Fenton氧化-前置反硝化缺氧好氧池(A/O)处理荧光增白剂废水中试研究

采用Fenton氧化-前置反硝化缺氧好氧池(A/O)对荧光增白剂废水IC出水进行中试实验研究。实验表明,在Fe2+投加量为0.003 mol/L,进水pH值为3,[H2O2]/[Fe2+]为4∶1,反应时间为2 h的条件下,Fenton氧化法对COD的去除率可以达到46%以上,出水BOD5/COD的值由0.26提高到0.58。氧化后废水进入前置反硝化生物脱氮系统进行生化处理,该系统采用间歇式进水,水力停留时间为2 d,实验结果表明,A/O系统对COD、氨氮和总氮的去除率分别达41%、90%以上和86%。该组合工艺对COD的总去除率可达到67%,出水氨氮在20 mg/L以下,总氮在37 mg/L以下。     

Fenton氧化-序批式膜生物反应器耦合处理干法腈纶废水

采用Fenton氧化-序批式膜生物反应器(SBMBR)组合工艺处理干法腈纶废水。结果表明,在废水初始pH值为3.0,H2O2投加量为90.0 mmol/L,Fe2+投加量为20.0 mmol/L,反应时间为2.0 h的条件下,Fenton氧化预处理对腈纶生产废水的COD去除率达到47.0%以上,COD由1 091 mg/L降至560 mg/L,废水的BOD5/COD由0.32升至0.69,废水的可生化性得到显著提高。Fenton处理出水与丙烯腈废水等比例混合后,采用SBMBR进行生化处理,在水力停留时间为24 h,90 min缺氧/150 min好氧交替运行的条件下,COD、NH4+-N和TN的平均去除率分别为71.7%、97.2%和47.4%,碳源不足是限制TN去除效果的主要影响因素。在无外加碳源的条件下,组合工艺处理后出水COD和NH4+-N浓度分别为117 mg/L和1.7 mg/L,出水水质可以稳定达到国家一级排放标准(GB8978-1996)。     

固定化氨氮降解菌处理氨氮废水的试验研究

考察了海藻酸钠(SA)和聚乙烯醇(PVA)含量对固定化载体性能的影响,并筛选了最优条件制备固定化氨氮降解菌,研究其对氨氮废水的处理效果。当PVA和SA质量分数分别为8.00%、1.00%时,制成的固定化载体抗压性能最好,能够形成丰富的多孔结构。固定化氨氮降解菌在处理氨氮废水前驯化168h,可以恢复较高活性。在固定化氨氮降解菌投加量2%(质量分数)、反应温度30℃、pH 8.01、溶解氧3.0 mg/L的条件下反应60h,氨氮废水中的氨氮质量浓度从最初的3 835.29 mg/L降为82.35mg/L,去除率为97.85%。固定化氨氮降解菌在投加量低于氨氮降解菌的情况下,仍然能实现与之相近的氨氮废水处理效果,证明固定化氨氮降解菌能高效处理高浓度氨氮废水。     

吸附融合菌的固定化及对铬吸附特性研究

研究了融合菌的固定化方法及吸附特性,结果表明:1.5%海藻酸钠为包埋剂包埋50 g/L融合菌可制成物理和吸附性能较好的固定化吸附剂;40 g/L(约含5 g/L融合菌)的固定化吸附剂对30 mg/L含Cr废水的去除率可达94.54%;当投加量为50 g/L(约含6 g/L融合菌)时,固定化吸附剂可完全去除实际电镀废水(pH:2.67,Cu:1.70 mg/L,Cr:20.62 mg/L,N i:29.97 mg/L,Zn:1.11 mg/L)中的Cu和Cr,且对N i和Zn的去除率也分别达到了48.05%和61.09%;吸附过程符合准二级吸附动力学模型;填充柱工艺适用于固定化吸附剂连续处理含铬废水,当流速为150 mL/h和250 mL/h时填充柱一次稳定处理水量分别为7.2 L和11.5 L,且延长水力停留时间可提高出水水质。     

