Production of carbon dioxide in a fattening pig house under field conditions. II. Release from the manure

Carbon dioxide (CO₂) release from manure was investigated under field conditions in one of the compartments in a mechanically ventilated fattening pig house. The potential of CO₂ release was tested in the emptied compartment by imposing high ventilation rate and measuring CO₂ concentrations in the incoming and exhaust air. When the compartment was filled with pigs, a model of tranquil CO₂ exhalation rate (TCER) was used to estimate the part of CO₂ produced by animals, in addition to the measurement of CO₂ concentrations and ventilation rate. Useful data were extracted from 135 days of continuously measured field data obtained when the housing system was in steady-state. The CO₂ release per m² of pit surface was 18.4 and 25.8 g h⁻¹ m⁻² in the emptied pig compartment during the impulse and pulse ventilation rate tests, respectively. It ranged from 1.1 and 116.7 g h⁻¹ m⁻² and averaged 42.1 g h⁻¹ m⁻² during the 135-day continuous field measurement. In 128 of the 135 days when the compartment was filled with pigs, the mean CO₂ release from the manure reached an average of 37.5% of the TCER by pigs, instead of less than 5% believed by many researchers. The maximum CO₂ release rate in 2-h steady-state measurements was 94% of the TCER by pigs. This research demonstrated that, in the previous knowledge, there might be a serious underestimation of the CO₂ release from the manure in pig houses. The total pig weight, manure temperature and ventilation rate were found the most important variables related to the CO₂ release. A mathematical model was developed to estimate the CO₂ release as a function of these three variables with R²=0.525.     

Air–land exchanges of CO2, CH4 and N2O measured by FTIR spectrometry and micrometeorological techniques

Micrometeorological flux-gradient and nocturnal boundary layer methods were combined with Fourier transform infrared (FTIR) spectroscopy for high-precision trace gas analysis to measure fluxes of the trace gases CO₂, CH₄ and N₂O between agricultural fields and the atmosphere. The FTIR measurements were fully automated and routinely obtained a precision of 0.1–0.2% for several weeks during a measurement campaign in October 1995. In flux-gradient measurements, vertical profiles of the trace gases were measured every 30 min from the ground to 22 m. When combined with independent micrometeorological measurements of water vapour fluxes, trace gas fluxes from the underlying surface could be determined. In the nocturnal boundary layer method the rate of change in mass storage in the 0–22 m layer was combined with fluxes measured at 22 m to estimate surface fluxes. Daytime fluxes for CO₂ were −0.78±0.40 (1σ) mg CO₂ m⁻² s⁻¹. Daytime fluxes of N₂O and CH₄ were very small and difficult to measure reliably using the flux-gradient technique, despite the high precision of the concentration measurements. Mean daytime flux for N₂O was 17±48 ng N m⁻² s⁻¹, while the corresponding flux for CH₄ was 47±410 ng CH₄ m⁻² s⁻¹. The mean nighttime flux of CO₂ estimated using the nocturnal boundary layer method was +0.15±0.05 mg CO₂ m⁻² s⁻¹, in good agreement with chamber measurements of respiration rates. Nighttime fluxes of CH₄ and N₂O from the nocturnal boundary layer method were 109±69 ng CH₄ m⁻² s⁻¹ and 2±3.2 ng N m⁻² s⁻¹, respectively, in good agreement with chamber measurements and inventory estimates based on the sheep and cattle stocking rates in the region. The suitability of FTIR-based methods for long term monitoring of spatially and temporally averaged flux measurements is discussed.     

Estimate of total CO2 output from desertified sandy land in China

Soil is an important factor in regional and global carbon budgets because it serves as a reservoir of large amount of organic carbon. In our study, using remote sensing data of different periods we analyzed the development and reversion of desertification in China, calculated the variations of organic carbon contents of the desertified lands in China. The results showed that the total storage of organic carbon in 0–50 cm soil layer of the desertified lands is 855 Mt. In recent 40 yr, the total CO₂ amount released by land desertification processes to the atmosphere was 150 Mt, while the CO₂ amount sequestered by desertification reversing processes corresponded to 59 Mt C. Hence, the net CO₂ amount released from desertified lands of China corresponded to 91 Mt C, about 68.42% of the 133 Mt C of annual CO₂ release in the global temperate and frigid zones. Simultaneously, it indicated that CO₂ amount sequestered by desertification reversing processes in desertified land had greater potential than the other soils.     

