Evaluation of performance of time-saving extraction devices in the BCR three-step sequential extraction procedure

Two alternative extraction methods--a routine ultrasonic bath and a microwave oven--were developed and optimized for their eventual exploitation in the three-stage sequential extraction procedure proposed by the European Standards, Measurements and Testing (S, M & T) Programme, formerly Bureau Communitaire de Reference (BCR), for the operationally defined speciation of Cd, Cr, Cu, Ni and Zn. The conventional BCR three-stage sequential extraction procedure was modified at each stage, applying ultrasonic or microwave devices in order to shorten the required 16 h of shaking in all three steps. The experimental tests and the optimization of the operating parameters were carried out on a highly homogenized estuarine sediment reference material (RM S7) prepared by the Joint Research Centre (JRC) of ISPRA. Extractable metal contents were measured by inductively coupled plasma-mass spectrometry (ICP-MS) and the results obtained in each fraction by all three methods were statistically compared for all the studied elements. The conventional and newly developed alternative extraction methods were finally compared by the analysis of BCR 601, which is certified for the three-step BCR sequential extraction procedure. According to the statistical evaluation of the results, the proposed accelerated sequential extraction methods are valid alternatives to conventional shaking, with much shorter extraction times.     

Fractionation and ecotoxicological implication of potentially toxic metals in sediments of three urban rivers and the Lagos Lagoon,Nigeria, West Africa

The potential environmental impact of sediment-bound Cd, Cr, Cu, Pb and Zn in three trans-urban rivers in Lagos state and in the Lagos Lagoon was assessed by use of the modified Community Bureau of Reference (BCR) sequential extraction. The quality of the data was checked using BCR CRM 143R and BCR CRM 701. Good agreement was obtained between found and certified/indicative values. Of the rivers, the Odo-Iyaalaro, was generally the most contaminated and the Ibeshe the least. Higher concentrations of metals were generally found in the dry season compared to the wet season. Cadmium and Zn were released mostly in the acid exchangeable step of the sequential extraction, indicating that they have the greatest potential mobility and bioavailability of the analytes studied. Chromium and Cu were associated mainly with the reducible and oxidisable fractions, and Pb predominantly with the reducible and residual fractions. Sediments with the highest pseudototal analyte concentrations also released higher proportions of analytes earlier in the sequential extraction procedure. The study suggests that, during the dry season, potentially toxic metals (PTM) may accumulate in sediments in relatively labile forms that are released and can potentially be transported or bioaccumulate in the rainy season. Application of risk assessment codes and Hankanson potential risk indices indicated that Cd was the element of greatest concern in the Lagos Lagoon system. The study indicated that there is a need to strengthen environmental management and pollution control measures to reduce risk from PTM, but that even relatively simple strategies, such as seasonal restrictions on dredging and fishing, could be beneficial.     

Comparison of three sequential extraction protocols for the fractionation of potentially toxic metals in coastal sediments

In the determination of the best sequential extraction procedures (SEP) for the speciation of metals in sediment samples from the Lagos lagoon system, three sequential extraction procedures were compared for the fractionation of Cd, Cr, Cu, Pb, and Zn. The SEP compared included a modified Tessier??s procedure carried out in five steps, while the two other procedures were the three-step original Community Bureau of Reference (BCR) and the modified BCR techniques (four steps). Quantification of the metal concentration was achieved with a flame atomic absorption spectrophotometer. The results obtained by the three methods were compared, and the modified BCR and Tessier SEP were found to extract more Cu, Cr, Pb, and Zn in the reducible phase and therefore a decrease in the oxidizable phase than the original BCR SEP. The most mobile elements were found to be Cd, Pb, and Zn. These are of environmental concern, as these potentially toxic metals could be easily released into the aquatic environment with consequent ingestion by aquatic organisms, thereby entering the food chain. The mass balance (percent recovery) was found to be between 85% and 115% in most cases. Prior to the comparison, the analytical performance of the laboratory was tested using a secondary reference material, GLAURM, using the three-step modified BCR procedure. The results showed high reliability of the analytical performance of the laboratory for all the metals considered.     

