Fe2O3/TiO2负载膨胀珍珠岩光催化降解罗丹明B

为获得高效催化活性的光催化材料,研究不同煅烧氛围对材料在可见光下催化性能的影响,以膨胀珍珠岩（EP）为载体,采用溶胶-凝胶法,在不同煅烧氛围（O₂和/或NH₃）下制备Fe₂O₃/TiO₂负载EP的光催化复合材料〔Fe₂O₃-TEP（O₂）、Fe₂O₃-TEP（NH₃）、Fe₂O₃-TEP（O₂,NH₃）、Fe₂O₃-TEP（NH₃,O₂）〕,采用EDS（X-射线色散能谱）、BET（比表面积及孔径分析）、XRD（X射线衍射）、SEM（扫描电子显微镜）、XPS（X射线光电子能谱）等对复合材料进行表征,并研究了其在可见光下对罗丹明B的光催化降解效果.结果表明:①复合材料成功负载了Ti、Fe元素,负载的TiO₂以锐钛矿型存在,Fe₂O₃的掺杂增强了TiO₂对可见光的响应能力;②不同的煅烧氛围明显影响复合材料的晶粒尺寸、比表面积和光催化性能,其中,Fe₂O₃-TEP（O₂,NH₃）的光催化性能最好,4 h后罗丹明B降解率达到87.59%,Fe₂O₃-TEP（NH₃,O₂）、Fe₂O₃-TEP（O₂）和Fe₂O₃-TEP（NH₃）4 h后对罗丹明B的降解率则分别为65.02%、62.48%和47.48%;③在试验条件下,复合材料的光催化反应符合一阶反应动力学方程,Fe₂O₃-TEP（O₂,NH₃）、Fe₂O₃-TEP（NH₃,O₂）、Fe₂O₃-TEP（O₂）和Fe₂O₃-TEP（NH₃）相应的降解速率常数分别为0.008 3、0.004 3、0.004 3和0.002 7 min-1.研究显示,通过溶胶-凝胶法所制备的复合材料（Fe₂O₃-TEP）经煅烧后所得矿相均一;Fe₂O₃掺杂TiO₂可形成Ti—O—Fe键,减小TiO₂固有的禁带宽度;复合材料光催化性能也受到煅烧氛围的影响,先O₂后NH₃煅烧条件下所得材料的光催化性能最佳.      

Bi2O3-TiO2复合光催化剂协同处理铬-邻苯二甲酸酯复合污染

以硝酸铋和钛酸丁酯为前驱体,采用水热法制备了Bi_2O_3-TiO_2复合半导体材料,并利用X射线衍射(XRD)、紫外-可见吸收光谱(UVVis)、能谱分析(EDS)、X射线光电子能谱(XPS)等手段对复合材料的结构进行了表征.同时,考察了Bi_2O_3-TiO_2复合材料对重金属Cr(Ⅵ)和难降解邻苯二甲酸二丁酯(DBP)复合污染的处理性能,并探讨了复合催化剂协同处理复合污染的作用机制.结果表明:该复合催化剂在可见光下能同时降低重金属Cr(Ⅵ)和有机物DBP的浓度,抑制电子和空穴复合,表现出比对单一Cr(Ⅵ)及DBP污染物更高的处理效率.当Bi_2O_3含量为4%时,复合催化剂表现出最佳的光催化活性.     

Ni2P/Bi2MoO6复合材料的制备及可见光催化活性

分别制备了花状Bi₂MoO₆和片状Ni₂P,采用研磨、水热及超声的方式将两种材料复合,考察了负载方式、负载率和溶液pH值对其可见光下降解亚甲基蓝（MB）的影响;利用XRD、XPS、FTIR、SEM、PL和UV-Vis等测试手段表征了样品的微观结构、形貌和光学性质;研究表明Ni₂P作为助催化剂,可加速电子空穴对分离,显著提高Bi₂MoO₆的光催化活性,其中当Ni₂P负载率为4%时,TOC去除率为64.28%,降解速率为纯Bi₂MoO₆的2倍,且将Ni₂P/Bi₂MoO₆复合催化剂循环利用3次后,同实验条件下降解率为94%,证明复合催化剂稳定性好.     

