Dry deposition of particles to wave surfaces: II. Wind tunnel experiments

Wind tunnel measurements of particle dry deposition to wavy and flat surfaces were made to estimate the enhancement of deposition rates due to waves on water surfaces. Measurements were made of 4.0 and 6.7 μm uranine particles at wind speeds of 5 and 10 m s⁻¹ to sinusoidal waves with height to length ratios 2a/λ=0.1 and 0.03 and to flat surfaces. Results showed that deposition was greatest to the upslope portion of the wave, accounting for 40–45% of the total mass, followed by the trough (30%), downslope (15%), and crest (10–15%). These results generally agreed within experimental variability with modeling predictions (Zufall et al., 1999). Deposition was enhanced at the upslope due to the effects of particle interception and impaction on the wave. Total deposition to the wave surfaces was greater than deposition to the flat surface for a large majority of the cases. The average increase in deposition to both wave surfaces for both particle sizes and wind speeds over deposition to the flat surface was 80%.     

On applicability of model aerosol distributions for urban region of Bratislava city

Long-term measurements of spectral atmospheric transparency are analysed to describe the aerosol size distribution as well as the aerosol optical thickness in the urban region of Bratislava city, capital of Slovak Republic. Aerosol characteristics are related to the most frequent air masses, especially to the continental polar (cP—with a 54% occurrence) and maritime polar (mP—with 34% occurrence), to the wind direction and speed, as well as to the relative humidity. Including both random and systematic errors of the observations into the calculation procedures, the aerosol optical thickness is obtained with approximately 4% error at all wavelengths. Averaged values of the aerosol optical thickness τ_a(λ) at reference wavelength λ=520 nm vary over a wide range, from 0.1 to 0.7. Besides, the aerosol optical thickness of the continental polar air mass is obviously higher than corresponding values in the maritime polar air mass. It is shown that the transformation inside the air mass reflects the changes of the optical characteristics of aerosols, especially during decay of air mass. The function τ_a(λ) seems to be monomodal in the majority of cases, with the mode position about λ≈400 nm for cP, and λ≈500 nm for mP. A value of power parameter δ of the function τ_a(λ)≈λ^−δ is about 0.8–1.6 for maritime polar and about 0.3–1.2 for continental polar. Two simple model functions (Junge and gamma) are examined to find a best fit of real distribution retrieved from the aerosol optical thickness data using the inverse techniques based on Mellin transform. The gamma function much better than Junge's function supply the real aerosol component of all studied air masses (mainly for cP and mP). The average modal radius of gamma distribution practically does not exceed the value of 0.06 μm. Real distributions retrieved using a Mellin transform give an averaged morning value of particle modal radius r_m about 0.084 μm, and averaged daily value r_m about 0.054 μm.     

Influence of the surface microlayer on atmospheric deposition of aerosols and polycyclic aromatic hydrocarbons

Atmospheric dry deposition is an important process for the introduction of aerosols and pollutants to aquatic environments. The objective of this paper is to assess, for the first time, the influence that the aquatic surface microlayer plays as a modifying factor of the magnitude of dry aerosol deposition fluxes. The occurrence of a low surface tension (ST) or a hydrophobic surface microlayer has been generated by spiking milli-Q water or pre-filtered seawater with a surfactant or octanol, respectively. The results show that fine mode (<2.7 μm) aerosol phase PAHs deposit with fluxes 2–3 fold higher when there is a low ST aquatic surface due to enhanced sequestration of colliding particles at the surface. Conversely, for PAHs bound to coarse mode aerosols (>2.7 μm), even though there is an enhanced deposition due to the surface microlayer for some sampling periods, the effect is not observed consistently. This is due to the importance of gravitational settling for large aerosols, rendering a lower influence of the aquatic surface on dry deposition fluxes. ST (mN m⁻¹) is identified as one of the key factor driving the magnitude of PAH dry deposition fluxes (ng m⁻² d⁻¹) by its influence on PAH concentrations in deposited aerosols and deposition velocities (v_d, cm s⁻¹). Indeed, v_d values are a function of ST as obtained by least square fitting and given by Ln(v_d)=−1.77 Ln(ST)+5.74 (r²=0.95) under low wind speed (average 4 m s⁻¹) conditions.     

