Haloacetic acid removal by sequential zero-valent iron reduction and biologically active carbon degradation

An innovative haloacetic acid (HAA) removal process was developed. The process consisted of a zero-valent iron (Fe⁰) column followed by a biologically active carbon (BAC) column that were efficient in degrading tri- and di-HAAs, and mono- and di-HAAs, respectively. The merit of the process was demonstrated by its performance in removing trichloroacetic acid (TCAA). An empty bed contact time of 10 min achieved nearly complete removal of 1.2 μM TCAA and its subsequent products, dichloroacetic acid (DCAA) and monochloroacetic acid (MCAA). HAA removal was a result of chemical dehalogenation and biodegradation rather than physical adsorption. Preliminary kinetic analyses were conducted and the pseudo-first-order rate constants were estimated at ambient conditions for Fe⁰ reduction of TCAA and biodegradation of DCAA and MCAA by BAC. This innovative process is highly promising in removing HAAs from drinking water, swimming pool water, and domestic or industrial wastewater.     

Novel insights in Al-MCM-41 precursor as adsorbent for regulated haloacetic acids and nitrate from water

High concentration of NO ₃ ^? in groundwater has raised concern over possible contamination of drinking water supplies. In addition, the formation of haloacetic acids (HAAs) as by-products during disinfection with chlorine-based agents is still a relevant issue, since HAAs pose serious health hazard. In this work, we investigated the affinity of a precursor of Al-MCM-41 (a mesostructured hexagonal aluminosilicate containing the template surfactant) towards nitrate and HAAs, for its possible application in the removal of these pollutants from natural and drinking waters. Additionally, adsorption kinetics and isotherms were studied. The adsorbent was synthesized using cetyltrimethylammonium bromide as surfactant and characterized by physico?Cchemical techniques. Simulated drinking water was spiked with the EPA-regulated HAAs (monochloroacetic (MCAA), monobromoacetic (MBAA), dichloroacetic (DCAA), dibromoacetic (DBAA), and trichloroacetic (TCAA) acids) and placed in contact with the adsorbent. The effect of matrix composition was studied. Adsorption kinetic studies were performed testing three kinetics models. For the adsorption studies, three adsorption isotherm approaches have been tested to experimental data. The pollutant recoveries were evaluated by suppressed ion chromatography. The affinity of the adsorbent was TCAA = DBAA = DCAA > MBAA > MCAA with DCAA, DBAA, and TCAA completely removed. A removal as high as 77?% was achieved for 13?mg/L nitrate. The adsorption isotherms of NO ₃ ^? and monochloroacetic acid can be modeled by the Freundlich equation, while their adsorption kinetics follow a pseudo-second-order rate mechanism. The adsorbent exhibited high affinity towards HAAs in simulated drinking water even at relevant matrix concentrations, suggesting its potential application for water remediation technologies.     

Formation of Disinfection Byproducts (DBPs) in Surface Water Sources: Differential Ultraviolet (UV) Absorbance Approach

Chlorination for drinking water forms various disinfection byproducts (DBPs) of trihalomethanes (THMs) and haloacetic acids (HAAs). Chlorination has been attributed to the destruction of activated aromatic sites of the natural organic matter (NOM) predominantly at electron rich sites. Experiments with Istanbul surface waters showed that the magnitude of the decrease in the ultraviolet (UV) absorbance at 272 nm (UV₂₇₂) was an excellent indicator of destruction of these sites by chlorine. The main objective of the present study is to develop the differential UV₂₇₂ absorbance (ΔUV₂₇₂) related models for the prediction of the formation of THM, HAA, and their species in raw water samples from Terkos, Buyukcekmece, and Omerli lakes under different chlorination conditions. Significant factors affecting DBP formation in the raw waters were identified through numerical and graphical techniques. The R² values of the models varied between 0.94 and 0.97, indicating excellent predictive ability for THM₄ and HAA₉ in the raw waters. The models were validated using additional data. The results of this study concluded that addition of ΔUV₂₇₂ parameter into THM₄ and HAA₉ models make the prediction of these DBP compounds more precisely than those of DBP models developed in the past. A better understanding of these modeling systems will help the water treatment plant operators to minimize the DBP formation, providing a healthier and better drinking water quality as well as identifying strategies to improve water treatment and disinfection processes.     