Greenhouse gas emissions from penguin guanos and ornithogenic soils in coastal Antarctica: Effects of freezing–thawing cycles

In coastal Antarctica, freezing and thawing influence many physical, chemical and biological processes for ice-free tundra ecosystems, including the production of greenhouse gases (GHGs). In this study, penguin guanos and ornithogenic soil cores were collected from four penguin colonies and one seal colony in coastal Antarctica, and experimentally subjected to three freezing–thawing cycles (FTCs) under ambient air and under N₂. We investigated the effects of FTCs on the emissions of three GHGs including nitrous oxide (N₂O), carbon dioxide (CO₂) and methane (CH₄). The GHG emission rates were extremely low in frozen penguin guanos or ornithogenic soils. However, there was a fast increase in the emission rates of three GHGs following thawing. During FTCs, cumulative N₂O emissions from ornithogenic soils were greatly higher than those from penguin guanos under ambient air or under N₂. The highest N₂O cumulative emission of 138.24 μg N₂O–N kg^?1 was observed from seal colony soils. Cumulative CO₂ and CH₄ emissions from penguin guanos were one to three orders of magnitude higher than those from ornithogenic soils. The highest cumulative CO₂ (433.0 mgCO₂–C kg^?1) and CH₄ (2.9 mgCH₄–C kg^?1) emissions occurred in emperor penguin guanos. Penguin guano was a stronger emitter for CH₄ and CO₂ while ornithogenic soil was a stronger emitter for N₂O during FTCs. CO₂ and CH₄ fluxes had a correlation with total organic carbon (TOC) and soil/guano moisture (M_c) in penguin guanos and ornithogenic soils. The specific CO₂–C production rate (CO₂–C/TOC) indicated that the bioavailability of TOC was markedly larger in penguin guanos than in ornithogenic soils during FTCs. This study showed that FTC-released organic C and N from sea animal excreta may play a significant role in FTC-related GHG emissions, which may account for a large proportion of annual fluxes from tundra ecosystems in coastal Antarctica.     

Seasonal soil and leaf CO2 exchange rates in a Mediterranean holm oak forest and their responses to drought conditions

We measured the soil and leaf CO₂ exchange in Quercus ilex and Phillyrea latifolia seasonally throughout the year in a representative site of the Mediterranean region, a natural holm oak forest growing in the Prades Mountains in southeastern Catalonia. In the wet seasons (spring and autumn), we experimentally decreased soil moisture by 30%, by excluding rainfall and water runoff in 12 plots, 1×10 m, and left 12 further plots as controls. Our aim was to predict the response of these gas exchanges to the drought forecasted for the next decades for this region by GCM and ecophysiological models.Annual average soil CO₂ exchange rate was 2.27±0.27 μmol CO₂ m⁻² s⁻¹. Annual average leaf CO₂ exchange rates were 8±1 and 5±1 μmol m⁻² s⁻¹ in Q. ilex and P. latifolia, respectively. Soil respiration rates in control treatments followed a seasonal pattern similar to photosynthetic activity. They reached maximum values in spring and autumn (2.5–3.8 μmol m⁻² s⁻¹ soil CO₂ emission rates and 7–15 μmol m⁻² s⁻¹ net photosynthetic rates) and minimum values (almost 0 for both variables) in summer, showing that soil moisture was the most important factor driving the soil microbial activity and the photosynthetic activity of plants. In autumn, drought treatment strongly decreased net photosynthesis rates and stomatal conductance of Q. ilex by 44% and 53%, respectively. Soil respiration was also reduced by 43% under drought treatment in the wet seasons. In summer there were larger soil CO₂ emissions in drought plots than in control plots, probably driven by autotrophic (roots) metabolism. The results indicate that leaf and soil CO₂ exchange may be strongly reduced (by ca. 44%) by the predicted decreases of soil water availability in the next decades. Long-term studies are needed to confirm these predictions or to find out possible acclimation of those processes.     

