硝酸镧改性聚丙烯酸对水中氟离子的吸附试验探讨

以丙烯酸为原料,乙二醇二甲基丙烯酸酯为交联剂制得聚丙烯酸树脂(PAA),用于制备表面粗糙、介孔丰富的镧(Ⅲ)改性聚丙烯酸复合树脂(La-PAA)。试验表明,当500 mg/L氟离子溶液pH值为5、吸附时间为300 min时,La-PAA对氟离子的去除率在90%以上。Langmuir方程能较好地拟合氟离子在La-PAA上的吸附等温线,最大吸附量为159.24 mg/g,吸附动力学过程符合准二级动力学方程。     

Chromium speciation in groundwater of a tannery polluted area of Chennai City, India

Chromium speciation in groundwater of a tannery polluted area was investigated for the distribution of chromium species and the influence of redox couples such as Fe(III)/Fe(II) and Mn(IV)/Mn(II). Speciation analysis was carried out by ammonium pyrolidinedithiocarbamate (APDC)–methylisobutylketone (MIBK) procedure. The groundwater samples were analyzed for Cr(III), Cr(VI), and Cr(III)-organic complexes. The APDC could not extract the Cr(III)-organic complexes, but HNO₃ digestion of the groundwater samples released the Cr(III)-organic complexes. The groundwater of the area is relatively oxidizing with redox potential (E _h) and dissolved oxygen (DO) ranged between 65 and 299 mV and 0.25 and 4.65 mg L^???1, respectively. The Fe(II) reduction of Cr(VI) was observed in some wells, but several wells that had Fe(II)/Cr(VI) concentrations more than the stoichiometric ratio (3:1) of the reduction reaction also had appreciable concentration of Cr(VI). This could partly be due to the oxidation of Fe(II) to Fe(III) by DO. It appears that the occurrence of Mn more than the Fe(II) concentration was also responsible for the presence of Cr(VI). Other reasons could be the Fe(II) complexation by organic ligands and the loss of reducing capacity of Fe(II) due to aquifer materials, but could not be established in this study.     

Chromium (VI) biosorption properties of multiple resistant bacteria isolated from industrial sewerage

Chromium (VI) [Cr (VI)] biosorption by four resistant autochthonous bacterial strains was investigated to determine their potential for use in sustainable marine water-pollution control. Maximum exchange between Cr (VI) ions and protons on the cells surfaces were at 30–35 °C, pH?2.0 and 350–450 mg/L. The bacterial strains effectively removed 79.0–90.5 % Cr (VI) ions from solution. Furthermore, 85.3–93.0 % of Cr (VI) ions were regenerated from the biomasses, and 83.4–91.7 % of the metal was adsorbed when the biomasses was reused. Langmuir isotherm performed better than Freundlich isotherm, depicting that Cr (VI) affinity was in the sequence Rhodococcus sp. AL03Ni?>?Burkholderia cepacia AL96Co?>?Corynebacterium kutscheri FL108Hg?>?Pseudomonas aeruginosa CA207Ni. Biosorption isotherms confirmed that Rhodococcus sp. AL03Ni was a better biosorbent with a maximum uptake of 107.46 mg of Cr (VI) per g (dry weight) of biomass. The results highlight the high potential of the organisms for bacteria-based detoxification of Cr (VI) via biosorption.     

A novel wet-scrubbing process using Fe(VI) for simultaneous removal of SO2 and NO

The objective of this work was to develop a novel wet-scrubbing process using Fe(VI) for the simultaneous removal of gaseous NO and SO(2). The oxidation of SO(2) and NO with Fe(VI) was studied in aqueous solution at alkaline pH (9.0-11.0). A stoichiometric molar ratio for NO and SO(2) oxidation with Fe(VI) was determined to be nearly 3.0. Sulfate and nitrate was identified as final products by ion chromatography from the reaction at pH 9.0-11.0. The feasibility of simultaneous removal of multiple gas pollutants with the continuous feeding of ferrate in lab-scale was investigated from the view of industrial application. It was found that the removal efficiency of NO and SO(2) was enhanced with the increase of Fe(VI) concentration, more than 90% NO removal efficiency and 100% SO(2) removal efficiency were achieved by wet-scrubbing process using Fe(VI) at room temperature and ambient atmosphere. The results demonstrate that Fe(VI) could be an effective wet-scrubbing agent for the simultaneous removal of NO and SO(2).     

