Chemical characteristics of free tropospheric aerosols over the Japan Sea coast: aircraft-borne measurements

Atmospheric aerosol particulate matter was directly collected in the free troposphere over the Japan Sea coast between 1992 and 1994 using an aircraft-borne nine-stage cascade impactor (particle size range: 0.1–8 μm). The water-soluble components in the aerosol particulate matter were analyzed by ion chromatography. Particulate sulfate and ammonium were detected in most of the samples and their size distributions showed noticeable peaks below the 1 μm particle size range. Water-soluble calcium (Ca²⁺) was detected in half of the samples; the size distribution showed that the maximum particle size was larger than 1 μm. Highly concentrated Ca²⁺ in larger particles was possibly due to transport of Kosa aerosols from the Asian continent in the free troposphere. The concentration of fine particulate sulfate and ammonium tended to increase whenever Ca²⁺ was detected, which suggests possible mixing of Kosa aerosols and non-Kosa aerosols during long-range transport of air masses containing Kosa particles.     

Source apportionment of time and size resolved ambient particulate matter measured with a rotating DRUM impactor

Ambient particulate chemical composition data acquired from samples collected using a three-stage Davis Rotating-drum Universal-size-cut Monitoring (DRUM) impactor in Detroit, MI, between February and April 2002 were analyzed through the application of a three-way factor analysis model. PM_2.5 (particulate matter ⩽2.5 μm in aerodynamic diameter) was collected by a DRUM impactor with 3-h time resolution and three size modes (2.5 μm>D_p>1.15 μm, 1.15 μm>D_p>0.34 μm and 0.34 μm>D_p>0.1 μm). A novel three-way factor analysis model was applied to these data where the source profiles are a three-way array of size, composition and source while the contributions are a matrix of sample by source. Nine factors were identified: road salt, industrial (Fe+Zn), cloud processed sulfate, two types of metal works, road dust, local sulfate source, sulfur with dust, and homogeneously formed sulfate. Road salt had high concentrations of Na and Cl. Mixed industrial emissions are characterized by Fe and Zn. The cloud processed sulfate had a high concentration of S in the intermediate size mode. The first metal works represented by Fe in all three size modes and by Zn, Ti, Cu, and Mn. The second included a high concentration of small size particle sulfur with intermediate size Fe, Zn, Al, Si, and Ca. Road dust contained Na, Al, Si, S, K, and Fe in the large size mode. The local and homogeneous sulfate factors show high concentrations of S in the smallest size mode, but different time series behavior in their contributions. Sulfur with dust is characterized by S and a mix of Na, Mg, Al, Si, K, Ca, Ti, and Fe from the medium and large size modes. This study shows that the utilization of time and size resolved DRUM data can assist in the identification of sources and atmospheric processes leading to the observed ambient concentrations.     

Characteristic number size distribution of aerosol during Asian dust period in Korea

The size-separated number concentrations of aerosols ranging from 0.3 to 25 μm were observed in Seoul and Anmyon Island in the west coast of Korea during Asian dust period in Spring 1998. During the heavy dust period, the number size distributions of aerosols observed in both places were characterized by decreases in small size<0.5 μm and increase in large size between 1.35 and 10 μm. For particles in this range, there was a good correlation between number concentrations observed in both two places. The number of coarse particles >10 μm showed a distinct diurnal variation without a significant change in amplitude, which was more pronounced in Seoul. It suggests that coarse particles were more affected by local sources. Trajectories back in time showed that the air collected in Korea during dust period originated from desert regions in the central part of China. From these results, it was evident that increased particles in the range of 1.35–10 μm during dust source period represented mineral components, which originated possibly from the dust source regions.     

