非离子型聚丙烯酰胺絮凝剂的制备及其絮凝性能

以丙烯酰胺（AM）和烷基酚聚醚（APAP）为单体,采用反相乳液聚合法制备了流动性好的非离子型聚丙烯酰胺絮凝剂（PAM-APAP）。考察了乳化剂和引发剂的种类、单体总质量分数、单体配比和反应温度等因素对聚合反应的影响。实验结果表明,制备PAM-APAP的最佳工艺条件为：单体总质量分数35%、m（AM）∶m（APAP）=9.0∶1.0、Span80+Tween80复配乳化剂加入量为油水总质量的7%、m（Span80）∶m（Tween80）=7.0∶1.5、V50加入量为单体总质量的1.5‰、反应温度50℃。PAM-APAP具有较好的絮凝效果,与其他絮凝剂相比用量较少,在加入量为100mg/L时,对聚合物驱油中产生的含聚合物污水的浊度去除率为87.9%,去油率为89.5%,且絮体不黏壁。     

Purification and Properties of Extracellular Poly(3-hydroxybutyrate) Depolymerase Produced by <Emphasis Type="Italic">Aspergillus fumigatus</Emphasis> 202

An extracellular poly(3-hydroxybutyrate) (PHB) depolymerase produced by a thermotolerant fungal soil isolate, Aspergillus fumigatus 202, was purified and characterized. Maximum PHB depolymerase production was obtained at the end of 48 h with initial medium pH 7.0 and 45 °C in Bushnell Haas Minerals medium containing PHB as sole source of carbon. The PHB depolymerase was purified using size exclusion chromatography to a fold purification of 20.62 and 61.62% yield. SDS-PAGE and isoelectric focusing revealed the molecular weight and pI of the purified enzyme as 63,744 Da and 4.2, respectively. N-terminal amino acid sequence of purified enzyme was HAXDAYLVK. This non-glycosylated enzyme was most active at pH 9.0 and 45 °C. Purified enzyme was inactivated by N-bromosuccinimide and dithiothreitol suggesting the involvement of tryptophan residues and disulfide bonds at its active site. Nonionic detergents like Tween 20, Tween 80 and Triton X-100 inhibited the enzyme activity. Ions like Ca⁺² and Mg⁺² (5 mM) increased the enzyme activity 1.5 times. Fe⁺² effectively inhibited the enzyme activity to 88% whereas Hg⁺² completely inhibited the enzyme.     

Tween 20 and Its Major Free Fatty Acids as Carbon Substrates for the Production of Polyhydroxyalkanoates in Pseudomonas aeruginosa ATCC 27853

The ability of Pseudomonas aeruginosa ATCC 27853 to grow and synthesize polyhydroxyalkanoates (PHAs) using Tween 20 as the sole carbon source was investigated. Tween 20 could support cell growth and PHA production. The polymer produced from Tween 20 was compared with those produced from its major free fatty acids components: lauric (C₁₂), myristic (C₁₄), and palmitic (C₁₆) acids. Gas-chromatographic analysis of methanolyzed samples and ¹³C-Nuclear Magnetic Resonance (NMR) showed that the PHAs obtained are composed of even carbon atoms 3-hydroxyalkanoates ranging from C₆ to C₁₄, with C₈ and C₁₀ as the predominant components. The nature of the carbon sources used had little influence on the composition, but was found to be important in determining the average molecular weight, shorter chain fatty acids yielding higher molecular weight products. Fast Atom Bombardment-Mass Spectrometry (FAB-MS) of partially pyrolyzed samples, coupled to statistical analysis, showed that these PHAs are random copolymers.     