Electrochemical dechlorination of chloroacetic acids (CAAs) using hemoglobin-loaded carbon nanotube electrode

Hemoglobin (Hb) was immobilized on carbon nanotube (CNT) electrode to catalyze the dechlorination of chloroacetic acids (CAAs), and the electrocatalytic behaviors of the Hb-loaded electrode for the dechlorination of trichloroacetic acid (TCAA) were studied by cyclic voltammetry and constant-potential electrolysis technique. An Hb-loaded packed-bed flow reactor was also constructed for bioelectrocatalytic dechloriantion of CAAs from drinking water. The results showed that the reduced heme of Hb immobilized on CNT electrode was easily regenerated, and Hb exhibited a stable and high activity for reductive dechlorination of CAAs with significant lowering of overpotential. TCAA could be reduced at -0.450 V (vs. saturated calomel electrode (SCE)) with catalysis of Hb-loaded electrode and its dechlorination was stepwise, following the pathway of TCAA-->dichloroacetic acid (DCAA)-->monochloroacetic acid (MCAA)-->acetic acid. It was also found that all CAAs, e.g., TCAA, DCAA and MCAA, could be dechlorinated completely at -0.450 V. The removal of 30.0 mM TCAA and DCAA is ca. 40% and 31%, respectively, with electrolysis for 100 min at -0.600 V (vs. SCE) using the Hb-loaded packed-bed flow reactor. The dechlorination activities of CAAs follow the decreasing order: TCAA>DCAA>MCAA, and the average current efficiency is over 90%.     

Trihalomethane formation during water disinfection in four water supplies in the Somes river basin in Romania

Background, aim and scope

After the discovery of chloroform in drinking water, an extensive amount of work has been dedicated to the factors influencing the formation of halogenated disinfections by-products (DBPs). The disinfection practice can vary significantly from one country to another. Whereas no disinfectant is added to many water supplies in Switzerland or no disinfectant residual is maintained in the distribution system, high disinfectant doses are applied together with high residual concentrations in the distribution system in other countries such as the USA or some southern European countries and Romania. In the present study, several treatment plants in the Somes river basin in Romania were investigated with regard to chlorine practice and DBP formation (trihalomethanes (THMs)). Laboratory kinetic studies were also performed to investigate whether there is a relationship between raw water dissolved organic matter, residual chlorine, water temperature and THM formation.

Materials and methods

Drinking water samples were collected from different sampling points in the water treatment plant (WTP) from Gilau and the corresponding distribution system in Cluj-Napoca and also from Beclean, Dej and Jibou WTPs. The water samples were collected once a month from July 2006 to November 2007 and stored in 40-mL vials closed with Teflon lined screw caps. Water samples were preserved at 4°C until analysis after sodium thiosulfate (Na₂S₂O₃) had been added to quench residual chlorine. All samples were analysed for THMs using headspace GC-ECD between 1 and 7 days after sampling. The sample (10 mL) was filled into 20-mL headspace vials and closed with a Teflon-lined screw cap. Thereafter, the samples were equilibrated in an oven at 60°C for 45 min. The headspace (1 mL) was then injected into the GC (Cyanopropylphenyl Polysiloxane column, 30 m × 53 mm, 3 μm film thickness, Thermo Finnigan, USA). The MDLs for THMs were determined from the standard deviation of eight standards at 1 μg/L. The MDLs for CHCl₃, CHBrCl₂, CHBr₂Cl and CHBr₃ were 0.3, 0.2, 0.3 and 0.6 μg/L, respectively. All kinetic laboratory studies were carried out only with water from the WTP Gilau. The experiments were conducted under two conditions: baseline conditions (pH 7, 21°C, 2.5 mg/L Cl₂) to gain information about the change of the organic matter in the raw water and seasonally variable conditions to simulate the actual process at the treatment plant and the distribution system.