SPM and fungal spores in the ambient air of west Korea during the Asian dust (Yellow sand) period

The relationship between suspended particulate matter (SPM) and fungal spore was investigated in Seosan, a rural county along the west coast of Korea, in the spring of 2000. SPM concentrations in the air were 199.8 μg m⁻³ in the first Asian dust period (23–24 March), 249.4 μg m⁻³ in the second Asian dust period (7–9 April) and 98.9 μg m⁻³ in the non-Asian dust period (12–16 May), respectively. The majority of the total SPM were composed of coarse particles sized about 5 μm during the two Asian dust periods. Four molds genera grown from airborne fungal spores were identified in colonies grown from SPM samples taken during the Asian dust periods. All the genera found, Fusarium, Aspergillus, Penicillium and Basipetospora, are hyphomycetes in the division Deuteromycota. Morphologically, more diversified mycelia of hyphomycetes were grown on the sample captured from 1.1 to 2.1 μm sized SPM than on the other sized samples gathered in the dust periods. On the other hand, no mold was observed on the sample of 1.1–2.1 μm sized SPM in the non-Asian dust period. From these results, it seems evident that several sorts of fine sized fungal spores were suspended in the atmospheric environment of this study area during Asian dust periods.     

Particulate matter and manganese exposures in Toronto,Canada

Methylcyclopentadienyl manganese tricarbonyl (MMT) is a manganese-based gasoline additive used to enhance automobile performance. MMT has been used in Canadian gasoline for about 20 yr. Because of the potential for increased levels of Mn in particulate matter resulting from automotive exhausts, a large-scale population-based exposure study (∼1000 participant periods) was conducted in Toronto, Canada, to estimate the distribution of 3-day average personal exposures to particulate matter (PM_2.5 and PM₁₀) and Mn. A stratified, three-stage, two-phase probability, longitudinal sample design of the metropolitan population was employed. Residential indoor and outdoor, and ambient levels (at a fixed site and on a roof) of PM_2.5, PM₁₀, and Mn were also measured. Supplementary data on traffic counts, meteorology, MMT levels in gasoline, personal occupations, and activities (e.g. amount of vehicular usage) were collected. Overall precision (%RSD) for analysis of duplicate co-located samples ranged from 2.5 to 5.0% for particulate matter and 3.1 to 5.5% for Mn. The detection limits were 1.47 and 3.45 μg m^-3 for the PM₁₀ and PM_2.5 fractions, respectively, and 5.50 and 1.83 ng m^-3 for Mn in PM₁₀ and PM_2.5, respectively. These low detection limits permitted the reporting of concentrations for >98% of the samples. For PM₁₀, the personal particulate matter levels (median 48.5 μg m^-3) were much higher than either indoor (23.1 μg m^-3) or outdoor levels (23.6 μg m^-3). The median levels for PM_2.5 for personal, indoor, and outdoor were 28.4, 15.4 and 13.2 μg m^-3, respectively. The correlation between PM_2.5 personal exposures and indoor concentrations was high (0.79), while correlations between personal and the outdoor, fixed site and roof site were low (0.16–0.27). Indoor Mn concentration distributions (in PM_2.5 and PM₁₀), unlike particulate matter, exhibited much lower and less variable levels that the corresponding outdoor data. The median personal exposure was 8.0 ng m^-3, compared with 4.7 and 8.6 ng m^-3, respectively, for the indoor and outdoor distributions. The highest correlations occurred for personal vs indoor data (0.56) and for outdoor vs roof site data (0.66), and vs fixed site data (0.56). The concentration of Mn in particulate matter, expressed in ppm (w/w), revealed that the fixed site was the highest, followed by the roof site, outdoor, indoor, and personal. The personal and indoor data showed a statistically significant correlation (0.68) while all other correlations between personal or indoor data and outdoor or fixed-site data were quite small. The low correlations of personal and indoor levels with outdoor levels suggest that different sources in the indoor and outdoor microenvironments produce particle matter with dissimilar composition. The correlation results indicate that neither the roof- nor fixed-site concentrations can adequately predict personal particulate matter or Mn exposures.     

