A passive flux denuder for evaluating emissions of ammonia at a dairy farm

Passive samplers have been shown to be an inexpensive alternative to direct sampling. Diffusion denuders have been developed to measure the concentration of species such as ammonia (NH3), which is in equilibrium with particulate ammonium nitrate. Conventional denuder sampling has required active sampling that inherently requires air pumps and, therefore, electrical power. To estimate emissions of NH3 from a fugitive source would require an array of active samplers and meteorological measurements to estimate the flux. A recently developed fabric denuder was configured in an open tube to passively sample NH3 flux. Passive and active samplers were collocated at a dairy farm at the California State University, Fresno, Agricultural Research Facility. During this comparison study, NH3 flux measurements were made at the dairy farm lagoon before and after the lagoon underwent acidification. Comparisons were made of the flux measurements obtained directly from the passive flux denuder and those calculated from an active filter pack sampler and wind velocity. The results show significant correlation between the two methods, although a correction factor needed to be applied to directly compare the two techniques. This passive sampling approach significantly reduces the cost and complexity of sampling and has the potential to economically develop a larger inventory base for ambient NH3 emissions.     

Measuring emissions of organophosphate flame retardants using a passive flux sampler

Flame retardants are used in polymers to reduce the flammability of building materials, electric appliances, fabric and papers. In recent years, organophosphate flame retardants have been used as substitutes for polybrominated flame retardants (BFRs). In Japan, the amount of organophosphate flame retardants used in 2001 was about five times more than in 2000. Recently, several studies have shown the health concerns for some organophosphate flame retardants. Little research has been performed on the emission of organophosphate flame retardants, especially the relationship between content and emissions. In this study, a new type of passive sampler was developed to measure emissions of organophosphate flame retardants from plastic materials. With this sampler, emissions from polyvinyl chloride wallpaper samples with different content of tris(2-chloroisopropyl)phosphate (TCPP) at different temperatures were examined. The observed maximum emissions of TCPP from 1, 3, 5, 10 and 20 w/w% content wallpaper materials were 262.3, 452.6, 644.8, 1119.1 and 2166.8 μg m⁻² h⁻¹, respectively. Emissions from 5% TCPP content materials at 40 and 60 °C were 1135.7 and 2841.2 μg m⁻² h⁻¹, respectively. A significantly positive correlation between the flux of TCPP and the TCPP content of the wallpaper samples was observed. A linear relationship was found between the inverse of temperature and the logarithm of TCPP emission. The results imply that the use of materials with a high organophosphate flame retardant content can lead to high emission rates in high-temperature indoor environments.     

The validation of a passive sampler for indoor and outdoor concentrations of volatile organic compounds

Volatile organics compounds (VOCs) are ubiquitous in the air we breathe. The use of passive samplers to measure these concentrations can be an effective technique. When exposed for long durations, a passive sampler may be a good tool for investigating chronic exposures to chemicals in the environment. A passive sampler that was designed for occupational exposures can be used as such a tool. Laboratory validation under as many conditions as possible needs to be accomplished so as to characterize the sampler with known parameters. This paper describes the methods and results of an investigation into the validity of using a passive monitor to sample VOCs for a three-week period. Two concentration levels, two relative humidities, and five VOCs were studied. Results indicate that the samplers work best under conditions of high concentration with low relative humidity and low concentration with high relative humidity. For the passive sampler, excluding chloroform, percent deviations from the predicted values varied between -41 and +22 percent; while the values between the passive and the active samplers varied between -27 and +24 percent. Benzene, heptane, and perchloroethylene were sampled with equal precision and accuracy.     

A study on emission of phthalate esters from plastic materials using a passive flux sampler

Phthalate esters are used as plasticizer in many plastics, and several studies have shown their toxicity. Phthalate esters are gradually emitted over time, and so it is conceivable that they pose a significant health risk. This study aims to investigate the temperature dependence of the emissions of various phthalate esters and to estimate the health risks of these emissions at various temperatures. A passive-type sampler was developed to measure the flux of phthalate esters from the surface of plastic materials. With this sampler, we examined three widely used plastic materials: synthetic leather, wallpaper and vinyl flooring. The observed maximum emissions of diethyl phthalate, dibutyl phthalate, and diethylhexyl phthalate (DEHP) from these materials at 20°C were 0.89, 0.77, and 14 μg m⁻² h⁻¹, respectively. Emissions at 80°C were 2.8, 4.5×10², and 1.5×10³ μg m⁻² h⁻¹, respectively. The results showed this temperature dependence is determined primarily by the type of phthalate ester and less so by the type of material. The estimation from the results of temperature dependence indicated the concentration of DEHP in a vehicle left out in the sunshine during the day can exceed the recommended levels of Japan Ministry of Health, Labour and Welfare.     

