Diurnal and weekday variations in the source contributions of ozone precursors in California's South Coast Air Basin

For at least 30 years, ozone (O3) levels on weekends in parts of California's South Coast (Los Angeles) Air Basin (SoCAB) have been as high as or higher than on weekdays, even though ambient levels of O3 precursors are lower on weekends than on weekdays. A field study was conducted in the Los Angeles area during fall 2000 to test whether proposed relationships between emission sources and ambient nonmethane hydrocarbon (NMHC) and oxides of nitrogen (NOx) levels can account for observed diurnal and day-of-week variations in the concentration and proportions of precursor pollutants that may affect the efficiency and rate of O3 formation. The contributions to ambient NMHC by motor vehicle exhaust and evaporative emissions, estimated using chemical mass balance (CMB) receptor modeling, ranged from 65 to 85% with minimal day-of-week variation. Ratios of ambient NOx associated with black carbon (BC) to NOx associated with carbon monoxide (CO) were approximately 1.25 +/- 0.22 during weekdays and 0.76 +/- 0.07 and 0.52 +/- 0.07 on Saturday and Sunday, respectively. These results demonstrate that lower NOx emissions from diesel exhaust can be a major factor causing lower NOx mixing ratios and higher NMHC/NOx ratios on weekends. Nonmobile sources showed no significant day-of-week variations in their contributions to NMHC. Greater amounts of gasoline emissions are carried over on Friday and Saturday evenings but are, at most, a minor factor contributing to higher NMHC/NOx ratios on weekend mornings.     

Diurnal and Weekday Variations in the Source Contributions of Ozone Precursors in California’s South Coast Air Basin

Abstract

For at least 30 years, ozone (O₃) levels on weekends in parts of California’s South Coast (Los Angeles) Air Basin (SoCAB) have been as high as or higher than on weekdays, even though ambient levels of O₃ precursors are lower on weekends than on weekdays. A field study was conducted in the Los Angeles area during fall 2000 to test whether proposed relationships between emission sources and ambient nonmethane hydrocarbon (NMHC) and oxides of nitrogen (NO_x) levels can account for observed diurnal and day-of-week variations in the concentration and proportions of precursor pollutants that may affect the efficiency and rate of O₃ formation. The contributions to ambient NMHC by motor vehicle exhaust and evaporative emissions, estimated using chemical mass balance (CMB) receptor modeling, ranged from 65 to 85% with minimal day-of-week variation. Ratios of ambient NO_x associated with black carbon (BC) to NO_x associated with carbon monoxide (CO) were approximately 1.25 ± 0.22 during weekdays and 0.76 ± 0.07 and 0.52 ± 0.07 on Saturday and Sunday, respectively. These results demonstrate that lower NO_x emissions from diesel exhaust can be a major factor causing lower NO_x mixing ratios and higher NMHC/NO_x ratios on weekends. Nonmobile sources showed no significant day-of-week variations in their contributions to NMHC. Greater amounts of gasoline emissions are carried over on Friday and Saturday evenings but are, at most, a minor factor contributing to higher NMHC/NO_x ratios on weekend mornings.     

Characterization of Emissions from Vehicles Using Methanol and Methanol-Gasoline Blended Fuels

Exhaust and evaporative emissions were examined from vehicles fueled with methanol or a gasoline-methanol blend. Regulated automobile pollutants, as well as detailed hydrocarbons, methanol, and aldehydes were measured, and exhaust emission trends were obtained for vehicle operation over five different driving cycles. Results indicated that use of the blended fuel does not generally have any significant effect on base-line exhaust emission rates of regulated pollutants; however, emission rates of aldehydes increased during the Federal Test Procedure. Aldehyde emissions from the methanol-fueled car were roughly an order of magnitude higher than those resulting from blended fuel usage. The hydrocarbon composition of evaporative emissions with the blended fuel was similar to that with the base-line fuel except when canister breakthrough occurred. Evaporative emissions during breakthrough were comprised chiefly of N-butane.     

