period (7–10 AM EST). These patterns suggest that EC was impacted by local mobile emissions and in addition by emissions from space heating sources during winter months. Although EC was highly correlated with black carbon (BC) there was a pronounced seasonal BC/EC gradient with summer BC concentrations approximately a factor of 2 higher than EC. Average monthly OC concentrations ranged from 1.0 to 4.1 μg m^?3 with maximum hourly concentrations of 7–11 μg m^?3 predominantly in summer or winter months. OC concentrations generally correlated with PM_2.5 total mass and aerosol sulfate and with NO_x during winter months. OC showed no particular day of week pattern. The OC diurnal pattern was typically different than EC except in winter when OC tracked EC and NO_x indicating local primary emissions contributed significantly to OC during winter at the urban location. On average secondary organic aerosol was estimated to account for 40–50% of OC during winter and up to 63–73% during summer months.     

What are the sources and conditions responsible for exceedences of the 24 h PM10 limit value (50 μg m−3) at a heavily trafficked London site?

The European Union has set limit values for PM₁₀ to be met in 2005. At Marylebone Road, London, where the traffic is heavy, the daily limit value of 50 μg m⁻³ is exceeded more than 35 times a year. A total of 185 days with daily PM₁₀ concentrations exceeding the limit value of 50 μg m⁻³ measured between January 2002 and December 2004 (data capture of 89.5%) are discussed in this paper. These exceedences were more frequent in early spring and in autumn. Concentrations have been disaggregated into regional, urban (background) and local (street) contributions. Most of the episodes of gravimetric PM₁₀ above the limit value were associated with a high regional background and very often the regional contribution dominated the PM₁₀ mass. The secondary aerosol (especially the particulate nitrate) made a major contribution to the PM₁₀ load. These situations were frequently observed when air masses came from the European mainland (showing that both emissions from the UK and other EU countries contributed to the exceedences), and less frequently with maritime air masses that have stagnated over the UK (showing that emissions from the UK alone less frequently contributed to the high regional background). However, the higher frequency of episodes breaching the limit value at the roadside site than at the rural site and the higher frequency of PM₁₀ concentrations above the limit value on weekdays show that the high regional contributions are additional to local and urban emissions. Local emissions mainly due to traffic were the second important contributor to the exceedences, while the contribution of the urban background of London was less important than the local emissions and the regional background. Applying the pragmatic mass closure model of Harrison et al. [2003. A pragmatic mass closure model for airborne particulate matter at urban background and roadside sites. Atmospheric Environment 37, 4927–4933], revealed that the regional aerosol is comprised very largely of ammonium nitrate and sulphate and secondary organic aerosol. Findings suggest that international abatement of secondary aerosol precursors may be the most effective measure to fulfil the requirements of the European Directive 1999/30/CE by lowering the regional background.