低碳氮比对生物膜-电极反应器反硝化的影响

以乙酸钠作为碳源,给阴阳极外加2V的直流电压,考察了不同低C/N对连续运行的生物膜-电极反应器反硝化的影响。结果表明,当C/N从1.5∶1减少到0.8∶1时,生物膜-电极反应器NO-3-N去除率从99.5%下降至64.1%,出水NO-3-N的浓度从0.27mg/L增加到17.96mg/L,出水NO-2-N的浓度从0.24mg/L增加到2.6mg/L,出水NH+4-N浓度从4.93mg/L下降至3.35mg/L。当C/N为1.5∶1时,生物膜-电极反应器的自养反硝化率仅为8.0%,当C/N降至1∶1时,自养反硝化率增加至30.4%,然而,当C/N从1∶1进一步降低至0.8∶1时,自养反硝化率却从30.4%下降至21.8%。各C/N条件下,生物膜-电极反应器出水的SCOD浓度均高于对照生物膜反应器。生物膜-电极反应器的自养反硝化率与其出水pH呈正相关。     

同步硝化反硝化生物脱氮技术研究

讨论了影响同步硝化反硝化反应的各参数,并进行了单因素实验与正交实验,获得了同步硝化反硝化生物脱氮工艺运行的最佳条件:DO浓度控制在0.5～2 mg/L,COD浓度为600～800mg/L,混合液悬浮固体(MLSS)为5000 mg/L,pH值在8.0左右,反应时间为6 h.在此条件下,氨氮及COD的去除率都较高,分别达85%和95%,总氮去除率为68 5%.     

低氧条件下同时硝化和反硝化机理初探

采用人工配水 ,对低氧条件下完全混合系统中氮的去除进行了研究。实验结果表明 ,在低氧条件下 (DO为 0 .3～0 .8mg/L )完全混合系统的同时硝化和反硝化具有一定的可行性。在泥龄为 45 d,C/N比为 10∶ 1,F/M为 0 .1g CODCr/(g ML SS·d)条件下 ,总氮的去除率达 66.7%。经分析 ,本实验发生的硝化反应仍然是自养硝化菌的好氧硝化 ,同时硝化和反硝化现象应归因于微环境理论     

常温下连续流短程硝化反硝化研究

常温(26～30℃)下应用连续流短程硝化反硝化工艺处理模拟城市生活污水,对连续流短程硝化反硝化污泥的运行参数进行了研究.结果表明,在常温、进水NH4 -N为50 mg/L、曝气区pH为7.5～8.0、曝气量为0.3 L/min、曝气区水力停留时间为4 h的条件下,NO2- -N/(NO3- -N NO2- -N)达0.677,TN去除率为35%左右;在上述条件下,无需调节曝气区pH,选择前置反硝化区与曝气区的体积比为1:2、前置反硝化区水力停留时间为2 h、回流比为2:1时,连续流短程硝化反硝化工艺的TN去除率达88.9%,COD去除率达92.7%;pH的变化规律正确反映了系统运行状况,可作为系统运行的实时控制参数.     

MBR工艺短硝化反硝化处理生活污水的研究

以模拟生活污水为对象,研究了中温(25～30℃)条件下,膜生物反应器-短硝化反硝化生物脱氮的效果,试验结果表明,在曝气量为0.15 m3/h,pH值为7～8的条件下,出水COD保持在100 mg/L以下(平均49 mg/L),出水氨氮在5.0 mg/L以下(平均3.1 mg/L),NO2-得到了富集,出水中基本监测不出NO3-,总氮去除率平均为86.2%,最高达94.0%,且系统的耐冲击负荷能力较好;曝气量和pH值是短硝化过程的重要影响因素.     

苯酚对活性污泥硝化与反硝化动力学的影响

通过批次试验,研究苯酚与活性污泥缺氧和好氧接触对微生物硝化和反硝化作用的影响。结果表明:(1)苯酚对缺氧2h后的活性污泥硝化有抑制作用,且苯酚浓度越高,抑制作用越强。当苯酚浓度较低时对自养菌的最大比氨氧化速率(AUR)的抑制作用能用竞争性抑制Monod方程拟合,半数抑制质量浓度(IC50)为19.2mg/L。(2)苯酚对直接曝气的活性污泥比对缺氧接触2h后再曝气的活性污泥的硝化抑制作用更强,当苯酚从0mg/L增加到10.0mg/L,AUR由2.51mg/(L·h)降至0.36mg/(L·h),且在10.0mg/L时,硝化抑制率(IR)高达85.7%。(3)苯酚的抑制效应随着缺氧时间延长而逐渐降低。当苯酚为10.0mg/L时,直接曝气的活性污泥受到的硝化抑制最强,IR为85.8%,并在缺氧4h后IR降为0。(4)当碳源充足时,活性污泥的反硝化菌对苯酚的耐受力较强,苯酚对活性污泥的反硝化过程没有影响,微生物的反硝化速率(NUR)维持在5.279～5.308mmol/(mg·h)。     

