Degradation of fats during thermophilic composting of organic waste.

The degradation of fats during thermophilic composting was investigated by adding lard of four different mixing ratios (0, 33.3, 42.9 and 50% on a dry weight basis) to dog food used as a model substrate for organic waste. The lard added at the mixing ratio of 33.3% did not inhibit the decomposition of organic matter in the dog food, with lard itself beginning decomposition after decay of more easily decomposable organic compounds of the dog food, 84 h from the start of composting. The percentage of lard decomposition reached as high as 29.3% by the end of 8 days of composting. By contrast, the decomposition of organic matter in the processed dog food was apparently inhibited when the portion of lard was greater than 33.3%, especially at the earliest stage of composting. It is possible, however, that lard would decompose vigorously once decomposition has begun, even when the ratio of lard is as high as 50%. The percentages of lard decomposition in composting mixtures with 42.9 and 50% lard were 15.7 and 9.50%, respectively, thus the higher the mixing ratio of lard, the lower the percentage of lard decomposition. However, it was found that the maximum decomposition rate of the lard was similar for all of the ratios tested; that is, approximately 5.0 x 10(-3) g carbon h(-1).     

Greenhouse gas emissions from home composting of organic household waste

The emission of greenhouse gases (GHGs) is a potential environmental disadvantage of home composting. Because of a lack of reliable GHG emission data, a comprehensive experimental home composting system was set up. The system consisted of six composting units, and a static flux chamber method was used to measure and quantify the GHG emissions for one year composting of organic household waste (OHW). The average OHW input in the six composting units was 2.6–3.5 kg week^?1 and the temperature inside the composting units was in all cases only a few degrees (2–10 °C) higher than the ambient temperature. The emissions of methane (CH₄) and nitrous oxide (N₂O) were quantified as 0.4–4.2 kg CH₄ Mg^?1 input wet waste (ww) and 0.30–0.55 kg N₂O Mg^?1 ww, depending on the mixing frequency. This corresponds to emission factors (EFs) (including only CH₄ and N₂O emissions) of 100–239 kg CO₂-eq. Mg^?1 ww. Composting units exposed to weekly mixing had the highest EFs, whereas the units with no mixing during the entire year had the lowest emissions. In addition to the higher emission from the frequently mixed units, there was also an instant release of CH₄ during mixing which was estimated to 8–12% of the total CH₄ emissions. Experiments with higher loads of OHW (up to 20 kg every fortnight) entailed a higher emission and significantly increased overall EFs (in kg substance per Mg^?1 ww). However, the temperature development did not change significantly. The GHG emissions (in kg CO₂-eq. Mg^?1 ww) from home composting of OHW were found to be in the same order of magnitude as for centralised composting plants.     

Microbial succession associated with organic matter decomposition during thermophilic composting of organic waste.

Using dog food as a model of the organic waste, thermophilic composting was carried out for 14 days at a fixed temperature of 60 degrees C. The relationship between organic matter decomposition measured by CO2 evolution during the bio-stabilization process and microbial succession expressed as the changes over time in the restriction fragment length polymorphism (RFLP) patterns of 16S rDNA sequences, of micro-organisms associated with the composting material was also examined. The CO2 evolution rate peaked on day 3 and gradually decreased until it became extremely small after day 9 of composting, indicating that vigorous organic matter decomposition ceased around this time. On the other hand, the RFLP pattern changed drastically from day 0 to day 4 or 5, then remained stable until day 7 or 8, reaching its final configuration, with little variations, after day 9 of composting. RFLP analysis therefore indicates that microbial succession continued into the later stage of composting. Nevertheless, by day 9, the rate of organic matter decomposition was so low that its influence on microbial populations could be hardly recognized by conventional methods of dilution plating. Moreover, the compost produced by day 9 showed no inhibitory effect on the growth of Komatsuna (Brassica campestris L. var. rapiferafroug), indicating that the maturity of compost is sufficient for plant growth when the rate of organic matter decomposition has become extremely low and the RFLP patterns become stable.     