TiO2-石墨烯（Gn）复合材料光催化降解O3研究

通过改性Hummer法及溶胶凝胶法,制备出TiO2-石墨烯光催化复合材料.经吸附-光催化活性实验选出光催化活性最高的含C量为1.5%(质量分数)的TiO2-石墨烯复合材料,并在自行设计的模拟大型客机环境的气相光催化反应器中,进行O3光催化降解实验研究.结果表明,TiO2-石墨烯复合光催化材料在较短时间内对O3有较高的降解效率,且其光催化活性显著优于纯TiO2材料.初始O3浓度为(0.150～0.200)×10-6时,复合光催化剂受紫外光激发60 min的光催化降解率为66.12%,初始O3浓度为(0.950～1.000)×10-6时,其光催化降解率约为77%,较低浓度时((0.100～0.150)×10-6),O3去除率也能达到45.45%.此外,通过探讨光催化材料的重复使用性能,表明复合光催化剂重复使用4次以内,其对O3的光催化降解率保持基本稳定.     

BiOCl/TiO2的氯化改性及其新式光生自由基催化反应

采用溶胶凝胶法制备了BiOCl/TiO₂复合催化剂,透射电镜（TEM）照片显示,两种半导体分布均匀、相互连接,形成的异质结可以为电子传导提供有效通道.经过氯化处理的复合材料具备更强的光催化能力,在紫外光条件下对苯的降解率达到90%,是原BiOCl/TiO₂的2倍、纯TiO₂的10倍.本文利用X射线光电子能谱、红外光谱和电子顺磁共振,对表面氯化的机理进行研究.结果表明,氯元素以Ti—Cl的方式吸附在催化剂表面,在光照条件下光生空穴夺取一个电子,使其生成氯自由基,进而配合超氧、羟基,构成一种新型的三自由基光催化体系,使催化降解能力大幅提升.最后,利用实验方法得到了光生氯自由基的直接证据,并构建了该体系的光催化反应机理.     

C3N4/BiOBr复合可见光催化剂的性能及其作用机制

利用水热合成法制备了C_3N_4/BiOBr复合可见光催化剂,通过XRD、FT-IR、SEM、DRS、PL等手段对催化剂的物相组成和光化学性能进行了系统表征,利用对罗丹明B(RhB)的降解实验评价了催化剂在可见光照下的光催化降解活性和稳定性并通过ESR分析和自由基捕获实验探究了RhB的光催化降解机制.结果表明,水热合成法可成功制备结晶性能良好的C_3N_4/BiOBr复合可见光催化剂;C_3N_4的复合降低了BiOBr光催化剂的电子-空穴的复合,提高了光催化降解活性,其中15%C_3N_4/BiOBr的活性最佳,可见光照18 min后RhB的脱色率达100%,较纯BiOBr提高了1.5倍,且重复使用5次后仍具有较高的光催化降解活性;复合催化剂光催化降解RhB过程中参与降解的主要活性物种为空穴(h~+)和超氧自由基(·O_2~-),其中h~+影响更为显著.     

Enhanced photocatalytic activity of fish scale loaded TiO2 composites under solar light irradiation

Fish scale (FS) loaded TiO₂ composites were investigated as photocatalysts in degradation of Methyl Orange under solar light irradiation. Composites were prepared through sol-gel method by varying mass ratio of TiO₂/FS at 90:10, 70:30 and 50:50, respectively. The catalysts prepared in this study were characterized by using XRD, SEM, FT-IR and nitrogen sorption. The effects of solar irradiation, mass ratio of TiO₂/FS composites, irradiation time and catalyst loadings were studied. Synergistic effect was found in TiO₂/FS of 90:10 composite which performed higher photocatalytic degradation than synthesized TiO₂ under solar light irradiation. However, further increasing fish scale content in the composites reduced the photocatalytic activity drastically. Under solar light irradiation, all the catalysts in this study exhibited photocatalytic activity, except TiO₂/FS of 50:50 composite that only acted as a weak biosorbent without performing any photocatalytic property. Photocatalytic degradation increased with increasing catalyst loading and irradiation time but decreased with increased of initial dye concentration.     

上转换发光剂掺杂纳米TiO2的制备及可见光降解乙基紫的研究

合成了一种新型含有稀土金属Er的上转换发光剂40CdF₂·60BaF₂·1.6Er₂O₃,此上转换发光剂在488 nm可见光的激发下,产生了5个波长均小于387 nm的上转换紫外光发射峰.采用超声波分散的方法制备出了上转换发光剂掺杂的纳米TiO₂可见光光催化剂.利用X-射线衍射(XRD)及透射电镜(TEM)对催化剂进行了表征.以乙基紫染料为研究对象,研究了在(三基色灯下发出的)可见光的照射下该可见光光催化剂的催化降解性能,并与未掺杂的纳米TiO₂粉末的催化性能进行了对比.结果表明,作为掺杂成分的上转换发光剂可有效地将可见光转化为紫外光并被纳米TiO₂粉末吸收利用,在可见光照射12.0 h后乙基紫降解率达到了99.68%,大大高于未掺杂纳米TiO2时的降解率.     