Size distributions of airborne microbes in moisture-damaged and reference school buildings of two construction types

Any risk assessment of moisture-damaged buildings requires an accurate characterization of the factors contributing to the human exposure. In this study, the size distributions of indoor air viable fungi and bacteria and average mean diameters of the most common fungi in school buildings were determined. One special focus was to analyze how the microbial size distributions are affected by the building frame (either wooden or concrete) and moisture damage in the building. The study was performed in 32 school buildings classified as moisture-damaged (index) and non-damaged (reference) schools according to technical building investigations. Sampling for indoor air microbes was carried out using a cascade impactor that collects particles on six stages (range from 0.65 to >7 μm) according to their aerodynamic diameters. Both wooden and concrete schools had their highest fungal levels in the size range of 1.1–4.7 μm. However, the concentrations of fungi in all size classes were higher in wooden schools than in concrete schools. Moisture damage-associated differences in size distribution, in the particle size range of 1.1–2.1 μm, were seen in concrete schools but not in wooden schools. In general, the average geometric mean diameter (d_g,ave) of total viable fungi was smaller in wooden schools than in concrete schools, and smaller in index schools of both construction types than in their reference schools. Variation in particle size, however, by genus was observed. No differences in particle size distributions of viable airborne bacteria were found. Our results on the dependency of the particle size on the building type and presence of moisture damage provide an interesting point to be considered in assessing the complex issue of indoor-related bioaerosol exposures.     

An analysis of seasonal surface dust aerosol concentrations in the western US (2001–2004): Observations and model predictions

Long-term surface observations indicate that soil dust represents over 30% of the annual fine (particle diameter less than 2.5 μm) particulate mass in many areas of the western US; in spring and summer, it represents an even larger fraction. There are numerous dust-producing playas in the western US, but surface dust aerosol concentrations in this region are also influenced by dust of Asian origin. This study examines the seasonality of surface soil dust concentrations at 15 western US sites using observations from the Interagency Monitoring of PROtected Visual Environments (IMPROVE) network from 2001 to 2004. Average soil concentrations in particulate matter less than 10 μm in diameter (PM₁₀) were lowest in winter and peaked during the summer months at these sites; however, episodic higher-concentration events (>10 μg m⁻³) occurred in the spring, the time of maximum Asian dust transport to the western US. Simulated surface dust concentrations from the Navy Aerosol Analysis and Prediction System (NAAPS) suggested that long-range transport from Asia dominates surface dust concentrations in the western US in the spring, and that, although some long-range transport does occur throughout the year (1–2 μg m⁻³), locally generated dust plays a larger role in the region in summer and fall. However, NAAPS simulated some anomalously high concentrations (>50 μg m⁻³) of local dust in the fall and winter months over portions of the western US. Differences between modeled and observed dust concentrations were attributed to overestimation of total observed soil dust concentrations by the assumptions used to convert IMPROVE measurements into PM₁₀ soil concentrations, lack of inhibition of model dust production in snow-covered regions, and lack of seasonal agricultural sources in the model.     

Exposure assessment of air pollutants: a review on spatial heterogeneity and indoor/outdoor/personal exposure to suspended particulate matter,nitrogen dioxide and ozone

