用于干式脱污的CaO蒸汽活化实验研究

利用小型活化转炉实验台对以CaO为主要成分的钙基脱污剂在300～650℃的温度范围内进行蒸汽活化处理,结合X射线衍射和压汞仪的分析结果,初步探讨了蒸汽活化的机理.研究表明,蒸汽活化温度在600℃以上时,脱污剂孔隙结构有显著的改善,比孔容积和比表面积有着显著的增加,微孔(＜100nm)的数量大量增加,而低温下蒸汽活化的效果不是十分明显;研究还发现高温下延长活化时间有利于改善脱污剂的孔隙结构.     

热解温度对污泥碳基材料表面性质及吸附性能的影响

以市政污泥为原料,在300、400、500、600、700和800℃无氧气氛下,热解制备了污泥基生物炭。采用BET、SEM、XPS、FT-IR对不同热解温度下污泥炭进行了表征分析;研究了不同热解温度下污泥炭对污水中有机物的吸附效果和动力学;探究了热解温度对污泥炭微观调控下吸附实际水体中有机物的匹配机质。结果表明,随热解温度的升高,C—H、C—C结合比例降低,C=C、C—O=C比例升高,芳香化程度增加,且比表面积、孔容及表面粗超度均有所增加,1～2 nm微孔比例增多,介孔向微孔发展趋势逐渐明显。800℃热解温度条件下制备的污泥炭对二沉池出水中有机物的吸附效果优于其他温度下制备的污泥炭。吸附温度为298.15 K时,最大吸附容量为282.5 mg·g~(-1),且符合准二级吸附动力学。高温下制备的污泥炭对水体中腐殖酸和富里酸具有较强的吸附效能。这主要是由于表面丰富的含氧官能团、芳香键与腐殖酸和富里酸发生了氢键、化学键缔合作用和π-π共轭作用,同时污泥碳表面发达的孔隙结构和较大的比表面积也提供了更多的活性结合位点,促进了污染物的吸附。     

活性炭变温脱附高浓度VOCs的工艺参数优化与评价

以甲苯为VOCs类代表性的目标污染物,通过搭建实验装置模拟活性炭吸附脱附处理VOCs工艺,并在不同工艺条件下(脱附温度、表观风速、高径比),选取常见评价因子(甲苯脱附率、甲苯浓缩比、脱附能耗比)以探讨不同脱附工况下气体对各床层的脱附情况进行研究。结果表明,甲苯脱附率随脱附温度和表观风速的增加而增加。甲苯浓缩比随脱附温度和高径比的增加,随表观风速的减小而增加,即表观风速是浓缩比的主要控制因素。在中温范围内,低风速、高径比的甲苯浓缩比小于高风速、高径比。在高温范围内,低风速、高径比的甲苯浓缩比仅在峰值段大于高风速、高径比。脱附温度越高,表观风速越小,高径比越大,相同脱附率下的甲苯浓缩比越大。脱附能耗比随脱附温度和表观风速的减小,高径比的增加而降低,即表观风速是能耗比的主要控制因素。高温低风速时的能耗比比中温高风速时的能耗比低。当脱附温度80℃、表观风速0.3 m·s^-1时,脱附能耗比最低为1.170 6 kJ·g^-1。本研究可为变温脱附工程化应用的低碳化工艺优化提供参考。     

Fenton活化制备污泥炭对水中Cr(Ⅵ)的吸附性能

利用Fenton活化法活化脱水污泥制备活性炭,研究了Fenton试剂投加量、活化时间、炭化温度、炭化时间和升温速率5种因素对制备污泥炭的影响。污泥炭的最佳制备工艺:Fenton试剂投加量为150 m L,活化时间为2.5 h,炭化温度为350℃,炭化时间为1 h,升温速率为20℃·min-1。污泥炭碘吸附值达到331.90 mg·g-1,BET比表面积为24.265 m~2·g-1。总孔容为0.146 cm~3·g-1,微孔率为17%。分析了吸附时间、pH值和吸附温度3种因素对污泥炭吸附水中Cr(Ⅵ)的影响。在吸附时间为90 min,pH=3,吸附温度为50℃时,污泥炭对Cr(Ⅵ)的吸附量为9.93 mg·g-1。吸附动力学符合准二级动力学模型描述,吸附过程符合Langmuir和Tempkin等温吸附模型描述。     

微波活化对Ca(OH)2孔隙结构及脱氯性能的影响

采用微波炉对一定质量的氢氧化钙样品进行活化,利用压汞仪考察了不同微波活化时间及脱氯反应前后的Ca(OH)2总比孔表面积、分段比表面积和孔径分布的变化,并在脱氯实验台上对脱氯效率进行实际测试.结果表明,微波活化存在一个最佳时间,在此时间内样品比孔表面积增大50%左右,而超过这一时间样品比表面积回复性减小;微波活化主要通过增加3～20 nm孔径段的微孔为样品提供更大比表面积;这些新增加的微孔在脱氯反应过程中被完全利用或消耗;最佳活化时间下的微波活化使Ca(OH)2在较低Ca/Cl摩尔比下获得更大脱氯效率,Ca/Cl摩尔比=4.1时,脱氯效率增加了20%.     