Results and discussion

This study shows that the current chlorination practice in the investigated plants complies with the THM drinking water standards of the EU. The THM concentrations in all samples taken in the four treatment plants and distributions systems were below the EU drinking water standard for TTHMs of 100 μg/L. Due to the low bromide levels in the raw waters, the main THM formed in the investigated plants is chloroform. It could also be seen that the THM levels were typically lower in water supplies with groundwater as their water resource. In one plant (Dej) with a pre-ozonation step, a significantly lower (50%) THM formation during post-chlorination was observed. Laboratory chlorination experiments revealed a good correlation between chloroform formation and the consumed chlorine dose. Also, these experiments allowed a semi-quantative prediction of the chloroform formation in the distribution system of Cluj-Napoca.

Conclusions

CHCl₃ was the most important trihalomethane species observed after the chlorination of water in all of the sampled months. However, TTHM concentrations did not exceed the maximum permissible value of 100 μg/L (EU). The THM formation rates in the distribution system of Cluj-Napoca have a high seasonal variability. Kinetic laboratory experiments could be used to predict chloroform formation in the Cluj-Napoca distribution system. Furthermore, an empirical model allowed an estimation of the chloroform formation in the Gilau water treatment plant.

     

Approximation and spatial regionalization of rainfall erosivity based on sparse data in a mountainous catchment of the Yangtze River in Central China

In densely populated countries like China, clean water is one of the most challenging issues of prospective politics and environmental planning. Water pollution and eutrophication by excessive input of nitrogen and phosphorous from nonpoint sources is mostly linked to soil erosion from agricultural land. In order to prevent such water pollution by diffuse matter fluxes, knowledge about the extent of soil loss and the spatial distribution of hot spots of soil erosion is essential. In remote areas such as the mountainous regions of the upper and middle reaches of the Yangtze River, rainfall data are scarce. Since rainfall erosivity is one of the key factors in soil erosion modeling, e.g., expressed as R factor in the Revised Universal Soil Loss Equation model, a methodology is needed to spatially determine rainfall erosivity. Our study aims at the approximation and spatial regionalization of rainfall erosivity from sparse data in the large (3,200 km²) and strongly mountainous catchment of the Xiangxi River, a first order tributary to the Yangtze River close to the Three Gorges Dam. As data on rainfall were only obtainable in daily records for one climate station in the central part of the catchment and five stations in its surrounding area, we approximated rainfall erosivity as R factors using regression analysis combined with elevation bands derived from a digital elevation model. The mean annual R factor (R _a) amounts for approximately 5,222 MJ?mm?ha^?1?h^?1?a^?1. With increasing altitudes, R _a rises up to maximum 7,547 MJ?mm ha^?1?h^?1 a^?1 at an altitude of 3,078 m a.s.l. At the outlet of the Xiangxi catchment erosivity is at minimum with approximate R _a?=?1,986 MJ?mm?ha^?1?h^?1?a^?1. The comparison of our results with R factors from high-resolution measurements at comparable study sites close to the Xiangxi catchment shows good consistance and allows us to calculate grid-based R _a as input for a spatially high-resolution and area-specific assessment of soil erosion risk.     

Identification and quantitative detection of Legionella spp. in various aquatic environments by real-time PCR assay

In this study, a SYBR green quantitative real-time PCR was developed to quantify and detect the Legionella spp. in various environmental water samples. The water samples were taken from watershed, water treatment plant, and thermal spring area in Taiwan. Legionella was detected in 13.6 % (24/176), and the detection rate for river water, raw drinking water, and thermal spring water was 10, 21.4, and 16.6 %, respectively. Using real-time PCR, concentration of Legionella spp. in detected samples ranged between 9.75?×?10⁴ and 3.47?×?10⁵?cells/L in river water, 6.92?×?10⁴ and 4.29?×?10⁵?cells/L in raw drinking water, and 5.71?×?10⁴ and 2.12?×?10⁶?cells/L for thermal spring water samples. The identified species included Legionella pneumophila (20.8 %), Legionella jordanis (4.2 %), Legionella nautarum (4.2 %), Legionella sp. (4.2 %), and uncultured Legionella sp. (66.6 %). The presence of L. pneumophila in aquatic environments suggested a potential public health threat that must be further examined.     