Calibration of the Chemcatcher passive sampler for monitoring selected polar and semi-polar pesticides in surface water

Passive sampling is a powerful method for continuous pollution monitoring, but calibration experiments are still needed to generate sampling rates in order to estimate water concentrations for polar compounds. We calibrated the Chemcatcher device with an uncovered SDB-XC Empore disk as receiving phase for 12 polar and semi-polar pesticides in aquatic environments in flow-through tank experiments at two water flow velocities (0.135 m/s and 0.4 m/s). In the 14-day period of exposure the uptake of test substances in the sampler remained linear, and all derived sampling rates R(s) were in the range of 0.1 to 0.5 L/day. By additionally monitoring the release of two preloaded polar pesticides from the SDB-XC disks over time, very high variation in release kinetics was found, which calls into question the applicability of performance reference compounds. Our study expands the applicability of the Chemcatcher for monitoring trace concentrations of pesticides with frequent occurrence in water.     

Preliminary measurements of summer nitric acid and ammonia concentrations in the Lake Tahoe Basin air-shed: implications for dry deposition of atmospheric nitrogen

Over the past 50 years, Lake Tahoe, an alpine lake located in the Sierra Nevada mountains on the border between California and Nevada, has seen a decline in water clarity. With significant urbanization within its borders and major urban areas 130 km upwind of the prevailing synoptic airflow, it is believed the Lake Tahoe Basin is receiving substantial nitrogen (N) input via atmospheric deposition during summer and fall. We present preliminary inferential flux estimates to both lake surface and forest canopy based on empirical measurements of ambient nitric acid (HNO3), ammonia (NH3), and ammonium nitrate (NH4NO3) concentrations, in an effort to identify the major contributors to and ranges of atmospheric dry N deposition to the Lake Tahoe Basin. Total flux from dry deposition ranges from 1.2 to 8.6 kg N ha-1 for the summer and fall dry season and is significantly higher than wet deposition, which ranges from 1.7 to 2.9 kg N ha-1 year-1. These preliminary results suggest that dry deposition of HNO3 is the major source of atmospheric N deposition for the Lake Tahoe Basin, and that overall N deposition is similar in magnitude to deposition reported for sites exposed to moderate N pollution in the southern California mountains.     

Theory and laboratory study of a tall passive chamber for measuring gas fluxes at soil surface

A tall passive flux chamber with a height significantly greater than its horizontal dimensions is proposed for measuring fluxes of volatile organic compounds (VOCs) at the soil surface. The main feature of this tall chamber is the presence of a vertical concentration gradient of the target gas in the chamber. The emission and transport behavior of the target gas in the soil-chamber system are analyzed using the diffusion theory. A mathematical model is developed to estimate the flux from the soil into the tall chamber, providing the target gas establishes a detectable vertical concentration gradient in the chamber. To obtain the data required for calculating flux, only two gas concentrations (C1 and C2) at two heights (h1 and h2) within the chamber need to be measured at the end of a short chamber placement time (tp). To evaluate the applicability of the tall chamber for measuring flux, several laboratory tests have been conducted, using CH2Cl2 and CH3Br as the target gases. The results indicate that the proposed tall chamber has promising potential as a method for measuring fluxes of VOCs at the soil surface.     