Mass balances and life cycle inventory of home composting of organic waste

A comprehensive experimental setup with six single-family home composting units was monitored during 1 year. The composting units were fed with 2.6-3.5 kg organic household waste (OHW) per unit per week. All relevant consumptions and emissions of environmental relevance were addressed and a full life-cycle inventory (LCI) was established for the six home composting units. No water, electricity or fuel was used during composting, so the major environmental burdens were gaseous emissions to air and emissions via leachate. The loss of carbon (C) during composting was 63-77% in the six composting units. The carbon dioxide (CO(2)) and methane (CH(4)) emissions made up 51-95% and 0.3-3.9% respectively of the lost C. The total loss of nitrogen (N) during composting was 51-68% and the nitrous oxide (N(2)O) made up 2.8-6.3% of this loss. The NH(3) losses were very uncertain but small. The amount of leachate was 130 L Mg(-1) wet waste (ww) and the composition was similar to other leachate compositions from home composting (and centralised composting) reported in literature. The loss of heavy metals via leachate was negligible and the loss of C and N via leachate was very low (0.3-0.6% of the total loss of C and 1.3-3.0% of the total emitted N). Also the compost composition was within the typical ranges reported previously for home composting. The level of heavy metals in the compost produced was below all threshold values and the compost was thus suitable for use in private gardens.     

Environmental impact of organic fraction of municipal solid waste treatment by composting in Sri Lanka

Journal of Material Cycles and Waste Management - In Sri Lanka, the management of the organic fraction of municipal solid waste (OFMSW) is a challenge. Composting is an environmentally and...     

A kinetic analysis of solid waste composting at optimal conditions

This discussion explores the possibility of having a measure of the biodegradable organic carbon content in solid wastes. Currently, indirect measures for determining the concentration of biodegradable organic matter are being used and most of them are based on respiration indices (oxygen consumption or carbon dioxide production) or chemical parameters (volatile solids or total organic carbon). The results obtained for the cumulative carbon dioxide production in composting experiments can be expressed as "aerobic biodegradable carbon" for the wastes that were studied. The calculation of a useful biodegradable C/N can also be obtained from the aerobic biodegradable carbon content. A comparison with some results obtained in measuring the concentration of "anaerobic biodegradable carbon" also is presented.     

A kinetic analysis of solid waste composting at optimal conditions

Six municipal solid waste (MSW) and yard waste components (food waste, mixed paper, yard waste, leaves, branches, grass clippings) were aerobically decomposed to measure the extent of decomposition under near optimal conditions. Decomposition was characterized by at least two principal stages, for most components, as was indicated by the carbon dioxide production rates. An aerobic biodegradation conceptual model is presented here based on the principle that solids hydrolysis is the rate-limiting step during solid waste composting. The mineralizable solid carbon of each solid waste component was assumed to comprise the readily, the moderately and the slowly (or refractory) hydrolysable carbons, each hydrolyzing at different rates to aqueous (water soluble) carbon. Aqueous carbon mineralizes to CO2 at rapid rates that are not rate-limiting to the process. Solids hydrolysis rate constants were calculated after fitting the experimentally determined carbon dioxide production rate data to model results. Hydrolysis rates for the readily hydrolysable carbon in all components ranged from approximately 0.06 to 0.1 d(-1); hydrolysis rates for the moderately hydrolysable carbon ranged from 0.005 to 0.06 d(-1). Leaves, branches and grass clippings did not have a readily hydrolysable carbon fraction, whilst the leaves and branches had the largest slowly hydrolysable carbon fractions (70%, 82%, respectively, of the total solid organic carbon). Grass and yard waste did not contain slowly hydrolysable carbon fractions. Food waste had the largest readily hydrolysable carbon fraction and produced the highest amount of CO2 among all substrates. Moderately hydrolysable solid carbon fractions ranged from 16% to 90% of the total solid organic carbon for all substrates used.     

Cost effective waste management through composting in Africa

Greenhouse gas (GHG) emissions per person from urban waste management activities are greater in sub-Saharan African countries than in other developing countries, and are increasing as the population becomes more urbanised. Waste from urban areas across Africa is essentially dumped on the ground and there is little control over the resulting gas emissions. The clean development mechanism (CDM), from the 1997 Kyoto Protocol has been the vehicle to initiate projects to control GHG emissions in Africa. However, very few of these projects have been implemented and properly registered. A much more efficient and cost effective way to control GHG emissions from waste is to stabilise the waste via composting and to use the composted material as a soil improver/organic fertiliser or as a component of growing media. Compost can be produced by open windrow or in-vessel composting plants. This paper shows that passively aerated open windrows constitute an appropriate low-cost option for African countries. However, to provide an usable compost material it is recommended that waste is processed through a materials recovery facility (MRF) before being composted. The paper demonstrates that material and biological treatment (MBT) are viable in Africa where they are funded, e.g. CDM. However, they are unlikely to be instigated unless there is a replacement to the Kyoto Protocol, which ceases for Registration in December 2012.     

