TiO2/AC催化臭氧氧化处理水中的苯酚

研究了单独臭氧氧化及以活性炭(AC)和负载二氧化钛的活性碳(TiO2/AC)为催化剂催化臭氧氧化处理水中苯酚的效果。考察了AC、TiO2/AC对苯酚的吸附特性及三种方法对苯酚的转化率及矿化率效果及其臭氧利用效率,并对氧化过程进行了动力学分析。实验结果表明:AC、TiO2/AC对苯酚的吸附均较好地符合Freundlich方程;催化臭氧氧化转化苯酚的效果高于单独臭氧氧化;TiO2/AC作催化剂有利于苯酚的最终矿化,同时提高了臭氧的利用效率;3种氧化反应均较好的符合二级动力学方程,TiO2/AC催化臭氧氧化苯酚的二级动力学常数为0.0001L/(mg.min),高于单独臭氧氧化0.00004L/(mg.min)和AC催化臭氧氧化0.00006L/(mg.min)。     

Inactivated properties of activated carbon-supported TiO2 nanoparticles for bacteria and kinetic study

The activated carbon-supported TiO₂ nanoparticles (TiO₂/AC) were prepared by a properly controlled sol-gel method. The effects of activated carbons (AC) support on inactivated properties of TiO₂ nanoparticles were evaluated by photocatalytic inactivation experiments of Escherichia coli. The key factors affecting the inactivation efficiency were investigated, including electric power of lamp, temperature, and pH values. The results show that the TiO₂/AC composites have high inactivation properties of E. coli in comparison with pure TiO₂ powder. The kinetics of photocatalytic inactivation of E. coli was found to follow a pseudo-first order rate law for TiO₂/AC composites, and kinetic behavior could be described in terms of a modified Langmuir-Hinshelwood model. The values of the adsorption equilibrium constants for the bacteria, K_c, and for the rate constants, k_r, were certainly depended on TiO₂ content. At 47 wt.% TiO₂ coatings with the highest rate constant, the K_c and k_r were 1.17 × 10⁻⁸L/cfu and 1.43 × 10⁶ cfu/(L·min), respectively. The variety of parameters shows significant effects on inactivation rate. The outer layer of bacteria decomposed first resulting in inactivation of cell, and with further illumination, the cells nearly decomposed.     

Preparation and performance of photocatalytic regenerationable activated carbon prepared via sol-gel TiO2

Preparation of photocatalytic regenerationable activated carbon （AC） is the key step for the practical application of in situ regeneration of exhausted AC. A novel photocatalytic regenerationable AC was prepared by sol-gel TiO2 in this work. The adsorption and regeneration performance of TiO2/AC were evaluated using phenol as model compound. Scanning electron microscope （SEM） and nitrogen （77 K） adsorption isotherm were used to determine the surface area, pore structure and the distribution of TiO2. The results showed that with the increase of TiO2 loading, adsorption capacity of TiO2/AC decreased and the regeneration efficiency increased. The photocatalytic regenerationable AC with suitable TiO2 loading （2 wt%） exhibited suitable adsorption capacity and regeneration efficiency. TiO2 located mainly in the entrance of macro-pore of carbon. The prepared TiO2/AC exhibited similar surface structure and pore structure with material carbon.     

超临界乙醇流体制取活性炭-TiO2光催化剂复合材料的研究

研究表明：在超临界乙醇流体介质下钛酸异丙酯能有效地分解成具光催化活性的锐钛矿型TiO2粒子，同时产生的TiO2粒子可与活性炭融合成一体，形成的活性炭－TiO2光催化剂复合材料具很好的光催化活性与吸附作用，而且具有的协同效应优于活性炭与TiO2样品的物理混合形式。     

Fe-Ni-TiO2/AC粒子电极的制备及可见光光电催化协同降解RhB

制备Fe-Ni-TiO2/AC粒子电极,应用于可见光助三维电极/电Fenton(Vis-3D/EF)光电催化体系中,以RhB为目标污染物,研究了可见光光电催化对RhB的协同降解.实验优化了Fe-Ni-TiO2/AC粒子电极的制备条件,并与活性炭粒子电极、活性炭负载TiO2粒子电极在Vis-3D/EF体系中的光电催化性能进行对比,结果表明:TiO2浸渍液浓度为2g/L,Fe-Ni掺杂比为5:5,Fe:Ni:TiO2物质的量比为0.5:0.5:100的条件下制备的粒子电极在Vis-3D/EF体系中表现出最优的光电催化性能,60min对RhB的去除率达92.58%,优于活性炭粒子电极和活性炭负载TiO2粒子电极.自制粒子电极在Vis-3D/EF体系比在3D/EF体系对RhB的去除率提高29.46%,表现出明显的光催化和三维电极/电Fenton协同处理效果,协同指数为1.18,说明了自制粒子电极应用在Vis-3D/EF组合技术中,实现对RhB的可见光光电协同降解是可行的.     