Development and calibration of a passive sampler for N-nitrosodimethylamine (NDMA) in water

N-Nitrosamines such as N-nitrosodimethylamine (NDMA) are organic compounds of environmental concern in groundwater, wastewater and potable water due to their potent carcinogenicity in laboratory animal studies and probable human carcinogenicity. While passive sampling techniques have become a widely used tool for providing time-averaged estimates of trace pollutant concentration, for chemicals such as NDMA that have relatively high water solubility, the selection of a suitable sorbent is difficult. This work is a proof of principle study that investigated for the first time the use of coconut charcoal as a passive sampler sorbent. Apparent charcoal/water sorption coefficients for NDMA were >551 mL g⁻¹ at environmentally relevant aqueous concentrations of less than 1 μg L⁻¹. Under the experimental conditions employed, a sampling rate of 0.45 L d⁻¹ was determined and for an aqueous concentration of 1000 ng L⁻¹, it is predicted that the sampler remains in the linear uptake stage for approximately 4 d, while equilibrium attainment would require about 26 d. The presence of humic acid, used as a surrogate for DOC, enhanced NDMA sorption on the coconut charcoal.     

Development of a MnO2-coated,cylindrical denuder for removing NO2 from atmospheric samples

In order to develop a diffusion denuder for the removal of NO₂ from ambient atmospheric samples, a number of materials were screened for their ability to adsorb NO₂:

• 1.(1) MgO;
• 2.(2) MnO₂ on alpha-Al₂O₃;
• 3.(3) water-treated MnO₂ on alpha-Al₂O₃; and
• 4.(4) MnO₂ (activated).

A simple cylindrical denuder coated with MnO₂ (activated) was very effective in the removal of NO₂ from a feedgas of NO₂ in air at ambient temperature and pressure. The other materials were unsatisfactory. The strong oxidizing properties, along with the hydrated surface of the MnO₂ (activated), appear to be important for the sorption of NO₂, as suggested in applications elsewhere. Quantification of denuder sorption efficiencies indicates that MnO2 (activated) is nearly a perfect sorbent for NO₂. The diffusion coefficient of NO₂ in air was found to be 10.8 ± 0.3 cm² min⁻¹ at 22–23°C, which compares favourably with a theoretical estimate. Although MnO₂ (activated)-coated denuders were also found to adsorb SO₂, interference with NO₂ sorption was not sufficient to impair ambient applications.     

Modeling mercury fluxes and concentrations in a Georgia watershed receiving atmospheric deposition load from direct and indirect sources

This paper presents a modeling analysis of airborne mercury (Hg) deposited on the Ochlockonee River watershed located in Georgia. Atmospheric deposition monitoring and source attribution data were used along with simulation models to calculate Hg buildup in the subwatershed soils, its subsequent runoff loading and delivery through the tributaries, and its ultimate fate in the mainstem river. The terrestrial model calculated annual watershed yields for total Hg ranging from 0.7 to 1.1 microg/m2. Results suggest that approximately two-thirds of the atmospherically deposited Hg to the watershed is returned to the atmosphere, 10% is delivered to the river, and the rest is retained in the watershed. A check of the aquatic model results against survey data showed a reasonable agreement. Comparing observed and simulated total and methylmercury concentrations gave root mean square error values of 0.26 and 0.10 ng/L, respectively, in the water column, and 5.9 and 1 ng/g, respectively, in the upper sediment layer. Sensitivity analysis results imply that mercury in the Ochlockonee River is dominated by watershed runoff inputs and not by direct atmospheric deposition, and that methylmercury concentrations in the river are determined mainly by net methylation rates in the watershed, presumably in wetted soils and in the wetlands feeding the river.     

Seasonal variation of atmospheric ammonia and particulate ammonium concentrations in the urban atmosphere of yokohama over a 5-year period

Measurements of ammonia and particulate ammonium were made in the daytime (1200–1500) at a urban site in Yokohama during the 5-year period, 1982–1986. Diurnal NH₃ concentrations showed a distinct seasonal trend with a maximum in summer. The diurnal monthly average concentrations were above 10 ppb during the late spring and summer months, while the concentrations during the winter months were between 1 and 5 ppb. The seasonal variation was found to be very similar to that of the average air temperature and showed a periodic pattern over 1 year. A good correlation was observed between diurnal NH₃ concentrations and average air temperatures during the 5-year period. The annual mean concentrations were in the range of 6.6–7.6 ppb with only a minor deviation. The diurnal monthly average concentrations of particulate NH₄⁺ were between 1 and 4 μg m⁻³ and no significant seasonal variations were seen. As a short-term study, simultaneous measurements of NH₃, HNO₃ and particulate NO₃⁻ were made. The diurnal mean concentrations of NH₃ and HNO₃ were 7.6 and 0.8 ppb, respectively. The concentration of particulate NO₃⁻ ranged from 0.3 to 6μg⁻³. Both HNO₃ and particulate NO₃⁻ concentrations were relatively low and constant. Thus, NH₃ and HNO₃ levels did not agree with the concentrations predicted from the NH₄NO₃ equilibrium constant.     

