首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
There is strong interest in developing tools to link chemical concentrations of contaminants to the potential for observing sediment toxicity that can be used in initial screening-level sediment quality assessments. This paper presents new approaches for predicting toxicity in sediments, based on 10-day survival tests with marine amphipods, from sediment chemistry, by means of the application of Partial Least Squares-Discriminant Analysis (PLS-DA) and Counter-propagation Artificial Neural Networks (CP-ANNs) to large historical databases of chemical and toxicity data. The exploration of the internal structure of the developed models revealed inherent limitations of predicting toxicity from common chemical analyses of bulk contaminant concentrations. However, the results obtained in the validation of these models combined relevant values of non-error classification rate, sensitivity and specificity of, respectively, 76, 87 and 73% with PLS-DA and 92, 75 and 97% with CP-ANNs, outperforming the results reported for previous approaches.  相似文献   

2.
Recent technical guidance has been published by the European Commission that outlines methodologies for the derivation of Environmental Quality Standards (EQS) in European surface waters under the Water Framework Directive (WFD). The guidance allows the derivation of a long-term EQS from a small dataset. Specifically an EQS can be derived from just three acute data points, although the safety factors built into such an EQS are large (e.g. up to a factor of 1,000). Large safety factors make such EQS uncertain, and often difficult to achieve in practice. We examine dataset requirements for the derivation of EQS and specifically the minimum number of tests needed for setting EQS for long-term chemical exposures that result in reduced relative uncertainty, as assessed simply through the reduction in standard deviation of the means of the values derived. Using ecotoxicity datasets for four example chemicals, for which EQS have been derived in many jurisdictions, we show that variation in the EQS is greatest when using the minimum dataset allowable under the WFD guidance, but decreases rapidly when seven or more datapoints are available. Increasing the minimum number of ecotoxicity data in deriving an EQS results in a greater understanding of ecotoxicological effects. With this knowledge, the mitigating effects of water chemistry can be accounted for in deriving an EQS, even with relatively limited datasets. The new guidance suggests “simplistic” approaches to account for chemical availability, but does not detail how this might be undertaken. We provide examples of ways by which water chemistry effects can be included in deriving implementable EQS for metals with relatively few reliable and relevant data.  相似文献   

3.
The European Union has defined environmental quality standards (EQSs) for surface waters for priority substances and several other pollutants. Furthermore national EQSs for several chemicals are valid in Austria. The study investigated the occurrence of these compounds in municipal wastewater treatment plant (WWTP) effluents. In a first screening of 15 WWTPs relevant substances were identified, which subsequently were monitored in 9 WWTPs over 1 year (every 2 months). Out of 77 substances or groups of substances (including more than 90 substances) 13 were identified as potentially relevant in respect to water pollution and subjected to the monitoring, whereas most other compounds were detected in concentrations far below the respective EQS for surface waters and therefore not further considered. The preselected 13 compounds for monitoring were cadmium (Cd), nickel (Ni), copper (Cu), selenium (Se), zinc (Zn), diuron, polybrominated diphenyl ethers (PBDEs), di(ethyl-hydroxyl)phthalate (DEHP), tributyltin compounds (TBT), nonylphenoles (NP), adsorbable organic halogens (AOX) and the complexing agents ethylenediaminetetraacetic acid (EDTA) as well as nitrilotriacetic acid (NTA). In the effluents of WWTPs the concentrations of the priority substances Cd, NP, TBT and diuron frequently exceeded the respective EQS, whereas the concentrations for DEHP and Ni were below the respective EQS. The effluent concentrations for AOX, EDTA, NTA, Cu, Se and Zn frequently are in the range or above the Austrian EQS for surface waters. Besides diuron and EDTA all compounds are removed at least partially during wastewater treatment and for most substances the removal via the excess sludge is the major removal pathway. For the 13 compounds which were monitored in WWTP effluents population equivalent specific discharges were calculated. Since for many compounds no or only few information is available, these population equivalent specific discharges can be used to assess emissions from municipal WWTPs to surface waters as well as to make a first assessment of the impact of a discharge on surface waters chemical status. Comparing discharges and river pollution on a load basis, the influence of diffuse sources becomes obvious and therefore should also be taken into consideration in river management.  相似文献   