Effect of TiO2 calcination temperature on the photocatalytic oxidation of gaseous NH3

Carbon-modified titanium dioxide(TiO2) was prepared by a sol-gel method using tetrabutyl titanate as precursor, with calcination at various temperatures, and tested for the photocatalytic oxidation(PCO) of gaseous NH3 under visible and UV light. The test results showed that no samples had visible light activity, while the TiO2 calcined at 400℃ had the best UV light activity among the series of catalysts, and was even much better than the commercial catalyst P25. The catalysts were then characterized by X-ray diffractometry, Brunauer-Emmett-Teller adsorption analysis, Raman spectroscopy, thermogravimetry/differential scanning calorimetry coupled with mass spectrometry, ultraviolet-visible diffuse reflectance spectra, photoluminescence spectroscopy and in situ diffuse reflectance infrared Fourier transform spectroscopy. It was shown that the carbon species residuals on the catalyst surfaces induced the visible light adsorption of the samples calcined in the low temperature range( 300℃). However, the surface acid sites played a determining role in the PCO of NH3 under visible and UV light over the series of catalysts. Although the samples calcined at low temperatures had very high SSA, good crystallinity, strong visible light absorption and also low PL emission intensity, they showed very low PCO activity due to their very low number of acid sites for NH3 adsorption and activation. The TiO2 sample calcined at 400℃ contained the highest number of acid sites among the series of catalysts, therefore showing the highest performance for the PCO of NH3 under UV light.     

Visible light responsive N-F-codoped TiO2 photocatalysts for the degradation of 4-chlorophenol

Visible light responsive N-F-codoped TiO₂ photocatalysts exhibit a higher catalytic activity than N-doped TiO₂ for the degradation of 4-chlorophenol due to the synergistic effect of nonmetal elements.     

Synthesis of novel CeO2-BiVO4/FAC composites with enhanced visible-light photocatalytic properties

To utilize visible light more effectively in photocatalytic reactions, a fly ash cenosphere （FAC）-supported CeO2-BiV04 （CeO2-BiVO4/FAC） composite photocatalyst was prepared by modified metalorganic decomposition and impregnation methods. The physical and photophysical properties of the composite have been characterized by X-ray diffraction （XRD）, scanning electron microscope （SEM） and energy dispersive X-ray spectroscopy （EDX）, X-ray photoelectron spectroscopy （XPS）, and UV-Visible diffuse reflectance spectra. The XRD patterns exhibited characteristic diffraction peaks of both BiVO4 and Ce02 crystalline phases. The XPS results showed that Ce was present as both Ce4＋ and Ce3＋ oxidation states in Ce02 and dispersed on the surface of BiV04 to constitute a p-n heterojunction composite. The absorption threshold of the CeO2-BiVO4/FAC composite shifted to a longer wavelength in the UV-Vis absorption spectrum compared to the pure Ce02 and pure BiV04. The composites exhibited enhanced photocatalytic activity for Methylene Blue （MB） degradation under visible light irradiation. It was found that the 7.5 wt.% CeO2-BiVO4/FAC composite showed the highest photocatalytic activity for MB dye wastewater treatment.     

FeTiO3/TiO2纳米异质结的制备和可见光催化性能

采用水热法和溶胶凝胶法制备了新型FeTiO3/TiO2纳米异质结复合材料,并明确了最优的掺杂比例(0.5%).随后利用X射线衍射能谱(XRD)、紫外-可见漫反射光谱(UV-Vis DRS)、扫描电镜(SEM)和透射电镜(TEM)等手段对该复合材料进行表征,证实了其结晶度、吸光度随掺杂量的规律性变化.电镜照片显示,该复合材料具有蓬松多孔的微观结构,且晶格条纹清晰、分散度高,有利于光电子的传导.对苯的降解实验表明,相比于纯TiO2,该催化剂的气相可见光催化能力大幅提高,降解率提升了3倍,达到40%,而CO2生成量提升了5倍,超过300 ppm.同时,电化学测试和电子顺磁共振谱(ESR)等均证实,FeTiO3的窄能带能够提高TiO2的光响应,实现可见光激发;而二者的能带相互匹配,有助于转移光生载流子,实现电子-空穴的高效分离,进而其光生电子和自由基生成能力大幅增强,因此,表现出了较强、较稳定的光催化活性.     