On-road remote sensing measurements and fuel-based motor vehicle emission inventory in Hangzhou,China

Motor vehicles are one of the largest sources of air pollutants worldwide. Despite their importance, motor vehicle emissions are inadequately understood and quantified, esp. in developing countries. In this study, the real-world emissions of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxide (NO) were measured using an on-road remote sensing system at five sites in Hangzhou, China in 2004 and 2005. Average emission factors of CO, HC and NO_x for petrol vehicles of different model year, technology class and vehicle type were calculated in grams of pollutant per unit of fuel use (g l⁻¹) from approximately 32,260 petrol vehicles. Because the availability of data used in traditional on-road mobile source estimation methodologies is limited in China, fuel-based approach was implemented to estimate motor vehicle emissions using fuel sales as a measure of vehicle activity, and exhaust emissions factors from remote sensing measurements. The fuel-based exhaust emission inventories were also compared with the results from the recent international vehicle emission (IVE) model. Results show that petrol vehicle fleet in Hangzhou has significantly high CO emissions, relatively high HC and low NO_x, with the average emission factors of 193.07±15.63, 9.51±2.40 and 5.53±0.48 g l⁻¹, respectively. For year 2005 petrol vehicles exhaust emissions contributed with 182,013±16,936, 9107±2255 and 5050±480 metric ton yr⁻¹ of CO, HC and NO_x, respectively. The inventories are 45.5% higher, 6.6% higher and 53.7% lower for CO, HC and NO_x, respectively, than the estimates using IVE travel-based model. In addition, a number of insights about the emission distributions and formation mechanisms have been obtained from an in-depth analysis of these results.     

Seasonal impact of blending oxygenated organics with gasoline on motor vehicle tailpipe and evaporative emissions.

Emissions from a 1988 GM Corsica with adaptive learning closed loop control were measured with 4 fuels at 40, 75, and 90 degrees F. Evaporative and exhaust emissions were examined from each fuel at each test temperature. Test fuels were unleaded summer grade gasoline; a blend of this gasoline containing 8.1 percent ethanol; a refiner's blend stock; and the blend stock containing 16.2 percent methyl tertiary butyl ether. The ethanol and MTBE blends contained 3.0 percent oxygen by weight. Regulated emissions (total hydrocarbons, carbon monoxide, and oxides of nitrogen), detailed aldehydes, detailed hydrocarbons, ethanol, MTBE, benzene, and 1,3-butadiene were determined. The highest levels of regulated emissions were produced at the lower temperature. Blended fuels produced almost twice the evaporative hydrocarbon emissions at high temperatures as did the base fuels. Benzene emissions varied with fuels and operating temperatures, while 1,3-butadiene emissions decreased slightly with increasing temperatures. Formaldehyde emissions were not sensitive to fuel or temperature changes. Ethanol fuel blend total aldehyde emissions increased by 40 percent due to increased acetaldehyde emissions. Fuel blends had approximately a 3 percent economy decrease. The MTBE fuel blend appeared to offer the most reduction in total hydrocarbon, carbon monoxide, and oxides of nitrogen for the fuels and temperatures tested.     

An Evaluation of the Fuel Factor Through Direct Measurement of Photochemical Reactivity of Emissions

Findings in research at the Bureau of Mines Bartlesville Petroleum Research Center show that photochemical reactivities of vehicular emissions are reliably measured in laboratory experiments in which smog manifestations are observed directly. Results of the direct smog-chamber measurements reveal that the photochemical behavior of emissions may differ significantly from the behavior that is predicted from the exhaust composition using reactivity scales. The concept of direct measurement of reactivity was applied to determine differences in characteristics of emissions from 20 passenger vehicles, each tested using 10 different fuels. The primary objective of the fuel study was to assess the over-all effect on vehicle emissions of fuel modifications designed to reduce the photochemical pollution associated with automotive evaporative losses. A similar, brief, comparative study of leaded and nonleaded fuels was also made. Reducing volatility was found to reduce the over-all smog potential of vehicle emissions but involved some penalty by way of increased exhaust emissions. Replacing light olefin with the corresponding paraffin also reduced over-all smog potential and in this case exhaust reactivity was not affected. In general greater smog potential was found to be associated with prototype nonleaded fuels than with leaded fuels typical of products currently marketed.     

Seasonal Impact of Blending Oxygenated Organics with Gasoline on Motor Vehicle Tailpipe and Evaporative Emissions

Emissions from a 1988 GM Corsica with adaptive learning closed loop control were measured with 4 fuels at 40, 75, and 90° F. Evaporative and exhaust emissions were examined from each fuel at each test temperature. Test fuels were unleaded summer grade gasoline; a blend of this gasoline containing 8.1 percent ethanol; a refiner’s blend stock; and the blend stock containing 16.2 percent methyl tertiary butyl ether. The ethanol and MTBE blends contained 3.0 percent oxygen by weight. Regulated emissions (total hydrocarbons, carbon monoxide, and oxides of nitrogen), detailed aldehydes, detailed hydrocarbons, ethanol, MTBE, benzene, and 1, 3-butadiene were determined.