膜生物反应器—O_3催化氧化—曝气生物滤池处理化工园区综合废水的中试研究

以某化工园区污水处理厂综合废水为对象,采用"膜生物反应器(MBR)—O_3催化氧化—曝气生物滤池(BAF)"组合工艺进行深度处理。结果表明:(1)MBR适宜的DO、混合液悬浮固体质量浓度(MLSS)分别为3、3 000~4 000 mg/L。粉末活性炭(PAC)的投加对COD的去除有明显促进作用,并可提高系统的抗冲击负荷,延缓MBR膜通量的下降速率,减少溶解性微生物产物和胞外聚合物的积累,有效缓解膜污染。(2)采用O_3催化氧化作为BAF的前处理单元,可节约30%(质量分数)的O_3投加量,BAF出水COD和氨氮平均去除率分别提高9.9、5.1百分点。(3)在PAC投加量100mg/L、O_3投加量50mg/L、O_3接触氧化时间2h、BAF水力停留时间6h的条件下,组合工艺出水COD、氨氮、TP平均分别为76.5、3.6、0.4mg/L,达到江苏省《化学工业主要水污染物排放标准》(DB 32/939—2006)一级标准。而且,废水中特征有机污染物得到有效降解,应急毒性有较大程度降低。     

圆球型电石渣反应料处理煤矿酸性废水

采用电石渣制备成圆球型反应料,通过多级处理式实验装置对煤矿酸性废水进行处理。研究了在不曝气和曝气2组实验情况下处理出水的pH变化特征和反应料去除铁、锰的效果。结果表明,在不曝气组,当水力停留时间(HRT)为17.6 h,总出水pH值由进水2.84~2.95提高到4.17~11.88,总出水铁平均浓度80.43 mg/L,平均去除率为72.87%,锰平均浓度6.16 mg/L,平均去除率48.21%。在曝气组,当HRT为17.6 h,曝气量为10.50 L/min,总出水pH值由进水2.84~3.00提高到9.10~11.87,总出水铁平均浓度0.03 mg/L,平均去除率为99.99%,锰平均浓度0.14 mg/L,平均去除率为98.72%。因此,利用圆球型电石渣反应料去除煤矿酸性废水中的铁、锰以及提高pH有很好的效果。     

外循环式UASB反应器处理槟榔废水

在中温（35±2℃）条件下,利用外循环式UASB反应器处理中高有机浓度的槟榔加工废水,并着重探讨了水力停留时间（HRT）对厌氧消化的影响。研究表明,当反应器稳定运行,水力停留时间为1 d,进水COD浓度5 000 mg/L左右,容积负荷在2.53-5.25 kg COD/（m3·d）时,COD去除率在38%以上,出水COD〈3 000 mg/L,平均产气率为0.41 m3/kg COD;若水力停留时间延长至4 d,容积负荷为1.26-1.30 kg COD/（m3·d）,COD去除率可以达到79%,出水COD〈1 200 mg/L,出水可生化性下降,BOD5/COD平均为0.28,实验取得了良好的处理效果,为利用厌氧技术处理槟榔加工废水提供了设计依据。     

好氧颗粒污泥自生动态膜生物反应器处理碱减量印染废水

自生动态膜生物反应器(SFDMBR)接种颗粒污泥启动,研究溶解氧浓度和水力停留时间对该反应器处理碱减量印染废水的影响。自生动态膜生物反应器形成稳定的动态膜后,出水浊度小于10 NTU,系统对浊度的去除率在90%以上,溶解氧和水力停留时间对反应器出水浊度基本无影响。系统对废水色度的去除率随着溶解氧浓度的提高和水力停留时间的延长而增加,但是系统对色度的去除效率一般不超过40%。溶解氧浓度由0.3 mg/L逐渐增大至2.4 mg/L,COD的去除率由40%提升至80%,而当溶解氧浓度大于1.0 mg/L后,UV254的去除率达到95%。水力停留时间在8~48 h时,COD去除效率由65%逐渐上升至85%左右;水力停留时间在8~32 h,UV254去除效率为68%~93%,超过32 h后水力停留时间对UV254去除效率的影响已不明显。     