Activated carbon supported TiO2-photocatalysis doped with Fe ions for continuous treatment of dye wastewater in a dynamic reactor

Fe-doped TiO2 coated on activated carbon (Fe-TiO2/AC, FTA) composites were prepared by an improved sol-gel method and characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, X-ray di ractometry, inductively coupled plasma mass spectrometry and BET surface area analysis. Obtained FTA composites were applied to the continuous treatment of dye wastewater in a dynamic reactor. The e ects of Fe ion content, catalyst content, UV-lamp power and flowrate of the continuous treatment of dye wastewater on degradation e ciency were analyzed to determine the optimum operating conditions of dye wastewater degradation. Continuous photocatalytic experiments provided interesting results that FTA had a high chemical oxygen demand (COD) removal rate compared with TiO2, Fe doped TiO2 (FT) and TiO2 coated on activated carbon (TA). In particular, when using the FTA catalyst with a Fe ion content of 0.33%, the kinetic content (k = 0.0376) of COD removal was more than the sum of both TA (0.0205) and 0.33% FT (0.0166). FTA showed a high photoactivity because of a synergistic e ect between Fe ions and AC on TiO2, which is higher than the individual e ects of AC or Fe ions on TiO2. Additionally, for the photocatalytic degradation of dye wastewater, the optimum Fe ion content, catalyst content, UV-lamp power and flowrate were 0.33%, 6 g/L, 60 W (two lamps) and 300 mL/hr, respectively. An investigation of catalyst reuse revealed that the 0.33% FTA showed almost no deactivation in photocatalytic degradation of naturally treated wastewater.     

活性炭负载TiO2催化剂对直接耐酸大红4BS溶液的光催化降解研究

采用溶胶-凝胶法制备了活性炭负载型TiO2催化剂,采用了XRD、BET和SEM对催化剂进行表征。研究了催化剂对直接耐酸大红4BS的紫外光催化降解,比较了活性炭、P25和TiO2／AC对4BS溶液的降解能力,探讨了催化剂煅烧温度和投加量以及染料溶液的初始浓度对光催化降解率的影响,并对催化剂进行了回收再生实验。结果表明,500℃下煅烧的TiO2／AC催化剂比表面积为1147．88m^2／g、TiO2粒径为21．9nm、晶相组成以锐钛矿为主,具有良好的光催化活性和稳定性;90min后2g／L催化剂对150mg／L的4BS溶液紫外光催化降解率达到99．8％。     

静电纺丝制备TiO2／PAN纳米纤维毡及其性能研究

采用超声波水解技术水解TiCl4制备纳米TiO2粒子,与聚丙烯腈（PAN）的N,N-二甲基甲酰胺（DMF）溶液共混后,通过静电纺丝制得具有光催化活性的TiO2／PAN纳米纤维毡,并用其对模拟废水中苯酚进行光催化降解实验。X射线衍射（XRD）表征结果显示制备的TiO2为锐钛矿。用场发射扫描电镜（FE—sEM）观察纤维毡的形态,显示纤维的直径随纺丝液浓度增大而增大。对苯酚进行光催化降解结果表明：纺丝液浓度质量分数为5％TiO2／PAN纤维毡对苯酚的降解率最高,对100mg／L,50mg／L和20mg／L苯酚的降解率分别为51．1％,87．5％和99．6％。纤维毡循环使用5次后对于20mg／L苯酚的降解率为87．4％。     

鲤鱼对纳米二氧化钛的生物富集

建立了浓硫酸-硫酸铵酸化消解-ICP测定水样及鱼样中纳米二氧化钛的方法,并研究了纳米二氧化钛在鲤鱼(Cyprinus carpio)体内的富集.酸化消解-ICP测定方法对20.0 mg/L纳米二氧化钛水样,测定的相对标准偏差仅为4.53%.纳米二氧化钛在水样和鱼样中的加标回收率分别为94%～104%和90%～103%,可以精确测定环境样品中纳米二氧化钛浓度.纳米二氧化钛在鱼体内有较高的富集,暴露于3 mg/L、10 mg/L纳米二氧化钛悬浮液的鲤鱼,25 d时鱼体内的二氧化钛浓度分别达到2.1 mg/g和5.8 mg/g.达到平衡时,BCF分别为675.5和595.4.纳米二氧化钛在鱼鳃、内脏中有很大程度的富集,肌肉部分对纳米二氧化钛的富集最少.     