4.
Moraes R  Elfvendahl S  Kylin H  Molander S 《Ambio》2003,32(4):258-263
Pesticide residues in water, sediment, and fish samples from rivers of a Brazilian Rain Forest Reserve were measured in November 1998, March 1999, and January 2000. Concentrations of the individual pesticides were compared to ecotoxicological benchmarks based on acute toxicity tests, and to regulatory guidelines to determine the potential concern for effects on aquatic life and human health. Pesticides and metabolites were detected at all 7 sites surveyed. Residues of a total of 27 pesticides or metabolites were found in water and/or sediment samples and fish have accumulated some of the most persistent of these residues. Measured concentrations in water and sediment indicated concern for preservation of aquatic fauna. Several pesticides in water were above levels for drinking water recommended by Brazilian and/or European Union authorities, indicating also a concern for human health.  相似文献   

5.
The utility of stable isotope tracers for investigating the relationship between cadmium (Cd) partitioning in artificial sediment-water systems and Cd accumulation in a benthic detritivore (Asellus racovitzai, Isopoda) was explored. In the laboratory, Cd isotopes were applied to synthetic sediment and isotope concentrations were measured in sediment, overlying water and exposed asellids over a 10-day period. Isotope ratios measured in sediment and water were compared to ratios measured in asellids to determine whether Cd partitioning could predict metal bioaccumulation. Two different parameters which might affect Cd partitioning between the sediment and overlying water compartments were investigated: the chemical form in which Cd was added to systems, and the organic matter content of the sediment. To test the effect of chemical form on Cd partitioning, three isotopes of cadmium were individually applied to formulated sediment in varying combinations of 113Cd(NO3)2, 112Cd-humic acid (HA) 114CdSO4. The results demonstrated that chemical form did not influence partitioning, as the Cd isotope that was applied to sediment in the nitrate form exhibited similar partitioning between sediment and overlying water as the isotope that was applied in the sulfate or HA form. However, Cd isotope concentrations in overlying water were strongly related to the pattern of isotope accumulation in asellids suggesting that overlying water concentrations determined Cd bioaccumulation. In contrast, when the organic matter content of sediment was increased through the addition of Sphagnum peat moss, total Cd concentrations in overlying water and tissue were low, and there was no relationship between Cd-isotope concentrations in tissue and water. These results indicate that Cd accumulation occurred primarily from water, and factors that increase metal partitioning to sediment, such as increased sediment organic matter content, decrease Cd accumulation in asellids. The stable isotope tracer method described herein appears to be a useful technique for investigating the relationship between metal partitioning and bioaccumulation in simple sediment systems, but could also be extended to more complex systems, and used with different metals that have multiple stable isotopes.  相似文献   

6.
The use of water injection dredging (WID) is increasing in the UK's inland waterways and marinas. Jets of water are injected under low pressure directly into bottom sediment creating a turbulent water-sediment mixture that flows under the influence of gravity. Many of these sediments are highly contaminated and little is known of the effects of contaminant release on water quality or the risk to biota living in both the sediment and the water column. Sediment cores were collected from Limehouse Basin, a proposed WID site in SE England and current sediment toxicity was assessed using a number of techniques. Comparison of metal data to US sediment quality guidelines indicated intermediate levels of toxicity while, calculation of acid volatile sulphide to simultaneously extracted metal ratios underestimated the potential toxicity to sediment dwelling organisms. In contrast, porewater ammonia concentrations were in excess of all published ecotoxicological guidelines and indicate serious risk to biota. Re-suspension experiments were used to mimic the effects of WID on overlying water quality and ecotoxicity tests were carried out on elutriates using Daphnia magna to examine the impacts on biota. Concentrations of a range of metals in the elutriates predict that adverse biological effects would be observed during WID, however only 10% of the elutriate samples caused an adverse effect on Daphnia. Limehouse Basin is a complex aquatic environment receiving predominantly fresh waters while the sediments have high porewater chloride concentrations reminiscent of previous tidal inputs to the basin, making the choice of test organism problematic.  相似文献   