Enhanced biodegradation of creosote-contaminated soil

Bioremediation, a viable option for treatment of cresote-contaminated soil, can be enhanced by the use of surfactant. A study was conducted to investigate the effect of a non-ionic surfactant, Triton X-100, on biodegradation of creosote-contaminated soil. Abiotic soil desorption experiments were performed to determine the kinetics of release of selected polynuclear aromatic hydrocarbon (PAH) compounds. Respirometric experiments were also conducted to evaluate the effect of nonionic surfactant on biodegradation. The N-Con system respirometer was used to monitor the oxygen uptake by the microorganisms. The abiotic experiments results indicated that the addition of surfactant to soil/water systems increased the desorption of PAH compounds. It was also observed that the desorption rate of PAH compounds depended on their molecular weight. The 3- and 4-ring PAH compounds showed higher and faster desorption rates than the 5- and 6-ring PAHs. The respirometric experiments indicated that an increase in soil contamination level from 112.5 to 771.8 mg/kg showed an increase in oxygen uptake. But for a soil contamination level of 1102.5 mg/kg, the oxygen uptake was similar to the contamination level of 771.8 mg/kg. This might be due to toxicity by the surfactant or the solubilized PAHs at high concentration or interference with contaminant transport into the cell or to reversible physical-chemical interferences with the activity of enzymes involved in the PAH degradation. The increase in PAH availability to the microorganisms in the aqueous phase produced an increase in oxygen consumption that is proportional to the biodegradation of organic compounds.     

有机溶剂浸取石油污染土壤中的多环芳烃

采用索氏提取法和气相色谱分析了某炼油厂周边土壤中的多环芳烃的种类及含量,考察了6种有机溶剂对土壤中多环芳烃的浸取效果,探讨了溶剂与溶质溶解度参数差异对浸取效果的影响。结果表明：土壤试样中含有蒽、荧蒽、芘、 、苯并[a]蒽、苯并[b]荧蒽、苯并[k]荧蒽和苯并[a]芘8种多环芳烃,其含量分别为4.20,22.05,10.62,4.26,5.54,0.80,0.94,4.18 mg/kg;筛选出二氯甲烷作为土壤中多环芳烃的浸取溶剂;最佳浸取条件为浸取时间10 min、浸取温度30 ℃、溶剂与土壤的液固比5:1（mL/g）、土壤含水量8%,在此条件下,总多环芳烃浸出率为83.0%,各种多环芳烃的浸出率分别为蒽97.8%、荧蒽78.2%、芘99.9%、 98.5%、苯并[a]蒽81.1%、苯并[b]荧蒽47.6%、苯并[k]荧蒽14.8%、苯并[a]芘58.7%。     

Literature overview: Microbial metabolism of high molecular weight polycyclic aromatic hydrocarbons

High molecular weight polycyclic aromatic hydrocarbons (HMW PAHs) increase in hydrophobicity with increases in their molecular weight and ring angularity. Microbial strategies to deal with PAH hydrophobicity include biofilm formation, enzyme induction, and biosurfactants, the effect of which is variable on PAH metabolism depending on the surfactant type and concentration, substrate, and microbial strain(s). Aerobic HMW PAH metabolism proceeds via mineralization, partial degradation, and cometabolic transformations. Generally, bacteria and nonlignolytic fungi metabolize PAHs via initial PAH ring oxidation by dioxygenases to form cis‐dihydrodiols, which are transformed to catechol compounds by dehydrogenases and other mono‐ and dioxygenases to substituted catechol and noncatechol compounds, all ortho‐ or metacleaved and further oxidized to simpler compounds. However, lignolytic fungi form quinones and acids to CO₂. This review discusses the pathways for HMW PAH microbial metabolism. © 2008 Wiley Periodicals, Inc.     

Biodegradation Study of Starch-graft-Acrylonitrile Copolymer

In this study the biodegradability of starch-graft-acrylonitrile (St-g-AN) copolymer has been investigated using some microorganisms including Aspergillus niger. The fungus A. niger was isolated from the soil and from the wastewater of an acrylic fiber company. The effects of four factors including environment temperature, primary inoculum concentration, pH and weight of copolymer film, on the biomass generation as a measure of biodegradation rate of copolymer, were studied using Taguchi experimental design. The statistical analysis of the results showed that the primary inoculum concentration and temperature were the most important factors affecting the biodegradation of St-g-AN copolymer. The optimum levels of temperature, pH, inoculum concentration, and weight of films to attain the maximum biodegradation (as much as 8.59 % by weight percentage during 28 days) were obtained as 30 °C, 4.75, 10⁸ spore/mL, and 1.1 g, respectively. The changes in the structure and morphological properties of the copolymer before and after degradation were determined using transform infrared spectroscopy and scanning electron microscopy.     