固定化活性污泥去除氨氮废水

采用PVA冷冻-解冻法固定传统活性污泥,用无机硝化菌培养基对其进行活性恢复和驯化培养.用该法制备的固定化活性污泥颗粒在三相流化床中处理氨氮废水,结果表明固定化活性污泥颗粒可处理低浓度氨氮废水,当氨氮浓度为60mg/L左右,固定化颗粒填充率9%,水力停留时间8 h,COD为400mg/L时,NH4+-N去除率达82.5%以上.实验还表明,该法制作的活性污泥颗粒寿命在3个月以上.     

二氧化氯泡沫分离法处理水合肼类废液

采用二氧化氯泡沫分离装置,研究了二氧化氯泡沫分离法对水合肼类废液的处理效果.通过实验重点考察了废水pH值、二氧化氯投加量和反应时间等参数对废水处理效果的影响.在最佳反应条件(即pH值为10,每升废水中二氧化氯的投加量为5 mg/1 000 COD、反应时间为3 h)下进行反应,原废液(COD值为30 000～35 000 mg/L,氨氮总量为2 500～2 700 mg/L)经处理后COD去除率达到99%,氨氮去除率达到96%以上.     

微生物生理群在猪粪秸秆高温堆肥碳氮转化中的作用

在自制的强制通风静态堆肥反应箱中,猪粪与秸秆以鲜重7∶1的比例进行了堆肥化实验,在堆制的23 d里根据堆温变化分阶段采集堆肥样品,利用MPN法测定了堆料中纤维素分解菌和氮素微生物生理群的数量变化,同时测定了相应的碳、氮含量。结果表明,纤维素分解菌在稳定腐熟阶段较多,对于后期有机碳的降解和腐殖质含量的增大起了很大的作用,在堆制的23 d里,腐殖质增加了2.4%。整个堆制过程中,氨化细菌的数量最大且与氨气释放浓度和铵态氮含量呈显著正相关,都在高温期增加,降温期后减少,氨化细菌的数量在高温期的增加率远高于降温期后的减少率,而铵态氮在高温期的增加率远低于在降温后期的减少率,铵态氮总体上减少了74.1%;亚硝化细菌数量与硝态氮呈正相关;反硝化细菌数量在降温期上升幅度较大,堆制结束时为堆制初期的13倍,且与堆肥中硝态氮含量呈正相关;硝态氮含量增加了87.5%;堆肥后期硝态氮的增加可能与堆肥中存在能进行硝化作用的反硝化细菌有关。固氮菌数量在堆制结束时达堆制初期的2.61倍,主要在降温期增加较多,对堆肥中有机氮的形成起很大作用。     

Growth and foliar nitrogen status of four plant species exposed to atmospheric ammonia

A chamber study was conducted to evaluate the growth response and leaf nitrogen (N) status of four plant species exposed to continuous ammonia (NH3) for 12 weeks (wk). This was intended to evaluate appropriate plant species that could be used to trap discharged NH3 from the exhaust fans in poultry feeding operations before moving off-site. Two hundred and forty bare-root plants of four species (Juniperus virginiana (red cedar), Gleditsia triacanthos var. inermis (thornless honey locust), Populus sp. (hybrid poplar), and Phalaris arundinacea (reed canary grass) were transplanted into 4- or 8-L polyethylene pots and grown in four environmentally controlled chambers. Plants placed in two of the four chambers received continuous exposure to anhydrous NH3 at 4 to 5 ppm while plants in another two chambers received no NH3. In each of the four chambers, 2 to 4 plants per species received no fertilizer while the rest of the plants were fertilized with a 100 ppm solution containing 21% N, 7% phosphorus, and 7% potassium. The results showed that honey locust was the fastest-growing species. The superior growth of honey locust among all species was also supported by its total biomass, root, and root dry matter (DM) weights. For all species there was a trend for plants exposed to NH3 to have greater leaf DM than their non-exposed counterparts at 6 (43.0 vs. 30.8%; P = 0.09) and 12 wk (47.9 vs. 36.6%; P = 0.07), and significantly greater (P 相似文献   