Bi掺杂In2TiO5纳米带的制备及其光催化性能

以Bi(NO_3)_3、Ti(OC_4H_9)_4、In(NO_3)_3和聚乙烯吡咯烷酮(PVP-K30)为原料,采用静电纺丝法和沉淀法相结合,成功制备了Bi掺杂In_2TiO_5(Bi-In_2TiO_5)纳米带.利用X射线衍射(XRD)、扫描电子显微镜(SEM)、X射线能量色散谱(EDS)、紫外-可见漫反射光谱(UV-vis DRS)和氮气吸附-脱附等温线(BET)等技术对样品进行表征.结果表明,Bi的掺杂未引入新的杂相,样品均为正交晶系结构,掺杂前后样品的形貌未发生明显变化.适量的Bi掺杂,在In2Ti O5晶格中形成杂质能级,降低了In_2TiO_5的带隙能.当掺杂量为2%时,制备的Bi-In_2TiO_5纳米带的光催化活性最高.在氙灯(150 W)辐照下,150 min,对罗丹明B的降解率达95.8%,且该催化剂对氟喹诺酮类抗生素左氧氟沙星(LEV)也表现出优良的光催化降解性能.     

WC/TiO2纳米复合界面光催化剂制备及其光催化降解酚类污染物研究

设计并制备了新型WC/TiO2纳米复合界面光催化剂应用于酚类污染物的光催化降解反应中.采用X射线衍射(XRD)和扫描电子显微镜(SEM)技术分析了WC/TiO2纳米复合界面光催化剂的晶型和表面形貌.结果显示锐钛矿型TiO2纳米颗粒均匀地分散在WC纳米球表面并很好地构筑了WC/TiO2界面.研究了不同WC负载比例的WC/TiO2光催化剂在模拟太阳光照射下降解苯酚的光催化性能.结果表明:WC/TiO2复合界面的形成可以有效地提高TiO2光催化降解性能;其中,3%WC/TiO2(质量分数)光催化降解苯酚的活性最高.利用紫外-可见光谱(UV-Vis)和高效液相色谱-质谱联用技术(HPLC-MS)分析了WC/TiO2纳米复合界面光催化剂降解苯酚的中间产物,提出了苯酚在WC/TiO2界面上可能的降解机理.     

TiO2-Fe3+可见光催化H2O2降解阿特拉津的协同效应

以内分泌干扰物阿特拉津为模型污染物,研究了TiO2-Fe3+可见光催化H2O2降解阿特拉津的协同效应.结果表明,在H2O2存在条件下,金红石TiO2经可见光激发可持续稳定地产生.OH自由基,在Fe3+协同作用下,.OH自由基生成量急剧增加;TiO2能可见光催化H2O2降解阿特拉津,金红石TiO2显示出较锐钛矿TiO2及混晶TiO2(TiO2P25)更高的催化活性,反应60 min,阿特拉津的降解率可达40%;以Fe3+协同TiO2可见光催化H2O2降解阿特拉津时,反应效率显著加快,反应5 min即对阿特拉津的降解率达到100%,而金红石TiO2显示出更为明显的协同效应.     

Synergistic effect of N- and F-codoping on the structure and photocatalytic performance of TiO2

Three types of TiO₂ nanostructures were synthesized via a facile hydrolysis method at 195 °C. Effects of the preparation method and doping with N and F on the crystal structure and photocatalytic performance of TiO₂ were investigated. The nanomaterials were characterized by X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, Brunauer–Emmett–Teller porosimetry, ultraviolet–visible diffuse reflectance spectroscopy and fluorescent emission spectra. Their photo-catalytic activity was examined by the photodegradation of methylene blue in aqueous solution under both ultra-violet and visible light irradiation. The results show that nitrogen and fluorine co-doped anatase TiO₂ had the characteristics of a smaller crystalline size, broader light absorption spectrum and lower charge recombination than pure TiO₂. Most importantly, more efficient photocatalytic activity under both ultra-violet and visible light was observed. The obtained N–F-TiO₂ nanomaterial shows considerable potential for water treatment under sunlight irradiation.     

