Photochemical modeling in California with two chemical mechanisms: model intercomparison and response to emission reductions

An updated version of the Statewide Air Pollution Research Center (SAPRC) chemical mechanism (SAPRC07C) was implemented into the Community Multiscale Air Quality (CMAQ) version 4.6. CMAQ simulations using SAPRC07C and the previously released version, SAPRC99, were performed and compared for an episode during July-August, 2000. Ozone (O3) predictions of the SAPRC07C simulation are generally lower than those of the SAPRC99 simulation in the key areas of central and southern California, especially in areas where modeled concentrations are greater than the federal 8-hr O3 standard of 75 parts per billion (ppb) and/or when the volatile organic compound (VOC)/nitrogen oxides (NOx) ratio is less than 13. The relative changes of ozone production efficiency (OPE) against the VOC/NOx ratio at 46 sites indicate that the OPE is reduced in SAPRC07C compared with SAPRC99 at most sites by as much as approximately 22%. The SAPRC99 and SAPRC07C mechanisms respond similarly to 20% reductions in anthropogenic VOC emissions. The response of the mechanisms to 20% NOx emissions reductions can be grouped into three cases. In case 1, in which both mechanisms show a decrease in daily maximum 8-hr O3 concentration with decreasing NOx emissions, the O3 decrease in SAPRC07C is smaller. In case 2, in which both mechanisms show an increase in O3 with decreasing NOx emissions, the O3 increase is larger in SAPRC07C. In case 3, SAPRC07C simulates an increase in O3 in response to reduced NOx emissions whereas SAPRC99 simulates a decrease in O3 for the same region. As a result, the areas where NOx controls would be disbeneficial are spatially expanded in SAPRC07C. Although the results presented here are valuable for understanding differences in predictions and model response for SAPRC99 and SAPRC07C, the study did not evaluate the impact of mechanism differences in the context of the U.S. Environmental Protection Agency's guidance for using numerical models in demonstrating air quality attainment. Therefore, additional study is required to evaluate the full regulatory implications of upgrading air quality models to SAPRC07.     

Atmospheric pollution transport: the parallelization of a transport & chemistry code

We discuss a model for computing the chemical reactions occurring among air pollutants and predict their dispersion in the atmosphere. We consider a parallel implementation on a CRAY T3D, using up to 128 processors. A regular subdomain decomposition is considered to optimize inter-processor communications, while load balancing – the main technical difficulty to obtain a good efficiency – is achieved by re-assigning temporarily pieces of work to other processors, according to a global strategy. The performance of our implementation is described by an analytical relation whose validity is checked on realistic data sets. A speedup of 100 is obtained with 128 processors.     

Development and application of a regional-scale atmospheric mercury model based on WRF/Chem: a Mediterranean area investigation

The emission, transport, deposition and eventual fate of mercury (Hg) in the Mediterranean area has been studied using a modified version of the Weather Research and Forecasting model coupled with Chemistry (WRF/Chem). This model version has been developed specifically with the aim to simulate the atmospheric processes determining atmospheric Hg emissions, concentrations and deposition online at high spatial resolution. For this purpose, the gas phase chemistry of Hg and a parametrised representation of atmospheric Hg aqueous chemistry have been added to the regional acid deposition model version 2 chemical mechanism in WRF/Chem. Anthropogenic mercury emissions from the Arctic Monitoring and Assessment Programme included in the emissions preprocessor, mercury evasion from the sea surface and Hg released from biomass burning have also been included. Dry and wet deposition processes for Hg have been implemented. The model has been tested for the whole of 2009 using measurements of total gaseous mercury from the European Monitoring and Evaluation Programme monitoring network. Speciated measurement data of atmospheric elemental Hg, gaseous oxidised Hg and Hg associated with particulate matter, from a Mediterranean oceanographic campaign (June 2009), has permitted the model’s ability to simulate the atmospheric redox chemistry of Hg to be assessed. The model results highlight the importance of both the boundary conditions employed and the accuracy of the mercury speciation in the emission database. The model has permitted the reevaluation of the deposition to, and the emission from, the Mediterranean Sea. In light of the well-known high concentrations of methylmercury in a number of Mediterranean fish species, this information is important in establishing the mass balance of Hg for the Mediterranean Sea. The model results support the idea that the Mediterranean Sea is a net source of Hg to the atmosphere and suggest that the net flux is ≈30 Mg year^?1 of elemental Hg.     