This review describes databases of small-scale spatial variations and indoor, outdoor and personal measurements of air pollutants with the main focus on suspended particulate matter, and to a lesser extent, nitrogen dioxide and photochemical pollutants. The basic definitions and concepts of an exposure measurement are introduced as well as some study design considerations and implications of imprecise exposure measurements. Suspended particulate matter is complex with respect to particle size distributions, the chemical composition and its sources. With respect to small-scale spatial variations in urban areas, largest variations occur in the ultrafine (<0.1 μm) and the coarse mode (PM_10–2.5, resuspended dust). Secondary aerosols which contribute to the accumulation mode (0.1–2 μm) show quite homogenous spatial distribution. In general, small-scale spatial variations of PM_2.5 were described to be smaller than the spatial variations of PM₁₀. Recent studies in outdoor air show that ultrafine particle number counts have large spatial variations and that they are not well correlated to mass data. Sources of indoor particles are from outdoors and some specific indoor sources such as smoking and cooking for fine particles or moving of people (resuspension of dust) for coarse particles. The relationships between indoor, outdoor and personal levels are complex. The finer the particle size, the better becomes the correlation between indoor, outdoor and personal levels. Furthermore, correlations between these parameters are better in longitudinal analyses than in cross-sectional analyses. For NO₂ and O₃, the air chemistry is important. Both have considerable small-scale spatial variations within urban areas. In the absence of indoor sources such as gas appliances, NO₂ indoor/outdoor relationships are strong. For ozone, indoor levels are quite small. The study hypothesis largely determines the choice of a specific concept in exposure assessment, i.e. whether personal sampling is needed or if ambient monitoring is sufficient. Careful evaluation of the validity and improvements in precision of an exposure measure reduce error in the measurements and bias in the exposure–effect relationship.     

Nitrate and sulfate in individual Asian dust-storm particles in Beijing,China in Spring of 1995 and 1996

Energy dispersive X-ray analysis of elements and reagent thin-film test of particulate nitrate and sulfate were carried out to examine individual dust particles collected in Beijing during five dust-storm events occurring in spring of 1995 and 1996. Dominant particles were electron-opaque and had irregular shapes during the dust-storm periods, and their size was frequently in the range larger than 1 μm (diameter). Besides, some mineral particles that showed regular cubic shapes were found in the range from 0.1 to 2 μm. Their X-ray spectrums indicated calcium was abundant and little or no other elements with atomic number larger than 11 existed in such particles. They were supposed to be emitted initially from construction sites, and then formed through crystallization in the atmosphere. Their most possible composition was CaO or Ca(OH)₂. It was estimated that 93% of the collected electron-opaque particles are dust particles and the cubic particles in term of number frequency. On reagent films, few dust particles reacted apparently with barium chloride suggesting there was no water-soluble sulfate on the surface of dust particles although X-ray spectrums of about 14.6% of dust particles showed peaks of sulfur. The frequency of nitrate-containing particles in dust particles was 10.8%, which was much smaller than that in mineral particles collected in non-dust-storm periods. These results suggest that almost no sulfate is formed and nitrate is hardly formed on the surface of dust particles during their transport from source areas to Beijing.     

Particulate size distributions and mass measured at a motorway during the BAB II campaign

From 1 May to 25 May 2001, the BAB II campaign was carried out at the motorway BAB (656) near Heidelberg. Atmospheric concentrations of particulate matter and gases were measured together with the meteorological conditions. This paper is focused on the particulate matter measured upwind and downwind from the motorway at ground level. In order to determine the source contribution from the motorway traffic, it was necessary to measure upwind and downwind simultaneously due to variations in background concentrations. The particle number contribution from the motorway was found to be 35,000 particles cm⁻³ for particles with diameters close to 20 nm and 5000 particles cm⁻³ for particles with diameters close to 70 nm. Bimodal size distributions were observed on the downwind side, whereas the upwind side showed unimodal size distributions. For particulate mass, it can be estimated that the contribution from the motorway to the PM₁ concentrations is in a range 0.6–1.3 μg m⁻³ for the chosen measurement sites approximately 60 m from the road at a height of 6 m. The soot measurements showed diurnal variation; however, the upwind downwind difference was not measured. Correlation factors showed good correlation between total particle number and number of particles with diameters below 80 nm, CO and NO. There was no correlation between particle number and PM₁₀, which is due to the observation that particle number was dominated by the 20 nm particles.     