Impact of density of coating agent on antibacterial activity of silver nanoparticle impregnated plasma treated activated carbon

To use stabilized nanoparticles(NPs) in water as disinfectants over a very long period, the amount of coating agent(for NP stabilization) needs to be optimized. To this end, silver nanoparticles(Ag-NPs) with two different coating densities of tri-sodium citrate(12.05 and46.17 molecules/nm~2, respectively), yet of very similar particle size(29 and 27 nm, respectively)were synthesized. Both sets of citrate capped NPs were then separately impregnated on plasma treated activated carbon(AC), with similar Ag loading of 0.8 and 0.82 wt.%, respectively. On passing contaminated water(containing 10~4 CFU Escherichia coli/m L of water) through a continuous flow-column packed with Ag/AC, zero cell concentration was achieved in 22 and 39 min, with Ag-NPs(impregnated on AC, named as Ag/AC) having lower and higher coating density, respectively. Therefore, even on ensuring similar Ag-NP size and loading, there is a significant difference in antibacterial performance based on citrate coating density in Ag/AC.This is observed in lower coating density case, due to both:(i) higher Ag~+ ion release from Ag-NP and(ii) stronger binding of individual Ag-NPs on AC. The latter ensures that, Ag-NP does not detach from the AC surface for a long duration. TGA-DSC shows that Ag-NPs with a low coating density bind to AC with 4.55 times higher adsorption energy, compared to Ag/AC with a high coating density, implying stronger binding. Therefore, coating density is an important parameter for achieving higher antibacterial efficacy, translating into a faster decontamination rate in experiments, over a long period of flow-column operation.     

Zr/TiO2纳米颗粒的制备及其光催化活性

以钛酸丁酯,乙醇为原料,用固相合成法制备了Zr/TiO2纳米颗粒,用XRD、TEM对其组成、颗粒大小、形貌进行了表征.通过对罗丹明B的降解反应,考察了Zr/TiO2的光催化活性.结果表明,Zr/TiO2为纳米颗粒,平均粒径为12.7 nm左右,且颗粒均匀;掺杂金属离子Zr提高了TiO2光催化效率,掺杂2.0%Zr的催化剂活性最高.Zr/TiO2的光催化反应,首先是反应物在Zr/TiO2表面发生吸附作用,然后进一步发生光催化降解.     

TiO2/AC复合光催化剂的研究进展

多孔材料与纳米TiO2复合是目前光催化领域的研究热点.多孔材料作为吸附中心可为TiO2光催化剂提供高浓度反应环境,提高催化剂矿化效率并抑制催化剂失活、解决催化剂分离等难题;目前,国内外研究者对TiO2/AC(活性炭)的光催化机理、TiO2与AC的协同作用机理、TiO2/AC的制备方法进行了较为深入的研究.对TiO2/A...     

混晶纳米TiO_2的制备及其光催化降解有毒有机污染物

以无定形TiO2沉淀为前驱体,在水热条件下得到了含板钛矿(121)相混晶纳米TiO2,考察了水热反应的温度和时间等因素对含板钛矿型TiO2光催化活性的影响.采用XRD、TEM对制备的TiO2进行初步表征,并结合光催化(λ≤387 nm)降解有机染料的光活性探针反应.结果表明,水热温度为150℃,时间为24 h时,可制得具有较高光催化活性的纳米TiO2,其纳米尺寸为14.20 nm,板钛矿相含量63.6%,锐钛矿含量为36.4%.光催化实验中跟踪研究了其对染料酸性桃红(sulforhodmineB,SRB)的褪色及2,4-DCP的降解情况,并对降解中间产物H2 O2、.OH进行跟踪测定,实验结果表明板钛矿相混晶TiO2的光催化主要涉及.OH氧化历程,光照射9 h对SRB和2,4-DCP的矿化氧化分别达到89%和78%,循环5次光催化降解SRB实验,催化剂表现出较好的稳定性,催化性能无明显变化.     