Two-stage biofilter for effective NH3 removal from waste gases containing high concentrations of H2S

A high H2S concentration inhibits nitrification when H2S and NH3 are simultaneously treated in a single biofilter. To improve NH3 removal from waste gases containing concentrated H2S, a two-stage biofilter was designed to solve the problem. In this study, the first biofilter, inoculated with Thiobacillus thioparus, was intended mainly to remove H2S and to reduce the effect of H2S concentration on nitrification in the second biofilter, and the second biofilter, inoculated with Nitrosomonas europaea, was to remove NH3. Extensive studies, which took into account the characteristics of gas removal, the engineering properties of the two biofilters, and biological parameters, were conducted in a 210-day operation. The results showed that an average 98% removal efficiency for H2S and a 100% removal efficiency for NH3 (empty bed retention time = 23-180 sec) were achieved after 70 days. The maximum degradation rate for NH3 was measured as 2.35 g N day(-1) kg of dry granular activated carbon(-1). Inhibition of nitrification was not found in the biofilter. This two-stage biofilter also exhibited good adaptability to shock loading and shutdown periods. Analysis of metabolic product and observation of the bacterial community revealed no obvious acidification or alkalinity phenomena. In addition, a lower moisture content (approximately 40%) for microbial survival and low pressure drop (average 24.39 mm H2O m(-1)) for system operation demonstrated that the two-stage biofilter was energy saving and economic. Thus, the two-stage biofilter is a feasible system to enhance NH3 removal in the concentrated coexistence of H2S.     

Long-term operation of a biofilter for simultaneous removal of H2S and NH3

Simultaneous removal of NH3 and H2S was investigated using two types of biofilters--one packed with wood chips and the other with granular activated carbon (GAC). Experimental tests and measurements included analyses of removal efficiency (RE), metabolic products, and results of long-term operation (around 240 days). The REs for NH3 and H2S were 92 and 99.9%, respectively, before deactivation. After deactivation, the RE for NH3 and H2S were decreased to 30-50% and 75%, respectively. The activity of nitrifying bacteria was inhibited by high concentrations of H2S (over 200 ppm) but recovered gradually after H2S addition was ceased. However, the Thiobacillus thioparus as sulfur oxidizing bacteria did not show inhibition at the NH3 concentration under 150-ppm conditions. The deactivation of the biofilter was caused by metabolic products [elemental sulfur and (NH4)2SO4] accumulating on the packing materials during the extended operation. The removal capacities for NH3 and H2S were 6.0-8.0 and 45-75 mg N, S/L/hr, respectively.     

Diagnostic indicators of elevated nitrogen deposition

Tissue N content of mosses, which has been shown to be an indicator of enhanced N, was studied at a range of locations dominated either by wet or dry deposited and oxidised and reduced forms of N. Tissue N responded differently to wet and dry deposited N. For a 1 kg ha(-1) y(-1) increase in N deposition, tissue N increased by 0.01% at wet deposition sites but by 0.03% at sites dominated by dry deposited NH3. Tissue N at wet deposition sites responded more to concentrations of NO3- and NH4+ in precipitation (r(2) 0.63) than to total N deposition (r(2) 0.27), concentration explaining 66% of the variation in tissue N, wet deposition 33%. The study clearly concludes that tissue N concentration in mosses provides a good indication of N deposition at sites where deposition is dominated by NH3, and is also valuable in identifying vegetation exposed to large concentrations of NH4+ or NO3-, in wet deposition dominated areas, such as hilltops and wind exposed woodland edges.     