Measurements of fine and ultrafine particles formation in photocopy centers in Taiwan

This study investigates the levels of particulate matter smaller than 2.5 μm (PM_2.5) and some selected volatile organic compounds (VOCs) at 12 photocopy centers in Taiwan from November 2004 to June 2005. The results of BTEXS (benzene, toluene, ethylbenzene, xylenes and styrene) measurements indicated that toluene had the highest concentration in all photocopy centers, while the concentration of the other four compounds varied among the 12 photocopy centers. The average background-corrected eight-hour PM_2.5 in the 12 photocopy centers ranged from 10 to 83 μg m⁻³ with an average of 40 μg m⁻³. The 24-h indoor PM_2.5 at the photocopy centers was estimated and at two photocopy centers exceeded 100 μg m⁻³, the 24-h indoor PM_2.5 guideline recommended by the Taiwan EPA. The ozone level and particle size distribution at another photocopy center were monitored and indicated that the ozone level increased when the photocopying started and the average ozone level at some photocopy centers during business hour may exceed the value (50 ppb) recommended by the Taiwan EPA. The particle size distribution monitored during photocopying indicated that the emitted particles were much smaller than the original toner powders. Additionally, the number concentration of particles that were smaller than 0.5 μm was found to increase during the first hour of photocopying and it increased as the particle size decreased. The ultrafine particle (UFP, <100 nm) dominated the number concentration and the peak concentration appeared at sizes of under 50 nm. A high number concentration of UFP was found with a peak value of 1E+8 particles cm⁻³ during photocopying. The decline of UFP concentration was observed after the first hour and the decline is likely attributable to the surface deposition of charged particles, which are charged primarily by the diffusion charging of corona devices in the photocopier. This study concludes that ozone and UFP concentrations in photocopy centers should be concerned in view of indoor air quality and human health. The corona devices in photocopiers and photocopier-emitted VOCs have the potential to initiate indoor air chemistry during photocopying and result in the formation of UFP.     

Food contamination by C20–C50 mineral paraffins from the atmosphere

Most foods from plant origin usually contain 1–10 mg/kg (dry weight) of non-resolved isomeric alkanes in the range of the n-alkanes C₂₀–C₅₀ which are assumed to be residues from mineral oil products (in addition to the natural paraffins). In edible vegetable oils, concentrations may exceed 100 mg/kg. Since it was suspected that this contamination was mostly of environmental origin, particulate matter from air was analysed for the same range of paraffins. In a road tunnel, around 5 μg/m³ of such paraffins were found, corresponding to about 3% of the fine dust (PM10). The composition corresponded to that found in the particulate matter from the exhaust of diesel engines, which in turn largely corresponded to engine (lubricating) oil. In Swiss cities, the C₂₀–C₅₀ mineral paraffins in the PM10 from ambient air amounted to 0.1–1.5 μg/m³ (about 1% of the dust) and seemed to primarily originate from incomplete combustion of heating and diesel oil, lubricating oil, and road tar debris. On the countryside, the concentrations were around 0.03 μg/m³ (0.3% of the dust). Soil contained 0.5–10 mg/kg of these paraffins. The similarity of the molecular weight (volatility) distribution suggests that the food contamination with paraffins, is mostly from the air. A substantial proportion probably consists of lubricating oil. If this hypothesis is confirmed, measures should be investigated to reduce this contamination.     

Characterization of size-fractionated particulate mercury in Shanghai ambient air