Depth-dependence and monthly variability of charophyte biomass production: consequences for the precipitation of calcium carbonate in a shallow <Emphasis Type="Italic">Chara</Emphasis>-lake

The month-to-month variability of biomass and CaCO₃ precipitation by dense charophyte beds was studied in a shallow Chara-lake at two depths, 1 and 3 m. Charophyte dry weights (d.w.), the percentage contribution of calcium carbonate to the dry weight and the precipitation of CaCO₃ per 1 m² were analysed from May to October 2011. Physical-chemical parameters of water were also measured for the same sample locations. The mean dry weight and calcium carbonate precipitation were significantly higher at 1 m than at 3 m. The highest measured charophyte dry weight (exceeding 2000 g m^?2) was noted at 1 m depth in September, and the highest CaCO₃ content in the d.w. (exceeding 80 % of d.w.) was observed at 3 m depth in August. The highest CaCO₃ precipitation per 1 m² exceeded 1695 g at 1 m depth in August. Significant differences in photosynthetically active radiation (PAR) were found between 1 and 3 m depths; there were no significant differences between depths for other water properties. At both sampling depths, there were distinct correlations between the d.w., CaCO₃ content and precipitation and water properties. In addition to PAR, the water temperature and magnesium and calcium ion concentrations were among the most significant determinants of CaCO₃ content and d.w. The results show that light availability seems to be the major factor in determining charophyte biomass in a typical, undisturbed Chara-lake. The study results are discussed in light of the role of charophyte vegetation in whole ecosystem functioning, with a particular focus on sedimentary processes and the biogeochemical cycle within the littoral zone.     

Nitrogen and plant population change radiation capture and utilization capacity of sunflower in semi-arid environment

The combination of nitrogen and plant population expresses the spatial distribution of crop plants. The spatial distribution influences canopy structure and development, radiation capture, accumulated intercepted radiation (Sa), radiation use efficiency (RUE), and subsequently dry matter production. We hypothesized that the sunflower crop at higher plant populations and nitrogen (N) rates would achieve early canopy cover, capture more radiant energy, utilize radiation energy more efficiently, and ultimately increase economic yield. To investigate the above hypothesis, we examined the influences of leaf area index (LAI) at different plant populations (83,333, 66,666, and 55,555 plants ha^?1) and N rates (90, 120, and 150 kg ha^?1) on radiation interception (Fi), photosynthetically active radiation (PAR) accumulation (Sa), total dry matter (TDM), achene yield (AY), and RUE of sunflower. The experimental work was conducted during 2012 and 2013 on sandy loam soil in Punjab, Pakistan. The sunflower crop captured more than 96% of incident radiant energy (mean of all treatments), 98% with a higher plant population (83,333 plants ha^?1), and 97% with higher N application (150 kg ha^?1) at the fifth harvest (60 days after sowing) during both study years. The plant population of 83,333 plants ha^?1 with 150 kg N ha^?1 ominously promoted crop, RUE, and finally productivity of sunflower (AY and TDM). Sunflower canopy (LAI) showed a very close and strong association with Fi (R ² = 0.99 in both years), PAR (R ² = 0.74 and 0.79 in 2012 and 2013, respectively), TDM (R ² = 0.97 in 2012 and 0.91 in 2013), AY (R ² = 0.95 in both years), RUE for TDM (RUE_TDM) (R ² = 0.63 and 0.71 in 2012 and 2013, respectively), and RUE for AY (RUE_AY) (R ² = 0.88 and 0.87 in 2012 and 2013, respectively). Similarly, AY (R ² = 0.73 in 2012 and 0.79 in 2013) and TDM (R ² = 0.75 in 2012 and 0.84 in 2013) indicated significant dependence on PAR accumulation of sunflower. High temperature during the flowering stage in 2013 shortened the crop maturity duration, which reduced the LAI, leaf area duration (LAD), crop growth rate (CGR), TDM, AY, Fi, Sa, and RUE of sunflower. Our results clearly revealed that RUE was enhanced as plant population and N application rates were increased and biomass assimilation in semi-arid environments varied with radiation capture capacity of sunflower.     