Quantitative analysis of volatile organic compounds (VOCs) in atmospheric particles

There are a number of difficulties associated with the quantitative analysis of volatile organic compounds (VOCs) in atmospheric particles. Therefore, majority of the previous studies on VOCs associated with particles have been qualitative. Air samples were collected in Izmir, Turkey to determine ambient particle and gas phase concentrations of several aromatic, oxygenated and halogenated VOCs. Samples were quantitatively analyzed using thermal desorption–gas chromatography/mass spectrometry. Gas-phase concentrations ranged between 0.02 (bromoform) and 4.65 μg m⁻³ (toluene) and were similar to those previously measured at the same site. Particle-phase concentrations ranged from 1 (1,3-dichlorobenzene) to 933 pg m⁻³ (butanol). VOCs were mostly found in gas-phase (99.9±0.25%). However, the particulate VOCs had comparable concentrations to those reported previously for semivolatile organic compounds. The distribution of particle-phase VOCs between fine (d_p<2.5 μm) and coarse (2.5 μm<d_p<10 μm) fractions was also investigated. It was found that VOCs were mostly associated with fine particles.     

The effect of humidity and state of water surfaces on deposition of aerosol particles onto a water surface

Deposition processes of particles with dry diameter larger than about 10 μm are dominated by gravitational settling, while molecular diffusion and Brownian motion predominate the deposition processes of particles smaller than 0.1 μm in dry diameter. Many air pollution derived elements exhibit characteristics common to sub-micron particles. The objective of the present study is to examine the effects of meteorological conditions within the turbulent transfer layer on the deposition velocity of particles with dry diameter between 0.1 and 1 μm. It is for these sub-micron particles that particle growth by condensation in the deposition layer, the broken water surface effect and the enhanced transfer process due to atmospheric turbulence in the turbulent transfer layer play important roles in controlling the particle deposition velocity. Results of the present study show that the `dry air’ assumption of Williams’ model is unrealistic. Effects of ambient air relative humidity and water surface temperature cannot be ignored in determining the deposition velocity over a water surface. Neglecting effects of ambient air relative humidity and water surface temperature will result in defining atmospheric stability incorrectly. It is found that the largest effect of air relative humidity on deposition velocity occurs at an air–water temperature difference corresponding to the point of `displaced neutral stability'. For a given wind speed of U=5 m s⁻¹ the additive effects of water surface temperature, T_w, changes from 5 to 25°C and ambient air relative humidity variations from 85 to 60%, respectively, lead to a maximum difference in v_d of about 20%. For a higher wind speed of 10 m s⁻¹, however, the corresponding change in v_d reduces to less than 5%. This is further confirmation that wind speed is one of the strongest variables that governs the magnitude of v_d. The present study also found that the broken surface transfer coefficient, k_bs, given as a multiple of the smooth surface transfer coefficient, k_ss, is physically more meaningful than assigning it a constant value independent of particle size. The method used in this study requires only a single level of atmospheric data coupled with the surface temperature measurement. The present method is applicable for determining deposition velocity not only at the conventional measurement height of 10 m but also at any other heights that are different from the measurement height.     