The size-fractionated particulate mercury in ambient air was collected at the top of a university campus building in Shanghai from March 2002 to September 2003. Wet digestion followed by cold vapor atom adsorption spectroscopy (CVAAS) was employed to analyze total particulate mercury concentration. Two-step extraction was performed to differentiate volatile particle-phase mercury (VPM), reactive particle-phase mercury (RPM) and inert particle-phase mercury (IPM). The average concentrations of mercury in PM_1.6, PM₈ and total suspended particle (TSP) were 0.058–0.252, 0.148–0.398 and 0.233–0.529 ng m⁻³, respectively. About 50%–60% of mercury in PM₈ was in PM_1.6, and about 60%–70% of mercury in TSP was in PM₈. Particulate mercury was mainly concentrated on fine particles. The mercury fraction in fine particulate matters (<1.6 μm) was over 4 μg g⁻¹ while 1–2 μg g⁻¹ in TSP. Both were much higher than background values, suggesting that anthropogenic sources are the predominant emission contributors. Seasonal variation indicated that the mercury in TSP in spring was higher than that in summer; however, the mercury in fine particles (<1.6 μm) varied little. The fact that fine particulate mercury (<1.6 μm) was well correlated with sulfate and elemental carbon, but not with fluoride, chloride, nitrate and organic carbon, demonstrates that fine particulate mercury is closely associated with stationary sources and gas–particle transformation. Speciation analysis of mercury showed that VPM fraction decreased with the decrease of particle size, while IPM fraction increased and occupied over 50% in particle <1.6 μm. The detailed species in VPM, RPM and IPM were discussed. Coal burning was estimated to contribute approximately 80% of total atmospheric mercury.     

Wintertime size distribution of polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) in the urban environment: Street- vs rooftop-level measurements

The size distribution of ambient air particles and associated organic pollutants, such as polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs), and organochlorine pesticides (OCPs) including hexachlorocyclohexanes (HCHs), DDT and metabolites, etc., was investigated at a traffic-impacted site of Thessaloniki, Greece. Investigation took place during wintertime of 2006 at two heights above ground: at the street level (1.5 m) and at the rooftop level (15 m). Size-resolved samples (<0.95 μm, 0.95–1.5 μm, 1.5–3 μm, 3–7.5 μm and >7.5 μm) were concurrently collected from the two height levels using five-stage high volume cascade impactors. At both heights, particle mass exhibited bimodal distribution with peaks in the 0.95–1.5 μm and the 3–7.5 μm size fractions, whereas most organic pollutants exhibited one peak at 0.95–1.5 μm. Apart from the 0.95–1.5 μm fraction, particle concentrations of all size ranges were significantly higher at the street level than at the rooftop as a result of more intensive vehicular emissions and road dust resuspension. On the contrary, the concentrations of most organic pollutants did not differentiate significantly between the two elevations.     

Indoor exposure from building materials: A field study

The present study has been conducted in the frame of BUMA (Prioritization of Building Materials Emissions as indoor pollution sources), a European funded project, aiming at assessing the exposure to emitted compounds in indoor air. Field campaigns in five (5) European cities (Milan, Copenhagen, Dublin, Athens and Nicosia) were carried out. These campaigns covered weekly winter and summer concentration measurements in two (2) public buildings and two (2) private houses in each city. BTEX, terpenes, and carbonyls were measured using passive sampling in two sites inside the building and one outside. VOC emission measurements on selected building material have also been performed using Field and Laboratory Emission Cell (FLEC). The results on indoor concentrations for compounds such as formaldehyde (1.2–62.6 μg m^?3), acetaldehyde (0.7–41.6 μg m^?3), toluene (0.9–163.5 μg m^?3), xylenes (0.2–177.5 μg m^?3) and acetone (2.8–308.8 μg m^?3) have shown diversity and relatively significant indoor sources depending on the building type, age etc. Indoor concentrations of these substances are varied depending on the building age and type. The percentage of approximately 40% of the indoor air quality levels originated from building materials.     

Particle size and time of the day influences on the morphology distributions of atmospheric fine particles at the Baltimore supersite

The morphology of size-classified ambient particulate matter less than 2.5 μm in aerodynamic diameter (PM_2.5) was studied in samples collected at the USEPA supersite located in Baltimore, MD. Size classification was accomplished through the use of a low pressure impactor to produce samples with cut-off diameters of 0.10, 0.15, 0.55, and 2.0 μm. Sampling was conducted in two campaigns during the fall of 2002, with separate sampling occurring during early morning, mid-day, late afternoon, and evening periods. Particles with cut-off diameters of 2 μm were generally round in shape, with a border fractal dimension close to 1 based on the analysis of transmission electron microscope (TEM) images of collected samples. Particles with a cut-off diameter of 0.15 μm had on average higher fractal dimensions than the other size classes considered, regardless of time of day associated with the sample. As expected, the time of the day influenced the shape of particle populations sampled. Particles collected during early morning were found to have higher fractal dimension than those collected at other sampling times. At night, particles presented mostly round shapes. This difference was particularly pronounced in particles with cut-off diameters of 0.15 μm.     