Performance of compostable baby used diapers in the composting process with the organic fraction of municipal solid waste

In modern societies, disposable diapers constitute a significant percentage of municipal solid wastes. They have been traditionally landfilled or incinerated as only limited recycling processes are being implemented in some parts of Europe. With the implementation of separated collection systems for the organic fraction of municipal solid wastes (OFMSWs) and the need to preserve the environment, compostable diapers have appeared in the market to avoid the main environmental impacts associated to non-biodegradable disposable diapers. In this study, a full-scale composting of door-to-door collected OFMSW with a 3% (w/w) of compostable diapers has also been carried out. Previously, lab-scale experiments confirmed that almost 50% of carbon of compostable diapers is emitted as CO₂ under aerobic controlled conditions. The results obtained at full-scale demonstrate that both the composting process and the final end product (compost) are not altered by the presence of compostable diapers in crucial aspects such as pathogenic content, stability and elemental composition (including nutrients and heavy metals). The main conclusion of this study is that the collection of the OFMSW with compostable diapers can be a new way to transform this waste into high-quality compost.     

Proposal for the integration of decentralised composting of the organic fraction of municipal solid waste into the waste management system of Cuba

Municipal solid waste (MSW) generation and management in Cuba was studied with a view to integrating composting of the organic fractions of MSW into the system. Composting is already included as part of the environmental strategy of the country as an appropriate waste management solution. However, no programme for area-wide implementation yet exists. The evaluation of studies carried out by some Cuban and international organisations showed that organic matter comprises approximately 60-70% of the MSW, with households being the main source. If all organic waste fractions were considered, the theoretical amount of organic waste produced would be approximately 1 Mio. Mg/a, leading to the production of approximately 0.5 Mio. Mg/a of compost. Composting could, therefore, be a suitable solution for treating the organic waste fractions of the MSW. Composting would best be carried out in decentralised systems, since transportation is a problem in Cuba. Furthermore, low technology and low budget composting options should be considered due to the problematic local economic situation. The location for such decentralised composting units would optimally be located at urban agricultural farms, which can be found all over Cuba. These farms are a unique model for sustainable farming in the world, and have a high demand for organic fertiliser. In this paper, options for the collection and impurity-separation in urban areas are discussed, and a stepwise introduction of source-separation, starting with hotel and restaurant waste, is suggested. For rural areas, the implementation of home composting is recommended.     

A novel sustainable decision making model for municipal solid waste management

This paper reviews several models developed to support decision making in municipal solid waste management (MSWM). The concepts underlying sustainable MSWM models can be divided into two categories: one incorporates social factors into decision making methods, and the other includes public participation in the decision-making process. The public is only apprised or takes part in discussion, and has little effect on decision making in most research efforts. Few studies have considered public participation in the decision-making process, and the methods have sought to strike a compromise between concerned criteria, not between stakeholders. However, the source of the conflict arises from the stakeholders' complex web of value. Such conflict affects the feasibility of implementing any decision. The purpose of this study is to develop a sustainable decision making model for MSWM to overcome these shortcomings. The proposed model combines multicriteria decision making (MCDM) and a consensus analysis model (CAM). The CAM is built up to aid in decision-making when MCDM methods are utilized and, subsequently, a novel sustainable decision making model for MSWM is developed. The main feature of CAM is the assessment of the degree of consensus between stakeholders for particular alternatives. A case study for food waste management in Taiwan is presented to demonstrate the practicality of this model.     

Biodegradation of paper waste under controlled composting conditions

The presence of paper in municipal solid waste (MSW) interferes with the efficiency of composting plants. The compost feedstock to these plants is between 12% and 27% paper on a dry weight basis, with an initial C:N ratio ranging from 32:1 to 57:1. Tests of the last aerobic biodegradability (LAB) of the type of paper present in paper and cardboard packaging were carried out, following UNE-EN 14046 standards. The results obtained, measured through the quantity of CO₂ generated over 45 days, compared with the maximum that could be produced (ThCO₂), showed that the presence of paper retards, to a great degree, the biodegradation of organic material in general. Specifically, the presence of papers with a degradation D (%) >60% at 45 days (white (W) and recycled paper (R)) could be allowed, but always in proportions that did not exceed 27% in dry weight. These results can be achieved with an industrial level process, pre-treated by trituration.     