The highest levels of regulated emissions were produced at the lower temperature. Blended fuels produced almost twice the evaporative hydrocarbon emissions at high temperatures as did the base fuels. Benzene emissions varied with fuels and operating temperatures, while 1, 3-butadiene emissions decreased slightly with increasing temperatures. Formaldehyde emissions were not sensitive to fuel or temperature changes. Ethanol fuel blend total aldehyde emissions Increased by 40 percent due to increased acetaldehyde emissions.

Fuel blends had approximately a 3 percent economy decrease. The MTBE fuel blend appeared to offer the most reduction in total hydrocarbon, carbon monoxide, and oxides of nitrogen for the fuels and temperatures tested.     

Influence of Oxygenated Fuels on the Emissions from Three Pre-1985 Light-Duty Passenger Vehicles

Tailpipe and evaporative emissions from three pre-1985 passenger motor vehicles operating on an oxygenated blend fuel and on a nonoxygenated base fuel were characterized. Emission data were collected for vehicles operating over the Federal Test Procedure at 40,75, and 90°F to simulate ambient driving conditions. The two fuels tested were a commercial summer grade regular gasoline (the nonoxygenated base fuel) and an oxygenated fuel containing 9.5 percent methyl tert-butyl ether (MTBE), more olefins, and fewer aromatics than the base fuel. The emissions measured were total hydrocarbons (THCs), speciated hydrocarbons, speciated aldehydes, carbon monoxide (CO), oxides of nitrogen (NO_x), benzene, and 1,3-butadiene.

This study showed no pattern of tailpipe regulated emission reduction when oxygenated fuel was used. Tailpipe emissions from the 1984 Buick Century without a catalyst and the 1977 Mustang with catalyst decreased with the MTBE fuel. However, emissions from the 1984 Buick Century and the 1980 Chevrolet Citation, both fitted with catalysts increased. The vehicles emitted more 1,3- butadiene and, in general, more NO_x when operated with the base fuel.

THC, CO, benzene, and 1,3-butadiene emissions from both fuels and all vehicles, in general, decreased with increasing test temperature, whereas NO_x emissions, in general, increased with increasing test temperature. Formaldehyde, acetaldehyde, and total aldehydes also showed a decrease in emissions as test temperature increased. More formaldehyde was emitted when the MTBE fuel was used.

Evaporative, diurnal, and hot soak emissions from the base fuel were greater than those from the MTBE fuel. The evaporated emissions from both fuels increased with increasing test temperatures. Diurnal data indicate that canister conditioning (bringing the evaporative charcoal canister to equilibrium) is required before testing.     

Effect of methyl tertiary butyl ether concentrations on exhaust emissions from gasoline used in the metropolitan area of Mexico City

In this work, the primary objective was to assess the impact of oxygenated fuel on the exhaust emissions from an important fraction of vehicles in the Metropolitan Area of Mexico City (MAMC). The results aim to provide information on the actual effect of MTBE on a fleet that represents more than 60% of the in-use vehicles in the MAMC. Ten vehicles were tested with a low-octane base gasoline, and 10 more with a regular-grade unleaded base gasoline. Three MTBE concentrations, 5, 10, and 15 vol %, were tested following the U.S. Federal Test Procedure (FTP). CO, total HC, and NOx from the exhaust gases were quantitatively evaluated and also characterized for FTP speciated organic emissions. From this data, the O3-forming potential of the fuels was calculated. Results show that for the fleet using low-octane gasoline, the addition of 10% MTBE substantially reduced CO emissions, but total HC concentration in the exhaust showed a modest decrease. For the regular gasoline, the 10% MTBE blend seemed to be the best choice, but there was not a significant decrease in emissions. The specific reactivity of each fuel, expressed in grams of O3 per gram of nonmethane organic gases, increased with MTBE concentration in both cases. This result is important to consider, especially for a region like Mexico City, which has high atmospheric O3 concentrations.     