Validated sampling strategy for assessing contaminants in soil stockpiles

Dutch legislation on the reuse of soil requires a sampling strategy to determine the degree of contamination. This sampling strategy was developed in three stages. Its main aim is to obtain a single analytical result, representative of the true mean concentration of the soil stockpile. The development process started with an investigation into how sample pre-treatment could be used to obtain representative results from composite samples of heterogeneous soil stockpiles. Combining a large number of random increments allows stockpile heterogeneity to be fully represented in the sample. The resulting pre-treatment method was then combined with a theoretical approach to determine the necessary number of increments per composite sample. At the second stage, the sampling strategy was evaluated using computerised models of contaminant heterogeneity in soil stockpiles. The now theoretically based sampling strategy was implemented by the Netherlands Centre for Soil Treatment in 1995. It was applied to all types of soil stockpiles, ranging from clean to heavily contaminated, over a period of four years. This resulted in a database containing the analytical results of 2570 soil stockpiles. At the final stage these results were used for a thorough validation of the sampling strategy. It was concluded that the model approach has indeed resulted in a sampling strategy that achieves analytical results representative of the mean concentration of soil stockpiles.     

Impacts of ozone on the growth and yield of field-grown winter wheat

Seed of winter wheat (Triticum aestivum L. cv Riband) was sown on 29 August 1992 in eight field plots. Four plots were exposed to elevated ozone (O(3)) concentrations on 16 days between 29 August and 2 October 1992, for 6 h day(-1), and on 27 days between 29 March and 24 August 1993, for 7 h day(-1). Mean daily O(3) concentrations were approximately 30 and 80 nmol mol(-1) in ambient and fumigated plots, respectively. Plants were sampled on 5 November (1992), 14 January, 16 February, 1 April, 25 May, 23 June and 24 August (1993). No visible symptoms of O(3) damage or premature senescence were observed at any time over the course of the experiment. Exposure to elevated O(3) decreased the above ground biomass by reducing plant density and individual plant relative growth rate. However, there was no significant influence of the pollutant on the growth of the root relative to the shoot. Assessment of yield characteristics at the final harvest revealed an O(3)-induced decrease in the number of grains per ear, as a result of fewer grains per spikelet and an increase in the number of infertile florets per spikelet. No significant effects of the pollutant on the number of ears per plant, spikelets per ear, or 1000 grain weight were found. As a result of the combined effects on the number of grains per ear and the decrease in plant density and growth rate, O(3) exposure reduced grain and straw yields (tonnes ha(-1)) by 13 and 8%, respectively. However, no significant change in the partitioning of dry matter between the grain and the straw was observed in fumigated plots. The findings are discussed within the context of United Nation Economic Commission for Europe critical level guidelines for the protection of crop yields, in relation to their application to winter-sown crops.     

The effects of coal-smoke pollutants on the growth, yield and leaf epidermal features of Abelmoschus esculentus moench

In Abelmoschus esculentus var. Pusa Sawani, coal-smoke pollutants, experienced close to a thermal power plant, led to decreases of plant height and stem diameter, jeopardised the production of leaves and flower buds and stimulated leaf and flower fall, leading to a decrease in the number of fruits set per plant. The length of fruits was affected a little, and the circumference and fresh weight suffered significantly, causing a decrease in plant yield. The net productivity of stems, roots and leaves incurred losses of 22.5%, 24.0% and 37.5%, respectively, and resulted in a 28.3% loss in the total net productivity of polluted plants. A decrease in stomatal density, aperture and index, and a lower density of epidermal cells of greater dimensions were observed on both the leaf surfaces. Abnormalities of the stomatal complexes were also observed on the upper surface of polluted leaves.     

玻璃注射器对顶空气相色谱法分析苯系物的误差原因分析

按GB11890—89顶空气相色谱法分析苯系物时，发现重复性和分割水平样品平行性较差，经仔细分析，是由于使用普通玻璃注射器造成的。为避免此类误差，建议顶空气相色谱法分析时，使用带特氟龙顶端推杆的气密性注射器。     

经济发展,碳排放和经济演化

本文用计量经济学的方法通过对中国、日本、美国的时间序列分析和１９９０年的全球截面数据分析,探讨了经济增长与ＣＯ２排放的关系。并重点分析了人口增长、能源消费强度变化的人均碳排放的影响。分析表明从政策角度而言,人均碳排放与人均ＧＤＰ之间不存在Ｋｕｚｎｅｔｓ曲线。人口增长和人均ＧＤＰ的增加是人均碳排放增加的主要来源,而ＧＤＰ能源消费强度的下降则是碳排放减少的重要来源。     

Aerobic plate count,Salmonella and Campylobacter loads of whole bird carcass rinses from pre-chillers with different water management strategies in a commercial poultry processing plant

