Loofa sponge immobilized fungal biosorbent: a robust system for cadmium and other dissolved metal removal from aqueous solution

The potential of loofa sponge discs to immobilize fungal biomass of Phanerochaete chrysosporium (a known biosorbent) was investigated as a low cost biosorbent for the removal of Cd(II) ions from aqueous solution. A comparison of the biosorption of Cd(II) by immobilized and free fungal biomass from 10 to 500 mg l(-1) aqueous solutions showed an increase in uptake of over 19% when the biomass is immobilized (maximum biosorption capacity of 89 and 74 mg Cd(II) g(-1) biomass for immobilized and free biomass respectively at a solution pH of 6). Equilibrium was established within 1h and biosorption was well defined by the Langmuir isotherm model. The immobilized biomass could be regenerated using 50 mM HCl, with up to 99% metal recovery and reused in ten biosorption-desorption cycles without significant loss of capacity. This study suggests that such an immobilized biosorbent system has the potential to be used in the industrial removal/recovery of cadmium and other pollutant metal ions from aqueous solution.     

Biosorption of copper(II) from aqueous solutions by pre-treated biomass of marine algae Padina sp

Biosorption of heavy metals can be an effective process for the removal and recovery of heavy metal ions from aqueous solutions. The biomass of marine algae has been reported to have high uptake capacities for a number of heavy metal ions. In this paper, the adsorption properties of a pre-treated biomass of marine algae Padina sp. for copper(II) were investigated. Equilibrium isotherms and kinetics were obtained from batch adsorption experiments. The biosorption capacities were solution pH dependent and the maximum capacity obtained was 0.80 mmol/g at a solution pH of about 5. The biosorption kinetics was found to be fast, with 90% of adsorption within 15 min and equilibrium reached at 30 min. The effects of light metal ions on copper(II) uptake were studied and the presence of light metal ions did not affect copper(II) uptake significantly. Fixed-bed breakthrough curves for copper(II) removal were also obtained. This study demonstrated that the pre-treated biomass of Padina sp. could be used as an effective biosorbent for the treatment of copper(II) containing wastewater streams.     

满江红干体对锌离子的生物吸附

以满江红干体为生物吸附剂,研究了不同条件下对废水中Zn²⁺的净化作用。结果表明,满江红干体对Zn²⁺的吸附是一个快速的过程,前5 min的吸附量达到最大吸附量的62.9%,30 min达到吸附平衡;初始pH值对Zn²⁺的吸附有显著的影响,最适pH值为6;随着干体量的增加,吸附率逐渐提高而吸附量则降低;随着Zn²⁺初始浓度的增加,吸附率逐渐降低而吸附量则提高。满江红干体对Zn²⁺的吸附符合Langmuir吸附等温线方程,最大吸附容量达57.5 mg/g。5次吸附解吸循环实验数据表明,重复次数和再生处理对满江红干体的吸附能力没有产生显著影响。因此,满江红干体在处理含Zn²⁺废水中的重复使用是可行的。     

棘孢曲霉(Aspergillus aculeatus)对Pb~(2+)和Cd~(2+)的吸附特征

为了研究棘孢曲霉(Aspergillus aculeatus)对溶液中Pb~(2+)和Cd~(2+)吸附过程的特征,分别从动力学、热力学和吸附等温线三方面进行了实验,同时还研究了pH、温度、时间、重金属离子起始浓度和吸附剂用量对吸附过程的影响。等温吸附过程可以用Langmuir方程来描述。在实验设定条件下,棘孢曲霉对Pb~(2+)和Cd~(2+)最大吸附量分别为71.2 mg/g和59.8 mg/g;动力学实验数据很好的符合二级动力学方程,吸附达到平衡的时间为3 h;热力学实验数据显示该吸附过程为自发的、吸热的过程。     

棘孢曲霉（Aspergillus aculeatus）对Pb2＋和Cd2＋的吸附特征

为了研究棘孢曲霉（Aspergillus aculeatus）对溶液中Pb^2＋和Cd^2＋吸附过程的特征,分别从动力学、热力学和吸附等温线三方面进行了实验,同时还研究了pH、温度、时间、重金属离子起始浓度和吸附剂用量对吸附过程的影响。等温吸附过程可以用Langmuir方程来描述。在实验设定条件下,棘孢曲霉对Pb^2＋和Cd^2＋最大吸附量分别为71.2 mg/g和59.8 mg/g;动力学实验数据很好的符合二级     