Mass and element balance in food waste composting facilities

The mass and element balance in municipal solid waste composting facilities that handle food waste was studied. Material samples from the facilities were analyzed for moisture, ash, carbon, nitrogen, and the oxygen consumption of compost and bulking material was determined.Three different processes were used in the food waste composting facilities: standard in-vessel composting, drying, and stand-alone composting machine. Satisfactory results were obtained for the input/output ash balance despite several assumptions made concerning the quantities involved. The carbon/nitrogen ratio and oxygen consumption values for compost derived only from food waste were estimated by excluding the contribution of the bulking material remaining in the compost product. These estimates seemed to be suitable indices for the biological stability of compost because there was a good correlation between them, and because the values seemed logical given the operating conditions at the facilities.     

Comparison of mass balance, energy consumption and cost of composting facilities for different types of organic waste

Mass balance, energy consumption and cost are basic pieces of information necessary for selecting a waste management technology. In this study, composting facilities that treat different types of organic waste were studied by questionnaire survey and via a chemical analysis of material collected at the facilities.The mass balance was calculated on a dry weight basis because the moisture content of organic waste was very high. Even though the ratio of bulking material to total input varied in the range 0-65% on a dry basis, the carbon and ash content, carbon/nitrogen ratio, heavy metal content and inorganic nutrients in the compost were clearly influenced by the different characteristics of the input waste. The use of bulking material was not correlated with ash or elemental content in the compost. The operating costs were categorised into two groups. There was some economy of scale for wages and maintenance cost, but the costs for electricity and fuel were proportional to the amount of waste. Differences in operating costs can be explained by differences in the process characteristics.     

Effectiveness of three bulking agents for food waste composting

Rather than landfilling, composting the organic fraction of municipal solid wastes recycles the waste as a safe and nutrient enriched soil amendment, reduces emissions of greenhouse gases and generates less leachate. The objective of this project was to investigate the composting effectiveness of three bulking agents, namely chopped wheat (Triticum) straw, chopped mature hay consisting of 80% timothy (milium) and 20% clover (triphullum) and pine (pinus) wood shavings. These bulking agents were each mixed in duplicates at three different ratios with food waste (FW) and composted for 10 days using prototype in-vessel composters to observe their temperature and pH trends. Then, each mixture was matured in vertical barrels for 56 days to measure their mass loss and final nutrient content and to visually evaluate their level of decomposition. Chopped wheat straw (CWS) and chopped hay (CH) were the only two formulas that reached thermophilic temperatures during the 10 days of active composting when mixed with FW at a wet mass ratio of 8.9 and 8.6:1 (FW:CWS and FW:CH), respectively. After 56 days of maturation, these two formulas were well decomposed with no or very few recognizable substrate particles, and offered a final TN exceeding the original. Wood shavings (WS) produced the least decomposed compost at maturation, with wood particles still visible in the final product, and with a TN lower than the initial. Nevertheless, all bulking agents produced compost with an organic matter, TN, TP and TK content suitable for use as soil amendment.     

Characterization of food waste and bulking agents for composting

The characterization of food waste (FW) and locally available bulking agents (BA) are a prerequisite to optimizing compost recipes. This study measured the variation in FW characteristics (pH, dry matter (DM), carbon (C), wet bulk density and Total Kjeldahl Nitrogen (TKN)) produced by a restaurant and a community kitchen in downtown Montreal, Canada from May to August 2004. The project also measured the mass of FW produced by another restaurant and a group of 20-48 households, from June to August 2004. Locally available BA (hay, straw, pine wood shavings, cardboard, left over cattle feed and wheat residue pellets) were also characterized to formulate composting recipes based on the FW characteristics observed during a period representative of winter and summer conditions. Residential and restaurant FW characteristics varied significantly over the summer months, although the mass produced remained constant at 0.61 and 0.56 kg capita(-1)day(-1), respectively. In addition, the number of customers served by the restaurant increased by nearly 50% from June to August. The BA with the highest moisture adsorption capacity was found to be the wheat residue pellets, followed by chopped straw. Wheat residue pellets, chopped hay and left over cattle feed all presented a balanced C/N ratio. Wheat residue pellets and wheat straw, chopped hay and cardboard demonstrated neutral pH values. Based on the variable FW characteristics and monthly production rates, the formulation of recipes indicates that compost facilities must be flexible enough to handle seasonal variations of as much as 50% by volume.     