The physical characteristics of sulfur aerosols

A review of the physical characteristics of sulfur-containing aerosols, with respect to size distribution of the physical distributions, sulfur distributions, distribution modal characteristics, nuclei formation rates, aerosol growth characteristics, and in situ measurement, has been made.Physical size distributions can be characterized well by a trimodal model consisting of three additive lognormal distributions.When atmospheric physical aerosol size distributions are characterized by the trimodal model, the following typical modal parameters are observed:1. Nuclei mode – geometric mean size by volume, DGV_n, from 0.015 to 0.04 μm. σ_gn=1.6, nucler mode volumes from 0.0005 over the remote oceans to 9 μm³ cm⁻³ on an urban freeway.2. Accumulation mode – geometric mean size by volume, DGV_a, from 0.15 to 0.5 μm, σ_ga=1.6–2.2 and mode volume concentrations from 1 for very clean marine or continental backgrounds to as high as 300 μm³ cm⁻³ under very polluted conditions in urban areas.3. Coarse particle mode – geometric mean size by volume, DGV_c, from 5 to 30 μm, σ_gn=2–3, and mode volume concentrations from 2 to 1000 μm³ cm⁻³.It has also been concluded that the fine particles (D_p<2 μm) are essentially independent in formation, transformation and removal from the coarse particles (D_p>2 μm).Modal characterization of impactor-measured sulfate size distributions from the literature shows that the sulfate is nearly all in the accumulation mode and has the same size distribution as the physical accumulation mode distribution.Average sulfate aerodynamic geometric mean dia. was found to be 0.48±0.1 μm (0.37±0.1 μm vol. dia.) and σ_g=2.00±0.29. Concentrations range from a low of about 0.04 μg m⁻³ over the remote oceans to over 8 μg m⁻³ under polluted conditions over the continents.Review of the data on nucleation in smog chambers and in the atmosphere suggests that when SO₂, is present, SO₂-to-aerosol conversion dominates the Aitken nuclei count and, indirectly, through coagulation and condensation, the accumulation mode size and concentration. There are indications that nucleation is ubiquitous in the atmosphere, ranging from values as low as 2 cm⁻³ h⁻¹ over the clean remote oceans to a high of 6×10⁶ cm⁻³ h⁻¹ in a power plant plume under sunny conditions.There is considerable theoretical and experimental evidence that even if most of the mass for the condensational growth of the accumulation mode comes from hydrocarbon conversion, sulfur conversion provides most of the nuclei.     

Size and seasonal distributions of airborne bioaerosols in commuting trains

Aerobiological studies in commuting trains in northern Taiwan were carried out from August, 2007 until July, 2008. Two six-stage (>7 μm, 4.7～7 μm, 3.3～4.7 μm, 2.1～3.3 μm, 1.1～2.1 μm, 0.65～1.1 μm) cascade impactors of 400 orifices were used to collect viable bacteria and fungi, respectively. The levels of carbon monoxide (CO), carbon dioxide (CO₂), formaldehyde (HCHO), temperature, and relative humidity in the commuting trains were also recorded during the sampling period. Results show that bacterial concentrations ranged from 25 to 1530 CFU m^?3, and averaged 417 CFU m^?3. The fungal concentrations ranged from 45 to 1906 CFU m^?3, and averaged 413 CFU m^?3. Additionally, the highest fractions occurred in the fifth stage (1.1～2.1 μm) for both bacteria and fungi. The respirable fractions, R_b and R_f, for bacteria and fungi were 62.8% and 81.4%, respectively, which are higher than those in other studies. Furthermore, the bacterial concentration reached its highest level in autumn, and its lowest level in winter. However, the fungal concentration was highest in spring and lowest in winter. Though the total bacterial or fungal concentration did not exceed the recommendation standard in Taiwan, the relatively high respirable fraction in commuting trains probably implies a higher adverse health risk for sensitive commuters. This study further conducted multiple regression analysis to determine the relationship of various stage fractions of airborne bacteria and fungi with indoor air pollutants (CO and HCHO) and environmental parameters (CO₂, temperature, and relative humidity). The correlation coefficients of multiple regression analysis for total bacteria and fungi concentrations with indoor air pollutants and environmental parameters were 0.707 (p < 0.00376) and 0.612 (p < 0.00471), respectively. There are currently no formally regulated laws for indoor air quality (IAQ) in Taiwan, and this preliminary study can provide references to the Taiwan government on IAQ management.     