棘孢曲霉（Aspergillus aculeatus）对Pb^2＋和Cd^2＋的吸附特征

为了研究棘孢曲霉（Aspergillus aculeatus）对溶液中Pb^2＋和Cd^2＋吸附过程的特征,分别从动力学、热力学和吸附等温线三方面进行了实验,同时还研究了pH、温度、时间、重金属离子起始浓度和吸附剂用量对吸附过程的影响。等温吸附过程可以用Langmuir方程来描述。在实验设定条件下,棘孢曲霉对Pb^2＋和Cd^2＋最大吸附量分别为71．2mg／g和59．8mg／g;动力学实验数据很好的符合二级动力学方程,吸附达到平衡的时间为3h;热力学实验数据显示该吸附过程为自发的、吸热的过程。     

Characterization and lead(II), cadmium(II), nickel(II) biosorption of dried marine brown macro algae Cystoseira barbata

Purpose

The objectives of this research are to identify the functional groups and determine corresponding pK _a values of the acidic sites on dried brown algae Cystoseira barbata using FTIR and potentiometric titrations, and to investigate the biosorption ability of biomass towards divalent nickel, cadmium, and lead ions. Adsorption was studied as a function of solution pH and contact time, and experimental data were evaluated by the Langmuir isotherm model.

Methods

CaCl₂ pretreatment was applied to the sorbent for enhancing the metal uptake capacity. The effect of solution pH on biosorption equilibrium was investigated in the pH range of 1.5?C5.0. Individual as well as competitive adsorption capacity of the sorbent were studied for metal cations and mixtures.

Results

The retention of the tested metal ions was mostly influenced from pH in the range of 1.5?C2.5, then stayed almost constant up to 5.0, while Ni(II) uptake showed the highest variation with pH. Potentiometric titrations were performed to find the number of strong and weak acidic groups and their acidity constants. The density of strong and weak acidic functional groups in the biomass were found to be 0.9 and 2.26?mmol/g, respectively. The FTIR spectra of the sorbent samples indicated various functionalities on the biomass surface including carboxyl, hydroxyl, and amino and sulphonate groups which are responsible for the binding of metal ions.

Conclusions

The capacity of the biomass for single metal ions (around 1?mmol/g) was increased to 1.3?mmol/g in competitive adsorption, Pb(II) showing the highest Langmuir intensity constant. Considering its extremely high abundance and low cost, C. barbata may be potentially important in metal ion removal from contaminated water and industrial effluents.     

Biosorption of lead(II) in aqueous solution by spent mushroom Tricholoma lobayense

The biosorption of lead(II) ions in both simulated and real wastewater by spent mushroom Tricholoma lobayense, was studied in this work. The results show a biomass with a high potential for removing lead ions from wastewater. The optimum pH for the adsorption is 4, and the adsorption process is fast. The best sorbent mass of the biomaterial is 5 g/L with an initial lead(II) concentration of 1 mmol/L. The process follows the Langmuir isotherm model, and the biosorption capacity of lead ions reaches to 210 mg/g, which is higher than many biosorbents previously studied. The mechanism of biosorption may be mainly attributed to ion exchange. The FT-IR study identifies the functional groups responsible for this process. A scanning electron microscope showed a significant change of the sorbent surface after the biosorption process. The energy dispersive elemental analysis also confirmed the adsorption of lead(II) ions.     

Biosorption of Pb(II) by biomass of KC-2: kinetic, equilibrium and characteristic studies

Performance and characteristics of biosorption of Pb(II) had been studied in a batch system using the fungal strain biomass, KC-2. The biosorption performance was investigated by analysing the effects of such factors as the initial pH, initial Pb(II) concentration, and contact time at 303 K. The maximum Pb(II) adsorption was obtained at pH 5.0. The experimental data were described by the pseudo first-order, pseudo second-order and intraparticle diffusion kinetic models, and were closely followed the pseudo second-order kinetic model. The equilibrium experimental data were well fitted to Langmuir model and the maximum biosorption capacity was 84.03 mg g(-1). The adsorption mechanism was examined by FTIR, SEM and EDAX analysis. Results indicated that carboxylic, hydroxyl and amine groups were involved in the biosorption and ion exchange mechanism existed.     