连续流反应器污水硝化过程中的N_2O释放

污水生物脱氮硝化阶段是温室气体一氧化二氮（N2O）的重要释放源。采用连续流反应器在2种进水氨氮（NH4-N,低氮反应器60 mg/L和高氮反应器180 mg/L）浓度条件下驯化硝化菌,并研究了不同初始NH4-N浓度和不同初始亚硝酸盐（NO2-N）浓度条件下所驯化硝化菌释放N2O的特征。结果表明在反应器运行过程中2个反应器释放N2O较少,均小于去除NH4-N浓度的0.01%;N2O的释放均随着初始NH4-N浓度或初始NO2-N浓度的升高而增加;不同初始NH4-N浓度条件下,低氮反应器驯化硝化菌的N2O释放率在0.51%~1.40%之间,高氮反应器驯化硝化菌在0.29%~1.27%之间;不同初始NO2-N浓度条件下,低氮反应器驯化硝化菌的N2O释放率在1.38%~3.78%之间,高氮反应器驯化硝化菌在1.16-5.81%之间。     

Vegetative buffers for fan emissions from poultry farms: 2. ammonia, dust and foliar nitrogen

This study evaluated the potential of trees planted around commercial poultry farms to trap ammonia (NH(3)) and dust or particulate matter (PM). Norway spruce, Spike hybrid poplar, hybrid willow, and Streamco purpleosier willow were planted on five commercial farms from 2003 to 2004. Plant foliage was sampled in front of the exhaust fans and at a control distance away from the fans on one turkey, two laying hen, and two broiler chicken farms between June and July 2006. Samples were analyzed for dry matter (DM), nitrogen (N), and PM content. In addition, NH(3) concentrations were measured downwind of the exhaust fans among the trees and at a control distance using NH(3) passive dosi-tubes. Foliage samples were taken and analyzed separately based on plant species. The two layer farms had both spruce and poplar plantings whereas the two broiler farms had hybrid willow and Streamco willow plantings which allowed sampling and species comparisons with the effect of plant location (control vs. fan). The results showed that NH(3) concentration h(- 1) was reduced by distance from housing fans (P < or = 0.0001), especially between 0 m (12.01 ppm), 11.4 m (2.59 ppm), 15 m (2.03 ppm), and 30 m (0.31 ppm). Foliar N of plants near the fans was greater than those sampled away from the fans for poplar (3.87 vs. 2.56%; P < or = 0.0005) and hybrid willow (3.41 vs. 3.02%; P < or = 0.05). The trends for foliar N in spruce (1.91 vs. 1.77%; P = 0.26) and Streamco willow (3.85 vs. 3.33; P = 0.07) were not significant. Pooling results of the four plant species indicated greater N concentration from foliage sampled near the fans than of that away from the fans (3.27 vs. 2.67%; P < or = 0.0001). Foliar DM concentration was not affected by plant location, and when pooled the foliar DM of the four plant species near the fans was 51.3% in comparison with 48.5% at a control distance. There was a significant effect of plant location on foliar N and DM on the two layer farms with greater N and DM adjacent to fans than at a control distance (2.95 vs. 2.15% N and 45.4 vs. 38.2% DM, respectively). There were also significant plant species effects on foliar N and DM with poplar retaining greater N (3.22 vs. 1.88%) and DM (43.7 vs. 39.9%) than spruce. The interaction of location by species (P < or = 0.005) indicated that poplar was more responsive in terms of foliar N, but less responsive for DM than spruce. The effect of location and species on foliar N and DM were not clear among the two willow species on the broiler farms. Plant location had no effect on plant foliar PM weight, but plant species significantly influenced the ability of the plant foliage to trap PM with spruce and hybrid willow showing greater potential than poplar and Streamco willow for PM(2.5)(0.0054, 0.0054, 0.0005, and 0.0016 mg cm(- 2); P < or = 0.05) and total PM (0.0309, 0.0102, 0.0038, and 0.0046 mg cm(- 2), respectively; P < or = 0.001). Spruce trapped more dust compared to the other three species (hybrid willow, poplar, and Streamco willow) for PM(10) (0.0248 vs. 0.0036 mg cm(- 2); P < or = 0.0001) and PM(> 10) (0.0033 vs. 0.0003 mg cm(- 2); P = 0.052). This study indicates that poplar, hybrid willow, and Streamco willow are appropriate species to absorb poultry house aerial NH(3)-N, whereas spruce and hybrid willow are effective traps for dust and its associated odors.     