Biogenic emission of dimethylsulfide (DMS) from the North Yellow Sea,China and its contribution to sulfate in aerosol during summer

Seawater, atmospheric dimethylsulfide (DMS) and aerosol compounds, potentially linked with DMS oxidation, such as methanesulfonic acid (MSA) and non-sea-salt sulfate (nss-SO₄^2?) were determined in the North Yellow Sea, China during July–August, 2006. The concentrations of seawater and atmospheric DMS ranged from 2.01 to 11.79 nmol l^?1 and from 1.68 to 8.26 nmol m^?3, with average values of 6.20 nmol l^?1 and 5.01 nmol m^?3, respectively. Owing to the appreciable concentration gradient, DMS accumulated in the surface water was transferred into the atmosphere, leading to a net sea-to-air flux of 6.87 μmol m^?2 d^?1 during summer. In the surface seawater, high DMS values corresponded well with the concurrent increases in chlorophyll a levels and a significant correlation was observed between integrated DMS and chlorophyll a concentrations. In addition, the concentrations of MSA and nss-SO₄^2? measured in the aerosol samples ranged from 0.012 to 0.079 μg m^?3 and from 3.82 to 11.72 μg m^?3, with average values of 0.039 and 7.40 μg m^?3, respectively. Based on the observed MSA, nss-SO₄^2? and their ratio, the relative biogenic sulfur contribution was estimated to range from 1.2% to 11.5%, implying the major contribution of anthropogenic source to sulfur budget in the study area.     

Radon exhalation and ultrafine fraction of radon progeny in closed room air

The influence of ²²²Rn exhalation from walls and air exchange (low ventilation rates ν<0.3 h^-1) upon its concentration in room air has been considered. It was found that the radon concentration reachs 84 Bq m^-3 at exhalation and ventilation rates of 66 Bq hm^-2 and 0.28 h^-1, respectively. The radon concentration and the ultrafine fraction f_p of potential α energy concentration as well as the equilibrium factor F of the short-lived radon progeny were also determined in three different completely closed rooms. An electroprecipitation method was applied for determining the ²²²Rn concentration while a single wire-screen technique was used for the determination of ultrafine radon progeny. During the measurements, the radon concentrations were varied between 33 and 134 with a mean value 89 Bq m^-3. A mean ultrafine fraction (f_p) of 0.16 was obtained at a mean aerosol particle concentration (Z) of 1700 cm^-3 and a mean equilibrium factor (F) of 0.33. The obtained mean value of f_p was found to be about five times higher than the value reported in the ICRP publication (f_p=0.03). The attachment rate (X), the deposition rate (q^f) and the deposition velocity (v^f_d) of the ultrafine radionuclide ²¹⁸Po were calculated. A mean value of X was found to be 49 h^-1 at a mean q^f of 46 h^-1 and a mean v^f_d of 4.6 m h^-1. The attachment coefficient β of ²¹⁸Po was found to vary between 0.016 and 0.047 with a mean value 0.028 cm³ h^-1.     

Concentration-dependent NH3 deposition processes for moorland plant species with and without stomata

Currently, in operational modelling of NH₃ deposition a fixed value of canopy resistance (R_c) is generally applied, irrespective of the plant species and NH₃ concentration. This study determined the effect of NH₃ concentration on deposition processes to individual moorland species. An innovative flux chamber system was used to provide accurate continuous measurements of NH₃ deposition to Deschampsia cespitosa (L.) Beauv., Calluna vulgaris (L.) Hull, Eriophorum vaginatum L., Cladonia spp., Sphagnum spp., and Pleurozium schreberi (Brid.) Mitt. Measurements were conducted across a wide range of NH₃ concentrations (1–140 μg m⁻³).NH₃ concentration directly affects the deposition processes to the vegetation canopy, with R_c, and cuticular resistance (R_w) increasing with increasing NH₃ concentration, for all the species and vegetation communities tested. For example, the R_c for C. vulgaris increased from 14 s m⁻¹ at 2 μg m⁻³ to 112 s m⁻¹ at 80 μg m⁻³. Diurnal variations in NH₃ uptake were observed for higher plants, due to stomatal uptake; however, no diurnal variations were shown for non-stomatal plants. R_c for C. vulgaris at 80 μg m⁻³ was 66 and 112 s m⁻¹ during day and night, respectively. Differences were found in NH₃ deposition between plant species and vegetation communities: Sphagnum had the lowest R_c (3 s m⁻¹ at 2 μg m⁻³ to 23 at 80 μg m⁻³), and D. cespitosa had the highest nighttime value (18 s m⁻¹ at 2 μg m⁻³ to 197 s m⁻¹ at 80 μg m⁻³).     