Particulate matter in the indoor air of classrooms—exploratory results from Munich and surrounding area

Numerous epidemiological studies have demonstrated the association between particle mass (PM) concentration in outside air and the occurrence of health related problems and/or diseases. However, much less is known about indoor PM concentrations and associated health risks. In particular, data are needed on air quality in schools, since children are assumed to be more vulnerable to health hazards and spend a large part of their time in classrooms.On this background, we evaluated indoor air quality in 64 schools in the city of Munich and a neighbouring district outside the city boundary. In winter 2004–2005 in 92 classrooms, and in summer 2005 in 75 classrooms, data on indoor air climate parameters (temperature, relative humidity), carbon dioxide (CO₂) and various dust particle fractions (PM₁₀, PM_2.5) were collected; for the latter both gravimetrical and continuous measurements by laser aerosol spectrometer (LAS) were implemented. In the summer period, the particle number concentration (PNC), was determined using a scanning mobility particle sizer (SMPS). Additionally, data on room and building characteristics were collected by use of a standardized form. Only data collected during teaching hours were considered in analysis. For continuously measured parameters the daily median was used to describe the exposure level in a classroom.The median indoor CO₂ concentration in a classroom was 1603 ppm in winter and 405 ppm in summer. With LAS in winter, median PM concentrations of 19.8 μg m⁻³ (PM_2.5) and 91.5 μg m⁻³ (PM₁₀) were observed, in summer PM concentrations were significantly reduced (median PM_2.5=12.7 μg m⁻³, median PM₁₀=64.9 μg m⁻³). PM_2.5 concentrations determined by the gravimetric method were in general higher (median in winter: 36.7 μg m⁻³, median in summer: 20.2 μg m⁻³) but correlated strongly with the LAS-measured results. In explorative analysis, we identified a significant increase of LAS-measured PM_2.5 by 1.7 μg m⁻³ per increase in humidity by 10%, by 0.5 μg m⁻³ per increase in CO₂ indoor concentration by 100 ppm, and a decrease by 2.8 μg m⁻³ in 5–7th grade classes and by 7.3 μg m⁻³ in class 8–11 compared to 1–4th class. During the winter period, the associations were stronger regarding class level, reverse regarding humidity (a decrease by 6.4 μg m⁻³ per increase in 10% humidity) and absent regarding CO₂ indoor concentration. The median PNC measured in 36 classrooms ranged between 2622 and 12,145 particles cm⁻³ (median: 5660 particles cm⁻³).The results clearly show that exposure to particulate matter in school is high. The increased PM concentrations in winter and their correlation with high CO₂ concentrations indicate that inadequate ventilation plays a major role in the establishment of poor indoor air quality. Additionally, the increased PM concentration in low level classes and in rooms with high number of pupils suggest that the physical activity of pupils, which is assumed to be more pronounced in younger children, contributes to a constant process of resuspension of sedimented particles. Further investigations are necessary to increase knowledge on predictors of PM concentration, to assess the toxic potential of indoor particles and to develop and test strategies how to ensure improved indoor air quality in schools.     