Tricrystalline TiO2 with enhanced photocatalytic activity and durability for removing volatile organic compounds from indoor air

It is important to develop efficient and economic techniques for removing volatile organic compounds(VOCs) in indoor air. Heterogeneous Ti O_2-based semiconductors are a promising technology for achieving this goal. Anatase/brookite/rutile tricrystalline Ti O_2 with mesoporous structure was synthesized by a low-temperature hydrothermal route in the presence of HNO_3.The obtained samples were characterized by X-ray diffraction and N_2 adsorption–desorption isotherm. The photocatalytic activity was evaluated by photocatalytic decomposition of toluene in air under UV light illumination. The results show that tricrystalline Ti O_2 exhibited higher photocatalytic activity and durability toward gaseous toluene than bicrystalline Ti O_2,due to the synergistic effects of high surface area, uniform mesoporous structure and junctions among mixed phases. The tricrystalline Ti O_2 prepared at R HNO_3= 0.8, containing80.7% anatase, 15.6% brookite and 3.7% rutile, exhibited the highest photocatalytic activity,about 3.85-fold higher than that of P25. The high activity did not significantly degrade even after five reuse cycles. In conclusion, it is expected that our study regarding gas-phase degradation of toluene over tricrystalline Ti O_2 will enrich the chemistry of the Ti O_2-based materials as photocatalysts for environmental remediation and stimulate further research interest on this intriguing topic.     

TiO2-PW9复合催化剂光催化降解游离氰

采用水热法制备了二氧化钛(TiO_2)与三缺位磷钨酸钠(Na_8H[β-A-PW_9O_(34)]·24H_2O)共价结合形成的TiO_2-PW_9复合催化剂,并对其光催化降解游离氰(CN~-)的效果进行了研究.NMR和XPS等表征结果证明,Na_8H[β-A-PW_9O_(34)]·24H_2O(简写为Na-PW_9)已成功负载于TiO_2上.光电化学表征结果表明,Na-PW_9的引入可有效提高TiO_2的界面电荷转移.光催化实验结果表明,与单独TiO_2相比,TiO_2-PW_9的光催化活性有明显提高.同时,探究了初始CN~-浓度和催化剂投加量对CN~-去除的影响.结果表明,当初始CN~-浓度为0.3 mmol·L~(-1)、催化剂投加量为1 g·L~(-1)时,复合催化剂的光催化活性最佳,反应150 min后,CN~-的去除率达到81%.CN~-的氧化产物分析结果表明,氰酸根(CNO~-)是CN~-氧化的唯一产物.自由基淬灭实验和电子自旋共振(ESR)波谱分析结果表明,~1O_2是反应体系中的主要活性氧物种.本实验可为多功能催化材料的开发及其在含氰废水污染控制领域的应用提供参考.     

Effect of Ce doping of TiO2 support on NH3-SCR activity over V2O5-WO3/CeO2-TiO2 catalyst

CeO2–TiO2composite supports with different Ce/Ti molar ratios were prepared by a homogeneous precipitation method, and V2O5–WO3/CeO2–TiO2catalysts for the selective catalytic reduction（SCR） of NOx with NH3 were prepared by an incipient-wetness impregnation method. These catalysts were characterized by means of BET, XRD, UV–Vis,Raman and XPS techniques. The results showed that the catalytic activity of V2O5–WO3/TiO2 was greatly enhanced by Ce doping（molar ratio of Ce/Ti = 1/10） in the TiO2 support.The catalysts that were predominantly anatase TiO2 showed better catalytic performance than the catalysts that were predominantly fluorite CeO2. The Ce additive could enhance the surface adsorbed oxygen and accelerate the SCR reaction. The effects of O2 concentration, ratio of NH3/NO, space velocity and SO2 on the catalytic activity were also investigated. The presence of oxygen played an important role in NO reduction. The optimal ratio of NH3/NO was 1/1 and the catalyst had good resistance to SO2 poisoning.     

UV/TiO2/H2O2体系对制药废水二级出水的处理特性研究

以某制药企业的二级出水为研究对象,对比了UV/TiO₂、UV/H₂O₂、UV/TiO₂/H₂O₂ 3种高级氧化工艺的处理效果,利用自主设计的一体化光催化装置进行了连续动态试验,并通过凝胶渗透色谱（GPC）、傅里叶变换红外光谱（FT-IR）、三维荧光光谱（EEM）、斑马鱼急性毒性试验等方法研究了处理前后有机物特性和生物毒性的变化.结果表明,与UV/TiO₂和UV/H₂O₂体系相比,UV/TiO₂/H₂O₂光芬顿体系对有机物的去除效果更好,当TiO₂投加量为1 g·L^-1,H₂O₂投加量为100 mg·L^-1时,处理效果达到最佳.一体化光催化装置能够利用UV/TiO₂/H₂O₂光芬顿技术快速高效地降解二级出水中的有机污染物,反应30 min时COD去除率达到50%以上.经UV/TiO₂/H₂O₂深度处理后,废水中的大分子有机物分解转换为小分子,有机物中的不饱和结构明显减少,腐殖质等溶解性有机物基本降解完全.毒性试验结果表明,该二级出水的生物毒性经深度处理后显著降低,对斑马鱼胚胎不存在致畸致死效应.