Physicochemical and biochemical changes during composting of different mixing ratios of biogas sludge with palm oil mill wastes and biogas effluent

Prior to composting, the composition of palm oil mill wastes were analyzed. Palm empty fruit bunches (PEFB) contained the highest total organic carbon (52.83 % dry weight) while palm oil mill biogas sludge (POMS) and decanter cake (DC) contained higher total nitrogen (3.6 and 2.37 % dry weight, respectively) than the others. In addition, palm oil fuel ash (POFA) had a high amount of phosphorus and potassium (2.17 and 1.93 % dry weight, respectively). The effect of mixture ratio of POMS and other palm oil mill wastes for composting was studied using the mixed culture Super LDD1 as an inoculum. All compost piles turned dark brown and attained an ambient temperature after 40 days incubation. The pH values were stable in the range of 6.9–7.8 throughout the process whereas the moisture content tended to decrease till the end with the final value around 30 %. After 60 days incubation, the mixture ratio of POMS:PEFB:DC at 2:1:1 with the addition of biogas effluent gave the highest quality of the compost. Its nitrogen content was 31.75 % higher than the other treatments that may be a result of growth of ink cap mushroom (Coprinus sp.). This is the first report on the occurrence of this mushroom during composting. In addition, its nutrients (3.26 % N, 0.84 % P and 2.03 % K) were higher than the level of the Organic Fertilizer Standard. The mixed culture Super LDD1 produced the highest activity of CMCase (6.18 Unit/g) and xylanase (11.68 Unit/g) at 9 days fermentation. Therefore, this solid-state fermentation could be employed for production of compost as well as enzymes.     

Evaluation of in situ steam‐injection processes for reduction of petroleum compounds within an abandoned canal

A conceptual approach of a novel application of in‐situ thermal processes that would either use a steam injection process or a steam/surfactant injection process was considered to remediate petroleum contaminated sediment residing in an abandoned canal. Laboratory tests were conducted in an attempt to volatilize or mobilize contaminants of concern (selected polycyclic aromatic hydrocarbons [PAHs]) from the contaminated sediment into a phase that could be physically removed. The processes were operated above ambient temperature and pressure in an attempt to increase the removal of the contaminants of concern from the sediment. The ability of both the steam injection process and the steam/surfactant process to remove PAHs from the sediment was considered ineffective; as only two of the seventeen selected PAHs (naphthalene and C1 naphthalene) were associated with a percentage mass reduction greater than 34% for both treatments (four trials). The steam/surfactant injection process generally resulted in higher reductions than the steam injection process, but had larger variances within the two trials using the treatment type. This preliminary evaluation suggests that steam‐based injection processes for removing petroleum contamination from this canal sediment, using the surfactants selected, equipment set‐up, and operating conditions studied, would be considered ineffective. © 2010 Wiley Periodicals, Inc. *

1 This article is a U.S. Government work and, as such, is in the public domain of the United States of America.

     

Effect of Interfacial Modifiers on Mechanical and Physical Properties of the PHB Composite with High Wood Flour Content

To explore the commercial viability of Polyhydroxybutyrate (PHB)/wood flour (WF) composites, systems were produced at industry-standard levels of fiber loading. Further, four interfacial modifiers were selected to improve the mechanical properties of PHB/WF composites, including maleated PHB (PHB-g-MA), a low molecular weight epoxy, a low molecular weight polyester, and polymethylene-diphenyl-diisocyante (pMDI). Results showed that all modifiers resulted in improvements in tensile strength and modulus, however, pMDI showed the highest improvements. The pMDI modifier also improved water uptake of the composites. Study of the fracture surfaces showed signs of improved fiber bonding, as did morphological studies by dynamic mechanical analysis (DMA), and differential scanning calorimetry (DSC). Interpretation of the DSC and DMA results indicate possible reactions with lubricant, and interactions between PHB and wood fibers with the addition of pMDI.     