Size distribution of metals in urban aerosols in Seville (Spain)

The size distribution of metals in aerosols has been studied in 12 areas of the city of Seville. Urban particles were collected with a high-volume sampling system equipped with a cascade impactor, which effectively separates the particulate matter into six-size ranges. Forty-one samples were collected in spring 1996. Each filter was extracted with a mixture of nitric and percloric acids. The acid solutions of the samples were analysed in six-particle fractions by inductively coupled plasma atomic emission spectrometry (ICP-AES). The impactor stage fractionation of particles shows a typical bimodal distributions, one corresponding to the fine mode below 1 μm (55%), and the other to the coarse mode around 10 μm (32%). With regard to the size distribution of metals, we concluded that potentially toxic metals, such as nickel, lead and cadmium are mainly accumulated in the smaller particles, with percentages of 72.6, 69.4 and 63.8%, respectively. Lead have a concentration of 63.7 ng m⁻³, more than copper and manganese (26.7 and 16.5 ng m⁻³) and above all more than nickel, cobalt and cadmium (1.97, 0.54 and 0.32 ng m⁻³).     

Fine,ultrafine and nanoparticle trace element compositions near a major freeway with a high heavy-duty diesel fraction

Trace elements and metals in the ultrafine (<0.18 μm) and accumulation (0.18–2.5 μm) particulate matter (PM) modes were measured during the winter season, next to a busy Southern California freeway with significant (∼20%) diesel traffic. Both ambient and concentrated size-segregated impactor samples were taken in order to collect enough mass for chemical analysis. Data at this location were compared to a site located 1 mile downwind of the freeway, which was reflective of urban background. The most abundant trace elements in the accumulation mode detected by inductively coupled plasma mass spectroscopy (ICPMS) were S (138 ng m⁻³), Na (129 ng m⁻³), and Fe (89 ng m⁻³) while S (35 ng m⁻³) and Fe (35 ng m⁻³) were the most abundant in the ultrafine mode. The concentrations of several trace elements, including Mg, Al, and Zn, and in particular Ca, Cu, and Pb, did not uniformly increase with size within fine PM, an indication that various roadway sources exist for these elements. Calculation of crustal enrichment factors for the two sites indicates that the freeway traffic contributed to enriched levels of ultrafine Cu, Ba, P and Fe and possibly Ca. The results of this study show that trace elements constitute a small fraction of PM mass in the nanoparticle size range, but these can and should be characterized due to their likely importance to human health.     

Size and seasonal distributions of airborne bioaerosols in commuting trains

Aerobiological studies in commuting trains in northern Taiwan were carried out from August, 2007 until July, 2008. Two six-stage (>7 μm, 4.7～7 μm, 3.3～4.7 μm, 2.1～3.3 μm, 1.1～2.1 μm, 0.65～1.1 μm) cascade impactors of 400 orifices were used to collect viable bacteria and fungi, respectively. The levels of carbon monoxide (CO), carbon dioxide (CO₂), formaldehyde (HCHO), temperature, and relative humidity in the commuting trains were also recorded during the sampling period. Results show that bacterial concentrations ranged from 25 to 1530 CFU m^?3, and averaged 417 CFU m^?3. The fungal concentrations ranged from 45 to 1906 CFU m^?3, and averaged 413 CFU m^?3. Additionally, the highest fractions occurred in the fifth stage (1.1～2.1 μm) for both bacteria and fungi. The respirable fractions, R_b and R_f, for bacteria and fungi were 62.8% and 81.4%, respectively, which are higher than those in other studies. Furthermore, the bacterial concentration reached its highest level in autumn, and its lowest level in winter. However, the fungal concentration was highest in spring and lowest in winter. Though the total bacterial or fungal concentration did not exceed the recommendation standard in Taiwan, the relatively high respirable fraction in commuting trains probably implies a higher adverse health risk for sensitive commuters. This study further conducted multiple regression analysis to determine the relationship of various stage fractions of airborne bacteria and fungi with indoor air pollutants (CO and HCHO) and environmental parameters (CO₂, temperature, and relative humidity). The correlation coefficients of multiple regression analysis for total bacteria and fungi concentrations with indoor air pollutants and environmental parameters were 0.707 (p < 0.00376) and 0.612 (p < 0.00471), respectively. There are currently no formally regulated laws for indoor air quality (IAQ) in Taiwan, and this preliminary study can provide references to the Taiwan government on IAQ management.