TiO2/PS/Fe3O4 光催化剂的低温制备及其光催化和磁回收性能

以聚苯乙烯(PS)包覆油酸修饰过的纳米Fe3O4为磁核,在低温(90℃)、中性(pH=7左右)条件下,制备了以PS为惰性隔离层的磁载TiO2光催化剂.用X射线衍射仪(XRD)、透射电子显微镜(TEM)、傅里叶红外分光光度计(FT-IR)、振动样品磁强计(VSM)对催化剂的物相组成、形貌、表面性质、磁学性质进行了表征.以苯酚为模拟污染物,考察了其光催化活性,以自制的磁回收装置,考察其回收特性.结果表明,低温制备的TiO2为锐钛矿结构,平均粒径为2～5 nm,催化剂TiO2/PS/Fe3O4[其中物质的量比为n(TiO2)∶n(St)∶n(Fe3O4)=60∶2.5∶1]具有结构完整的壳/壳/核结构,TiO2在PS/Fe3O4表面负载牢固;光催化降解苯酚遵循一级反应动力学方程,TiO2/PS/Fe3O4[n(TiO2)∶n(St)∶n(Fe3O4)=60∶2.5∶1]的反应速率常数K=0.025 8,与纯TiO2的活性接近(K=0.026 2);循环使用5次后,反应速率常数仅降低0.003 4.所制催化剂具有较强的磁感应强度,平均回收率可达到92%以上.该低温水解法制备的磁载TiO2光催化剂具有良好的应用前景.     

Evaluation of the adsorption potential of titanium dioxide nanoparticles for arsenic removal

The adsorption potential of titanium dioxide (TiO2) nanoparticles for removing arsenic from drinking water was evaluated. Pure and iron-doped TiO2 particles are synthesized via sol-gel method. The synthesized TiO2 nanoparticles were then immobilized on ordinary sand for adsorption studies. Adsorption isotherms were conducted on the synthesized nanoparticles as well as the sand coated with TiO2 nanoparticles under varying conditions of air and light, namely, the air-sunlight (A-SL), air-light (AL), air-dark (AD) and nitrogen-dark (ND). X-Ray diffraction (XRD) analysis showed that the pure and the iron-doped TiO2 nanoparticles were in 100% anatase crystalline phase with crystal sizes of 108 and 65 nm, respectively.Adsorption of arsenic on the three adsorbents was non-linear that could be described by the Freundlich and Langmuir adsorption models. Iron doping enhanced the adsorption capacity of TiO2 nanoparticle by arresting its grain growth and making it visible light responsive resulting in a higher affinity for arsenic. Similarly, the arsenic removal by adsorption on the sand coated with TiO2 nanoparticles was the highest among the three types of sand used. In all cases, As(V) adsorbed more compared with As(III). Solution pH appeared to be the most important factor in controlling the amount of arsenic adsorbed.     

纳米Au/TiO2薄膜真空紫外光催化降解甲醛

为提高真空紫外光催化对甲醛的去除率并降低副产物O3的浓度,采用低温吸附法在TiO2薄膜上负载纳米Au.研究比较了UV254nm光催化(TiO2/UV)、真空紫外光降解(VUV)、真空紫外光催化(TiO2/VUV)等3种方法对低浓度甲醛的降解效果.结果表明,TiO2/VUV对甲醛的去除率显著高于VUV和TiO2/UV.TiO2表面负载纳米Au粒子能促进光生电子和空穴的分离.因此,在真空紫外光催化降解过程中, Au/TiO2不仅提高甲醛的降解率,还显著分解副产物臭氧,使尾气臭氧浓度降低32%.而且Au/TiO2薄膜在真空紫外光催化过程中具有很好的稳定性.     