Biodegradable Poly(lactic acid) Blends with Chemically Modified Polyhydroxyoctanoate Through Chain Extension

Poly(lactic acid) (PLA) was blended with chemically modified Polyhydroxyoctanoate (mPHO) using a Haake twin-screw mixer. Due to the melt viscosity disparity between the two components, PHO was reacted with Hexamethylene diisocyanate (HDI) used as a chain extender to produce high molecular weight for improving compatibility and processability with PLA. The number average and weight average molecular weight of the PHO, reacted with 0.55 wt% HDI, were increased 314 and 275%, respectively, compared with those of the unmodified PHO. The blends were characterized for rheological, thermal, and mechanical properties. Infrared spectra confirmed the formation of the urethane linkages in mPHO. The shear viscosity, as a function of shear rate or shear stress, decreased with an increase in mPHO content, indicating that the PLA/mPHO blends show shear-thinning behavior along with the power-law model. DSC thermograms showed that the two components in the blends were found with two crystalline phases and two amorphous phases confirming the coexistence of two immiscible components. Tensile results indicated that tensile strength for blends decreased with increasing mPHO content up to 80%. A decrease in elastic modulus, as well as an increase in elongation at break, was seen as a function of mPHO content. Results of aging tests showed that the mechanical properties of the blends also dropped more at a higher PLA level when compared with those of the unaged samples.     

Remediation of Soil and Ground Water Contaminated with PAH using Heat and Fe(II)-EDTA Catalyzed Persulfate Oxidation

The feasibility of degrading 16 USEPA priority polycyclic aromatic (PAH) hydrocarbons (PAHs) with heat and Fe(II)-EDTA catalyzed persulfate oxidation was investigated in the laboratory. The experiments were conducted to determine the effects of temperature (i.e. 20 ^∘C, 30 ^∘C and 40 ^∘ C) and iron-chelate levels (i.e., 250 mg/L-, 375 mg/L- and 500 mg/L-Fe(II)) on the degradation of dissolved PAHs in aqueous systems, using a series of amber glass jars as the reactors that were placed on a shaker inside an incubator for temperature control. Each experiment was run in duplicate and had two controls (i.e., no persulfate in systems). Samples were collected after a reaction period of 144 hrs and measured for PAHs, pH and sodium persulfate levels. The extent of degradation of PAHs was determined by comparing the data for samples with the controls. The experimental results showed that persulfate oxidation under each of the tested conditions effectively degraded the 16 target PAHs. All of the targeted PAHs were degraded to below the instrument detection limits (∼4 μ/L) from a range of initial concentration (i.e., 5 μ/L for benzo(a)pyrene to 57 μ/L for Phenanthrene) within 144 hrs with 5 g/L of sodium persulfate at 20 ^∘ C, 30 ^∘C and 40 ^∘C. The data indicated that the persulfate oxidation was effective in degrading the PAHs and that external heat and iron catalysts might not be needed for the degradation of PAHs. The Fe(II)-EDTA catalyzed persulfate also effectively degraded PAHs in the study. In addition, the data on the variation of persulfate concentrations during the experiments indicated that Fe(II)-EDTA accelerated the consumption of persulfate ions. The obtained degradation data cannot be used to evaluate the influence of temperature and Fe(II) levels on the PAH degradation because the PAHs under each of the tested conditions were degraded to below the instrument detection limit within the first sampling point. However, these experiments have demonstrated the feasibility of degrading PAHs in aqueous systems with persulfate oxidation. Additional tests are being conducted to evaluate the effectiveness of treating PAHs in soils and obtaining the rate of degradation of PAHs with persulfate oxidation. Two sets of laboratory experiments were conducted to evaluate the ability of sodium persulfate in oxidizing real world PAH-contaminated soils collected from a Superfund site in Connecticut. The first set of soil sample were treated only with persulfate and to the second batch, mixture of persulfate and Fe(II)-EDTA solutions were added. The results of the second test showed that within 24 hours, 75% to 100% of the initial concentrations of seven PAH compounds detected in the soil samples were degraded by sodium persulfate mixed with FE(II)-EDTA.     

