Water extraction with CO2 bubbling as pretreatment of melting-furnace fly ash for metal recovery

In Japan, melting-furnace fly ash (MFA) generated from ash melting and gasification/melting plants is considered an “urban mine” due to its high metal content. This study aimed to develop a novel approach to pretreating MFA for metal recovery. Water extraction with CO₂ bubbling was investigated because MFA mainly consists of water-soluble salts containing elements such as Cl, Ca, Na, and K. Instead of acid addition, CO₂ bubbling was applied to maintain the optimal pH for minimizing the release of target metal elements and maximizing the removal of undesirable elements during water extraction. The results revealed that CO₂ bubbling effectively decreased the release of Pb, Zn, and Cd into the treatment water. This was mainly due to coprecipitation with CaCO₃, which was primarily formed by the reaction of Ca²⁺ from the MFA with CO₃ ²⁻ from the CO₂ gas. The bubbling process also helped accelerate the removal of Cl from MFA. Furthermore, the study showed that it is possible to lower the water-to-solid ratio to 5 with only a slight reduction in water extraction effect. Finally, approximately four times the concentration of target metals (rare metals and Cu, Pb, and Zn) was achieved by removing 90% of Cl, 70%–90% of Na and K, and 30%–40% of Ca through water extraction with CO₂ bubbling, resulting in a concentration of target metals that was nearly equal to that of ore.     

粉煤灰-粉煤灰合成沸石对Cs~+的固化

以电厂废弃物粉煤灰为原料、采用碱熔-水热法制备了粉煤灰合成A型沸石(以下简称沸石),再以沸石对溶液中的Cs+进行分离富集,最后在碱激发剂的作用下以粉煤灰和吸附后的沸石制得地聚合物固化体。对固化体的性能进行了评价,并探讨了固化机理。实验结果表明:在吸附温度25℃、初始Cs+质量浓度100 mg/L、固液比10.0 g/L的条件下,沸石对的Cs+的吸附率达98%,比粉煤灰提高了2倍以上;沸石掺量为20%~30%(w)时,固化体的抗压强度符合GB 14569.1—2011要求,固化体中Cs+的42 d浸出率和累计浸出分数均远优于GB 14569.1—2011限值,表现出优异的抗浸出性能。     

Chitosan composites reinforced with nanostructured waste fly ash

Journal of Material Cycles and Waste Management - This paper outlines the preparation and characterization of chitosan (CS) composites reinforced with mechano-chemically activated fly ash (MCA-FA)....     

浅谈粉煤灰的资源化利用现状

粉煤灰是电力行业排放的主要固体废弃物,对其的资源化利用已成为环保的首要任务。对粉煤灰进行高附加值的资源化回收利用,是实现可持续发展的必经之路。介绍了大唐国际成功开发研制的从高铝粉煤灰中提取氧化铝技术,开辟了粉煤灰综合利用的新途径。     

Vanadium recovery from oil fly ash by leaching, precipitation and solvent extraction processes

In order to reduce the environmental impact due to land disposal of oil fly ash from power plants and to valorize this waste material, the removal of vanadium was investigated using leaching processes (acidic and alkaline treatments), followed by a second step of metal recovery from leachates involving either solvent extraction or selective precipitation. Despite a lower leaching efficiency (compared to sulfuric acid), sodium hydroxide was selected for vanadium leaching since it is more selective for vanadium (versus other transition metals). Precipitation was preferred to solvent extraction for the second step in the treatment since: (a) it is more selective; enabling complete recovery of vanadate from the leachate in the form of pure ammonium vanadate; and (b) stripping of the loaded organic phase (in the solvent extraction process) was not efficient. Precipitation was performed in a two-step procedure: (a) aluminum was first precipitated at pH 8; (b) then ammonium chloride was added at pH 5 to bring about vanadium precipitation.     

Monitoring the stabilization of municipal solid waste incineration fly ash by phosphation: mineralogical and balance approach

The application of a micro-characterization protocol coupled with a balance approach has allowed the relevant monitoring of a phosphation process for fly ash produced by municipal solid waste incineration. The three main steps of this process consist in removing the salts (chlorides, sulfates) by dissolution at basic pH, phosphation of the residue to trap metals, and its calcination to destroy dioxin-like compounds. The chemical and mineralogical balances compiled on the samples after each step of the process validate these main objectives and highlight the wide phosphorus distribution throughout the sample during the phosphation process, as well as the formation of apatite-type crystallized phosphates. During calcination, the increase in the proportion of crystallized phosphates apatite and whitlockite is largely attributable to the presence of an available calcium source, corresponding to the calcite formed during washing. The metals Pb and Zn, initially distributed in the silicate and carbonate phases, are broadly redistributed in the phosphate neoformations after carbonate dissolution, thus guaranteeing a more permanent stabilization.     