沙柳活性炭纤维的制备与表征

以(NH_4)_2HPO_4活化沙柳纤维制备活性炭纤维,L_(16)(4~5)正交实验优化制备工艺条件,重点研究了活化温度对活性炭纤维结构的影响。同时应用扫描电镜(SEM)对其表面形貌进行表征,通过N_2吸附-脱附测定其孔结构。结果表明,随着活化温度的升高,活性炭得率逐渐减小,碘吸附值先增大后减小,在浸渍比2.5∶1、预氧化温度200℃、预氧化时间90 min、活化温度为800℃、活化时间60 min的条件下,可以制备出比表面积为1 304 m~2·g~(-1)、总孔容为1.004 cm~3·g~(-1)、得率为31.6%、碘吸附值为1 321 mg·g~(-1)的纤维状活性炭。     

一种污泥活性炭的制备及其在兰炭废水处理中的应用

以城市生活污水厂脱水污泥和木屑的混合物为原料,利用ZnCl_2为活化剂制备污泥活性炭。研究了活化温度、活化时间、固液比和活化剂浓度对吸附性能的影响。在活化温度为650℃、活化时间30 min、固液比1∶1.5、活化剂浓度为5 mol·L~(-1)的最佳工艺条件下,制备得到的活性炭碘吸附值为584.85 mg·g~(-1),利用扫描电镜可以观察到其发达的孔隙结构。将制备的污泥活性炭应用于兰炭废水处理中,结果表明,污泥活性炭的投加量为180 g·L~(-1),pH为7,吸附时间60min,挥发酚和氨氮的去除率分别为73.38%和48.27%,废水中污染物浓度明显降低。     

污泥活性炭的制备及其对酸性红G的吸附行为

以城市污水处理厂的脱水污泥为原料,用Zn Cl2活化法制备污泥活性炭,并研究其对水中酸性红G的吸附、脱附行为。选取活化剂浓度、固液比、活化温度及活化时间等因素,通过正交实验确定了最佳工艺,即Zn Cl2浓度30%,固液比1∶2,碳化温度500℃,碳化时间1.5 h。吸附实验结果表明,该污泥活性炭对水中酸性红G的吸附量随着温度升高而增加,在15、25和35℃条件下的最大吸附量分别为153.6、165.6和180.4 mg/g,且吸附等温线能较好用Langmuir方程进行模拟。酸性红G在污泥活性炭上的吸附动力学符合准二级反应动力学模型。污泥活性炭对酸性红G的吸附量随着溶液p H的增大而减小,污泥活性炭的最佳投加量为0.26 g/L。吸附饱和的污泥活性炭可通过碱处理和热处理方法进行脱附,脱附后的吸附剂对酸性红G仍具有很强吸附性能。     

热解气活化的活性炭对水体中甲萘威的吸附性能

以生物质混合压缩颗粒为原料,在600~900℃活化温度下,循环利用热解气制备活性炭,考察热解气的活化作用及活性炭对农药甲萘威的吸附性能。结果表明:热解气具有明显的活化作用,经过活化的炭与热解炭相比孔结构更加发达,表面更加粗糙;活化温度对活性炭理化性质具有显著影响,随温度升高,活性炭芳香性升高,极性降低,含氧官能团逐渐减少,比表面积由239.00 m~2·g~(-1)增加到629.20 m~2·g~(-1),平均孔径由5.438 nm减小至3.005 nm;Freundlich模型能够很好地拟合活性炭对甲萘威的吸附等温线,随活化温度升高,活性炭吸附能力增大;吸附动力学更符合伪二级反应动力学模型,60 h内基本实现吸附平衡;当活化温度为800℃,单位原料对甲萘威的吸附量最大。     

微波活化对Ca(OH)2孔隙结构及脱氯性能的影响

采用微波炉对一定质量的氢氧化钙样品进行活化，利用压汞仪考察了不同微波活化时间及脱氯反应前后的Ca(OH)2总比孔表面积、分段比表面积和孔径分布的变化，并在脱氯实验台上对脱氯效率进行实际测试。结果表明，微波活化存在一个最佳时间，在此时间内样品比孔表面积增大50%左右，而超过这一时间样品比表面积回复性减小；微波活化主要通过增加3～20 nm孔径段的微孔为样品提供更大比表面积；这些新增加的微孔在脱氯反应过程中被完全利用或消耗； 最佳活化时间下的微波活化使Ca(OH)₂在较低Ca/Cl摩尔比下获得更大脱氯效率，Ca/Cl摩尔比=4.1时，脱氯效率增加了20%。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.