A passive air sampler for characterizing the vertical concentration profile of gaseous phase polycyclic aromatic hydrocarbons in near soil surface air

Air-soil exchange is an important process governing the fate of polycyclic aromatic hydrocarbons (PAHs). A novel passive air sampler was designed and tested for measuring the vertical concentration profile of 4 low molecular weight PAHs in gaseous phase (PAH_LMW4) in near soil surface air. Air at various heights from 5 to 520 mm above the ground was sampled by polyurethane foam disks held in down-faced cartridges. The samplers were tested at three sites: A: an extremely contaminated site, B: a site near A, and C: a background site on a university campus. Vertical concentration gradients were revealed for PAH_LMW4 within a thin layer close to soil surface at the three sites. PAH concentrations either decreased (Site A) or increased (Sites B and C) with height, suggesting either deposition to or evaporation from soils. The sampler is a useful tool for investigating air-soil exchange of gaseous phase semi-volatile organic chemicals.     

Land-surface exchange in a chemically-reactive system; surface fluxes of HNO3, HCl and NH3

Vertical gradients from 0.25 to 2 m of NH₃, HNO₃ and HCl and associated aerosol components have been measured in the field above various surfaces in eastern England. The data have been examined to identify the effect, if any, of chemical reaction processes upon the observed vertical profiles. It is concluded that chemical transformations are too slow to influence concentration gradients and thus the surface exchange process. Assuming chemically conservative behaviour, deposition velocities for HNO₃ and HCl have been calculated; these lie within the range 0.4–7.7 cms⁻¹ and 0.4–6.9 cms⁻¹ for HNO₃ and HCl, respectively. Estimation of resistances to deposition indicates a negligible surface resistance for both species. Fluxes of ammonia were predominantly upward from the ground with a mean value of 0.031 μg m⁻²s⁻¹ which is consistent both with an emission inventory of the U.K. and with the measured atmospheric concentration of NH₃.     

Field validation of an active sampling cartridge as a passive sampler for long-term carbonyl monitoring

A carbonyl sampler originally designed for the active sampling method (Sep-Pak XPoSure) was used for long-term passive sampling, and its applicability as a passive sampler was examined through field experiments. The uptake rates of passive sampling were determined experimentally from collocated passive and active samplings for various sampling periods. The obtained uptake rates of formaldehyde, acetaldehyde, and acetone were 1.48, 1.23, and 1.08 mL/min, respectively. These uptake rates were consistent for a wide range of the sampling term (12 hr-2 weeks). Uptake rates of each carbonyl were proportional to the diffusion coefficients of each. Therefore, the ratios of diffusion coefficients were used to calculate the uptake rates of carbonyls for which the rates were not determined experimentally. Lower limits of determination were 2.16-17.5 microg/m3 for 2-week sampling. It was confirmed that 2-week monitoring of carbonyl concentrations up to 118-229 microg/m3 was possible. Relative standard deviations of the passive method generated from the repeatability test were 2-12.3% error for five samplings, and the recovery efficiencies were larger than 90%. Thus, the passive sampler was found to be highly suitable for long-term monitoring of carbonyl compounds.     

Radial diffusive sampler for the determination of 8-h ambient ozone concentrations

The 8-h ozone radial diffusive sampler was evaluated according to the CEN protocol for the validation of diffusive samplers. All the parameters regarding the sampler characteristics were found to be consistent with the requirements of this protocol apart from the blank value, which must be evaluated and subtracted at each sampling. The nominal uptake rate was determined in laboratory conditions. However, the uptake rate depends on the mass uptake, temperature, humidity and on the combination of temperature and humidity. Based on laboratory experiments, an empirical model has been established which improved the agreement between the radial sampler and the reference method. This improvement was observed under several different meteorological and emission conditions of sampling. By using the model equation of uptake rate, the data quality objective of 30% for the expanded uncertainty included in the O(3) European Directive, is easily attained. Therefore, the sampler represents an appropriate indicative method.     