Improvement of the BCR three step sequential extraction procedure prior to the certification of new sediment and soil reference materials

The Standards, Measurements and Testing Programme (formerly BCR) of the European Commission proposed a three-step sequential extraction procedure for sediment analysis, following extensive expert consultations and two interlaboratory studies. This scheme was recently used to certify the extractable trace element contents of a sediment reference material (CRM 601). Although this procedure offers a means to ensure the comparability of data in this field, some difficulties concerning the interlaboratory reproducibility still remain, and a new project is currently being conducted to determine the causes of poor reproducibility in the extraction scheme. The final objective of the project is the certification of new sediment and soil reference materials for their extractable contents of Cd, Cr, Cu, Ni, Pb and Zn. This paper presents the results of a small-scale interlaboratory study, which aimed to test a revised version of the extraction schemes by comparing the original and the modified protocols using the CRM 601 sample. This work offers an improvement to the BCR sequential extraction procedure through intercomparison exercises. This improved procedure will allow the obtaining of CRMs to validate analytical data in the analysis of soils and sediments, and it will also facilitate comparability of data in the European Union.     

Mobility and ecological risk assessment of trace metals in polluted estuarine sediments using a sequential extraction scheme

The three-stage sequential extraction procedure for the fractionation of Cd, Cr, Cu, Ni, Pb, and Zn, proposed by the Commission of the European Communities Bureau of Reference, was applied to sediment five samples collected from the Sal estuary, Sergipe State, northeast Brazil, in September 2009. The method showed satisfactory recoveries, detection limits, and standard deviations for determinations of trace metals in the sediments. Cd and Pb were the metals most prevalent in the bioavailable fractions (carbonates, Fe and Mn oxides, organic matter, and sulfides), while Ni, Zn, Cu, and Cr showed higher percentages in the inert fraction. The order of mobility of the metals was Cd (66 %) > Pb (65 %) > Zn (59 %) > Ni (57 %) = Cr (57 %) > Cu (56 %). Possible toxicity related to these metals was examined using the risk assessment code, and by comparing the chemical data with sediment quality guideline ERL-ERM values. Results obtained using the two methods were in agreement, and showed low to medium risk for all metals, indicating that adverse effects on aquatic biota should rarely occur.     

Application of a modified BCR sequential extraction (three-step) procedure for the determination of extractable trace metal contents in a sewage sludge amended soil reference material (CRM 483), complemented by a three-year stability study of acetic acid and EDTA extractable metal content

This paper provides additional data on a sewage sludge amended soil certified reference material, CRM 483, which was certified in 1997 for its EDTA and acetic acid extractable contents of some trace metals, following standardised extraction procedures. The additional work aimed to test the long-term stability of the material and the applicability of an improved version of the BCR three-step sequential extraction procedure on the sewage sludge amended soil (CRM 483). The paper demonstrates the CRM 483 long-term stability for EDTA and acetic acid extractable contents of Cd, Cr, Cu, Ni, Pb and Zn and gives the results (obtained in the framework of an interlaboratory study) for the extractable contents of the same elements in the CRM 483, following the BCR three-step sequential extraction scheme. The aqua regia extractable contents following the ISO 11466 Standard are also given. The data are given as indicative (not certified) values.     

Speciation and assessment of heavy metals in surface sediments of Jinjiang River tidal reach, southeast of China

The concentration and speciation of heavy metals (Cr, Ni, Cu, Zn, Cd, Pb) in surface sediments (??≤ 63 μm) of Jinjiang River tidal reach are determined to evaluate the metal behavior. A modified BCR three-step sequential extraction procedure is carried out, and the residual fraction is undertaken by microwave-assisted acid digestion. The index of geo-accumulation indicates that Cd appeared highest among all these heavy metals in surface sediments, Cr, Cu, Zn lower, and Ni, Pb the least. The percentage of Zn, Cd is comparatively higher in the acid soluble fraction, Pb and Cu higher in the reductive fraction, indicating larger potential danger to the environment. So it is essential for developing the future remediation plans and pollution control strategies.     