Simultaneous heavy metal removal mechanism by dead macrophytes

The use of dead, dried aquatic plants, for water removal of metals derived from industrial activities as a simple biosorbent material has been increasing in the last years. The mechanism of simultaneous metal removal (Cd2+, Ni2+, Cu2+, Zn2+ and Pb2+) by 3 macrophytes biomass (Spirodela intermedia, Lemna minor and Pistia stratiotes) was investigated. L. minor biomass presented the highest mean removal percentage and P. stratiotes the lowest for all metals tested. Pb2+ and Cd2+ were more efficiently removed by the three of them. The simultaneous metal sorption data were analysed according to Langmuir and Freundlich isotherms. Data fitted the Langmuir model only for Ni and Cd, but Freundlich isotherm for all metals tested, as it was expected. The K(F) values showed that Pb was the metal more efficiently removed from water solution. The adsorption process for the three species studied followed first order kinetics. The mechanism involved in biosorption resulted ion exchange between monovalent metals as counter ions present in the macrophytes biomass and heavy metal ions and protons taken up from water. No significant differences were observed in the metal exchange amounts while using multi-metal or individual metal solutions.     

Lead biosorption and desorption by intact and pretreated spirulina maxima biomass

In order to search for locally available and untried biomaterials in China with high removal capacity of heavy metals from wastewater, the feasibility of Spirulina maxima as biosorbent for lead removal and recovery from aqueous solution was investigated. The lead biosorption was studied by using intact biomass and pretreated biomass of S. maxima. The effects of operational conditions (e.g. pH, contact time, biomass concentration etc.) on lead biosorption were investigated. The biosorption was solution pH dependent and the maximum adsorption was obtained at a solution pH of about 5.5. The adsorption equilibrium was reached in 60 min. The biosorption followed the Freundlich isotherm model. The maximum removal ratios of lead were about 84% in intact biomass and 92% in pretreated biomass. The lead adsorbed could be desorbed effectively by 0.1 M nitric acid, EDTA and hydrochloric acid. The results in this study indicated that pretreated biomass of S. maxima was a promising candidate for removing lead from wastewater.     

Removal of metal ions from the complexed solutions in fixed bed using a strong-acid ion exchange resin

Fixed bed removal of equimolar metal ions (Co²⁺, Ni²⁺, Mn²⁺, Sr²⁺) from aqueous solutions using a strong-acid resin was examined. The solution contained a water-soluble complexing agent including ethylenediaminetetraacetic acid, nitrilotriacetic acid, and citric acid. Experiments were performed under different solution pH and molar concentration ratios of complexing agent to the total metals. It was shown from batch studies that the equilibrium exchange of metals and the resin mainly depended on solution pH, and partly on the type of complexing agent used. A mass transfer model was proposed to describe the breakthrough curves of the resin bed, which contained two parameters (τ and k) estimated from the observed breakthrough data. The calculated breakthrough curves agreed well with the measured ones (standard deviation <6%). In fixed bed tests at low pH (=2), the type of complexing agent had little effect on the breakthrough data. For a given complexing agent, the metal with a larger overall formation constant (K_f) showed a smaller exchange capacity. For a given metal ion, the complexing agent with a larger K_f also revealed a smaller exchange capacity.     