陡河电厂粉煤灰烧结砖生产工艺

结合陡河电厂粉煤灰用于烧结砖的实践，介绍了用粉煤灰生产烧结砖的工艺过程及应该注意的问题。     

Diopside-based glass-ceramics from MSW fly ash and bottom ash

By utilising MSW fly ash from the Shanghai Yuqiao municipal solid waste (MSW) incineration plant as the main raw material, diopside-based glass-ceramics were successfully synthesized in the laboratory by combining SiO(2), MgO and Al(2)O(3) or bottom ash as conditioner of the chemical compositions and TiO(2) as the nucleation agent. The optimum procedure for the glass-ceramics is as follows: melting at 1500 degrees C for 30 min, nucleating at 730 degrees C for 90 min, and crystallization at 880 degrees C for 10h. It has been shown that the diopside-based glass-ceramics made from MSW fly ash have a strong fixing capacity for heavy metals such as lead (Pb), chromium (Cr), cadmium (Cd) etc.     

Wet extraction of heavy metals and chloride from MSWI and straw combustion fly ashes

Fly ash residues from combustion often do not meet the criteria neither for reuse as construction materials nor landfilling as non-hazardous waste, mainly because of the high concentration of heavy metals and chlorides. This work aimed to technically evaluate an innovative wet treatment process for the extraction of chloride (Cl^?), cadmium (Cd), copper (Cu), lead (Pb) and zinc (Zn) from fly ashes from a municipal solid waste incineration (MSWI) plant and from a straw combustion (SC) facility. Factors investigated were liquid/solid (L/S) ratio, full carbonation (CO₂ treatment), influence of pH and leaching time, using a two-level full factorial design. The most significant factor for all responses was low pH, followed by L/S ratio. Multiple linear regression models describing the variation in extraction data had R² values ranging from 58% to 98%. An optimization of the element extraction models was performed and a set of treatment conditions is suggested.     

Chemical stabilization of medical waste fly ash using chelating agent and phosphates: Heavy metals and ecotoxicity evaluation

Chemical stabilization of heavy metals in medical waste fly ash has been carried out using the following compounds: a chelating agent (Ashnite S803), a commercial acidic phosphoric acid solution (Ashnite R303) as well as basic one (Ashnite R201). In order to predict the leachability of heavy metals, Japanese Leaching Test (JLT-13) procedure was applied to the stabilized fly ash products. An ecotoxicity assessment of the stabilized fly ash products leachate and the unstabilized fly ash leachate was conducted using a battery of bioassays based on lettuce root elongation inhibition, Daphnia magna mortality and Vibrio fischeri photoinhibition. The results showed that the three stabilizing agents were able to significantly decrease (ANOVA, P < 0.05) the concentration of heavy metals in the leachates. Although the leachate from both stabilized and unstabilized fly ash were very toxic to lettuce and daphnids, the incorporation of these stabilizing agents diminished significantly (ANOVA, P < 0.05) the toxicity of the leachates towards the three tested organisms. Pearson correlation analysis was used to analyze the strength of the relationship between chemical elements concentration in the leachate and bioassays results. Most of the heavy metals in the leachate were significantly correlated (ANOVA, P < 0.05) with the toxicity values of the bioassays. However, the correlation was not found between the concentration of dissolved organic carbon (DOC) and the toxicity effect of the leachate to the tested organisms.     

Fabrication of bulk materials with zeolite from coal fly ash

After packing a compact of coal fly ash mixed with 3.5?M (mol/L) sodium hydroxide solution into a cylindrical plastic mold at 80?°C and 50?% relative humidity for 24?h, the plastic mold was released and the compact was immersed in 3.5?M sodium hydroxide solution at 80?°C for 48?h. When the resultant compact was removed from the solution and cured at 80?°C and 50?% relative humidity for 7?days, a bulk material with zeolite was formed. The strength of the resultant bulk material was a result of the formation of geopolymer (alkali-activated cement). The specific surface area and the compressive strength of the bulk body sample were 21.4?m²/g and 29.0?MPa, respectively. According to a quantitative analysis conducted using the X-ray diffraction (XRD) technique, the content of the formed Na-P type zeolite was estimated to be approximately 28.2?% in mass ratio. The pore size of the resultant bulk materials with zeolite ranges from sub-nanometer to several tens of nanometers, so the resultant bulk material with zeolite exhibited excellent water vapor retention characteristics.     