Effects of physicochemical factors on PAH degradation by Planomicrobium alkanoclasticum

Polycyclic aromatic hydrocarbons (PAHs) are environmental pollutants that are mutagenic, carcinogenic, and toxic to living organisms. Here, the ability and effectiveness of selected bacteria isolated from an oil‐contaminated area in biodegrading PAHs were evaluated, and the optimal conditions conducive to bacterial PAH biodegradation were determined. Of six bacterial isolates identified based on their 16S rRNA sequences, Planomicrobium alkanoclasticum could subsist on and consume nearly all hydrocarbons according to the 2,6‐dichlorophenolindophenol assay. The efficacy of this isolate at PAH biodegradation was then empirically confirmed. After 30 days of incubation, P. alkanoclasticum degraded 90.8% of the 16 PAH compounds analyzed and fully degraded eight of them. The optimum P. alkanoclasticum growth conditions were 35°C, pH 7.5, and NaNO₃ as the nitrogen source. Under these biostimulant conditions, P. alkanoclasticum degraded 91.4% of the total PAH concentration and completely decomposed seven PAHs after 15 days incubation. Hence, P. alkanoclasticum is an apt candidate for the biodegradation of PAHs and the bioremediation of sites contaminated by them.     

混合表面活性剂-浊点萃取法测定沉积物中多环芳烃的含量

以混合型表面活性剂（十二烷基硫酸钠（SDS）和对叔辛基苯基聚己二醇醚（Triton X-114））为萃取剂,采用浊点萃取法萃取沉积物中的15种多环芳烃（PAHs）,并利用HPLC技术测定15种PAHs的含量。实验结果表明,当混合型表面活性剂的加入量 3％（w）、混合型表面活性剂中SDS含量 50%（φ）、Na2SO4含量 8％（w）、萃取温度 60 ℃、超声萃取时间 10 min 时,15种PAHs的线性关系良好,r=0.998 9~0.999 7,检出限0.4~8.2 μg/L,加标回收率71.22%~97.36%,相对标准偏差0.92%~4.36%（n=6）。     

The Relationship Between the Chemical Structure of Poly(alkylene glycol)s and Their Aerobic Biodegradability in an Aqueous Environment

The relationship between the chemical structure of poly(alkylene glycol)s (PAGs) and their biodegradability was studied using a set of polymeric fluids that included poly(ethylene glycol), poly(propylene glycol) (PPG), random copolymers of ethylene oxide (EO) and propylene oxide (PO) differing in the EO/PO ratio as well as PAGs capped with ether or acyl moieties. The PAGs that were tested had an average molecular weight (MW) in the range of 350–3,600 Da and differed in their polymer backbones by either linear (diol type) or branched (triol type) molecules. The ultimate biodegradability of the PAGs was determined according to ISO 14593 (CO₂ headspace test) with a non-pre-exposed (as in OECD 310 test) and pre-exposed (adapted) inoculum. PAGs with the structure of PPG and copolymers of EO/PO of diol or triol structures with average molecular weights lower than 1,000 Da can be considered as readily biodegradable. Their ultimate biodegradation exceeds the limit of 60 % (according to the criteria of the OECD 310 test). PAGs with a copolymer structure and MW values ranging between 1,000 and 3,600 Da are not readily biodegradable, but they can be considered as those of inherent ultimate biodegradability. The increased EO content in PAG structures and the acylation of the terminal hydroxyl groups with carboxylic acids favourably influenced their biodegradability. Capped PAGs containing terminal ether groups appeared to be resistant to biodegradation.     

Removal of manganese and zinc from Kahrizak landfill leachate using daily cover soil and lime

The possibility of in situ removal of heavy metals found in leachate generated at municipal solid waste landfills was studied through amendment of daily cover soil. Kahrizak landfill, which receives the waste generated at Tehran, was selected as the source of leachate and soil samples. Manganese and zinc were selected in this study. The soil sample taken from the Kahrizak site contained about 17% clay, which was presumed to have significant capability for removing manganese and zinc. This capability was assumed to be enhanced further through the addition of lime and consequently to improve the potential for chemical precipitation of the selected metals. The in situ removal experiment was accomplished through a set of seven columns filled with the sampled soil with varying contents of lime (i.e., from 0% to 6% by dry weight). Fresh leachate of low pH was added to the columns on a daily basis. Concentrations of manganese and zinc were measured in the influent and effluent during 40 days when biological clogging resulted in a condition of almost no outflow in the columns. The results indicated a substantial increase in removal efficiency through the addition of lime to the daily cover soil. Desorption resulting from the low pH of fresh leachate occurs at later stages compared to the column with no lime addition.     