Particulate matter in new technology diesel exhaust (NTDE) is quantitatively and qualitatively very different from that found in traditional diesel exhaust (TDE)

Diesel exhaust (DE) characteristic of pre-1988 engines is classified as a "probable" human carcinogen (Group 2A) by the International Agency for Research on Cancer (IARC), and the U.S. Environmental Protection Agency has classified DE as "likely to be carcinogenic to humans." These classifications were based on the large body of health effect studies conducted on DE over the past 30 or so years. However, increasingly stringent U.S. emissions standards (1988-2010) for particulate matter (PM) and nitrogen oxides (NOx) in diesel exhaust have helped stimulate major technological advances in diesel engine technology and diesel fuel/lubricant composition, resulting in the emergence of what has been termed New Technology Diesel Exhaust, or NTDE. NTDE is defined as DE from post-2006 and older retrofit diesel engines that incorporate a variety of technological advancements, including electronic controls, ultra-low-sulfur diesel fuel, oxidation catalysts, and wall-flow diesel particulate filters (DPFs). As discussed in a prior review (T. W. Hesterberg et al.; Environ. Sci. Technol. 2008, 42, 6437-6445), numerous emissions characterization studies have demonstrated marked differences in regulated and unregulated emissions between NTDE and "traditional diesel exhaust" (TDE) from pre-1988 diesel engines. Now there exist even more data demonstrating significant chemical and physical distinctions between the diesel exhaust particulate (DEP) in NTDE versus DEP from pre-2007 diesel technology, and its greater resemblance to particulate emissions from compressed natural gas (CNG) or gasoline engines. Furthermore, preliminary toxicological data suggest that the changes to the physical and chemical composition of NTDE lead to differences in biological responses between NTDE versus TDE exposure. Ongoing studies are expected to address some of the remaining data gaps in the understanding of possible NTDE health effects, but there is now sufficient evidence to conclude that health effects studies of pre-2007 DE likely have little relevance in assessing the potential health risks of NTDE exposures.     

Bioethanol-gasoline fuel blends: exhaust emissions and morphological characterization of particulate from a moped engine

This study was aimed at evaluating the effects of gasoline-ethanol blends on the exhaust emissions in a catalyst-equipped four-stroke moped engine. The ethanol was blended with unleaded gasoline in at percentages (10, 15, and 20% v/v). The regulated pollutants and the particulate matter emissions were evaluated over the European ECE R47 driving cycle on the chassis dynamometer bench. Particulate matter was characterized in terms of total mass collected on filters and total number ofparticles in the range 7 nm-10 microm measured by electrical low-pressure impactor (ELPI). In addition, particle-phase polycyclic aromatic hydrocarbons (PAHs) emissions were evaluated to assess the health impact of the emitted particulate. Finally, an accurate morphological analysis was performed on the particulate by high-resolution transmission electron microscope (TEM) equipped with a digital image-processing/data-acquisition system. In general, CO emission reductions of 60-70% were obtained with 15 and 20% v/v ethanol blends, while the ethanol use did not reduce hydrocarbon (HC) and NOx emissions. No evident effect of ethanol on the particulate mass emissions and associated PAHs emissions was observed. Twenty-one PAHs were quantified in the particulate phase with emissions ranging from 26 to 35 microg/km and benzo[a]pyrene equivalent (BaPeq) emission factors from 2.2 to 4.1 microg/km. Both particulate matter and associated PAHs with higher carcinogenic risk were mainly emitted in the submicrometer size range (<0.1 microm). On the basis of the TEM observations, no relevant effect of the ethanol use on the particulate morphology was evidenced, showing aggregates composed ofprimary particles with mean diameters in the range 17.5-32.5 nm.     

Size and composition distributions of particulate matter emissions: part 1--light-duty gasoline vehicles