Definition of yearly emission factor of dust and greenhouse gases through continuous measurements in swine husbandry

The object of this study was to develop an accurate estimation method to evaluate the contribution of the various compartments of swine husbandry to dust and GHG (greenhouse gases, CO₂, CH₄ and N₂O) emission into the atmosphere during one year of observation.A weaning, a gestation, a farrowing and a fattening room in an intensive pig house were observed in three different periods (Autumn–Winter, Springtime and Summer, monitoring at least 60% of each period (20% at the beginning, in the middle and at the end) of each cycle).During monitoring, live weight, average live weight gain, number of animals and its variation, type of feed and feeding time were taken into account to evaluate their influence on PM₁₀, or the fraction of suspended particulate matter with an aerodynamic diameter less than or equal to 10 μm [Emission Inventory Guidebook, 2007. B1100 Particle Emissions from Animal Husbandry Activities. Available from: <http://reports.eea.europa.eu/EMEPCORINAIR5/en/B1100vs1.pdf> (accessed October 2008)] and to define GHG emission.The selected piggery had a ventilation control system using a free running impeller to monitor continuously real-time environmental and management parameters with an accuracy of 5%.PM₁₀ concentration was monitored by a sampler (Haz Dust EPAM 5000), either continuously or through traditional gravimetric technique, and the mean value of dust amount collected on the membranes was utilized as a correction factor to be applied to continuously collected data.PM₁₀ concentration amount incoming from inlets was removed from PM₁₀ emission calculation, to estimate the real contribution of pig house dust pollution into atmosphere.Mean yearly emission factor of PM₁₀ was measured in 2 g d^?1 LU^?1 for the weaning room, 0.09 g d^?1 LU^?1 for the farrowing room, 2.59 g d^?1 LU^?1 for the fattening room and 1.23 g d^?1 LU^?1 for the gestation room. The highest PM₁₀ concentration and emission per LU was recorded in the fattening compartment while the lowest value was recorded in the farrowing room.CO₂, CH₄ and N₂O concentrations were continuously measured in the exhaust ducts using an infrared photoacoustic detector IPD (Brüel & Kjaer, Multi-gas Monitor Type 1302, Multipoint Sampler and Doser Type 1303) sampling data every 15 min, for the 60% of the cycles.Yearly emission factor for CO₂ was measured in 5997 g d^?1 LU^?1 for the weaning room, 1278 g d^?1 LU^?1 for the farrowing room, 13,636 g d^?1 LU^?1 for the fattening room and 8851 g d^?1 LU^?1 for the gestation room.Yearly emission factor for CH₄ was measured in 24.57 g d^?1 LU^?1 for the weaning room, 4.68 g d^?1 LU^?1 for the farrowing room, 189.82 g d^?1 LU^?1 for the fattening room and 132.12 g d^?1 LU^?1 for the gestation room.Yearly emission factor for N₂O was measured in 3.62 g d^?1 LU^?1 for the weaning room, 0.66 g d^?1 LU^?1 for the farrowing room, 3.26 g d^?1 LU^?1 for the fattening room and 2.72 g d^?1 LU^?1 for the gestation room.     

Rapid measurements and mapping of tracer gas concentrations in a large indoor space

Rapid mapping of gas concentrations in air benefits studies of atmospheric phenomena ranging from pollutant dispersion to surface layer meteorology. Here we demonstrate a technique that combines multiple-open-path tunable-diode-laser spectroscopy and computed tomography to map tracer gas concentrations with approximately 0.5 m spatial and 7 s temporal resolution. Releasing CH₄ as a tracer gas in a large (7 m×9 m×11 m high) ventilated chamber, we measured path-integrated CH₄ concentrations over a planar array of 28 “long” (2–10 m) optical paths, recording a complete sequence of measurements every 7 s during the course of hour-long experiments. Maps of CH₄ concentration were reconstructed from the long path data using a computed tomography algorithm that employed simulated annealing to search for a best fit solution. The reconstructed maps were compared with simultaneous measurements from 28 “short” (0.5 m) optical paths located in the same measurement plane. On average, the reconstructed maps capture ∼74% of the variance in the short path measurements. The accuracy of the reconstructed maps is limited, in large part, by the number of optical paths and the time required for the measurement. Straightforward enhancements to the instrumentation will allow rapid mapping of three-dimensional gas concentrations in indoor and outdoor air, with sub-second temporal resolution.     