Concentration-dependent NH3 deposition processes for mixed moorland semi-natural vegetation

Dry deposition modelling typically assumes that canopy resistance (R_c) is independent of ammonia (NH₃) concentration. An innovative flux chamber system was used to provide accurate continuous measurements of NH₃ deposition to a moorland composed of a mixture of Calluna vulgaris (L.) Hull, Eriophorum vaginatum L. and Sphagnum spp. Ammonia was applied at a wide range of concentrations (1–100 μg m⁻³). The physical and environmental properties and the testing of the chamber are described, as well as results for the moorland vegetation using the ‘canopy resistance’ and ‘canopy compensation point’ interpretations of the data.Results for moorland plant species demonstrate that NH₃ concentration directly affects the rate of NH₃ deposition to the vegetation canopy, with R_c and cuticular resistance (R_w) increasing with increasing NH₃ concentrations. Differences in R_c were found between night and day: during the night R_c increases from 17 s m⁻¹ at 10 μg m⁻³ to 95 s m⁻¹ at 80 μg m⁻³, whereas during the day R_c increases from 17 s m⁻¹ at 10 μg m⁻³ to 48 s m⁻¹ at 80 μg m⁻³. The lower resistance during the day is caused by the stomata being open and available as a deposition route to the plant. R_w increased with increasing NH₃ concentrations and was not significantly different between day and night (at 80 μg m⁻³ NH₃ day R_w=88 s m⁻¹ and night R_w=95 s m⁻¹). The results demonstrate that assessments using fixed R_c will over-estimate NH₃ deposition at high concentrations (over ∼15 μg m⁻³).     

Source apportionment of time and size resolved ambient particulate matter measured with a rotating DRUM impactor

Ambient particulate chemical composition data acquired from samples collected using a three-stage Davis Rotating-drum Universal-size-cut Monitoring (DRUM) impactor in Detroit, MI, between February and April 2002 were analyzed through the application of a three-way factor analysis model. PM_2.5 (particulate matter ⩽2.5 μm in aerodynamic diameter) was collected by a DRUM impactor with 3-h time resolution and three size modes (2.5 μm>D_p>1.15 μm, 1.15 μm>D_p>0.34 μm and 0.34 μm>D_p>0.1 μm). A novel three-way factor analysis model was applied to these data where the source profiles are a three-way array of size, composition and source while the contributions are a matrix of sample by source. Nine factors were identified: road salt, industrial (Fe+Zn), cloud processed sulfate, two types of metal works, road dust, local sulfate source, sulfur with dust, and homogeneously formed sulfate. Road salt had high concentrations of Na and Cl. Mixed industrial emissions are characterized by Fe and Zn. The cloud processed sulfate had a high concentration of S in the intermediate size mode. The first metal works represented by Fe in all three size modes and by Zn, Ti, Cu, and Mn. The second included a high concentration of small size particle sulfur with intermediate size Fe, Zn, Al, Si, and Ca. Road dust contained Na, Al, Si, S, K, and Fe in the large size mode. The local and homogeneous sulfate factors show high concentrations of S in the smallest size mode, but different time series behavior in their contributions. Sulfur with dust is characterized by S and a mix of Na, Mg, Al, Si, K, Ca, Ti, and Fe from the medium and large size modes. This study shows that the utilization of time and size resolved DRUM data can assist in the identification of sources and atmospheric processes leading to the observed ambient concentrations.     