Size-resolved particulate matter (PM) emitted from light-duty gasoline vehicles (LDGVs) was characterized using filter-based samplers, cascade impactors, and scanning mobility particle size measurements in the summer 2002. Thirty LDGVs, with different engine and emissions control technologies (model years 1965-2003; odometer readings 1264-207,104 mi), were tested on a chassis dynamometer using the federal test procedure (FTP), the unified cycle (UC), and the correction cycle (CC). LDGV PM emissions were strongly correlated with vehicle age and emissions control technology. The oldest models had average ultrafine PM0.1 (0.056- to 0.1-microm aerodynamic diameter) and fine PM1.8 (< or =1.8-microm aerodynamic diameter) emission rates of 9.6 mg/km and 213 mg/km, respectively. The newest vehicles had PM0.1 and PM1.8 emissions of 51 microg/km and 371 microg/km, respectively. Light duty trucks and sport utility vehicles had PM0.1 and PM1.8 emissions nearly double the corresponding emission rates from passenger cars. Higher PM emissions were associated with cold starts and hard accelerations. The FTP driving cycle produced the lowest emissions, followed by the UC and the CC. PM mass distributions peaked between 0.1- and 0.18-microm particle diameter for all vehicles except those emitting visible smoke, which peaked between 0.18 and 0.32 microm. The majority of the PM was composed of carbonaceous material, with only trace amounts of water-soluble ions. Elemental carbon (EC) and organic matter (OM) had similar size distributions, but the EC/OM ratio in LDGV exhaust particles was a strong function of the adopted emissions control technology and of vehicle maintenance. Exhaust from LDGV classes with lower PM emissions generally had higher EC/OM ratios. LDGVs adopting newer technologies were characterized by the highest EC/OM ratios, whereas OM dominated PM emissions from older vehicles. Driving cycles with cold starts and hard accelerations produced higher EC/OM ratios in ultrafine particles.     

Automotive Exhaust Emission Levels by Geographic Area and Vehicle Make A Nationwide Survey

Gross average automotive exhaust emissions data collected by the Atlantic Richfield Clean Air Caravan during the summer of 1970 showed only slight geographical variations when the specific makes were ignored. When considering specific makes, significant differences were found on an average emissions basis. Vehicle population—emission distributions showed wide variations in the 50% population levels and in the percent of vehicles with emissions greater than specified values. Hydrocarbon (HC) and carbon monoxide (CO) data are given on a gross basis for the 1970, 1968-69, 1966-67, and pre-1966 model year group vehicles. Average HC and CO emissions and vehicle population-Idle emissions distribution curves are included for specific make vehicles in selected areas.     

Size and composition distributions of particulate matter emissions: part 2--heavy-duty diesel vehicles

Particulate matter (PM) emissions from heavy-duty diesel vehicles (HDDVs) were collected using a chassis dynamometer/dilution sampling system that employed filter-based samplers, cascade impactors, and scanning mobility particle size (SMPS) measurements. Four diesel vehicles with different engine and emission control technologies were tested using the California Air Resources Board Heavy Heavy-Duty Diesel Truck (HHDDT) 5 mode driving cycle. Vehicles were tested using a simulated inertial weight of either 56,000 or 66,000 lb. Exhaust particles were then analyzed for total carbon, elemental carbon (EC), organic matter (OM), and water-soluble ions. HDDV fine (< or =1.8 microm aerodynamic diameter; PM1.8) and ultrafine (0.056-0.1 microm aerodynamic diameter; PM0.1) PM emission rates ranged from 181-581 mg/km and 25-72 mg/km, respectively, with the highest emission rates in both size fractions associated with the oldest vehicle tested. Older diesel vehicles produced fine and ultrafine exhaust particles with higher EC/OM ratios than newer vehicles. Transient modes produced very high EC/OM ratios whereas idle and creep modes produced very low EC/OM ratios. Calcium was the most abundant water-soluble ion with smaller amounts of magnesium, sodium, ammonium ion, and sulfate also detected. Particle mass distributions emitted during the full 5-mode HDDV tests peaked between 100-180 nm and their shapes were not a function of vehicle age. In contrast, particle mass distributions emitted during the idle and creep driving modes from the newest diesel vehicle had a peak diameter of approximately 70 nm, whereas mass distributions emitted from older vehicles had a peak diameter larger than 100 nm for both the idle and creep modes. Increasing inertial loads reduced the OM emissions, causing the residual EC emissions to shift to smaller sizes. The same HDDV tested at 56,000 and 66,000 lb had higher PM0.1 EC emissions (+22%) and lower PM0.1 OM emissions (-38%) at the higher load condition.     

Inspection and Maintenance for Reducing Automobile Emissions

EPA has recently evaluated several inspection and maintenance approaches for in-use vehicles that are potentially applicable to pre-1975 automobiles. The results of this evaluation are described and used to estimate the effecliveness and cost of inspection/maintenance for reducing total automobile emissions through 1985. It is estimated that inspection/maintenance programs for pre-1975 automobiles may be capable of achieving eight and ten percent reductions in total automobile emissions of HC and CO respectively until 1980 and two to three percent reductions in 1985. The need for inspection of automobiles of model year 1975 and later, and the potential applicability of present short-duration inspection procedures to these vehicles, are also discussed.     