Biomass consumption and CO2, CO and main hydrocarbon gas emissions in an Amazonian forest clearing fire

Biomass consumption and CO₂, CO and hydrocarbon gas emissions in an Amazonian forest clearing fire are presented and discussed. The experiment was conducted in the arc of deforestation, near the city of Alta Floresta, state of Mato Grosso, Brazil. The average carbon content of dry biomass was 48% and the estimated average moisture content of fresh biomass was 42% on wet weight basis. The fresh biomass and the amount of carbon on the ground before burning were estimated as 528 t ha^?1 and 147 t ha^?1, respectively. The overall biomass consumption for the experiment was estimated as 23.9%. A series of experiment in the same region resulted in average efficiency of 40% for areas of same size and 50% for larger areas. The lower efficiency obtained in the burn reported here occurred possibly due to rain before the experiment. Excess mixing ratios were measured for CO₂, CO, CH₄, C₂–C₃ aliphatic hydrocarbons, and PM_2.5. Excess mixing ratios of CH₄ and C₂–C₃ hydrocarbons were linearly correlated with those of CO. The average emission factors of CO₂, CO, CH₄, NMHC, and PM_2.5 were 1,599, 111.3, 9.2, 5.6, and 4.8 g kg^?1 of burned dry biomass, respectively. One hectare of burned forest released about 117,000 kg of CO₂, 8100 kg of CO, 675 kg of CH₄, 407 kg of NMHC and 354 kg of PM_2.5.     

Characteristics influencing the variability of urban CO2 fluxes in Melbourne,Australia

Urban areas are significant contributors to global carbon dioxide emissions. Vehicle emissions and other anthropogenic related activities are a frequent source of CO₂ to the atmosphere, contributing to global warming. Micrometeorological techniques used for observations in Northern Hemisphere cities have found that urban CO₂ fluxes are consistently a source. This study investigates CO₂ fluxes in an Australian city, adding to the global database of CO₂ fluxes in a bid to aid in future development of planning policies concerning reductions in CO₂ emissions. Using the eddy covariance approach, fluxes of CO₂ were measured at a suburban site (Preston) in Melbourne, Australia from February 2004 to June 2005 to investigate temporal variability. A second site (Surrey Hills) with differing surface characteristics (in particular, greater vegetation cover) was also established in Melbourne and ran simultaneously for 6 months (February 2004–July 2004). Results showed that both sites were a net source of CO₂ to the atmosphere. Diurnal patterns of fluxes were largely influenced by traffic volumes, with two distinct peaks occurring at the morning and evening traffic peak hours, with the winter morning peak averaging 10.9 μmol m⁻² s⁻¹ at Preston. Summer time fluxes were lower than during winter due to greater vegetative influence and reduced natural gas combustion. Vegetation limited the source of CO₂ in the afternoon, yet was not enough to combat the strong local anthropogenic emissions. Surrey Hills showed higher fluxes of CO₂ despite greater vegetation cover because of higher local traffic volumes. Annual emissions from Preston were estimated at 84.9 t CO₂ ha⁻¹ yr⁻¹. Magnitudes and patterns of suburban CO₂ fluxes in Melbourne were similar to those observed in Northern Hemisphere suburban areas.     

The estimation of historical CO2 trajectories is indeterminate: Comment on “A new look at atmospheric carbon dioxide”

A paper by Hofmann et al. (2009, this journal) is critiqued. It is shown that their exponential model for characterizing CO₂ trajectories for historical data is not estimated properly. An exponential model is properly estimated and is shown to fit over the entire 51 year period of available data. Further, the entire problem of estimating models for the CO₂ historical data is shown to be ill-posed because alternate model forms fit the data equally well. To illustrate this point the past 51 years of CO₂ data were analyzed using three different time-dependent models that capture the historical pattern of CO₂ increase. All three fit with R² > 0.98, are visually indistinguishable when overlaid, and match each other during the calibration period with R² > 0.999. Projecting the models forward to 2100, the exponential model comes quite close to the Intergovernmental Panel on Climate Change (IPCC) best estimate of 836 ppmv. The other two models project values far below the IPCC low estimates. The problem of characterizing historical CO₂ levels is thus indeterminate, because multiple models fit the data equally well but forecast very different future trajectories.     