Destruction of PAHS from soil by using pressurized hot water extraction coupled with supercritical water oxidation

Chemical processes utilizing water both as extraction solvent and reaction medium are promising "Green Chemistry" alternatives to conventional techniques. Equipment for on-line coupled hot water extraction and supercritical water oxidation was constructed to extract polyaromatic hydrocarbons and toluene from sea sand followed by oxidation using hydrogen peroxide. The effectiveness of the technique is based on the physico-chemical properties of heated and pressurized water. Extraction efficiency increased with temperature and time; the best results were obtained at 300 degrees C with 40 min extraction time. In the oxidation stage, conversion of the PAHs increased with reaction time and oxidant concentration and the best conversion (97.0-99.9%, depending on the compound) was obtained at 425 degrees C with 43 s reaction time. Benzaldehyde and benzoic acid were the most abundant reaction intermediates in the oxidation process. In addition, phenol, p-cresol, and benzyl alcohol were found as intermediates. The intermediates originated mainly from toluene, which was present in much greater concentration than PAHs in the reaction medium.     

An experimental study on fermentative H2 production from food waste as affected by pH

Batch dark fermentation experiments were performed on food waste and mixtures of food waste and wastewater activated sludge to evaluate the influence of pH on biological H₂ production and compare the process performance with and without inoculum addition. The effect of a preliminary thermal shock treatment of the inoculum was also investigated as a means to harvest the hydrogenogenic biomass. The best performance in terms of both H₂ generation potential and process kinetics was observed at pH = 6.5 under all experimental conditions (no inoculum, and untreated or thermally treated inoculum added). H₂ production from food waste was found to be feasible even without inoculum addition, although thermal pre-treatment of the inoculum notably increased the maximum production and reduced the lag phase duration. The analysis of the fermentation products indicated that the biological hydrogen production could be mainly ascribed to a mixed acetate/butyrate-type fermentation. However, the presence of additional metabolites in the digestate, including propionate and ethanol, also indicated that other metabolic pathways were active during the process, reducing substrate conversion into hydrogen. The plateau in H₂ generation was found to mirror the condition at which soluble carbohydrates were depleted. Beyond this condition, homoacetogenesis probably started to play a role in the degradation process.     

微生物降解重油的初步研究

丛石油污染的土壤中筛选出一株假单胞菌,考察了其对重油的降解效果。降解18d,重油的降解率达到42．8％,饱和烃、芳香烃、胶质、沥青质的降解率分别为42．95％,43．85％,44．5％,5．55％;质量浓度2．5g／L的表面活性剂Tween-80可使重油的18d降解率达到51．0％;弱碱性条件有利于重油的生物降解;生物泥浆法处理重油污染的土壤,1kg土壤中重油质量100g,降解45d,重油的降解率达到38．85％。     

Catalytic upgrading pyrolysis of pine sawdust for bio-oil with metal oxides

The catalytic upgrading pyrolysis of pine sawdust was performed at 500 °C with various metal oxides to improve the quality of the bio-oil. The aim of this study was to investigate the potential of the metal oxides instead of traditional zeolites for catalytic upgrading pyrolysis with the analysis of Gas Chromatograph/Mass Spectrometer. In this study, the used catalysts were Calcium-oxide, Magnesium oxide, Titanium dioxide, and Zeolite (Si/Al?=?80). The influence of catalysts on products yields and compositions were investigated. Most metal oxides can enhance the bio-gas with the bio-oil yields decreased. The metal oxides led to a decrease of Acids, Aldehydes, Ketones and an increase of Furfural, Cresols, Catechols in Furans and Phenolics. Among the catalysts, the MgO catalysts was the most effective to convert the high molecular into lights ones (6.65% Cresols) with yield of 20.48% for Furfural. The deoxygenation reaction in bio-oil was suggested to convert oxygenated compounds into the low molecular weight of the materials (6.39% Guaiacols). Thus, the used metal oxides can improve the quality of bio-oil by decreasing undesirable compounds as well as increasing the desirable compounds with low oxygen contents via deoxygenation reaction.