A study on hexachromic ion selective electrode based on supported liquid membranes

An ion selective electrode (ISE) for determining Cr(VI) using supported liquid membranes (SLMs) containing trioctylphosphine oxide (TOPO) was investigated in this study. TOPO, as a carrier, had a high selectivity for Cr(VI) against interfering ions such as sulfate, nitrate, nitrite, and chloride. The composition of the SLM was optimized as 0.193 g TOPO/1 mL NPOE (o-nitrophenyl octyl ether)/0.5 g poly (vinyl chloride) for detection of Cr(VI). The Cr(VI) concentration was measured in the range of1 × 10^-3 to 1 × 10^-6 M with the SLM prepared in the study. It seemed that Cr(VI) was transported in the SLM as a triply charged ion indicated by the slope of the emf response. Selectivity coefficients and detection limits of Cr(VI) in the presence of interfering ions were determined experimentally using the fixed interference method.     

Geochemical assessment of metal transport in glacial till during electrokinetic remediation

This paper presents the chemical speciation and retention behavior of chromium (Cr), nickel (Ni), and cadmium (Cd) prior to and after the electrokinetic remediation in glacial till soil. The speciation of the metals was predicted using the chemical speciation program MINEQL⁺. The simulations were performed for single-contaminant with only Cr(VI) or Ni, and multi-contaminants consisting of: (1) Cr(VI), Ni, and Cd; (2) Cr(III), Ni and Cd; (3) Cr(VI), Cr(III), Ni and Cd; (4) Cr(VI), Ni, and Cd with reducing agents; and (5) Cr(III), Ni, and Cd with oxidizing agent (Mn). The results showed that the speciation and distribution of cationic metals [Ni, Cd, and Cr(III)] in glacial till soil remain unaffected or slightly affected during electrokinetics. This is attributed to the high pH buffering capacity of the glacial till, leading the metals to precipitate in the soil prior to and after electrokinetics. This study showed that during electrokinetics, Cr(VI) existed as anionic complex and migrated towards the anode and the migration is maximum in case of a single-contaminant system. The study also showed that near the anode in the absence of any reducing and oxidizing agent, Cr(VI) mostly adsorbed, and some of Cr(VI) reduced to Cr(III) and migrated towards the cathode and finally precipitated due to high pH conditions. Ni and Cd remain adsorbed or precipitated due to the high pH conditions throughout the soil. Among the reducing agents, the sulfide had significant effect on the migration of metals compared to ferrous ions. While in the presence of oxidizing agent (Mn), no noticeable Cr(VI) was found in the soil sample indicating the reduction of Cr(VI) to Cr(III) and the predominance of reducing conditions due to the presence of naturally occurring iron in the glacial till soil. Overall, this study provides a reasonable explanation of the speciation and distribution of chromium, nickel and cadmium during the electrokinetic remediation of glacial till soil.     

Effect of pH,ionic strength,and background electrolytes on Cr(VI) and total chromium removal by acorn shell of Quercus crassipes Humb. & Bonpl.

The ability of Quercus crassipes acorn shells (QCS) to remove Cr(VI) and total chromium from aqueous solutions was investigated as a function of the solution pH, ionic strength, and background electrolytes. It was found that Cr(VI) and total chromium removal by QCS depended strongly on the pH of the solution. Cr(VI) removal rate increased as the solution pH decreased. The optimum pH for total chromium removal varied depending on contact time. NaCl ionic strengths lower than 200 mM did not affect chromium removal. The presence of 20 mM monovalent cations and anions, and of divalent cations, slightly decreased the removal of Cr(VI) and total chromium by QCS; in contrast, divalent anions (SO₄ ^2?, PO₄ ^2?, CO₃ ^2?) significantly affected the removal of Cr(VI) and total chromium. The biosorption kinetics of chromium ions followed the pseudo-second-order model at all solution pH levels, NaCl ionic strengths and background electrolytes tested. Results suggest that QCS may be a potential low-cost biosorbent for the removal of Cr(VI) and total chromium from aqueous solutions containing various impurities.     