Levels of outdoor PM2.5, absorbance and sulphur as surrogates for personal exposures among post-myocardial infarction patients in Barcelona,Spain

Outdoor levels of fine particles (PM_2.5; particles <2.5 μm) have been associated with cardiovascular health. Persons with existing cardiovascular disease have been suggested to be especially vulnerable. It is unclear, how well outdoor concentrations of PM_2.5 and its constituents measured at a central site reflect personal exposures in Southern European countries. The objective of the study was to assess the relationship between outdoor and personal concentrations of PM_2.5, absorbance and sulphur among post-myocardial infarction patients in Barcelona, Spain.Thirty-eight subjects carried personal PM_2.5 monitors for 24-h once a month (2–6 repeated measurements) between November 2003 and June 2004. PM_2.5 was measured also at a central outdoor monitoring site. Light absorbance (a proxy for elemental carbon) and sulphur content of filter samples were determined as markers of combustion originating and long-range transported PM_2.5, respectively.There were 110, 162 and 88 measurements of PM_2.5, absorbance and sulphur, respectively. Levels of outdoor PM_2.5 (median 17 μg m³) were lower than personal PM_2.5 even after excluding days with exposure to environmental tobacco smoke (ETS) (median after exclusion 27 μg m³). However, outdoor concentrations of absorbance and sulphur were similar to personal concentrations after exclusion of ETS. When repeated measurements were taken into account, there was a statistically significant association between personal and outdoor absorbance when adjusting for ETS (slope 0.66, p<0.001), but for PM_2.5 the association was weaker (slope 0.51, p=0.066). Adjustment for ETS had little effect on the respective association of S (slope 0.69, p<0.001).Our results suggest that outdoor measurements of absorbance and sulphur can be used to estimate both the daily variation and levels of personal exposures also in Southern European countries, especially when exposure to ETS has been taken into account. For PM_2.5, indoor sources need to be carefully considered.     

Deposition rates on smooth surfaces and coagulation of aerosol particles inside a test chamber

Because aerosol particle deposition is an important factor in indoor air quality, many empirical and theoretical studies have attempted to understand the process. In this study, we estimated the deposition rate of aerosol particles on smooth aluminum surfaces inside a test chamber. We investigated the influence of turbulent intensity due to ventilation and fan operation. We also investigated two important processes in particle deposition: turbophoresis, which is significant for micron particles, and coagulation, which is relevant to ultrafine particles (UFP diameter <0.1 μm) at high particle concentrations. Our analysis included semi-empirical estimates of the deposition rates that were compared to available deposition models and verified with simulations of an aerosol dynamics model. In agreement with previous studies, this study found that induced turbulent intensity greatly enhanced deposition rates of fine particles (FP diameter <1 μm). The deposition rate of FP was proportional to the ventilation rate, and it increased monotonically with fan speed. With our setup, turbophoresis was very important for coarse particles larger than 5 μm. The coagulation of aerosol particles was insignificant when the particle concentration was less than 10⁴ cm^?3 during fan operation. The model simulation results verified that the aerosol dynamics module incorporated in our Multi-Compartment and Size-Resolved Indoor Aerosol Model (MC-SIAM) was valid. The behavior of aerosol particles inside our chamber was similar to that found in real-life conditions with the same ventilation rates (0.018–0.39 h^?1) and similar air mixing modes. Therefore, our findings provide insight into indoor particle behavior.     

Assessment of metal concentrations in atmospheric particles from Burnaby Lake,British Columbia,Canada