Chemical sequential extraction of heavy metals and sulphur in bottom ash and in fly ash from a pulp and paper mill complex

A five-stage sequential extraction procedure was used to determine the distribution of 11 metals (Cd, Cr, Cu, Mo, Pb, Zn, As, Co, V, Ni, Ba), and sulphur (S) in bottom ash and in fly ash from a fluidized bed co-combustion (i.e. wood and peat) boiler of Stora Enso Oyj Oulu Mill at Oulu, Northern Finland, into the following fractions: (1) water-soluble fraction (H2O); (2) exchangeable fraction (CH3COOH); (3) easily reduced fraction (NH2OH-HCl); (4) oxidizable fraction (H2O2 + CH3COONH4); and (5) residual fraction (HF + HNO3 + HCl). Although metals were extractable in all fractions, the highest concentrations of most of the metals occurred in the residual fraction. From the environmental point of view, this fraction is the non-mobile fraction and is potentially the least harmful. The Ca concentrations of 29.3 g kg(-1) (dry weight) in bottom ash and of 68.5 g kg(-1) (dry weight) in fly ash were correspondingly approximately 18 and 43 times higher than the average value of 1.6 g kg(-1) (dry weight) in arable land in Central Finland. The ashes were strongly alkaline pH (approximately 12) and had a liming effects of 9.3% (bottom ash) and 13% (fly ash) expressed as Ca equivalents (dry weight). The elevated Ca concentrations indicate that the ashes are potential agents for soil remediation and for improving soil fertility. The pH and liming effect values indicate that the ashes also have a pH buffering capacity. From the environmental point of view, it is notable that the heavy metal concentrations in both types of ash were lower than the Finnish criteria for ash utilization.     

Heavy metals removal/stabilization from municipal solid waste incineration fly ash: a review and recent trends

Waste treatment using thermal technologies, such as incineration, leads to the production of pollutants and wastes, including fly ash (FA). Fly ash contains heavy metals (HMs) and other contaminants and can potentially pose high risks to the environment and negatively impact health and safety. Consequently, stabilizing fly ash prior to either use or landfilling is crucial. The toxicity of fly ash through heavy metal leaching can be assessed using leaching tests. The leaching rates of heavy metals primarily depend on the surrounding conditions as well as fly ash properties and metal speciation. Physical separation, leaching or extraction, thermal treatment and solidification/chemical stabilization are proposed as suitable approaches for fly ash treatment. Economic considerations, environmental concerns, energy consumption and processing times can define the efficiency and selection of the treatment approach. This review considers the latest findings and compares the advantages and shortcomings of different fly ash treatment methods with the aim of highlighting the recent advances in the field. The review concludes that the simultaneous implementation of various methods can lead to highly efficient heavy metals removal/stabilization while simultaneously taking economic and environmental considerations into account.

     

Remediation of fly ash landfills through plantation

In India, a significant area of land is occupied by preexisting coal‐fired thermal power plants (TPPs) for the storage of fly ash slurry in ash ponds. However, the area available for storage of fly ash at these TPPs is limited. In addition, this type of fly ash disposal poses a problem due to restricted land availability and potential contamination issues. A viable alternative is the reclamation of fly ash ponds by plantation. A study at the Ramagundam Super Thermal Power Station (RSTPS) in Andhra Pradesh, India, on reclamation of a portion of an ash‐filled, low‐lying area has been performed. This article describes the characteristics of the RSTPS pond ash, ash leachates, and improvements in the fertility status of the reclaimed area over a three‐year period. Furthermore, morphometric observations of different planted species indicate that these types of ash‐filled, low‐lying areas can be suitably reclaimed and the nutrient‐rich leachate from ash‐filled areas potentially can be used for irrigation purposes. © 2008 Wiley Periodicals, Inc.     

粉煤灰在废水处理中的应用

就粉煤灰处理废水的研究与应用现状进行了综述.粉煤灰主要通过其吸附作用(物理吸附和化学吸附)处理废水,对于城市污水、工业废水、含重金属离子、F-、PO3-4废水等均有较好的处理效果.对粉煤灰进行物理或化学改性研制高效复合粉煤灰混凝剂是提高粉煤灰利用价值的有效途径之一.同时,提高粉煤灰吸附容量以及妥善处理吸附饱和灰是当前急需解决的问题.     