Radon exhalation and ultrafine fraction of radon progeny in closed room air

The influence of ²²²Rn exhalation from walls and air exchange (low ventilation rates ν<0.3 h^-1) upon its concentration in room air has been considered. It was found that the radon concentration reachs 84 Bq m^-3 at exhalation and ventilation rates of 66 Bq hm^-2 and 0.28 h^-1, respectively. The radon concentration and the ultrafine fraction f_p of potential α energy concentration as well as the equilibrium factor F of the short-lived radon progeny were also determined in three different completely closed rooms. An electroprecipitation method was applied for determining the ²²²Rn concentration while a single wire-screen technique was used for the determination of ultrafine radon progeny. During the measurements, the radon concentrations were varied between 33 and 134 with a mean value 89 Bq m^-3. A mean ultrafine fraction (f_p) of 0.16 was obtained at a mean aerosol particle concentration (Z) of 1700 cm^-3 and a mean equilibrium factor (F) of 0.33. The obtained mean value of f_p was found to be about five times higher than the value reported in the ICRP publication (f_p=0.03). The attachment rate (X), the deposition rate (q^f) and the deposition velocity (v^f_d) of the ultrafine radionuclide ²¹⁸Po were calculated. A mean value of X was found to be 49 h^-1 at a mean q^f of 46 h^-1 and a mean v^f_d of 4.6 m h^-1. The attachment coefficient β of ²¹⁸Po was found to vary between 0.016 and 0.047 with a mean value 0.028 cm³ h^-1.     

Anaerobic abiotic transformations of cis-1,2-dichloroethene in fractured sandstone

A fractured sandstone aquifer at an industrial site is contaminated with trichloroethene to depths greater than 244 m. Field data indicate that trichloroethene is undergoing reduction to cis-1,2-dichloroethene (cDCE); vinyl chloride and ethene are present at much lower concentrations. Transformation of cDCE by pathways other than reductive dechlorination (abiotic and/or biotic) is of interest. Pyrite, which has been linked to abiotic transformation of chlorinated ethenes, is present at varying levels in the sandstone. To evaluate the possible role of pyrite in transforming cDCE, microcosms were prepared with groundwater, ～40 mg L^?1 cDCE + [¹⁴C]cDCE, and crushed solids (pure pyrite, pyrite-rich sandstone, or typical sandstone). During 120 d of incubation, the highest level of cDCE transformation occurred with typical sandstone (11–14% ¹⁴CO₂, 1–3% ¹⁴C-soluble products), followed by pyrite-rich sandstone (2–4% ¹⁴CO₂, 1% ¹⁴C-soluble products) and even lesser amounts with pure pyrite. These results indicate pyrite is not likely the mineral involved in transforming cDCE. A separate experiment using only typical sandstone compared the rate of cDCE transformation in non-sterilized, autoclaved, and propylene-oxide sterilized treatments, with pseudo-first order rate constants of 8.7, 5.4, and 1.0 yr^?1, respectively; however, transformation stopped after several months of incubation. Autoclaving increased the volume of pores, adsorption pore diameter, and surface area in comparison to non-sterilized typical sandstone. Nevertheless, autoclaving was less disruptive than chemical sterilization. The results provide definitive experimental evidence that cDCE undergoes anaerobic abiotic and biotic transformation in typical sandstone, with formation of CO₂ and soluble products.     

Aircraft-based volatile organic compounds flux measurements with relaxed eddy accumulation

Regional estimates of fluxes of volatile organic compounds (VOCs) are required to improve our understanding of their role in the chemistry of the atmosphere. Flux measurements on such a scale can best be obtained using aircraft-based systems. These systems usually rely on the eddy covariance technique, which requires fast response gas sensors for flux measurement, but such sensors are not available for most organic compounds, therefore, the relaxed eddy-accumulation (REA) technique was selected. An aircraft-based REA sampling system was developed and used to measure isoprene emission over the boreal forest during the 1996 summer. Over a short period in July at the Boreal Ecosystem/Atmosphere Study (BOREAS) southern study area (SSA), the isoprene fluxes ranged from −0.06 to 1.79 μg m^-2 s^-1, with a mean of 0.59±0.34 μg m^-2 s^-1, while in August at the BOREAS northern study area (NSA) the isoprene fluxes ranged from 0.00 to 0.26 μg m^-2 s^-1, with a mean of 0.14±0.09 μg m^-2 s^-1. In the SSA, the isoprene fluxes over aspen ranged from 0.44 to 1.79 μg m^-2 s^-1, with a mean of 0.92±0.33 μg m^-2 s^-1, whereas over black spruce, isoprene fluxes ranged from −0.06 to 0.54 μg m^-2 s^-1, with a mean of 0.36±0.21 μg m^-2 s^-1. The isoprene fluxes were exponentially correlated with solar radiation and radiative surface temperature. High correlations between isoprene fluxes and the fluxes of CO₂ and latent heat were also observed. Carbon lost through isoprene emissions was about 0.7 and 0.8% of the CO₂ assimilation rate for aspen and black spruce, respectively. The results demonstrate that the aircraft-based relaxed eddy-accumulation technique is a promising approach for quantifying the atmosphere–surface exchange of VOCs on a regional scale.     