Accumulation of heavy metals in Spinacia oleracea irrigated with paper mill effluent and sewage

The present study on heavy metal contamination in soil and their accumulation in edible part (leaves) and roots of Spinacia oleracea (Spinach) on irrigation with paper mill effluent (PME)/sewage revealed that there was significant increase in the nickel (Ni, +227.17 %) content of the soil irrigated with PME, whereas in the soil irrigated with sewage chromium (Cr, +274.84 %), iron (Fe, +149.56 %), and cadmium (Cd, +133.39 %), contents were increased appreciably. The value of enrichment factor (EF) for Ni (3.27) indicated moderate enrichment in PME-irrigated soil. The EF of Fe, zinc (Zn), Cd, and Cr were <2 in PME effluent-irrigated soil which showed deficiency of minimal enrichment. In sewage irrigated soil, EF value for Cr, Fe, and Cd indicated moderate enrichment, while the values for Zn and Ni indicated deficiency of minimal enrichment. Among various metallic concentrations, the maximum concentration of Fe was observed in leaves (400.12?±?11.47 mg/kg) and root (301.41?±?13.14 mg/kg) of S. oleracea after irrigation with PME, whereas the maximum concentrations of Fe was found in leaves (400.49?±?5.97 mg/kg) and root (363.94?±?11.37 mg/kg) of S. oleracea after irrigation with sewage for 60 days. The bioaccumulation factor value was found maximum for Cd (2.23) in the plants irrigated with PME while that of Fe (0.90) in the plants irrigated with sewage. The undiluted use of PME/sewage for irrigation increased the concentration of Cr, Cd, Zn, Ni, and Fe metals which were accumulated in S. oleracea, posing a potential threat to human health from this practice of irrigation.     

Environmental Impacts of Dispersed Development from Federal Infrastructure Projects

An ion selective electrode (ISE) for the measurement of Cr(VI), using supported liquid membranes (SLMs), containing tricaprylmethyl ammonium chloride (Aliquat336), was investigated in this study. Aliquat336, as a carrier, had a high selectivity for Cr(VI) in the presence of interfering ions, in the order SO4(2-) > CO3(2-) > Cl(-) > NO2(-) > NO3(-) > I(-) > SCN(-). The composition of the SLM for the detection of Cr(VI) was optimized at 0.169 mL Aliquat336 mL(-1) NPOE (o-nitrophenyl octyl ether) 0.5 g Poly (vinyl chloride), for the preparation of a 19.6 cm2 sheet. The Cr(VI) concentrations were measured, using the SLM prepared in the study, in the range 2.023 x 10(-5) to 0.1 M (1.052 to 5200 ppm). It seemed that the Cr(VI) was transported as a negatively charged monovalent ion, as indicated by the slope of the electromotive force (emt) response. The selectivity coefficients and detection limits for the Cr(VI). against the interfering ions, were determined experimentally using the fixed interference (FIM) and the separate solution methods (SSM).     

Characterisation of particulate matter emissions from the Zimbabwe Mining and Smelting Company (ZIMASCO) Kwekwe Division (Zimbabwe): a ferrochrome smelter

Particulate matter emissions from stack number 2 of a majorferrochrome smelter, Zimbabwe Mining and Smelting Company(ZIMASCO) were characterized and the rates at which the elementsCr, Fe, Cu and Zn and total ferrochrome dust are emitted into theatmosphere were determined. The extent of soil contamination bythe dust deposited around the smelter in the generally prevailingsoutheasterly wind direction around the smelter was carried out.The highest concentrations of Cr and Fe occurred in the fineparticulates of sizes less than 59 m whilst that of Cu and Znoccurred in the coarse particulates of size range 70-100 m.The emission rates from stack 2 were; total ferrochromeparticulates 62.17 kg h^-1, Cr 6.217 kg h^-1, Fe 2.423 kg h^-1, Zn42 mg h^-1 and 6 mg h^-1 for Cu. Particulate matter was emitted at arate of 289 mg m^-3 from stack number 2. This value exceeds thelegal limit of 200 mg m^-3. Chromium and iron are the metalsin the largest amounts. The particles that constitute the largestproportion of the dust were in the range of 58-107.5 m. Thisis a characteristic feature of the particulate matter emissionsfrom ZIMASCO. Soils in the downwind direction from the smelterwere polluted with Cr up to a distance of about 700 m outward fromthe perimeter of the boundary of the smelter.     