Abstract

Salmonella and Campylobacter are significant issues for poultry processors because of increasing regulatory standards as well as public health concerns. The goal of this study is to report the effects of two different pre-chiller systems that utilize different temperatures and water recirculation systems on whole bird carcass rinsates. Both pre-chiller tanks were contained within a single poultry processing facility and operated at different temperatures and water systems. The incidence of Campylobacter spp. and Salmonella spp., as well as the aerobic plate counts on whole bird carcass rinses are reported in this study from each pre-chiller system. The results from this study reveal that there are significant differences in how microbial populations and pathogens change over time in each pre-chiller system. Furthermore, we identify that these patterns are different per system. Such data are impactful as it indicates that measuring carcasses within a plant must consider both temperature and water recirculation as it may prevent comparability of different lines within a single processing facility.     

Sampling and Analysis of Volatile Organic Compounds Evolved During Thermal Processing of Acrylonitrile Butadiene Styrene Composite Resins

Abstract

The evaluation of emissions of volatile organic compounds (VOCs) during processing of resins is of interest to resin manufacturers and resin processors. An accurate estimate of the VOCs emitted from resin processing has been difficult due to the wide variation in processing facilities. This study was designed to estimate the emissions in terms of mass of emitted VOC per mass of resin processed.

A collection and analysis method was developed and validated for the determination of VOCs present in the emissions of thermally processed acrylonitrile butadiene styrene (ABS) resins. Four composite resins were blended from automotive, general molding, pipe, and refrigeration grade ABS resins obtained from the manufacturers. Emission samples were collected in evacuated 6-L Summa canisters and then analyzed using gas chromatography/flame ionization detection/mass selective detection (GC/FID/MSD). Levels were determined for nine target analytes detected in canister samples, and for total VOCs detected by an inline GC/FID. The emissions evolved from the extrusion of each composite resin were expressed in terms of mass of VOCs per mass of processed resin. Styrene was the principal volatile emission from all the composite resins. VOCs analyzed from the pipe resin sample contained the highest level of styrene at 402 μg/g. An additional collection and detection method was used to determine the presence of aerosols in the emissions. This method involved collecting particulates on glass fiber filters, extracting them with solvents, and analyzing them using gas chromatography/mass spectrometry (GC/MS). No significant levels of any of the target analytes were detected on the filters.     

Development of emission factors for polyamide processing

Emission factors for selected volatile organic compounds (VOCs) and particulate material were developed during processing of commercial grades of polyamide 6, polyamide 66, and polyamide 66/6 resins. A small commercial-type extruder was used, and melt temperatures ranged from 475 to 550 degrees F. An emission factor was calculated for each substance measured and is reported as pounds released to the atmosphere per million pounds of polymer resin processed. Scaled to production volumes, these emission factors can be used by processors to estimate emission quantities from similar polyamide extrusion operations.     

Influence of particle location on the number of charges per charged nanoparticle at the outlet of a needle charger

This study has investigated numerically the influence of particle location on the number of charges per charged particle in the 10–40 nm size range at the outlet of a needle charger by simulating flow field, electric field, particle charging, and particle trajectory at various conditions. The results show that the total (i.e., diffusion + field charging) number of charges per particle increase with decreasing ratio values of radial location at the outlet of the charger due to the particle position close to the needle tip. It has also been shown that in the outlet region of the charger there is a critical radial location at which the number of charges per particle is a maximum; this critical radial location represents the point at which the charged particle trajectory becomes closest to the needle electrode. The maximum value of number of charges increases with increasing Reynolds number and slightly increases with decreasing applied voltage for particle diameter larger than 20 nm. The maximum number of charges per charged nanoparticle increases with increasing particle diameter. In addition, the minimum ratio value of radial particle location decreases with increasing Reynolds number for various particle diameters.

Implications: In this work, the influence of particle location on the number of charges per charged nanoparticle at the outlet of a needle charger has been investigated using numerical models under different conditions. The results demonstrate that the radial location affects the number of charges per particle at the outlet of the charger. The maximum number of charges increases with increasing particle diameter, and the minimum ratio value of radial particle location decreases with increasing Reynolds number. The numerical models explain and quantify the number of charges on the charged particle in the 10–40 nm size range from the outlet of the needle charger at various conditions.     