Laboratory analyses of 137Cs uptake by sunflower, reed and poplar

The 137Cs uptake by three plant species (Phragmites australis L., Heliantus annus L., Populus simonii L.) was analyzed in a hydroponic medium (14 MBql(-1); 0.5 mM CsCl) during cultivation. The radioactivity disappearance from the medium was measured after 2, 4, 8, 16 and 32 days of cultivation. Radioactivity distribution within the plant was determined by autoradiography. We did not find differences between uptake of radioactive and stable caesium isotopes. Relations between the uptake of 137Cs and concentration of potassium and ammonium ions in medium were also tested. The highest uptake of radiocaesium by sunflower was obtained for medium with 1 mM K2SO4 (14.2%) and in case of ammonium ions for concentration ratio 6 mM NH4Cl : 3 mM NH4NO3 (13.2%). The obtained results make it possible to compare the capability and rate of 137Cs phytoremediation of different plant species.     

Fate of nitrogen during composting of chicken litter

Chicken litter (a mixture of chicken manure, wood shavings, waste feed, and feathers) was composted in forced-aeration piles to understand the changes and losses of nitrogen (N) during composting. During the composting process, the chemical [different N fractions, organic matter (OM), organic carbon (C), and C:N ratio], physical, and microbial properties of the chicken litter were examined. Cumulative losses and mass balances of N and organic matter were also quantified to determine actual losses during composting. The changes in total N concentration of the chicken litter piles were essentially equal to those of the organic N. The inorganic N concentrations were low, and that organic N was the major nitrogenous constituent. The ammonium (NH(4)(+))-N concentration decreased dramatically during first 35 days of composting. However, the rapid decrease in NH(4)(+)-N during composting did not coincide with a rapid increase in (NO(3)(-)+NO(2)(-))-N concentration. The concentration of (NO(3)(-)+NO(2)(-))-N was very low (<0.5 g kg(-1)) at day 0, and this level remained unchanged during the first 35 days of composting suggesting that N was lost during composting. Losses of N in this composting process were governed mainly by volatilization of ammonia (NH(3)) as the pile temperatures were high and the pH values were above 7. The narrow C:N ratio (<20:1) have also contributed to losses of N in the chicken litter. The OM and total organic C mass decreased with composting time. About 42 kg of the organic C was converted to CO(2). On the other hand, 18 kg was lost during composting. This loss was more than half (59%) of the initial N mass of the piles. Such a finding demonstrates that composting reduced the value of the chicken litter as N fertilizer. However, the composted chicken contained a more humified (stabilized) OM compared with the uncomposted chicken litter, which would enhance its value as a soil conditioner.     

Characterization of atmospheric PM10 and related chemical species in southern Taiwan during the episode days

The concentrations of atmospheric PM10 on days with episodes of pollution were examined at four different sampling sites (CC, DL, LY, and HK) in southern Taiwan. The related to particulates water-soluble ionic species (Na+, K+, Mg2+, Ca2+, NH4+, Cl-, NO3-, SO4(2-)), carbonaceous species (EC and OC) and metallic species (Zn, Ni, Pb, Fe, Mn, Al, Si, V) were also analyzed. On the episode days of this study, the PM10 mass concentration ranged from 155 to 210 microgm(-3), from 150 to 208 microgm(-3), from 182 to 249 microgm(-3), and from 166 to 228 microgm(-3) at CC, DL, LY, and HK, respectively. The results indicate that the dominant water-soluble species were SO4(2-), NO3-, NH4+, and Cl- at the four sampling sites on these days. Moreover, the high sulfate and nitrate conversion values (SOR and NOR) presented herein suggest that secondary formations from SO2 to SO4(2-) and from NO2 to NO3- are present in significant quantities in the atmosphere of southern Taiwan on episode days. In particular, high SOR and NOR verified that both SO4(2-) and NO3- dominated the increase of atmospheric PM10 concentration in southern Taiwan on episode days.