Risk assessment of trace metals in an extreme environment sediment: shallow,hypersaline, alkaline,and industrial Lake Acıgöl,Denizli, Turkey

The major and trace element component of 48 recent sediment samples in three distinct intervals (0–10, 10–20, and 20–30 cm) from Lake Ac?göl is described to present the current contamination levels and grift structure of detrital and evaporate mineral patterns of these sediments in this extreme saline environment. The spatial and vertical concentrations of major oxides were not uniform in the each subsurface interval. However, similar spatial distribution patterns were observed for some major element couples, due mainly to the detrital and evaporate origin of these elements. A sequential extraction procedure including five distinct steps was also performed to determine the different bonds of trace elements in the <?60-μ particulate size of recent sediments. Eleven trace elements (Ni, Fe, Cd, Pb, Cu, Zn, As, Co, Cr, Al and Mn) in nine surface and subsurface sediment samples were analyzed with chemical partitioning procedures to determine the trace element percentage loads in these different sequential extraction phases. The obtained accuracy values via comparison of the bulk trace metal loads with the total loads of five extraction steps were satisfying for the Ni, Fe, Cd, Zn, and Co. While, bulk analysis results of the Cu, Ni, and V elements have good correlation with total organic matter, organic fraction of sequential extraction characterized by Cu, As, Cd, and Pb. Shallow Lake Ac?göl sediment is characteristic with two different redox layer a) oxic upper level sediments, where trace metals are mobilized, b) reduced subsurface level, where the trace metals are precipitated.     

Comparison of three sequential extraction procedures for partitioning of heavy metals in car park dusts

The aim of this study was to elucidate the amount of metal released at each step by using different extractants in three sequential extraction schemes for the partitioning of metal contents of car park deposited dust samples. For this purpose, three different sequential extraction procedures (SEP) were employed for the metal fractionation in car park dust samples collected from the campus of Erciyes University, Kayseri, Turkey. While two of the sequential extraction procedures contain five steps the other, namely the BCR sequential extraction scheme, has three steps. The first two methods fractionate metals to be exchangeable, bound to carbonates, bound to Mn oxides, bound to Fe oxides and bound to organic matter, and the BCR protocol fractionates the metals as acid soluble and exchangeable, reducible, and oxidisable. Determination of the metals Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb and Zn was performed by flame atomic absorption spectrometry (FAAS). The results obtained by the three methods were compared and showed that the amount of metal released at each step of the leaching procedure depended both on the type of reagents used and the sequence in which they were applied. The most mobile elements were Cd, Pb and Zn which are metals potentially toxic to the environment and are also known to originate from traffic. The calculated enrichment factors for Cd and Pb were substantially high (73.5-187 and 18.4-27.5, respectively) and somewhat lower for Zn (5.1-6.8). These results confirm that they are important metal pollutants for car parks. Detection limits and recoveries were found in the range of 0.01-1.39 microg ml(-1) and 68-126%, respectively, for the metals studied and the three sequential extraction procedures.     

Comparison of unmodified and modified BCR sequential extraction schemes for the fractionation of heavy metals in shrimp aquaculture sludge from Selangor, Malaysia

A study was carried out to investigate the fractionation of Cd, Cr, Cu, Fe, Mn, Pb, and Zn in shrimp aquaculture sludge from Selangor, Malaysia, using original (unmodified) and modified four-steps BCR (European Community Bureau of Reference, now known as the Standards Measurements and Testing Program) sequential extraction scheme. Step 2 of the unmodified BCR procedure (subsequently called Method A) involves treatment with 0.1 M hydroxylammonium chloride at pH 2, whereas 0.5 M hydroxylammonium chloride at pH 1.5 was used in the modified BCR procedure (subsequently called Method B). Metal analyses were carried out by flame atomic absorption spectrometry. A pseudo-total aqua-regia digest of BCR CRM 701 has also been undertaken for quality assurance purposes. The recovery of Method A for all metals studied ranges from 96.14% to 105.26%, while the recovery for Method B ranges from 95.94% to 122.40%. Our results reveal that Method A underestimated the proportion of metals bound to the easily reducible fraction except for copper. Therefore, the potential mobility of these elements is higher than others. Thus, to use this sludge as a fertilizer we have to first find a remediation for reduction of heavy metal contamination.     