Biosorption of Cr3+, Cd2+ and Cu2+ ions by blue-green algae Spirulina sp.: kinetics, equilibrium and the mechanism of the process

The process of biosorption of heavy metal ions (Cr3+, Cd2+, Cu2+) by blue-green algae Spirulina sp. is discussed in this paper. Spirulina sp. was found to be a very efficient biosorbent. The aim of the present study was to investigate quantitatively the potential binding sites present at the surface of Spirulina sp., using both potentiometric titrations and adsorption isotherms. The kinetic experiments showed that the process equilibrium was reached quickly, in less than 5-10 min. It was found that the equilibrium dependence between biosorption capacity and bulk metal ion concentration could be described with Langmuir equation. This suggests that the mechanism of biosorption is rather chemisorption than physical adsorption and was further confirmed by the low surface area associated with physical adsorption and by the presence of cations that appeared in the solution after biosorption. The maximum contribution of physical adsorption in the overall biosorption process was evaluated as 3.7%. It was proposed that functional groups on the cell surface contributed to the binding of metal ions by a biosorbent via equilibrium reaction. Three functional groups capable of cation exchange were identified on the cell surface. The biomass was described as weakly acidic ion exchanger. Since deprotonation of each functional group depends on pH, the process of biosorption is strongly pH-dependent. This was confirmed in the biosorption experiments carried out at different pH. The contribution of functional groups in the biosorption process was confirmed by chemical modification of the groups. Chemically blocked groups did not show neither biosorption nor ion-exchange capabilities. It has been shown that growth conditions can affect the metal adsorption properties of microalgae. The paper also discusses desorption characteristics of the biosorbent. The criteria for desorption were high elution efficiency and preservation of biosorptive properties. Desorbent that possessed these characteristics was nitric acid.     

一株产絮酵母菌废菌体对Cd2+的吸附特性

将一株产絮酵母菌(编号B-02号)发酵后的废菌体制成生物吸附剂,研究该生物吸附剂对废水中Cd2+的生物吸附特性。结果表明:(1)pH值对Cd2+会产生较大的影响,偏酸性(pH=4～6)条件利于吸附;该吸附剂对Cd2+吸附速率较快,8～10 min就可达到吸附平衡;(2)吸附剂的吸附动力学符合二级动力学模型,吸附Cd2+的实验数据对Langmuir等温式的拟合情况良好,吸附剂吸附Cd2+的最大吸附量为70.752 mg/g。用0.5 mol/L HNO3对吸附Cd2+的酵母菌进行解吸,解吸率可达89.7%。     

非固定化和固定化啤酒酵母对Cd^2＋和Cu^2＋的吸附特性研究

对比了不同吸附剂对重金属的吸附效果,同时研究了啤酒酵母的固定化方法、菌体用量对吸附效果的影响、非同定化和固定化啤酒酵母吸附热力学特性。研究结果表明,非固定化死啤酒酵母对Cd^2＋的单位菌体吸附量是常用吸附剂活性炭的3倍;由1：3的海藻酸钠与碱处理啤酒酵母（w／w）制得的固定化颗粒吸附效果最好;菌体用量的增加会降低单位菌体对重金属的吸附量;啤酒酵母对重金属的吸附位点有限,Cd^2＋的实际最大吸附量为13．95mg／g,Cu^2＋为7．67μg／g。非固定化和固定化啤酒酵母对Cu^2＋和Cd^2＋的等温吸附过程均可用Linear方程、Langmuir方程和Freundlich方程来进行拟合,但非同定化啤酒酵母以Langmuir方程最优,其拟合计算的最大吸附量qmzxCd和qmxxCu分别为13．96mg／g和8．01mg／g;固定化啤酒酵母以Freundlich方程最优,实际最大吸附量Cd为75．41mg／g,Cu为66．58mg／g。     

Kinetic studies of adsorption of thiocyanate onto ZnCl2 activated carbon from coir pith, an agricultural solid waste

The adsorption of thiocyanate onto ZnCl₂ activated carbon developed from coir pith was investigated to assess the possible use of this adsorbent. The influence of various parameters such as agitation time, thiocyanate concentration, adsorbent dose, pH and temperature has been studied. Adsorption followed second-order rate kinetics. Two theoretical adsorption isotherms, namely, Langmuir and Freundlich were used to describe the experimental results. The Langmuir adsorption capacity (Q₀) was found to be 16.2 mg g⁻¹ of the adsorbent. The per cent adsorption was maximum in the pH range 3.0–7.0. pH effect and desorption studies showed that ion exchange and chemisorption mechanism are involved in the adsorption process. Thermodynamic parameters such as ΔG⁰, ΔH⁰ and ΔS⁰ for the adsorption were evaluated. The negative values of ΔH⁰ confirm the exothermic nature of adsorption. Effects of foreign ions on the adsorption of thiocyanate have been investigated. Removal of thiocyanate from ground water was also tested.     