Use of passive samplers to measure atmospheric ammonia levels in a high-density industrial hog farm area of eastern North Carolina

Hog concentrated animal feeding operations (CAFOs) in North Carolina release ammonia (NH₃), hydrogen sulfide, VOCs, and particulate matter to the atmosphere. These operations are located mainly in the NC coastal plain and can create potential health hazards for nearby human populations. Limited work has been performed to measure NH₃ at the community level to assess potential human exposure. In an effort to address this issue, a study was designed to measure NH₃ levels near hog CAFOs and community locations (i.e. homes and schools) in Eastern NC.NH₃ was collected using passive diffusion tubes in triplicate exposed primarily in weekly intervals. Sampling occurred from October 2003 to May 2004 (20 sites) and from July 2004 to October 2004 (23 sites) at varying distances from hog CAFOs in close proximity to homes and schools. Average weekly NH3 levels were measured as mass (μg NH₃-N) and converted to concentration (ppb). Mean level of 13.8 ppb near homes and schools (<2 km) was 4–12 times greater than ambient background levels (1–3 ppb), reaching as high as 80 ppb. Exposed sites (<2 km from a hog CAFO) had a mean level of 12.8 ppb which was over 2 times higher than the mean level of 5.5 ppb at less exposed sites (>2 km from a hog CAFO).The study establishes that passive sampling can be effectively used to measure average atmospheric ammonia levels at community locations near hog CAFOs in Eastern NC. The collected data indicate the relative exposure for human populations who live near a hog CAFO. The closer a populace is to the hog CAFO, the more intense the exposure. These results require more validation in the field by comparison to a reference method.     

Calibration of the Chemcatcher passive sampler for the monitoring of priority organic pollutants in water

An integrative passive sampler consisting of a C18 Empore disk receiving phase saturated with n-octanol and fitted with low-density polyethylene diffusion membrane was calibrated for the measurement of time-weighted average concentrations of hydrophobic micropollutants, including polyaromatic hydrocarbons and organochlorine pesticides, in water. The effect of temperature and water turbulence on kinetic and thermodynamic parameters characterising the exchange of analytes between the sampler and water was studied in a flow-through system under controlled conditions. It was found that the absorption of test analytes from water to the sampler is related to their desorption to water. This allows for the in situ calibration of the uptake of pollutants using offload kinetics of performance reference compounds. The sampling kinetics are dependent on temperature, and for most of the tested analytes also on the flow velocity. Sampler-water partition coefficients did not significantly change with temperature.     

A numerical study on the vertical dispersion of passive contaminants from a continuous source in the atmospheric surface layer

A numerical solution of the diffusion equation is obtained for the vertical diffusion from a continuous source. The wind speed profile and the eddy diffusivity in this equation are expressed in terms of the surface-layer similarity relations obtained in the well-known Kansas experiments. A comparison is made with vertical concentration measurements obtained during the Prairie Grass and Porton experiments. The numerical results are in agreement with these experimental data.     

Performance of a thermally desorbable type-tube diffusive sampler for very low air concentrations monitoring

Perkin-Elmer tubes packed with Tenax TA have been tested for the monitoring of low concentrations of aromatic compounds and linear alkanes using diffusive sampling. The uptake rates have been investigated for different exposure doses. A particular hexane and benzene behaviour has been observed: their uptake rates decrease rapidly in the lower exposure doses and so follow an exponential curve. The uptake rates of heavier compounds adopt another tendency: a slow decrease with time following a linear profile. The relative humidity influence has been studied too, and no water perturbation has been recorded.     

Elements of a standard protocol for measurements in the indoor atmospheric environment

Measurements in the indoor atmospheric environment are often performed to test postulated relations between complaints about air quality, etc. and the atmospheric environment. The measurements often fail to confirm the expected causalities even when performed by experienced investigators. As the causality may be multifactorial including factors like technical, chemical, physical, medical, psychological, sociological and economical factors, the planning of measurements has to be multidisciplinary. A corporation of such different disciplines can only be done efficiently if a proper protocol is established. This protocol must cover sampling, analyses and evaluation and should identify the specific aims and specify how they are achieved in cooperation between the investigators. The present paper discusses elements of such a protocol.