Catalytic decomposition of low level ozone with gold nanoparticles supported on activated carbon

Highly dispersed gold nanoparticles were supported on coal-based activated carbon (AC) by a sol immobilization method and were used to investigate their catalytic activity for low-level ozone decomposition at ambient temperature. Nitrogen adsorption-desorption, scanning electron microscope (SEM), and X-ray photoelectron spectroscopy (XPS) were used to characterize the catalysts before and after ozone decomposition. The results showed that the supported gold nanoparticles prepared with microwave heating were much smaller and more uniformly dispersed on the activated carbon than those prepared with traditional conduction heating, exhibiting higher catalytic activity for ozone decomposition. The pH values of gold precursor solution significantly influenced the catalytic activity of supported gold for ozone decomposition, and the best pH value was 8. In the case of space velocity of 120000 h⁻¹, inlet ozone concentration of 50 mg/m³, and relative humidity of 45%, the Au/AC catalyst maintained the ozone removal ratio at 90.7% after 2500 min. After being used for ozone decomposition, the surface carbon of the catalyst was partly oxidized and the oxygen content increased accordingly, while its specific surface area and pore volume only decreased a little. Ozone was mainly catalytically decomposed by the gold nanoparticles supported on the activated carbon.     

纳米TiO2-光催化灭活水中噬菌体MS2

提出了一种简易的水中病毒灭活方法,以噬菌体MS2为模式病毒,探讨了紫外光照射时间、TiO2浓度、紫外光强度对自来水中MS2灭活效率的影响;评价了太阳光代替紫外光用于光催化灭活病毒的可行性.研究结果表明,聚乙烯(PE)材质的样品袋能更好地透过紫外光;紫外光照射6h,50mg/L的TiO2可以灭活自来水中7.95Log的MS2;紫外光强度在45μW/m2以下时,灭活率随强度的提高而增加;在溪水中,50mg/L的TiO2仅有4.87Log的灭活效率. 在太阳光下,50mg/L的TiO2在自来水和溪水中对MS2的灭活效率差异不明显,都达到了6.1Log以上,表明太阳光-TiO2灭活水中的病毒可行且高效.     

Effect of platinum on the photocatalytic degradation of chlorinated organic compound

TiO2 nanoparticles, doped with di erent Pt contents, were prepared by a modified photodeposition method using Degussa P-25 TiO2, H2PtCl6 6H2O and methanol as the solvents. The physicochemical properties of Pt/TiO2 were investigated by the nitrogen adsorption and desorption isotherm measurement technique, X-ray di raction analysis and photoluminescence spectra, respectively. Reaction rates from photocatalytic removal of dichloromethane over Degussa P-25 TiO2 and Pt/TiO2 were evaluated. The average diameter and BET surface area of the TiO2 catalyst particles were 300 nm and 50 m2/g, respectively. The degradation e ciency was 99.0%, 82.7%, 55.2%, and 57.9% with TiO2 at inlet concentrations of 50, 100, 200, and 300 ppm, respectively. And the degradation e ciency was 99.3%, 79.7%, 76.5%, and 73.4% with a 0.005 wt.% Pt/TiO2 at inlet concentrations of 50, 100, 200, and 300 ppm, respectively. In addition, we found that the photoluminescence emission peak intensities decreased with increases in the doping amount of Pt, which indicates that the irradiative recombination was weakened. Furthermore, the results showed that the UV/0.005 wt.% Pt/TiO2 process was capable of e ciently decomposing gaseous DCM in air.     

表面酸碱2步改性对活性炭吸附Cr(Ⅵ)的影响

研究了酸碱2步改性对活性炭吸附水相中Cr(Ⅵ)的影响.将活性炭(AC₀)在HNO₃溶液中氧化(AC₁),然后在NaOH和NaCl的混合液中处理(AC₂).分别采用平衡和连续吸附试验,测试Cr(Ⅵ)的吸附特征.以Boemh滴定法定量检测活性炭表面酸性官能团数量,结合元素分析结果定量表征活性炭的表面含氧官能团变化;以低温液氮(N₂/77K)吸附法分析活性炭的比表面积和孔径结构.结果表明:活性炭经2步改性后,其Cr(Ⅵ)的吸附容量和吸附速度均显著改变.吸附容量和吸附速度大小依次为AC₂>AC₁>AC₀.改性活性炭表面积下降,表面含氧酸性官能团数量增加.HNO₃液相氧化处理可使活性炭表面生成带正电含氧酸性官能团,第2步改性后活性炭表面酸性官能团H⁺部分被Na⁺取代,使活性炭表面酸性降低.表面较多的含氧酸性官能团(与AC₀相比)、适宜的表面pH(与AC₁相比)是AC₂所表现出较高Cr(Ⅵ)吸附容量的主要原因.