Air pollutants in rural homes in Guizhou,China – Concentrations,speciation, and size distribution

Several types of fuels, including coal, fuel wood, and biogas, are commonly used for cooking and heating in Chinese rural households, resulting in indoor air pollution and causing severe health impacts. In this paper, we report a study monitoring multiple pollutants including PM₁₀, PM_2.5, CO, CO₂, and volatile organic compounds (VOCs) from fuel combustion at households in Guizhou province of China. The results showed that most pollutants exhibited large variability for different type of fuels except for CO₂. Among these fuels, wood combustion caused the most serious indoor air pollution, with the highest concentrations of particulate matters (218～417 μg m^?3 for PM₁₀ and 201～304 μg m^?3 for PM_2.5), and higher concentrations of CO (10.8 ± 0.8 mg m^?3) and TVOC (about 466.7 ± 337.9 μg m^?3). Coal combustion also resulted in higher concentrations of particulate matters (220～250 μg m^?3 for PM₁₀ and 170～200 μg m^?3 for PM_2.5), but different levels for CO (respectively 14.5 ± 3.7 mg m^?3 for combustion in brick stove and 5.5 ± 0.7 mg m^?3 for combustion in metal stove) and TVOC (170 mg m^?3 for combustion in brick stove and 700 mg m^?3 for combustion in metal stove). Biogas was the cleanest fuel, which brought about the similar levels of various pollutants with the indoor case of non-combustion, and worth being promoted in more areas. Analysis of the chemical profiles of PM_2.5 indicated that OC and EC were dominant components for all fuels, with the proportions of 30～48%. A high fraction of SO₄^2? (31～34%) was detected for coal combustion. The cumulative percentages of these chemical species were within the range of 0.7～1.3, which was acceptable for the assessment of mass balance.     

Particulate matter in the indoor air of classrooms—exploratory results from Munich and surrounding area

Numerous epidemiological studies have demonstrated the association between particle mass (PM) concentration in outside air and the occurrence of health related problems and/or diseases. However, much less is known about indoor PM concentrations and associated health risks. In particular, data are needed on air quality in schools, since children are assumed to be more vulnerable to health hazards and spend a large part of their time in classrooms.On this background, we evaluated indoor air quality in 64 schools in the city of Munich and a neighbouring district outside the city boundary. In winter 2004–2005 in 92 classrooms, and in summer 2005 in 75 classrooms, data on indoor air climate parameters (temperature, relative humidity), carbon dioxide (CO₂) and various dust particle fractions (PM₁₀, PM_2.5) were collected; for the latter both gravimetrical and continuous measurements by laser aerosol spectrometer (LAS) were implemented. In the summer period, the particle number concentration (PNC), was determined using a scanning mobility particle sizer (SMPS). Additionally, data on room and building characteristics were collected by use of a standardized form. Only data collected during teaching hours were considered in analysis. For continuously measured parameters the daily median was used to describe the exposure level in a classroom.The median indoor CO₂ concentration in a classroom was 1603 ppm in winter and 405 ppm in summer. With LAS in winter, median PM concentrations of 19.8 μg m⁻³ (PM_2.5) and 91.5 μg m⁻³ (PM₁₀) were observed, in summer PM concentrations were significantly reduced (median PM_2.5=12.7 μg m⁻³, median PM₁₀=64.9 μg m⁻³). PM_2.5 concentrations determined by the gravimetric method were in general higher (median in winter: 36.7 μg m⁻³, median in summer: 20.2 μg m⁻³) but correlated strongly with the LAS-measured results. In explorative analysis, we identified a significant increase of LAS-measured PM_2.5 by 1.7 μg m⁻³ per increase in humidity by 10%, by 0.5 μg m⁻³ per increase in CO₂ indoor concentration by 100 ppm, and a decrease by 2.8 μg m⁻³ in 5–7th grade classes and by 7.3 μg m⁻³ in class 8–11 compared to 1–4th class. During the winter period, the associations were stronger regarding class level, reverse regarding humidity (a decrease by 6.4 μg m⁻³ per increase in 10% humidity) and absent regarding CO₂ indoor concentration. The median PNC measured in 36 classrooms ranged between 2622 and 12,145 particles cm⁻³ (median: 5660 particles cm⁻³).The results clearly show that exposure to particulate matter in school is high. The increased PM concentrations in winter and their correlation with high CO₂ concentrations indicate that inadequate ventilation plays a major role in the establishment of poor indoor air quality. Additionally, the increased PM concentration in low level classes and in rooms with high number of pupils suggest that the physical activity of pupils, which is assumed to be more pronounced in younger children, contributes to a constant process of resuspension of sedimented particles. Further investigations are necessary to increase knowledge on predictors of PM concentration, to assess the toxic potential of indoor particles and to develop and test strategies how to ensure improved indoor air quality in schools.     