Modeling of substrate degradation and oxygen consumption in waste composting processes

A multi-component modeling system was developed to simulate substrate degradation and oxygen consumption in waste composting processes. Levels of soluble substrate (Ss), insoluble substrate (Si), active biomass (X), inert material, moisture, temperature, and oxygen concentration were considered as state variables. The relationships among these variables were also incorporated within the modeling framework. Three conversion reactions, including growth of aerobic biomass, decay of aerobic biomass, and solubilisation of insoluble substrate, were considered in the simulation system. The modeling inputs included temperature, moisture, oxygen concentration, and initial conditions of the state variables, while the outputs included oxygen uptake accumulation (OUA), oxygen uptake rate (OUR), Ss, Si, and X for representing the substrate degradation and oxygen consumption status. The effectiveness of the developed model was demonstrated through its application to a case study in a 30L vessel over 200h. Through verification-based composting experiments, it was shown that the modeling solutions were consistent with the experimental results with an acceptable accuracy level. Sensitivity analyses of the model showed that an increased maximum microbial growth rate would result in raised OUA, OUR, Ss, and X levels; a decreased biomass decay rate constant would help enhance the composting process. Moreover, variations in the maximum growth rate would affect the composting process more significantly than those of the biomass decay rate constant.     

Effect of C/N ratio on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco

The goal of this research was to investigate the effect of the C/N ratio on the in-vessel composting, under air pressure, of organic fraction of municipal solid waste in Morocco. Firstly, an in-vessel bioreactor was designed and used to evaluate the appropriate initial pressure for the composting process. Secondly, five bioreactors were run with C/N ratios of 26 (control; no C supplement), 32.2, 38.4, 44.6, and 50.8. Parameters monitored included internal air pressure, C/N ratio, temperature, volatile solids reduction, and maturity of the obtained composts. The relative microbial activity was observed indirectly using volatile solids removal and the relative heat generation data. The experimental results showed that organic waste could be composted within 10?days and the operating initial parameters that converted the most volatile solids and carbons in the feedstock were as follows: 0.6?×?10⁵ Pa for the initial air pressure and 26 for the C/N ratio. Maturity tests, in optimal conditions, showed that the final compost has characteristics of stable compost and can be used as a soil conditioner. In addition, compost obtained from the experiment that considered a C/N ratio of 32.2 showed good maturity levels and may also be used for agricultural applications.     

Home composting as an alternative treatment option for organic household waste in Denmark: An environmental assessment using life cycle assessment-modelling

An environmental assessment of the management of organic household waste (OHW) was performed from a life cycle perspective by means of the waste-life cycle assessment (LCA) model EASEWASTE. The focus was on home composting of OHW in Denmark and six different home composting units (with different input and different mixing frequencies) were modelled. In addition, incineration and landfilling was modelled as alternatives to home composting. The most important processes contributing to the environmental impact of home composting were identified as greenhouse gas (GHG) emissions (load) and the avoided emissions in relation to the substitution of fertiliser and peat when compost was used in hobby gardening (saving). The replacement of fertiliser and peat was also identified as one of the most sensible parameters, which could potentially have a significant environmental benefit. Many of the impact categories (especially human toxicity via water (HTw) and soil (HTs)) were affected by the heavy metal contents of the incoming OHW. The concentrations of heavy metals in the compost were below the threshold values for compost used on land and were thus not considered to constitute a problem. The GHG emissions were, on the other hand, dependent on the management of the composting units. The frequently mixed composting units had the highest GHG emissions. The environmental profiles of the home composting scenarios were in the order of −2 to 16 milli person equivalents (mPE) Mg⁻¹ wet waste (ww) for the non-toxic categories and −0.9 to 28 mPE Mg⁻¹ ww for the toxic categories. Home composting performed better than or as good as incineration and landfilling in several of the potential impact categories. One exception was the global warming (GW) category, in which incineration performed better due to the substitution of heat and electricity based on fossil fuels.