Effect of ultrasonic agitation on the release of copper, iron, manganese and zinc from soil and sediment using the BCR three-stage sequential extraction

An ultrasonic bath and an ultrasonic probe have been used to develop rapid versions of the three-stage Community Bureau of Reference (BCR, now the Standards, Measurement and Testing Programme) sequential extraction procedure. The effect of the ultrasonic treatments on the extraction of copper, iron, manganese and zinc from a sewage sludge-amended soil has been assessed. Recoveries similar to those of conventional shaking (i.e., conventional value, +/- 30%) could generally be obtained for copper, manganese and zinc, but not for the important matrix element iron. With the use of compromise sonication conditions, steps 1, 2 and 3 of the sequential extraction (excluding the hydrogen peroxide digestion in step 3, which was not performed with sonication) could be completed in 3, 5 and 1 min, respectively, using the ultrasonic probe, and in 3, 1 and 1 h, respectively, using the bath. The extraction procedures developed using the soil performed well when applied to lake sediment BCR CRM 601. Analyte partitioning was generally similar to that obtained with mechanical shaking, and overall metal recoveries were 84-98% of those obtained with the conventional BCR protocol, except for copper extracted with the probe (74%). Poorer performance (analyte recoveries, 58-104%) was obtained when the methods were applied to an intertidal sediment. This highlights the difficulty of developing a version of the BCR extraction, with ultrasonic assistance, which gives a performance equivalent to conventional shaking when applied to different substrates.     

北方某水库表层沉积物重金属的赋存形态及其环境影响因子分析

为了解北方某水库重金属污染状况,采用BCR连续提取法对该水库表层沉积物中Cu、Pb、Zn、Cd的赋存形态进行了分析,对其含量及空间分布进行了研究,结合重金属总量讨论了各元素的潜在环境风险。结果表明,该水库表层沉积物中Cu、Pb、Zn、Cd的平均质量比分别为65.20 mg/kg、36.69 mg/kg、137.5 mg/kg、2.38 mg/kg,与该地区土壤元素背景值、该地区水系沉积物平均值及全国水系沉积物平均值相比,4种重金属元素均有一定程度的累积,其中Cd累积最为严重。形态分析结果表明,Cd主要以醋酸可提取态及可还原态存在,具有很高的环境风险;Pb主要以极高比例的可还原态存在,潜在风险较高;Zn和Cu存在较大比例的酸可提取态及可还原态,也具有一定程度的潜在风险。各元素生物有效性即可提取态含量排序为:Cd>Cu>Pb>Zn。     

Investigation of trace elements in agricultural soils by BCR sequential extraction method and its transfer to wheat plants

In this study, soil samples were collected from Edirne, Turkey in both summer and winter seasons and subjected to the modified Community Bureau of Reference (BCR) sequential extraction procedure in order to investigate the chemical partitioning of metals in soils and to predict heavy metals uptake by wheat grains which grown at the same soils. The samples were subjected to a three stage extraction procedure proposed by the BCR. The three phases that were separated out in the following order: (1) carbonate, exchangeable, (2) Fe?CMn oxides, and (3) organic matter. Metal concentrations of soil fractions and grain samples were determined by inductively coupled plasma atomic emission spectroscopy. The wheat samples were prepared to analysis using microwave acid digestion procedure. The pseudo-total concentrations of metals were determined after aqua regia digestion. The analytical accuracy of the method was evaluated by using the Standard Reference Materials (BCR 142R Light Sandy Soil, NIST 2711 Montana Soil, and NIST 2704 Buffalo River Sediment). The sum of the metal contents obtained from the modified BCR sequential extraction procedure and pseudo-total metal contents for soil samples were used to calculate recovery values. In order to evaluate the bioavailability of metals, the relationships between the wheat-metal and soil-extractable metal concentrations were compared.     

The effect of oxidation and acidification on the speciation of heavy metals in sulfide-rich freshwater sediments using a sequential extraction procedure

The speciation of metals in a contaminated, anoxic, sulfide-rich, freshwater sediment was determined experimentally, using a sequential extraction procedure based on the method of Tessier et al. Taking into account the advantages and disadvantages of sequential extractions, the applied methodology allowed the investigation of the influence of aeration and acidification on the distribution of various metals in the sediment. Aeration caused Zn and Cd to be released from sulfides. Carbonates were partly dissolved by the oxidation process, causing mobilisation of Ca. Fe became less mobile owing to a stronger binding to organic matter. The speciation of K, Al, Ni, Pb and Mn and to a lesser extent of Cu was not affected by aeration. As a result of acidification of the aerated sediment, Ca, Mn, Ni, Zn and Cd became more mobile owing to the dissolution of carbonates.     