Characterization of emissions from portable household combustion devices: particle size distributions,emission rates and factors,and potential exposures

A series of source tests were conducted to characterize emissions of particulate matter (PM), carbon monoxide (CO), carbon dioxide (CO₂), methane (CH₄), and total hydrocarbon (THC ) from five types of portable combustion devices. Tested combustion devices included a kerosene lamp, an oil lamp, a kerosene space heater, a portable gas range, and four unscented candles. All tests were conducted either in a well-mixed chamber or a well-mixed room, which enables us to determine emission rates and emission factors using a single-compartment mass balance model. Particle mass concentrations and number concentrations were measured using a nephelometric particle monitor and an eight-channel optical particle counter, respectively. Real-time CO concentrations were measured with an electrochemical sensor CO monitor. CO₂, CH₄, and THC were measured using a GC-FID technique. The results indicate that all particles emitted during steady burning in each of the tested devices were smaller than 1.0 μm in diameter with the vast majority in the range between 0.1 and 0.3 μm. The PM mass emission rates and emission factors for the tested devices ranged from 5.6±0.1 to 142.3±40.8 mg h⁻¹ and from 0.35±0.06 to 9.04±4.0 mg g⁻¹, respectively. The CO emission rates and emission factors ranged from 4.7±3.0 to 226.7±100 mg h⁻¹ and from 0.25±0.12 to 1.56±0.7 mg g⁻¹, respectively. The CO₂ emission rates and emission factors ranged from 5500±700 to 210,000±90,000 mg h⁻¹ and from 387±45 to 1689±640 mg g⁻¹, respectively. The contributions of CH₄ and THC to emission inventories are expected to be insignificant due both to the small emission factors and to the relatively small quantity of fuel consumed by these portable devices. An exposure scenario analysis indicates that every-day use of the kerosene lamp in a village house can generate fine PM exposures easily exceeding the US promulgated NAAQS for PM_2.5.     

Trace gas variations at Cape Point,South Africa,during May 1997 following a regional biomass burning episode

During the continuous monitoring of atmospheric parameters at the station Cape Point (34°S, 18°E), a smoke plume originating from a controlled fire of 30-yr-old fynbos was observed on 6 May 1997. For this episode, which was associated with a nocturnal inversion and offshore airflow, atmospheric parameters (solar radiation and meteorological data) were considered and the levels of various trace gases compared with those measured at Cape Point in maritime air. Concentration maxima in the morning of 6 May for CO₂, CO, CH₄ and O₃ amounted to 370.3 ppm, 491 ppb, 1730 ppb and 47 ppb, respectively, whilst the mixing ratios of several halocarbons (F-11, F-12, F-113, CCl₄ and CH₃CCl₃) remained at background levels. In the case of CO, the maritime background level for this period was exceeded by a factor of 9.8. Differences in ozone levels of up to 5 ppb between air intakes at 4 and 30 m above the station (located at 230 m above sea level) indicated stratification of the air advected to Cape Point during the plume event. Aerosols within the smoke plume caused the signal of global solar radiation and UV–A to be attenuated from 52.4 to 13.0 mW cm⁻² and from 2.3 to 1.3 mW cm⁻², respectively, 5 h after the trace gases had reached their maxima. Emission ratios (ERs) calculated for CO and CH₄ relative to CO₂ mixing ratios amounted to 0.042 and 0.0040, respectively, representing one of the first results for fires involving fynbos. The CO ER is somewhat lower than those given in the literature for African savanna fires (average ER=0.048), whilst for CH₄ the ER falls within the range of ERs reported for the flaming (0.0030) and smouldering phases (0.0055) of savanna fires. Non-methane hydrocarbon (NMHC) data obtained from a grab sample collected during the plume event were compared to background levels. The highest ERs (ΔNMHC/ΔCH₄) have been obtained for the C₂–C₃ hydrocarbons (e.g. ethene at 229.3 ppt ppb⁻¹), whilst the C₄–C₇ hydrocarbons were characterised by the lowest ERs (e.g. n-hexane at 1.0 and n-pentane at 0.8 ppt ppb⁻¹).     