Influence of fuel composition on polycyclic aromatic hydrocarbon emissions from a fleet of in-service passenger cars

The composition of exhaust emissions from eight in-service passenger cars powered by liquefied petroleum gas (LPG) and unleaded petrol (ULP) were measured on a chassis dynamometer at two driving speeds (60 and 80 km h⁻¹) with the aims of evaluating their polycyclic aromatic hydrocarbon (PAH) contents and investigating the effects of the type of fuel on vehicle performance, ambient air quality and associated health risks. Naphthalene, fluorene, phenanthrene, anthracene, pyrene, chrysene, benzo(a)anthracene and benzo(b)fluoranthene were the most prominent PAHs emitted by both ULP and LPG powered cars. The total emission factors of PAHs from LPG cars were generally lower than (but statistically comparable with) those of ULP cars. Similarly, the total BAP_eq of the PAHs emitted by LPG cars were lower than those from ULP cars. Multi-criteria decision making (MCDM) methods showed that cars powered by LPG fuel performed better than those powered by ULP fuel in term of PAH levels. The implications of these observations on the advantages and disadvantages of using ULP and LPG fuels are discussed.     

Regulated and unregulated emissions from modern 2010 emissions-compliant heavy-duty on-highway diesel engines

The U.S. Environmental Protection Agency (EPA) established strict regulations for highway diesel engine exhaust emissions of particulate matter (PM) and nitrogen oxides (NO_x) to aid in meeting the National Ambient Air Quality Standards. The emission standards were phased in with stringent standards for 2007 model year (MY) heavy-duty engines (HDEs), and even more stringent NO_X standards for 2010 and later model years. The Health Effects Institute, in cooperation with the Coordinating Research Council, funded by government and the private sector, designed and conducted a research program, the Advanced Collaborative Emission Study (ACES), with multiple objectives, including detailed characterization of the emissions from both 2007- and 2010-compliant engines. The results from emission testing of 2007-compliant engines have already been reported in a previous publication. This paper reports the emissions testing results for three heavy-duty 2010-compliant engines intended for on-highway use. These engines were equipped with an exhaust diesel oxidation catalyst (DOC), high-efficiency catalyzed diesel particle filter (DPF), urea-based selective catalytic reduction catalyst (SCR), and ammonia slip catalyst (AMOX), and were fueled with ultra-low-sulfur diesel fuel (~6.5 ppm sulfur). Average regulated and unregulated emissions of more than 780 chemical species were characterized in engine exhaust under transient engine operation using the Federal Test Procedure cycle and a 16-hr duty cycle representing a wide dynamic range of real-world engine operation. The 2010 engines’ regulated emissions of PM, NO_X, nonmethane hydrocarbons, and carbon monoxide were all well below the EPA 2010 emission standards. Moreover, the unregulated emissions of polycyclic aromatic hydrocarbons (PAHs), nitroPAHs, hopanes and steranes, alcohols and organic acids, alkanes, carbonyls, dioxins and furans, inorganic ions, metals and elements, elemental carbon, and particle number were substantially (90 to >99%) lower than pre-2007-technology engine emissions, and also substantially (46 to >99%) lower than the 2007-technology engine emissions characterized in the previous study.

Implications:?Heavy-duty on-highway diesel engines equipped with DOC/DPF/SCR/AMOX and fueled with ultra-low-sulfur diesel fuel produced lower emissions than the stringent 2010 emission standards established by the U.S. Environmental Protection Agency. They also resulted in significant reductions in a wide range of unregulated toxic emission compounds relative to older technology engines. The increased use of newer technology (2010+) diesel engines in the on-highway sector and the adaptation of such technology by other sectors such as nonroad, displacing older, higher emissions engines, will have a positive impact on ambient levels of PM, NOx, and volatile organic compounds, in addition to many other toxic compounds.     

Long-Term Efficiency of Catalytic Converters Operating in Mexico City

ABSTRACT

A 1999 ordinance by the Government of Mexico City bans 1993 model-year vehicles from on-road operation if their catalytic converters are not replaced with new ones. To validate the benefits of this action, we examined three issues related to exhaust emissions of vehicles equipped with catalytic converters. After selecting representative fleets of in-use vehicles, a comparison between emissions and catalyst efficiency in cars with two categories of exhaust emission limits was carried out. For that purpose, two fleets were selected, each made up of 10 vehicles run under similar conditions. A third, larger fleet with emissions control systems was used to evaluate and simulate real-world conditions of vehicles in a controlled laboratory. Finally, the aging effect on the catalytic converter was studied on vehicles run for 100,000 km, replacing their old emission control devices for new ones.