Certification of the extractable contents of Cd, Cr, Cu, Ni, Pb and Zn in a freshwater sediment following a collaboratively tested and optimised three-step sequential extraction procedure

Sequential extraction procedures have been used during the last decades to study and determine trace element mobility in aquatic sediments. However, the results obtained are operationally defined and, therefore, the significance of the analytical results is related to the extraction scheme used. So, there is a need for suitable reference materials for this type of study to enable the validation of the methodologies and to control the quality of the measurements. This paper describes the preparation of a sediment reference material, BCR-701, the homogeneity and stability studies and the analytical work performed for the certification of the extractable contents of some trace elements, following a collaboratively tested and optimised sequential (three-step) extraction procedure. The paper contains all the results and gives the methods used to certify the extractable contents (mass fractions expressed as mg kg-1 on a dry matter basis) of Cd, Cr, Cu, Ni, Pb and Zn in all steps. Moreover, indicative values are given for the aqua regia extractable contents of the six elements in the sediment and the residue obtained after sequential extraction.     

Trace metals in the shells of blue mussels (Mytilus edulis) from the Poland coast of Baltic sea

The Odiel salt marshes (Marismas del Odiel) are an important nature area declared a Biosphere Reserve, but they are greatly affected by pollution from the Odiel River. Surface sediments from this area were analysed using the latest version of the BCR sequential extraction procedure to determine the fractionation of As, Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn among four geochemical phases (acid-soluble, reducible, oxidisable and residual). The total content of each of the metals and As was also determined. The results showed high concentrations of As, Cd, Cu, Pb and Zn, with maximums of 791 mg kg⁻¹ of As, 8.5 mg kg⁻¹ of Cd, 2,740 mg kg⁻¹ of Cu, 1,580 mg kg⁻¹ of Pb and 3,920 mg kg⁻¹ of Zn. The concentrations of Cr, Mn and Ni were low since there are no sources of pollution by them in the area. A comparison of the metal and As levels with the sediment quality guidelines showed that the pollution is sufficient to produce noxious effects in aquatic organisms in most of the Odiel salt marshes. Based on the chemical distribution of the elements, it was found that Cd and Zn were the most mobile (i.e., elements that can pass easily into the water under changing environmental conditions). However, Cr, Fe, Ni and As were present in the greatest percentages in the residual fraction, which implies that these elements are strongly linked to the sediments.     

Distribution,bioavailability, and potential ecological risk of Cu,Pb, and Zn in soil in a potential groundwater source area

In this study, we examined three horizontal and vertical soil profiles along a sewage drainage ditch in order to determine the spatial distribution of Cu, Pb, and Zn in soils and to assess the bioavailability and potential ecological risks associated with these metals in a potential groundwater source area. Results showed that the concentrations of Cu, Pb, and Zn were approximately at background level, suggesting that human activities (industrial and agricultural pollution) had a negligible influence on these metals in soil, and that the concentrations reflected the natural background levels in the study area. Cu, Pb, and Zn concentrations were slightly higher in topsoil (0–20 cm) than deeper in the soil profile. Using a modified BCR sequential extraction method to evaluate the mobility and bioavailability of metals showed that the potential bioavailability sequence of Cu, Pb, and Zn at three depths in the soil profile was in the order Cu?≈?Pb?<?Zn. The potential ecological risk from the metals was evaluated using risk assessment code, and the results suggest that Cu and Zn pose no or low risk, while there is a low or medium risk from Pb. Results from groundwater monitoring showed that the groundwater was not polluted by leaching from soil.     