An assessment of the chronic toxicity of the synthetic pyrethroid, fenvalerate, to Daphnia galeata mendotae, using life tables

The effects of chronic exposure to fenvalerate, a synthetic pyrethroid insecticide, on the cladoceran Daphnia galeata mendotae were evaluated under laboratory conditions. The daphnids were exposed for their entire life cycle to concentrations ranging from 0.005 to 0.1 microg fenvalerate litre(-1). The parameters used to determined toxicity were survival, time to first reproduction, reproductive frequency, number of young per brood, cumulative brood size, intrinsic rate of natural increase (r(m)), generation time (T) and net reproductive rate (R(0)). A concentration of 0.005 microg fenvalerate litre(-1) resulted in an increase in longevity but a decrease in production of young. Higher concentrations caused a decrease in survival. Studies of shorter duration than the complete life cycle of the organisms would not have detected toxicity at such low levels. The intrinsic rate of natural increase, r(m), was not affected by fenvalerate until concentration reached 0.05 microg litre(-1) and r(m) decreased to 0.113 from 0.238. A concentration of 0.01 microg litre(-1) caused the net reproductive rate, R(0), and the generation time, T, to decrease to 73.2 offspring per female and 17.3 days from 125.9 offspring per female and 20.3 days, respectively.     

Development of Emission Factors for Polyamide Processing

ABSTRACT

Emission factors for selected volatile organic compounds (VOCs) and particulate material were developed during processing of commercial grades of polyamide 6, polyamide 66, and polyamide 66/6 resins. A small commercial-type extruder was used, and melt temperatures ranged from 475 to 550 °F. An emission factor was calculated for each substance measured and is reported as pounds released to the atmosphere per million pounds of polymer resin processed. Scaled to production volumes, these emission factors can be used by processors to estimate emission quantities from similar polyamide extrusion operations.     

No evidence for a critical salinity threshold for growth and reproduction in the freshwater snail Physa acuta

The growth and reproduction of the freshwater snail Physa acuta (Gastropoda: Physidae) were measured at various salinity levels (growth: distilled water, 50, 100, 500, 1000 and 5000 microS/cm; reproduction: deionized water, 100, 500, 1000 and 3000 microS/cm) established using the artificial sea salt, Ocean Nature. This was done to examine the assumption that there is no direct effect of salinity on freshwater animals until a threshold, beyond which sub-lethal effects, such as reduction in growth and reproduction, will occur. Growth of P. acuta was maximal in terms of live and dry mass at salinity levels 500-1000 microS/cm. The number of eggs produced per snail per day was maximal between 100 and 1000 microS/cm. Results show that rather than a threshold response to salinity, small rises in salinity (from low levels) can produce increased growth and reproduction until a maximum is reached. Beyond this salinity, further increases result in a decrease in growth and reproduction. Studies on the growth of freshwater invertebrates and fish have generally shown a similar lack of a threshold response. The implications for assessing the effects of salinisation on freshwater organisms need to be further considered.     

Improved spatial allocation methodology for on-road mobile emissions

Emissions from automobiles and trucks operating on public roads represent a major portion of the air pollutants included in emission inventories. When emission data are prepared for air quality modeling studies, such as those supporting development of a State Implementation Plan, an emission processor matches the spatial and temporal resolution of the emissions to the requirements of the modeling study. However, the spatial location of vehicular emissions is not known and must be estimated. This paper presents a methodology for determining the spatial distribution of the roads belonging to a road class using geospatial data functions, such as those commonly provided by a geographic information system. Vehicle-miles traveled (VMT) are then allocated to medium-resolution (12 x 12-km) and fine-resolution (4 x 4-km) modeling grids using both this methodology and the existing top-down methodology, which uses population density. The results show a significant difference in the spatial distribution of VMT between these two methodologies. Based upon these results, we recommend using the road class-specific methodology in lieu of the population methodology for spatially allocating vehicular emissions for medium- and finer-resolution modeling grids.     

The effects of crude and fuel oils on the growth, chlorophyll 'a' content and dry matter production of a green alga Scenedesmus quadricauda (Turp.) bréb

The growth of Scenedesmus quadricauda algae in a batch culture was examined in the presence of crude oil and fuel oil, added to the cultivation medium in the form of a water-soluble fraction (WSF), water extract (WE) and oil-water dispersion (OWD). On applying various concentrations of oils, a decrease in the number of cells, dry matter and chlorophyll 'a' production, with respect to the cell population, was observed. The extent of this decrease depended on the kind and concentration of the soluble and dispersed hydrocarbon fractions and on the proportions in which these occurred in the culture medium. On the other hand, the water extracts of both oils stimulated dry mass and chlorophyll 'a' content with respect to a single cell. This effect was accompanied by increased size of the algal cells. The WSF, WE and OWD of fuel oil, prepared from 200, 50 and 1 cm(3) of oil per dm(3) of BBM medium, respectively, had a similar inhibitory effect, which points to the dominant role of oil dispersion in the reduction of algal growth. Chemical analysis of the water extracts of fuel oil revealed the presence of 35 hydrocarbons of various kinds, mainly n-alkanes and polycyclic aromatic hydrocarbons.     