Nitrate and ammonium ions removal from groundwater by a hybrid system of zero-valent iron combined with adsorbents

Nitrate (NO(3)(-)) is a commonly found contaminant in groundwater and surface water. It has created a major water quality problem worldwide. The laboratory batch experiments were conducted to investigate the feasibility of HCl-treated zero-valent iron (Fe(0)) combined with different adsorbents as hybrid systems for simultaneous removal of nitrate (NO(3)(-)) and ammonium (NH(4)(+)) ions from aqueous solution. The maximum NO(3)(-) removal in combined Fe(0)-granular activated carbon (GAC), Fe(0)-filtralite and Fe(0)-sepiolite systems was 86, 96 and 99%, respectively, at 45 °C for 24 h reaction time. The NO(3)(-) removal rate increased with the increase in initial NO(3)(-) concentration. The NO(3)(-) removal efficiency by hybrid systems was in the order of sepiolite > filtralite > GAC. The NH(4)(+) produced during the denitrification process by Fe(0) was successfully removed by the adsorbents, with the removal efficiency in the order of GAC > sepiolite > filtralite. Results of the present study suggest that the use of a hybrid system could be a promising technology for achieving simultaneous removal of NO(3)(-) and NH(4)(+) ions from aqueous solution.     

Welding fumes from stainless steel gas metal arc processes contain multiple manganese chemical species

Fumes from a group of gas metal arc welding (GMAW) processes used on stainless steel were generated using three different metal transfer modes and four different shield gases. The objective was to identify and measure manganese (Mn) species in the fumes, and identify processes that are minimal generators of Mn species. The robotic welding system was operated in short-circuit (SC) mode (Ar/CO2 and He/Ar), axial spray (AXS) mode (Ar/O2 and Ar/CO2), and pulsed axial-spray (PAXS) mode (Ar/O2). The fumes were analyzed for Mn by a sequential extraction process followed by inductively coupled plasma-atomic emission spectroscopy (ICP-AES) analysis, and by X-ray diffraction (XRD). Total elemental Mn, iron (Fe), chromium (Cr) and nickel (Ni) were separately measured after aqua regia digestion and ICP-AES analysis. Soluble Mn2+, Fe2+, Fe3+, and Ni2+ in a simple biological buffer (phosphate-buffered saline) were determined at pH 7.2 and 5.0 after 2 h incubation at 37 C by ion chromatography. Results indicate that Mn was present in soluble form, acid-soluble form, and acid-soluble form after reduction by hydroxylamine, which represents soluble Mn0 and Mn2+ compounds, other Mn2+ compounds, and (Mn3+ and Mn4+) compounds, respectively. The dominant fraction was the acid-soluble Mn2+ fraction, but results varied with the process and shield gas. Soluble Mn mass percent in the fume ranged from 0.2 to 0.9%, acid-soluble Mn2+ compounds ranged from 2.6 to 9.3%, and acid plus reducing agent-soluble (Mn3+ and Mn4+) compounds ranged from 0.6 to 5.1%. Total Mn composition ranged from 7 to 15%. XRD results showed fumes had a crystalline content of 90-99% Fe3O4, and showed evidence of multiple Mn oxides, but overlaps and weak signals limited identification. Small amounts of the Mn2+ in the fume (<0.01 to ≈ 1% or <0.1 to ≈ 10 microg ml(-1)) and Ni2+ (<0.01 to ≈ 0.2% or <0.1 to ≈ 2 mg ml(-1)) ions were found in biological buffer media, but amounts were highly dependent on pH and the welding process. Mn generation rates for the fractions were tabulated, and the influence of ozone is discussed. The conclusions are that exposures to welding fumes include multiple Mn species, both soluble and insoluble, and that exposures to Mn species vary with specific processes and shield gases.     

Chromium speciation in a contaminated groundwater: redox processes and temporal variability

Chromium species (Cr(III), Cr(VI), and Cr(III)-organic) in groundwater of a tannery contaminated area were monitored during pre- and post-monsoon seasons for a period of 3 years (May 2004 to January 2007). The objectives of the study were (1) to investigate the temporal variation of chromium species and other matrix constituents and (2) to study the redox processes associated with the temporal variation of chromium species. Samples were collected from 15 dug wells and analyzed for chromium species and other constituents. The results showed that the groundwater was relatively more oxidizing during post-monsoon periods than the pre-monsoon periods. Except one sample, the concentration of chromium species were found in the order of Cr(VI)>Cr(III)>Cr(III)-organic complexes during all the pre- and post-monsoon periods. In most of the wells, the concentrations of Cr(III), Cr(VI), and Cr(III)-organic decreased during post-monsoon periods compared to their pre-monsoon concentrations. However, the Cr(VI)/Cr_Total ratio still increased and the Cr(III)/Cr_Total ratio decreased during post-monsoon periods in most of the samples. The possible mechanisms for the temporal variation of chromium species were (1) Fe(II) reduction of Cr(VI) vs oxidation of Fe(II) by dissolved oxygen and (2) oxidation of Cr(III) by Mn(IV).     