Trace metals were assessed in atmospheric particulates at Burnaby Lake, in the greater Vancouver area of British Columbia to assess concentrations, particle size distributions and deposition rates to an urban watershed. Week-long samples were collected over a period of 18 weeks in 1995 using a 13 stage low pressure impactor (LPI). Samples were analysed using inductively coupled plasma atomic emission spectroscopy (ICP). Aluminum, boron, calcium, iron, magnesium, manganese, sodium and strontium had a similar time series pattern and particle size distribution. For these metals, maximum concentrations occurred during weeks of low precipitation and exhibited a large peak in mid June. Their particle size distribution was mostly dominated by a large peak between 1.7–18.4 μm with a secondary peak at <0.08 μm. Metal concentrations were generally one to three orders of magnitude higher than those measured in a rural location 100 km away from Burnaby Lake but similar to those measured in urban Taipei, Taiwan. Concentrations of the highly toxic metals, arsenic, cadmium and lead were within current air quality guidelines, however boron exceeded the Ontario Ministry of Environment ambient air quality standard in two of the 16 samples. Deposition velocities ranged between 0.22 and 13 cm s⁻¹ with the largest values corresponding to the coarse particle mode. Mean deposition rates ranged between 4.0 μg m⁻² d⁻¹ and 650 mg m⁻² d⁻¹. Depending on the metal, yearly loadings to the watershed ranged from 90 kg to several thousand tonnes. Calcium, aluminum, boron and magnesium had the highest metal loadings to the watershed. Manganese also had relatively high loadings, a reflection of the high traffic density in the area. The relatively high metal deposition rates indicate that metal contribution from atmospheric sources may represent a significant portion of the total metal load to the Burnaby Lake watershed.     

Source and transport of tricresyl phosphate (TCP) isomers in Kurose river basin

Atmospheric tricresyl phosphate (TCP) isomers in Kurose river basin were determined. The concentrations of o-TCP and m-TCP were 0.13 and 0.09 ng m⁻³, respectively, while p-TCP was scarcely detected. Exhaust gases from motorcycles and automobiles were main sources for TCP isomers in the atmosphere. Exhaust gas from incinerator also contributes to atmospheric concentration of TCP isomers. Most of the TCP isomers could be estimated to be sorbed to particles, due to their low vapor pressures. The concentrations of TCP isomers were relatively high in soils collected from an open storage yard of waste PVC and near the highway and greenhouse of agricultural film. On the other hand, the concentrations were negligibly small in soil collected from the forest except for the silt-clay fraction in the soil. Dry deposition fluxes of o-TCP and m-TCP from the atmosphere was 0.2 and 0.04 μg m⁻² d⁻¹, respectively. Wet deposition flux of TCP isomers during one rainfall exceeded occasionally the dry deposition flux for two weeks. TCP isomers accumulated in soil were discharged into river by precipitation event. Their concentrations increased with an increase in river flow, characteristic of a non-point source of TCP isomers.     

Size distribution and sources of trace metals and n-alkanes in the Athens urban aerosol during summer

Size-resolved, 24-h aerosol samples were collected from June–July 2001 by means of an Andersen high-volume cascade impactor. Sampling was conducted in a central avenue (Patission) characterised by heavy traffic, 21 m above street level, in the Athens city centre. Samples were analysed by atomic absorption spectrometry and gas chromatography to determine the size distribution of nine metallic elements (Cd, Pb, V, Ni, Mn, Cr, Cu, Fe, Al) and n-alkanes (with carbon numbers in the range 18–35). The aerosol mass median diameter (MMD) was calculated by means of probit analysis on the cumulative mass concentration size distribution for each metals and n-alkane. The total n-alkane mass concentration (TNA) in total suspended particles (TSP) ranged from 72 to 1506 ng m⁻³ while the total metal concentration ranged from 5.6 to 28.6 μg m⁻³. The results showed that metals such as Cd, V and Ni are characterised by a MMD <1 μm, while the MMD for Pb and Mn are ∼1 μm. Such metals are generally considered to have anthropogenic emission sources. Other metals such as Al, Fe, Cu and Cr were found to have MMD=2–6 μm, which generally originate from soil dust or mechanical abrasion processes. The Carbon number profile of n-alkane compounds showed a strong anthropogenic source with only a minor biogenic influence. The concentration of most n-alkanes was characterised by high variability during the sampling period, in contrast to the concentration of most trace metals. Most n-alkanes had a unimodal size distribution with MMD=1–2 μm similar to those of some trace metals (Pb, Mn), which originate mostly from vehicle emissions. This is a strong indication that these species have a common source. Finally, gas–particle partitioning of n-alkanes was also examined for different particle sizes by means of the relationship between the partition constant K_p and saturation vapour pressure (p_L⁰) as proposed by current sorption models.     