Development,validation, and application of a method for the GC-MS analysis of fipronil and three of its degradation products in samples of water,soil, and sediment

A method for the identification and quantification of pesticide residues in water, soil, and sediment samples has been developed, validated, and applied for the analysis of real samples. The specificity was determined by the retention time and the confirmation and quantification of analyte ions. Linearity was demonstrated over the concentration range of 20 to 120 µg L^?1, and the correlation coefficients varied between 0.979 and 0.996, depending on the analytes. The recovery rates for all analytes in the studied matrix were between 86% and 112%. The intermediate precision and repeatability were determined at three concentration levels (40, 80, and 120 µg L^?1), with the relative standard deviation for the intermediate precision between 1% and 5.3% and the repeatability varying between 2% and 13.4% for individual analytes. The limits of detection and quantification for fipronil, fipronil sulfide, fipronil-sulfone, and fipronil-desulfinyl were 6.2, 3.0, 6.6, and 4.0 ng L^?1 and 20.4, 9.0, 21.6, and 13.0 ng L^?1, respectively. The method developed was used in water, soil, and sediment samples containing 2.1 mg L^?1 and 1.2% and 5.3% of carbon, respectively. The recovery of pesticides in the environmental matrices varied from 88.26 to 109.63% for the lowest fortification level (40 and 100 µg kg^?1), from 91.17 to 110.18% for the intermediate level (80 and 200 µg kg^?1), and from 89.09 to 109.82% for the highest fortification level (120 and 300 µg kg^?1). The relative standard deviation for the recovery of pesticides was under 15%.     

A novel low-cost detection method for screening of arsenic in groundwater

In the present work, a novel and simple detection system for As inorganic species contained in groundwater is presented. To reach the required detection limit, the proposed methodology is based on two steps: first is the transport and preconcentration of the inorganic arsenic species using a polymer inclusion membrane (PIM) system and second is the formation of a coloured complex, the  absorbance of which is measured. Different parameters related to the membrane composition and the transport kinetics have been studied, and it was found that membranes made of polyvinyl chloride (PVC) as a polymer, and Aliquat 336 as a carrier, ensured efficient arsenic transport when the carrier content was at least 31 % (w/w). The implementation of the designed PIM in a special device that contained only 5 mL of the stripping solution (0.1 M NaCl) allowed As preconcentration from a 100-mL water sample, thus facilitating its detection with the colorimetric method. The new method developed here was validated, and its analytical figures of merit were determined, i.e. limit of detection of 4.5 μg L^?1 at 820 nm and a relative standard deviation within the range 8–10 %. Finally, the method was successfully applied to the analysis of different water samples from Catalonia region with naturally occurring As.     

Simultaneous determination of estrogenic odorant alkylphenols,chlorophenols, and their derivatives in water using online headspace solid phase microextraction coupled with gas chromatography-mass spectrometry

A simple online headspace solid-phase microextraction (HS-SPME) coupled with the gas chromatography-mass spectrometry (GC-MS) method was developed for simultaneous determination of trace amounts of nine estrogenic odorant alkylphenols and chlorophenols and their derivatives in water samples. The extraction conditions of HS-SPME were optimized including fiber selection, extraction temperature, extraction time, and salt concentration. Results showed that divinylbenzene/Carboxen/polydimethylsiloxane (DVB/CAR/PDMS) fiber was the most appropriate one among the three selected commercial fibers, and the optimal extraction temperature, time, and salt concentration were 70 °C, 30 min, and 0.25 g/mL, respectively. The developed method was validated and showed good linearity (R ²?>?0.989), low limit of detection (LOD, 0.002–0.5 μg/L), and excellent recoveries (76–126 %) with low relative standard deviation (RSD, 0.7–12.9 %). The developed method was finally applied to two surface water samples and some of these target compounds were detected. All these detected compounds were below their odor thresholds, except for 2,4,6-TCAS and 2,4,6-TBAS wherein their concentrations were near their odor thresholds. However, in the two surface water samples, these detected compounds contributed to a certain amount of estrogenicity, which seemed to suggest that more attention should be paid to the issue of estrogenicity rather than to the odor problem.     