西安城北地区秋季PM_(2.5)中的矿尘颗粒污染特征

采用单颗粒气溶胶飞行时间质谱仪(Single Particle Aerosol Mass Spectrometer,SPAMS)对西安市大气矿尘颗粒物进行连续12 d在线分析,共采集到107 425个同时含有正负质谱信息的矿尘颗粒,矿尘颗粒物占PM_(2.5)样本数的8.44%。结果表明,矿尘颗粒物的正离子碎片成分以Na~+、K~+、Al~+、Ca~+、CaO~+、Fe~+为主,同时还含有Pb~+等,负离子碎片成分以NO~-_2和NO~-_3为主,另外还含有HSO~-_4、SiO~-_3、HSiO~-_3、H(NO_3)~-_2等。在西安市大气细颗粒物中,矿尘颗粒物中贡献较大的几类(如含钙、含铁、铁氧颗粒物等)大多是老化的成分。将观测阶段采集到的矿尘颗粒纳入本地污染源谱进行来源分析,其主要来源为扬尘源、工业源、燃煤源和汽车尾气源等。     

Rice seed toxicity tests for organic and inorganic substances

Plant seed toxicity tests can be used to evaluate hazardous waste sites and to assess toxicity of complex effluents and industrial chemicals. Conventional plant seed toxicity tests are performed using culture dishes containing filter paper. Some reports indicate that filter papers might interfere with the toxicity of inorganic substances. In this study, a plastic seed tray was used. Rice was used as the test species.A comparison of results in the literature and this study revealed that variation of test species, methods, exposure duration, and other factors may affect the test results. The results of this study showed that the order of decreasing toxicity of metal ions was Cu>Ag>Ni>Cd>Cr(VI)>Pb>Zn>Mn>NaF for rice. The test results were similar to those reported in the literature for lettuce Ag>Ni>Cd,Cu>Cr(VI)>Zn>Mn, millet Cu,Ni>Cd>Cr(VI)>Zn>Mn, and ryegrass Cu>Ni>Mn>>Pb>Cd>Zn>Al>Hg>Cr>Fe. The order of decreasing toxicity of organic herbicides was paraquat, 2,4-D>>glyphosate>bromacil.     

Oxidation of Cr(III) to Cr(VI) during chlorination of drinking water

Drinking water treatment typically uses strong oxidants such as chlorine which are capable of converting Cr(III) to Cr(VI). The rates and extent of Cr(III) oxidation by chlorine are not well established. Cr(III) oxidation experiments were therefore conducted in distilled deionized water and New York City tap water dosed initially with Cr(III) and supplemented with sodium hypochlorite to increase free chlorine residual. Reaction progress was monitored using capillary electrophoresis which quenched reactions and allowed for quantification of Cr(VI). Three different forms of Cr(III) were used as reactants: a Cr(III) nitrate salt, Cr(III)-EDTA, and Cr(III) hydroxide. Rates of Cr(VI) production for all three forms of Cr(III) were rapid, on the order of hours. However, oxidation rates slowed and a plateau in Cr(VI) concentrations was reached. This resulted in less than 100% conversion of Cr(III) to Cr(VI) even at relatively high chlorine doses (10 to 100 mg L(-1) as Cl(2)). The loss of free chlorine due to a non-Cr chlorine demand, the precipitation of Cr(III) to Cr(OH)(3)(s), and the partial oxidation of Cr(III) to intermediate oxidation states (i.e. Cr(IV) and Cr(V)) were examined and eliminated as possible explanations for this behavior. Consumption of chlorine via reaction with intermediate oxidation states of Cr is therefore offered as a possible explanation for the plateau in Cr(VI) concentrations.     