Chemical characteristics of principal PM2.5 species in Chongju,South Korea

Fine particles were collected over four seasons from October 1995 to August 1996 to evaluate the chemical characteristics of principal PM_2.5 components in Chongju, South Korea. The annual mean concentrations of PM_2.5 (d_p⩽2.5 μm), sulfate, nitrate, ammonium, elemental carbon (EC) and organic carbon (OC) were 44.2, 8.22, 3.63, 2.84, 4.44 and 4.99 μg m⁻³, respectively. The sum of the species measured from this study accounted for 50–62% of the PM_2.5 mass. Sulfate was the most abundant species and constituted 13–23% of the PM_2.5 mass. The EC and OC accounted for 17–28% of PM_2.5. The correlation between OC and EC was strong, and the annual mean ratio of OC/EC was 1.12, suggesting that OC measured in the Chongju area may be emitted directly in particulate form as a primary aerosol.     

Dry deposition of sulphur over eastern South Africa

Dry deposition of sulphur is estimated in three climatic regions of Mpumalanga, South Africa, using the inferential method. Data from June 1996 to May 1997 are used at Elandsfontein and Palmer on the industrialised highveld, as well as data from two-week monitoring campaigns in the late-winter and in summer at Blyde on the eastern escarpment and at Skukuza in the lowveld. Total dry deposition rates for sulphur range across the Mpumalanga highveld from 13.1 kg ha^-1 a^-1 at Elandsfontein to 3.1 kg ha^-1 a^-1 at Palmer, are associated with the strong SO₂ gradient between the two stations and are attributed mostly to dry deposition of sulphur from SO₂. The deposition flux varies less from Palmer eastward over the escarpment and the lowveld and ranges from 3.9 kg S ha^-1 a^-1 at Blyde to 3.3 kg S ha^-1 a^-1 at Skukuza. A weak seasonal variation in sulphur dry deposition flux occurs on the central highveld with the maximum in summer and the minimum in winter. Conversely, the maximum sulphur dry deposition on the periphery of the highveld, the escarpment and in the lowveld occurs in winter with the minimum in summer. More than 80% of the dry deposition of sulphur in Mpumalanga occurs during daytime in all seasons.     

Bioaccumulation and uptake routes of perfluoroalkyl acids in Daphnia magna

Perfluoroalkyl acids (PFAs), one kind of emerging contaminants, have attracted great attentions in recent years. However, the study about their bioaccumulation mechanism remains scarce. In this research, the bioaccumulation of six kinds of PFAs in water flea Daphnia magna was studied. The uptake rates of PFAs in D. magna ranged from 178 to 1338 L kg^?1 d^?1, and they increased with increasing perfluoroalkyl chain length; the elimination rates ranged from 0.98 to 2.82 d^?1. The bioaccumulation factors (BAFs) of PFAs ranged from 91 to 380 L kg^?1 in wet weight after 25 d exposure; they increased with increasing perfluoroalkyl chain length and had a significant positive correlation with the n-octanol/water partition coefficients (log K_ow) of PFAs (p < 0.05). This indicated that the hydrophobicity of PFAs plays an important role in their bioaccumulation. The BAFs almost kept constant when the PFA concentrations in aqueous phase increased from 1 to 10 μg L^?1. Scenedesmus subspicatus, as the food of D. magna, did not significantly affect the bioaccumulation of PFAs by D. magna. Furthermore, the body burden of PFAs in the dead D. magna was 1.08–2.52 times higher than that in the living ones, inferring that the body surface sorption is a main uptake route of PFAs in D. magna. This study suggested that the bioaccumulation of PFAs in D. magna is mainly controlled by their partition between organisms and water; further research should be conducted to study the intrinsic mechanisms, especially the roles of protein and lipid in organisms.