Use of flue gas desulphurisation (FGD) waste and rejected fly ash in waste stabilization/solidification systems

Stabilization/solidification (S/S) processes have been used as the final treatment step for hazardous wastes prior to land disposal. Fly ash is a by-product of coal-fired power generation; a significant proportion of this material is low-grade, reject material (rFA) that is unsuitable as a cement replacement due to its high carbon content and large particle size (>45 microm). Flue gas desulphurization (FGD) sludge is a by-product from the air pollution control systems used in coal-fired power plants. The objective of this work was to investigate the performance of S/S waste binder systems containing these two waste materials (rFA and FGD). Strength tests show that cement-based waste forms with rFA and FGD replacement were suitable for disposal in landfills. The addition of an appropriate quantity of Ca(OH)2 and FGD reduces the deleterious effect of heavy metals on strength development. Results of TCLP testing and the progressive TCLP test show that cement-rFA-Ca(OH)2 systems with a range of FGD additions can form an effective S/S binder. The Leachability Index indicates that cement-based waste forms with rFA replacement were effective in reducing the mobility of heavy metals.     

Effect of the milling solution on lead stabilization in municipal solid waste incinerator fly ash during the milling processes

The wet milling process had been found to effectively stabilize lead in fly ash. This study adopts this method and looks at the effect of different milling solutions to improve the efficiency of lead stabilization. Different milling solutions (water, phosphoric acid and ethanol) and different milling times (1, 24, 48 and 96 h) were selected as parameters. Since lead oxide can be identified by XRD in this experiment’s samples, 5% lead oxide was added to the extracted mixed fly ash to make instrumental analysis easier. The experimental results indicate that the effect of stabilization of lead after milling could exceed 96%. During milling with water, considerable lead leached into the water in the initial stage (1 h) of the process, but a stable level was reached as the milling time increased. After milling with ethanol and 0.2 M phosphoric acids, the efficiency could exceed 93% after 1 h of milling time. The results of the sequential extraction procedure (SEP) results show that the residual fraction could be increased from 8.93% to 56.16% when a 0.2 M phosphoric acid solution was used. Clearly the choice of an appropriate milling solution can enhance lead stabilization in the fly ash.     

Comparative study on the characteristics of fly ash and bottom ash geopolymers

This research was conducted to compare geopolymers made from fly ash and ground bottom ash. Sodium hydroxide (NaOH) and sodium silicate (Na(2)SiO(3)) solutions were used as activators. A mass ratio of 1.5 Na(2)SiO(3)/NaOH and three concentrations of NaOH (5, 10, and 15M) were used; the geopolymers were cured at 65 degrees C for 48 h. A Fourier transform infrared spectrometer (FT-IR), differential scanning calorimeter (DSC), and scanning electron microscope (SEM) were used on the geopolymer pastes. Geopolymer mortars were also prepared in order to investigate compressive strength. The results show that both fly ash and bottom ash can be utilized as source materials for the production of geopolymers. The properties of the geopolymers are dependent on source materials and the NaOH concentration. Fly ash is more reactive and produces a higher degree of geopolymerization in comparison with bottom ash. The moderate NaOH concentration of 10 M is found to be suitable and gives fly ash and bottom ash geopolymer mortars with compressive strengths of 35 and 18 MPa.     

New technology and application of brick making with coal fly ash

China has ranked first in the coal fly ash emission in the world. The multipurpose use of the fly ash from power plant waste is always an important topic for the Chinese environmental protection, which has drawn the concern of the government, scientific research departments, manufacturing enterprises and industry experts. This paper introduces an experimental research on how to recycle fly ash effectively, a kind of new technology of making bricks by which fly ash content could be amounted to 50–80 %. The article introduces raw materials of fly ash brick, production process and key control points. It introduces how to change the technical parameters of the existing brick-making mechanical device, optimize the parameters combination and improve the device performance. High-content fly ash bricks are manufactured, which selects wet fly ash from power plants, adding aggregate with reasonable ratio and additives with reasonable dosage, and do the experimental research on manufactured products for properties, production technology and selection about technology parameters of production equipment. All indexes of strength grade, freezing-thawing resisting, and other standards of the studied bricks reached the national standards for building materials industry.