Potential of the TCE-degrading endophyte Pseudomonas putida W619-TCE to improve plant growth and reduce TCE phytotoxicity and evapotranspiration in poplar cuttings

The TCE-degrading poplar endophyte Pseudomonas putida W619-TCE was inoculated in poplar cuttings, exposed to 0, 200 and 400 mg l⁻¹ TCE, that were grown in two different experimental setups. During a short-term experiment, plants were grown hydroponically in half strength Hoagland nutrient solution and exposed to TCE for 3 days. Inoculation with P. putida W619-TCE promoted plant growth, reduced TCE phytotoxicity and reduced the amount of TCE present in the leaves. During a mid-term experiment, plants were grown in potting soil and exposed to TCE for 3 weeks. Here, inoculation with P. putida W619-TCE had a less pronounced positive effect on plant growth and TCE phytotoxicity, but resulted in strongly reduced amounts of TCE in leaves and roots of plants exposed to 400 mg l⁻¹ TCE, accompanied by a lowered evapotranspiration of TCE. Dichloroacetic acid (DCAA) and trichloroacetic acid (TCAA), which are known intermediates of TCE degradation, were not detected.     

Characterization of carbonaceous aerosols over Delhi in Ganga basin: seasonal variability and possible sources

The mass concentration of carbonaceous species, organic carbon (OC), and elemental carbon (EC) using a semicontinuous thermo-optical EC-OC analyzer, and black carbon (BC) using an Aethalometer were measured simultaneously at an urban mega city Delhi in Ganga basin from January 2011 to May 2012. The concentrations of OC, EC, and BC exhibit seasonal variability, and their concentrations were ～2 times higher during winter (OC 38.1?±?17.9 μg m^?3, EC 15.8?±?7.3 μg m^?3, and BC 10.1?±?5.3 μg m^?3) compared to those in summer (OC 14.1?±?4.3 μg m^?3, EC 7.5?±?1.5 μg m^?3, and BC 4.9?±?1.5 μg m^?3). A significant correlation between OC and EC (R?=?0.95, n?=?232) indicate their common emission sources with relatively lower OC/EC ratio (range 1.0–3.6, mean 2.2?±?0.5) suggests fossil fuel emission as a major source of carbonaceous aerosols over the station. On average, mass concentration of EC was found to be ～38 % higher than BC during the study period. The measured absorption coefficient (b_abs) was significantly correlated with EC, suggesting EC as a major absorbing species in ambient aerosols at Delhi. Furthermore, the estimated mass absorption efficiency (σ_abs) values are similar during winter (5.0?±?1.5 m² g^?1) and summer (4.8?±?2.8 m² g^?1). Significantly high aerosol loading of carbonaceous species emphasize an urgent need to focus on air quality management and proper impact assessment on health perspective in these regions.     

Kinetics of phenol biodegradation at high concentration by a metabolically versatile isolated yeast Candida tropicalis PHB5

A highly tolerant phenol-degrading yeast strain PHB5 was isolated from wastewater effluent of a coke oven plant and identified as Candida tropicalis based on phylogenetic analysis. Biodegradation experiments with C. tropicalis PHB5 showed that the strain was able to utilize 99.4 % of 2,400 mg l^?1 phenol as sole source of carbon and energy within 48 h. Strain PHB5 was also observed to grow on 18 various aromatic hydrocarbons. Haldane model was used to fit the exponential growth data and the following kinetic parameters were obtained: μ _max?=?0.3407 h^?1, K _S?=?15.81 mg l^?1, K _i?=?169.0 mg l^?1 (R ²?=?0.9886). The true specific growth rate, calculated from μ _max, was 0.2113. A volumetric phenol degradation rate (V _max) was calculated by fitting the phenol consumption data with Gompertz model and specific degradation rate (q) was calculated from V _max. The q values were fitted with Haldane model, yielding following parameters: q _max?=?0.2766 g g^?1 h^?1, K _S ′?=?2.819 mg l^?1, K _i ′?=?2,093 (R ²?=?0.8176). The yield factor (Y _X/S ) varied between 0.185 to 0.96 g g^?1 for different initial phenol concentrations. Phenol degradation by the strain proceeded through a pathway involving production of intermediates such as catechol and cis,cis-muconic acid which were identified by enzymatic assays and HPLC analysis.     