The 1991-1992 model-year vehicles showed a high percentage of compliance with the corresponding emissions standard (90%) in comparison with 1993 model-year and later vehicles (Tier 0). However, NO_x emissions were higher for the newer vehicles. Fifty percent of the 1991-1992 model-year vehicles evaluated under the official inspection/maintenance (I/M) procedure did not meet the regulated emissions standard when the results were compared with those of the U.S. Federal Test Procedure     

Origins of Manganese in Air Participates in California

The proportions of manganese to other metals in samples of airborne fine particles taken at some sites in California have increased greatly since the beginning of 1985. Here, data are presented which indicate that the addition of manganese to leaded gasoline is largely responsible for this increase. Concentrations of manganese, silicon, titanium, iron, lead and other elements in airborne particles were measured using energy-dispersive X-ray fluorescence analysis. Coefficients of correlation among levels of manganese, iron and lead measured at twenty sites in California were calculated. Levels of manganese and iron are generally highly correlated because of the presence of large amounts of these elements in the earth’s crust. Levels of airborne manganese and lead at sites In Southern California are often highly correlated, suggesting a vehicular source of manganese. Observed manganese concentrations are apportioned into two major sources: the earth’s crust and motor vehicles. The apportionment indicates that vehicular emissions of manganese may account for a significant part of the total at urban sites in Southern California. At most other sites, the contribution from vehicles is found to be far smaller than that from the earth’s crust.     

Particulate Matter in New Technology Diesel Exhaust (NTDE) is Quantitatively and Qualitatively Very Different from that Found in Traditional Diesel Exhaust (TDE)

ABSTRACT

Diesel exhaust (DE) characteristic of pre-1988 engines is classified as a “probable” human carcinogen (Group 2A) by the International Agency for Research on Cancer (IARC), and the U.S. Environmental Protection Agency has classified DE as “likely to be carcinogenic to humans.” These classifications were based on the large body of health effect studies conducted on DE over the past 30 or so years. However, increasingly stringent U.S. emissions standards (1988–2010) for particulate matter (PM) and nitrogen oxides (NO_x) in diesel exhaust have helped stimulate major technological advances in diesel engine technology and diesel fuel/lubricant composition, resulting in the emergence of what has been termed New Technology Diesel Exhaust, or NTDE. NTDE is defined as DE from post-2006 and older retrofit diesel engines that incorporate a variety of technological advancements, including electronic controls, ultra-low-sulfur diesel fuel, oxidation catalysts, and wall-flow diesel particulate filters (DPFs). As discussed in a prior review (T. W. Hesterberg et al.; Environ. Sci. Technol. 2008, 42, 6437-6445), numerous emissions characterization studies have demonstrated marked differences in regulated and unregulated emissions between NTDE and “traditional diesel exhaust” (TDE) from pre-1988 diesel engines. Now there exist even more data demonstrating significant chemical and physical distinctions between the diesel exhaust particulate (DEP) in NTDE versus DEP from pre-2007 diesel technology, and its greater resemblance to particulate emissions from compressed natural gas (CNG) or gasoline engines. Furthermore, preliminary toxicological data suggest that the changes to the physical and chemical composition of NTDE lead to differences in biological responses between NTDE versus TDE exposure. Ongoing studies are expected to address some of the remaining data gaps in the understanding of possible NTDE health effects, but there is now sufficient evidence to conclude that health effects studies of pre-2007 DE likely have little relevance in assessing the potential health risks of NTDE exposures.

IMPLICATIONS Based on the distinct physical and chemical properties of New Technology Diesel Exhaust (NTDE), it has become clear that findings from the health effects studies conducted on traditional DE (TDE) over the last 30 years have little relevance to NTDE, which is more similar to the exhaust from compressed natural gas (CNG) or gasoline engine emissions than to traditional TDE. Once sufficient health effects data are available for NTDE, it will thus be necessary to conduct new hazard and risk assessments for NTDE that are independent of the DE toxicological database acquired on emissions from pre–2007 diesel technology.