包埋活性污泥和反硝化污泥全程硝化反硝化脱氮

将活性污泥和驯化所得的反硝化污泥菌泥按适当比例混合后,用聚乙烯醇(PVA)将其包埋,制成直径为3～4mm的颗粒小球.以模拟废水为处理对象,在流化床反应器内进行实验.结果表明,包埋颗粒小球对氮素和COD的去除效果良好,当包埋颗粒填充率为7％～8％(体积比),控制其他条件,12h的NH4+-N和TN去除率均在95％以上,对COD的去除率大于95％.整个过程中NO2--N未见明显积累,因此为全程硝化反硝化脱氮.最后,通过单因素实验得出的最佳温度、pH值和溶解氧浓度分别为30℃、7.5和4 mg/L.     

一株反硝化细菌的分离鉴定及其反硝化特性

从处理城镇污水的移动床生物膜反应器中分离获得一株反硝化细菌D3,并进一步研究该菌株的系统发育地位及反硝化特性。采用16S rDNA序列分析对菌株进行初步鉴定,探讨了基质浓度、起始pH和温度对菌株反硝化活性的影响。根据形态学特征、生理生化特性及16S rDNA序列测定分析,初步鉴定菌株属于寡养单胞菌属。该菌能利用硝酸钠或亚硝酸钠进行反硝化作用,最佳电子受体是硝酸盐氮,反硝化速率最大为19.86 mg/(L·h),最适生长pH为7.36,最适生长温度为33.5℃。菌株D3在初始硝态氮浓度为140 mg/L,以乙酸钠为惟一碳源,pH为7.36,温度33.5℃的最优生长条件下,培养10 h进入对数生长期,倍增时间为9.9 h,48 h内硝酸盐还原率达95%。     

短程反硝化聚磷的反硝化特征研究

研究了温度、pH值、电子供体种类及电子受体种类对反硝化的影响.试验结果表明,(1)在相同试验条件下,亚硝酸型反硝化与硝酸型反硝化的速率与硝态氮的浓度有关.在温度为25℃、pH为7的条件下,基质浓度＜300mg/L时短程反硝化速率较快;基质浓度≥300 mg/L时,以NO3-为基质的反硝化速率较大.(2)具有大量碳源储存物(PHB)的细菌可实现快速的内源性反硝化脱氮,而处于饥饿状态的细菌的内源性反硝化效率极低.     

MFC强化同步短程硝化反硝化工艺的启动

微生物燃料电池(MFC)可在阴极实现反硝化、短程反硝化和同步硝化反硝化并产生电能,但在MFC阴极实现同步短程硝化反硝化的研究尚未见到报道。为了探讨MFC阴极同步短程硝化反硝化工艺的性能,将双室曝气阴极MFC与A/O脱氮工艺结合处理人工模拟低碳氮比废水。通过静置运行15 d使得MFC阴极室亚硝态氮得以积累,氨氧化菌得以富集。随即改为连续运行后第21天成功启动同步短程硝化反硝化MFC;阴极出水氨氮浓度为0.3 mg/L,亚硝态氮浓度为15.9 mg/L,硝态氮浓度为0.6 mg/L,亚硝化率达到95%以上,阴极电极自养反硝化去除率达到50%以上,COD去除率达到85%以上。结果表明,将MFC与同步短程硝化反硝化工艺结合,通过阴极室中氧气得电子获得高p H,可以强化同步短程硝化反硝化工艺,完成生物脱氮的同时回收电能,并具有减少外加碱度的优势。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

实验室质量管理体系内部审核的策划

在实施ISO／IEC 17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核策划阶段的关键环节，提出审核范围确定、审核计划和抽样方案制订的质量控制要求，为有序高效地实施内部审核提供了技术方法。     

Characterization of products of ozonolysis of acrylonitrile in liquid phase

In order to elucidate the reaction mechanism of the ozonolysis of acrylonitrile in the liquid phase, characterization of reaction products has been attempted. One of the products, which was volatile, has been found to be formaldehyde by derivatizing with dimedone. The infrared and mass spectra of the derivative corresponded with that of alkylidene dimedone. Three other reaction products were isolated by TLC using silica gel, CHCl₃:MeOH (80:20). These have been tentatively identified as glyoxal, epoxide of acrylonitrile and acetamide from their mass spectra. Based on these findings a reaction pathway for the formation of formaldehyde is proposed to be that described by Criegee.