Assessment of sewage sludge bioremediation at different hydraulic retention times using mixed fungal inoculation by liquid-state bioconversion

Sustainable, environmental friendly, and safe disposal of sewage treatment plant (STP) sludge is a global expectation. Bioremediation performance was examined at different hydraulic retention times (HRT) in 3–10 days and organic loading rates (OLR) at 0.66–7.81 g chemical oxygen demand (COD) per liter per day, with mixed filamentous fungal (Aspergillus niger and Penicillium corylophilum) inoculation by liquid-state bioconversion (LSB) technique as a continuous process in large-scale bioreactor. Encouraging results were monitored in treated sludge by LSB continuous process. The highest removal of total suspended solid (TSS), turbidity, and COD were achieved at 98, 99, and 93 %, respectively, at 10 days HRT compared to control. The minimum volatile suspended solid/suspended solid implies the quality of water, which was recorded 0.59 at 10 days and 0.72 at 3 days of HRT. In treated supernatant with 88 % protein removal at 10 days of HRT indicates a higher magnitude of purification of treated sludge. The specific resistance to filtration (SRF) quantifies the performance of dewaterability; it was recorded minimum 0.049 × 10¹² m kg^?1 at 10 days of HRT, which was equivalent to 97 % decrease of SRF. The lower OLR and higher HRT directly influenced the bioremediation and dewaterability of STP sludge in LSB process. The obtained findings imply encouraging message in continuing treatment of STP sludge, i.e., bioremediation of wastewater for environmental friendly disposal in near future.     

Extraction of Sudan dyes from environmental water by hemimicelles-based magnetic titanium dioxide nanoparticles

A novel method for the extraction of Sudan dyes including Sudan I, II, III, and IV from environmental water by magnetic titanium dioxide nanoparticles (Fe₃O₄@TiO₂) coated with sodium dodecylsulfate (SDS) as adsorbent was reported. Fe₃O₄@TiO₂ was synthesized by a simple method and was characterized by transmission electron microscopy, Fourier-transform infrared spectrometry, and vibrating sample magnetometer. The magnetic separation was quite efficient for the adsorption and desorption of Sudan dyes. The effect of the amount of SDS, extraction time, pH, desorption condition, maximal extraction volume, and humic acid on the extraction process were investigated. This method was employed to analyze three environmental water samples. The results demonstrated that our proposed method had wide linear range (25–5,000 ng L^?1) with a good linearity (R ²?>?0.999) and low detection limits (2.9–7.3 ng L^?1). An enrichment factor of 1,000 was achieved. In all three spiked levels (25, 250, and 2,500 ng L^?1), the recoveries of Sudan dyes were in the range of 86.9–93.6 %. The relative standard deviations obtained were ranging from 2.5 to 9.3 %. That is to say, the new method was fast and effective for the extraction of Sudan dye from environmental water.     

Dietary arsenic consumption and urine arsenic in an endemic population: response to improvement of drinking water quality in a 2-year consecutive study

We assessed the association between arsenic intake through water and diet, and arsenic levels in first morning-void urine under variable conditions of water contamination. This was done in a 2-year consecutive study in an endemic population. Exposure of arsenic through water and diet was assessed for participants using arsenic-contaminated water (≥50 μg L^?1) in a first year (group I) and for participants using water lower in arsenic (<50 μg L^?1) in the next year (group II). Participants with and without arsenical skin lesions were considered in the statistical analysis. Median dose of arsenic intake through drinking water in groups I and II males was 7.44 and 0.85 μg kg body wt.^?1 day^?1 (p <0.0001). In females, it was 5.3 and 0.63 μg kg body wt.^?1 day^?1 (p <0.0001) for groups I and II, respectively. Arsenic dose through diet was 3.3 and 2.6 μg kg body wt.^?1 day^?1 (p?=?0.088) in males and 2.6 and 1.9 μg kg body wt.^?1 day^?1 (p?=?0.0081) in females. Median arsenic levels in urine of groups I and II males were 124 and 61 μg L^?1 (p?=?0.052) and in females 130 and 52 μg L^?1 (p?=?0.0001), respectively. When arsenic levels in the water were reduced to below 50 μg L^?1 (Indian permissible limit), total arsenic intake and arsenic intake through the water significantly decreased, but arsenic uptake through the diet was found to be not significantly affected. Moreover, it was found that drinking water mainly contributed to variations in urine arsenic concentrations. However, differences between male and female participants also indicate that not only arsenic uptake, but also many physiological factors affect arsenic behavior in the body and its excretion. As total median arsenic exposure still often exceeded 3.0 μg kg body wt.^?1 day^?1 (the permissible lower limit established by the Joint Expert Committee on Food Additives) after installation of the drinking water filters, it can be concluded that supplying the filtered water only may not be sufficient to minimize arsenic availability for an already endemic population.     