铅锌冶炼废水处理后沉渣重金属元素特征与环境活性研究

通过扫描电子显微镜与X射线衍射仪分析、BCR法三步连续提取及元素化学分析,对铅锌冶炼废水处理后沉渣中重金属的赋存状态、环境活性进行研究。结果表明,沉渣中主要毒害元素为Zn、Pb、Mn、Cd和Cu,且以非晶态存在,其含量分别为62350、29530、7650、4530和830 mg/kg。渣中Zn和Cd酸可提取态所占比例较大,分别为37.72%和34.44%; Mn的可还原态相对含量很高,达到49.67%;Zn和Pb的可氧化态含量较高,分别占全量的34.16%、34.68%;Pb和Cu的残渣态含量较高,分别占全量的39.72%和61.69%。     

Accumulation and remobilization of metals in superficial sediments in Tianjin, China

The concentrations of Cr, Ni, Cu, Zn, Cd, and Pb in superficial sediment samples collected from three representative sites (Yuqiao Reservoir, Haihe River, and Haihe River Estuary) in Tianjin, North China, were analyzed using various single extraction and sequential extraction procedures to determine their remobilization, extractability, and distribution patterns. Sediments from the Haihe River had higher metal concentrations and geo-accumulation indices, especially for Cd and Zn, than sediments from the other two sites, suggesting that the Haihe River has been heavily influenced by anthropogenic activities. In addition, over 31% and 28.2% of the total Cd in the Haihe River and the Yuqiao Reservoir, respectively, and 18.2% of the total Zn in the Haihe River were found to be associated with the exchangeable form, indicating the significant remobilization of Cd and Zn when compared with Cr and Ni. However, over 98% of the Ni and 78% of the Cr were most closely associated with the residue and oxidizable fractions, which resulted in their becoming environmentally immobile. Based on the Environmental Protection Agency method 3050B, Cd and Zn had the greatest extraction efficiency when a single extraction procedure using 0.5-mol L^???1 HCl, 0.43-mol L^???1 HAcO, and 0.05-mol L^???1 ethylene-diamine-tetra-acetic acid was conducted, with extraction yields of up to 72%, 68%, and 56% for Cd and 50%, 49%, and 29% for Zn, respectively, being obtained for the Haihe River sediments. This was followed by the yields of Cu and Pb and, finally, those of unpolluted metals such as Cr and Ni. HCl and acetic acid extraction provided equivalent information for predicting Cd and Zn mobility in the sediments studied and produced suitable results for quick screening.     

Associations of cadmium, zinc, and lead in soils from a lead and zinc mining area as studied by single and sequential extractions

An exploratory study of the area surrounding a historical Pb?CZn mining and smelting area in Zawar, India, detected significant contamination of the terrestrial environment by heavy metals. Soils (n?=?87) were analyzed for pH, EC, total organic matter (TOM), Pb, Zn, Mn, and Cd levels. The statistical analysis indicated that the frequency distribution of the analyzed parameters for these soils was not normal. The median concentrations of metals in surface soils were: Pb 420.21 ?? g/g, Zn 870.25 ?? g/g, Mn 696.70 ?? g/g, and Cd 2.09 ?? g/g. Zn concentrations were significantly correlated with Cd (r?=?0.867), indicating that levels of Cd are dependent on Zn. However, pH, electrical conductivity and total organic matter were not correlated significantly with Cd, Pb, Zn, and Mn. To assess the potential mobility of Cd, Pb, and Zn in soils, single (EDTA) as well as sequential extraction scheme (modified BCR) were applied to representative (n?=?23) soil samples. The amount of Cd, Pb, and Zn extracted by EDTA and their total concentrations showed linear positive correlation, which are statistically significant (r values for Cd, Pb, and Zn being 0.901, 0.971, and 0.795, respectively, and P values being <0.001). The correlation coefficients indicate a strong relation between EDTA-extractable metal and total metal. These results appear to justify the use of ??total?? metal contents as a useful preliminary indicator of areas where the risks of metal excess or deficiency are high. The EDTA extractability was maximum for Cd followed by Pb and Zn in soils from all the locations. As indicated by single extraction, the apparent mobility and potential bioavailability of metals in soils followed the order: Cd ?? Pb >?> Zn. Soil samples were sequentially extracted (modified BCR) so that solid pools of Cd, Zn, and Pb could be partitioned into four operationally defined fractions viz. acid-soluble, reducible, oxidizable, and residual. Cadmium was present appreciably (39.41%) in the acid-soluble fraction and zinc was predominantly associated (32.42%) with residual fraction. Pb (66.86%) and Zn (30.44%) were present mainly in the reducible fraction. Assuming that the mobility and bioavailability are related to solubility of geochemical forms of metals and decrease in the order of extraction, the apparent mobility and potential metal bioavailability for these contaminated soil samples is Cd > Zn > Pb.