Competitive biosorption of lead, cadmium, copper, and arsenic ions using algae

The present study aims to evaluate the competitive biosorption of lead, cadmium, copper, and arsenic ions by using native algae. A series of experiments were carried out in a batch reactor to obtain equilibrium data for adsorption of single, binary, ternary, and quaternary metal solutions. The biosorption of these metals is based on ion exchange mechanism accompanied by the release of light metals such as calcium, magnesium, and sodium. Experimental parameters such as pH, initial metal concentrations, and temperature were studied. The optimum pH found for removal were 5 for Cd²⁺ and As³⁺ and 3 and 4 for Pb²⁺ and Cu²⁺, respectively. Fourier transformation infrared spectroscopy analysis was used to find the effects of functional groups of algae in biosorption process. The results showed that Pb²⁺ made a greater change in the functional groups of algal biomass due to high affinity to this metal. An ion exchange model was found suitable for describing the biosorption process. The affinity constants sequence calculated for single system was K _Pb > K _Cu > K _Cd > K _As; these values reduced in binary, ternary, and quaternary systems. In addition, the experimental data showed that the biosorption of the four metals fitted well the pseudo-second-order kinetics model.     

Biosorption characteristics of Bacillus gibsonii S-2 waste biomass for removal of lead (II) from aqueous solution

Lead (II) has been as one of the most toxic heavy metals because it is associated with many health hazards. Therefore, people are increasingly interested in discovering new methods for effectively and economically scavenging lead (II) from the aquatic system. Recent studies demonstrate biosorption is a promising technology for the treatment of pollutant streams. To apply these techniques, suitable adsorbents with high efficiency and low cost are demanded. The waste biomass of Bacillus gibsonii S-2 biosorbent was used as low-cost biosorbent to remove metallic cations lead (II) from aqueous solution. To optimize the maximum removal efficiency, the effect of pH and temperature on the adsorption process was studied. The isotherm models, kinetic models and thermodynamic parameters were analysed to describe the adsorptive behaviour of B. gibsonii S-2 biosorbent. The mechanisms of lead (II) biosorption were also analysed by FTIR and EDX. The results showed that the optimum pH values for the biosorption at three different temperatures, i.e. 20, 30 and 40 °C, were determined as 4. The equilibrium data were well fitted to Langmuir model, with the maximum lead (II) uptake capacities of 333.3 mg?g^?1. The kinetics for lead (II) biosorption followed the pseudo-second-order kinetic equation. The thermodynamic data showed that the biosorption process were endothermic (?G?<?0), spontaneous (?H?>?0) and irreversible (?S?>?0). The mechanism of lead (II) biosorption by the waste biomass of B. gibsonii S-2 biosorbent could be a combination of ion exchange and complexation with the functional groups present on the biosorbent surface. The application of the waste biomass of B. gibsonii S-2 for lead (II) adsorption, characterized with higher lead (II) sorption capacity and lower cost, may find potential application in industrial wastewater treatment.     

浮游球衣菌对Pb2+、Cu2+、Zn2+、Cd2+的吸附性能研究

研究了浮游球衣菌（Sphaerotilus natans）在不同吸附条件下对溶液中Pb^2＋、Cu^2＋、Zn^2＋、Cd^2＋的吸附规律。结果表明,Sphaerotilus natans对这4种重金属离子均有一定的吸附作用,并在20min内达到吸附平衡,pH对吸附过程影响较大,pH为5.5时Sphaerotilus natans对这4种金属离子的吸附效果最好,Sphaerotilus natans对它们的吸附选择性为Pb^2＋〉Cu^2＋〉Zn^2＋〉Cd^2＋,Pb^2＋、Cu^2＋能部分置换出已被菌体吸附的Zn^2＋、Cd^2＋。HCI和EDTA溶液可有效地将金属离子从菌体上解吸下来,解吸后的菌体可重复使用。