Sulfuric odorous compounds emitted from pig-feeding operations

The objective of the study was to quantify the concentration and emission levels of sulfuric odorous compounds emitted from pig-feeding operations. Five types of pig-housing rooms were studied: gestation, farrowing, nursery, growing and fattening rooms. The concentration range of sulfuric odorous compounds in these pig-housing rooms were 30–200 ppb for hydrogen sulfide (H₂S), 2.5–20 ppb for methyl mercaptan (CH₃SH), 1.5–12 ppb for dimethyl sulfide (DMS; CH₃SCH₃) and 0.5–7 ppb for dimethyl disulfide (DMDS; CH₃S₂CH₃), respectively. The emission rates of H₂S, CH₃SH, DMS and DMDS were estimated by multiplying the average concentration (mg m⁻³) measured near the air outlet by the mean ventilation rate (m³ h⁻¹) and expressed either per area (mg m⁻² h⁻¹) or animal unit (AU; liveweight of the pig, 500 kg) (mg pig⁻¹ h⁻¹). As a result, the emission rates of H₂S, CH₃SH, DMS and DMDS in the pig-housing rooms were 14–64, 0.8–7.3, 0.4–3.4 and 0.2–1.9 mg m⁻² h⁻¹, respectively, based on pig's activity space and 310–723, 18–80, 9–39 and 5–22 mg AU⁻¹ h⁻¹, respectively, based on pig's liveweight, which indicates that their emission rates were similar, whether based upon the pig's activity space or liveweight. In conclusion, the concentrations and emission rates of H₂S were highest in the fattening room followed by the growing, nursery, farrowing and gestation rooms whereas those of CH₃SH, DMS and DMDS concentrations were largest in the growing room followed by the nursery, gestation and farrowing rooms.     

Continuous observations of carbon dioxide at Mace Head,Ireland from 1995 to 1999 and its net European ecosystem exchange

A 5-yr record of continuous high-frequency carbon dioxide CO₂ observations over the 1995–1999 period for the Mace Head Atmospheric Research Station has been examined to reveal a complex interplay between local- and regional-scale sources and sinks. During the winter months, an additional CO₂ source, over and above fossil fuel combustion, is required to support the observed concentrations of CO₂ in European regionally polluted air masses. During the summer months, an additional CO₂ sink is required. Over the entire study period, the additional net European ecosystem exchange source–sink required is –0.36±0.4 Gtonne C yr⁻¹.     

Estimation of wind blown dust emissions in Europe and its vicinity

The assessment of the wind blown dust emission for Europe and selected regions of North Africa and Southwest Asia was carried out using a mesoscale model. The mesoscale model was parameterized based on the current literature review. The model provides data on PM₁₀ emission from several dust reservoirs (anthropogenic, agriculture, semi- and natural) with spatial resolution of 10 × 10 km and temporal resolution of 1 h. The spatial variability of PM₁₀ emission depends on soil texture, land cover/land use as well as meteorological conditions. Lands covered with water or permanently wet were excluded from the model. The land covered with vegetation is treated as dust reservoir whose dust emission capacity depends on the type of vegetation and cover. The dust reservoirs are divided into reservoirs with stable and unstable surface. The changes of emission in time depend on meteorological parameters.The wind blown dust emission should be treated as a non-continuous spatio-temporal process. The emissions are estimated with high uncertainty. The estimated PM₁₀ yearly total load emitted by wind from the European territory is highly differentiated in space and time and is equal to 0.74 Tg. The total load of PM₁₀ emitted by wind from North African and Southwest Asian land surface located in the vicinity of European boundaries is assessed as nearly 50% (0.43 Tg) of the total load estimated for the whole Europe.The average yearly PM₁₀ emission factor for Europe was estimated at 0.139 Mg km^?2.The PM₁₀ emission from agricultural areas is estimated at 52% of the total wind blown emission from the domain of the European Union project “Improving and applying methods for the calculation of natural and biogenic emissions and assessment of impacts to the air quality” - NatAir.PM₁₀ emission factor for natural areas of Europe is estimated at 0.021 Mg km^?2. Appropriate factors for agricultural areas and anthropogenic areas are 0.157 Mg km^?2 and 0.118 Mg km^?2, respectively. The latter two factors are probably underestimated due to omitting in the model of other dust emission mechanisms than aeolian erosion.