Assessing the Impacts of Establishing MPAs on Fishermen and Fish Merchants: The Case of Lyme Bay,UK

Shortly after the implementation of a marine protected area (MPA) in Lyme Bay in 2008, inside which scallop dredging and bottom trawling is prohibited, a socio-economic impact assessment was initiated. This article presents the initial findings from this study. The aim was to understand the costs and benefits to fishermen and fish merchants of establishing the MPA. These were assessed using a combination of primary and secondary data. The results indicate that the impacts of the closure differ according to the gear type and the fishing location used by the fishermen. Static gear fishermen who fish inside the closed area have seen changes in terms of increased fishing effort, mostly because they have been able to increase the number of crab and whelk pots they deploy. The effects of the closure on static gear fishermen who fish outside the closed area has been reported in terms of increased conflicts with towed gear fishermen who now fish regularly in their traditional grounds. Fishermen using towed gear on the other hand have been impacted through displacement effects as they have been forced to look for other fishing grounds outside the closed area. Most fish merchants and processors initially claimed that they were heavily impacted by the closure but when they were interviewed 1 year after the closure they suggested a more stable picture. Preliminary analyses of landings data indicate that the introduction of the MPA has so far had minimal impacts on the average incomes and financial profits of fishermen and fish merchants. This conclusion, however, reflects a short-term view as the impacts of the closure of Lyme Bay are likely to be felt for a long time to come.     

The mutagenicity of indoor air particles in a residential pilot field study: Application and evaluation of new methodologies

The mutagenicity of indoor air paniculate matter has been measured in a pilot field study of homes in Columbus, Ohio during the 1984 winter. The study was conducted in eight all natural-gas homes and two all electric homes. Paniculate matter and semi-volatile organic compounds were collected indoors using a medium volume sampler. A micro-forward mutation bioassay employing Salmonella typhimurium strain TM 677 was used to quantify the mutagenicity in solvent extracts of microgram quantities of indoor air particles. The mutagenicity was quantified in terms of both mutation frequency per mg of organic matter extracted and per cubic meter of air sampled. The combustion source variables explored in this study included woodburning in fireplaces and cigarette smoking. Homes in which cigarette smoking occurred had the highest concentrations of mutagenicity per cubic meter of air. The average indoor air mutagenicity per cubic meter was highly correlated with the number of cigarettes smoked. When the separate sampling periods in each room were compared, the mutagenicity in the kitchen samples was the most highly correlated with the number of cigarettes smoked.     

Effects of the organophosphate insecticide azinphos-methyl on the reproduction and cholinesterase activity of Biomphalaria glabrata

Azinphos-methyl is an organophosphate insecticide used for pest control on a number of food crops in many parts of the world. The snail Biomphalaria glabrata is a freshwater gastropod widely distributed in South America, Central America and Africa. The aim of the present work was to investigate whether azinphos-methyl causes alterations in the reproduction of B. glabrata. To this end, gastropod pigmented specimens were exposed to various concentrations of the insecticide (0.021, 0.5, 2.5, and 5 mg L⁻¹) for either 2 or 14 d. Along 14 d, several reproduction parameters and cholinesterase (ChE) activity were evaluated. In each group, the number of egg masses, the number of eggs per mass, the number of hatchings, the time to hatching, and the survival of the offspring after one month of treatment was evaluated. The results showed that, depending on the concentration and time of exposure, azinphos-methyl induced alterations in the reproduction of B. glabrata. These alterations were mainly represented by a decrease in the number of egg masses, and, in some cases, by a lower number or even the total absence of hatchings. Thus, the gastropods exposed to 2.5 and 5 mg L⁻¹ of azinphos-methyl for 14 d showed ChE inhibitions higher than 35% along time and completely lost their ability to reproduce. On the other hand, exposure to high acute concentrations or exposure to low concentrations for 14 d resulted in ChE inhibition equal to or lower than 35% between 7 and 14 d of treatment and similar alterations in reproduction. These were represented by a decrease in the number of egg masses. At low pestice levels, the number of egg masses and the number of offspring resulted to be more sensitive biomarkers than ChE inhibition. It is concluded that the insecticide azinphos-methyl can cause a decline in the reproductive performance of B. glabrata.