磁性硅基介孔材料对水中微囊藻毒素的吸附研究

采用水热合成法可控合成了磁性Fe 3O 4@SiO 2和Fe 3O 4@SiO 2@Cu^2+球状核壳介孔材料,研究了模板剂的种类及去除方式对形貌的影响,并将材料用作固相萃取剂选择性吸附水中微囊藻毒素,结合高效液相色谱定量分析来研究其对MC-LR的吸附性能。实验表明,十六烷基三甲基溴化铵(CTAB)模板剂更有利于壳层的形成,3次乙醇振荡萃取的方式对于两种材料均可达到很好的模板剂去除效果,对MC-LR的吸附率分别达到85%和95%以上,而马弗炉煅烧方式则适用于Fe 3O 4@SiO 2@Cu^2+介孔材料的制备。太湖水样中MC-LR的去除实验表明,两种材料能够很好地应用于实际水样处理。     

Flow injection analysis of trace chromium (VI) in drinking water with a liquid waveguide capillary cell and spectrophotometric detection

Hexavalent chromium (Cr(VI)) is an acknowledged hazardous material in drinking waters. As such, effective monitoring and assessment of the risks posed by Cr(VI) are important analytical objectives for both human health and environmental science. However, because of the lack of highly sensitive, rapid, and simple procedures, a relatively limited number of studies have been carried out in this field. Here we report a simple and sensitive analytical procedure of flow injection analysis (FIA) for sub-nanomolar Cr(VI) in drinking water samples with a liquid core waveguide capillary cell (LWCC). The procedure is based on a highly selective reaction between 1, 5-diphenylcarbazide and Cr(VI) under acidic conditions. The optimized experimental parameters included reagent concentrations, injection volume, length of mixing coil, and flow rate. Measurements at 540 nm, and a 650-nm reference wavelength, produced a 0.12-nM detection limit. Relative standard deviations for 1, 2, and 10 nM samples were 5.6, 3.6, and 0.72 % (n?=?9), and the analysis time was <2 min sample^?1. The effects of salinity and interfering ions, especially Fe(III), were evaluated. Using the FIA-LWCC method, different sources of bottled waters and tap waters were examined. The Cr(VI) concentrations of the bottled waters ranged from the detection limit to ～20 nM, and tap waters collected from the same community supply had Cr(VI) concentration around 14 nM.     

Goose barnacle Pollicipes pollicipes as biomonitor of metal contamination in the northwest coast of Portugal

The main objective of this work was to assess the potential use of goose barnacle Pollicipes pollicipes as biomonitor of metal contamination in northwest (NW) coast of Portugal. The concentrations of Cd, Cr, Cu, Fe, Mn, Ni and Zn were determined in coastal seawaters and tissues of P. pollicipes, which allowed establishing correlations between metals in coastal seawaters and P. pollicipes and calculating metal bioaccumulation factors (BAFs). The results of this study showed that P. pollicipes soft tissues can be used for monitoring metal contamination in these coastal seawaters: (1) there were significant correlations (p??0.05); (2) soft tissues were sensitive to spatial variations of metal bioavailabilities and their concentrations ranged 0.70-2.22?mg?Cd?kg(-1), 0.49-1.40?mg?Cr?kg(-1), 1.37-2.07?mg?Ni?kg(-1), 2.4-3.3?mg?Cu?kg(-1), 5-59?mg?Mn?kg(-1), 134-578?mg?Fe?kg(-1)and 728-1,854?mg?Zn?kg(-1); (3) mean logarithmic bioaccumulation factors (log BAF) of Fe, Cd and Zn were higher, 5.57, 5.47 and 4.41, respectively, than mean log BAFs of Cr, Mn, Cu and Ni, 4.18, 4.14, 3.98 and 3.51, respectively. In contrary, P. pollicipes shell plates were not considered ideal material to monitor metal bioavailabilities in these coastal seawaters. Regarding the very high concentrations of Zn obtained in the coastal seawaters and P. pollicipes soft tissues, the NW coast of Portugal should be classified as "Class III/IV - Remarkably/Highly Polluted".     

Chthamalus montagui as biomonitor of metal contamination in the northwest coast of Portugal

The concentrations of seven metals (Cd, Cr, Cu, Fe, Mn, Ni and Zn) were determined in coastal seawaters and soft and hard tissues of the barnacle Chthamalus montagui from the northwest coast of Portugal to assess the potential use of C. montagui as biomonitor of metal contamination. The results of this study showed that C. montagui soft tissues can be used for monitoring metal bioavailabilities in these coastal seawaters: (1) there were significant correlations (p?相似文献