The capability of estuarine sediments to remove nitrogen: implications for drinking water resource in Yangtze Estuary

Water in the Yangtze Estuary is fresh most of the year because of the large discharge of Yangtze River. The Qingcaosha Reservoir built on the Changxing Island in the Yangtze Estuary is an estuarine reservoir for drinking water. Denitrification rate in the top 10 cm sediment of the intertidal marshes and bare mudflat of Yangtze Estuarine islands was measured by the acetylene inhibition method. Annual denitrification rate in the top 10 cm of sediment was 23.1 μmol m^?2 h^?1 in marshes (ranged from 7.5 to 42.1 μmol m^?2 h^?1) and 15.1 μmol m^?2 h^?1 at the mudflat (ranged from 6.6 to 26.5 μmol m^?2 h^?1). Annual average denitrification rate is higher at mashes than at mudflat, but without a significant difference (p?=?0.084, paired t test.). Taking into account the vegetation and water area of the reservoir, a total 1.42?×?10⁸ g N could be converted into nitrogen gas (N₂) annually by the sediment, which is 97.7 % of the dissolved inorganic nitrogen input through precipitation. Denitrification in reservoir sediment can control the bioavailable nitrogen level of the water body. At the Yangtze estuary, denitrification primarily took place in the top 4 cm of sediment, and there was no significant spatial or temporal variation of denitrification during the year at the marshes and mudflat, which led to no single factor determining the denitrification process but the combined effects of the environmental factors, hydrologic condition, and wetland vegetation.     

Preliminary toxicological assessment of phthalate esters from drinking water consumed in Portugal

This paper reports, for the first time, the concentrations of selected phthalates in drinking water consumed in Portugal. The use of bottled water in Portugal has increased in recent years. The main material for bottles is polyethylene terephthalate (PET). Its plasticizer components can contaminate water by leaching, and several scientific studies have evidenced potential health risks of phthalates to humans of all ages. With water being one of the most essential elements to human health and because it is consumed by ingestion, the evaluation of drinking water quality, with respect to phthalate contents, is important. This study tested seven commercial brands of bottled water consumed in Portugal, six PET and one glass (the most consumed) bottled water. Furthermore, tap water from Lisbon and three small neighbor cities was analyzed. Phthalates (di-n-butyl phthalate ester (DnBP), bis(2-ethylhexyl) phthalate ester (DEHP), and di-i-butyl phthalate ester (DIBP)) in water samples were quantified (PET and glass) by means of direct immersion solid-phase microextraction and ionic liquid gas chromatography associated with flame ionization detection or mass spectrometry due to their high boiling points and water solubility. The method utilized in this study showed a linear range for target phthalates between 0.02 and 6.5 μg L^?1, good precision and low limits of detection that were between 0.01 and 0.06 μg L^?1, and quantitation between 0.04 and 0.19 μg L^?1. Only three phthalates were detected in Portuguese drinking waters: dibutyl (DnBP), diisobutyl (DIBP), and di(ethylhexyl) phthalate (DEHP). Concentrations ranged between 0.06 and 6.5 μg L^?1 for DnBP, between 0.02 and 0.16 μg L^?1 for DEHP, and between 0.1 and 1.89 μg L^?1 for DIBP. The concentration of DEHP was found to be up to five times higher in PET than in glass bottled water. Surprisingly, all the three phthalates were detected in glass bottled water with the amount of DnBP being higher (6.5 μg L^?1) than in PET bottled water. These concentrations do not represent direct risk to human health. Regarding potable tap water, only DIBP and DEHP were detected. Two of the cities showed concentration of all three phthalates in their water below the limits of detection of the method. All the samples showed phthalate concentrations below 6 μg L^?1, the maximum admissible concentration in water established by the US Environmental Protection Agency. The concentrations measured in Portuguese bottled waters do not represent any risk for adult's health.