7.
van Beelen P 《Chemosphere》2003,53(8):795-808
The results of microbial toxicity tests are needed for the risk assessment of polluted sediments. In comparison with animals the anaerobic microorganisms are more tolerant to natural sediment conditions whereas they are more sensitive for a number of specific pollutants. Microbial toxicity tests from a literature search were classified in seven categories. Category A, B and C use polluted sediments and are applied for sediment monitoring. In category D, a pure chemical is added and the organisms and the test conditions were derived from sediment. Therefore this category can be used for setting sediment quality guidelines which protect sediment functions for the toxic effects of chemicals. In category E, organisms from a polluted site are separated from the sediment and are tested with pure chemicals. Organisms from a more polluted site can be more tolerant to a local pollutant. This is called pollution-induced community tolerance and can be used as evidence for the occurrence of toxic effects in a specific sediment. In category F pure chemicals are tested with a pure culture of microorganisms under sediment conditions. The results of category F tests can be combined with single species tests with animals and plants to obtain sediment quality guidelines sufficient for species protection. This can be compared with the sediment quality guidelines which protect sediment functions. When one of these quality guidelines is exceeded for a compound at a specific location a category E test can be used to determine whether the compound shows toxic effects in that sediment.  相似文献   

8.
To determine changes in metal distribution, bioavailability and toxicity with sediment depth, two 20-cm-long replicate cores were collected from a lake historically subjected to the influence of metal mining and smelting activity. The vertical distribution of Pb, Cd and Cu in sediment was similar for all three metals, with the surface layers showing enrichment and the deeper (pre-industrial) layers showing lower concentrations. Toxicity of each sediment core section was determined in laboratory tests with the freshwater amphipod Hyalella azteca. Bioavailable metal in each sediment slice was estimated from metal concentrations in overlying water in these toxicity tests and, for Cd, also from metal bioaccumulation. The profile for Cd in tissue was comparable to Cd in sediment and overlying water, but relative Cd bioavailability from sediment increased with sediment depth. Survival increased with increasing sediment depth, suggesting that surface sediments were probably less or non-toxic before industrialization.  相似文献   

9.
Photochemical grid models are addressing an increasing variety of air quality related issues, yet procedures and metrics used to evaluate their performance remain inconsistent. This impacts the ability to place results in quantitative context relative to other models and applications, and to inform the user and affected community of model uncertainties and weaknesses. More consistent evaluations can serve to drive improvements in the modeling process as major weaknesses are identified and addressed. The large number of North American photochemical modeling studies published in the peer-reviewed literature over the past decade affords a rich data set from which to update previously established quantitative performance “benchmarks” for ozone and particulate matter (PM) concentrations. Here we exploit this information to develop new ozone and PM benchmarks (goals and criteria) for three well-established statistical metrics over spatial scales ranging from urban to regional and over temporal scales ranging from episodic to seasonal. We also recommend additional evaluation procedures, statistical metrics, and graphical methods for good practice. While we primarily address modeling and regulatory settings in the United States, these recommendations are relevant to any such applications of state-of-the-science photochemical models. Our primary objective is to promote quantitatively consistent evaluations across different applications, scales, models, model inputs, and configurations. The purpose of benchmarks is to understand how good or poor the results are relative to historical model applications of similar nature and to guide model performance improvements prior to using results for policy assessments. To that end, it also remains critical to evaluate all aspects of the model via diagnostic and dynamic methods. A second objective is to establish a means to assess model performance changes in the future. Statistical metrics and benchmarks need to be revisited periodically as model performance and the characteristics of air quality change in the future.

Implications: We address inconsistent procedures and metrics used to evaluate photochemical model performance, recommend a specific set of statistical metrics, and develop updated quantitative performance benchmarks for those metrics. We promote quantitatively consistent evaluations across different applications, scales, models, inputs, and configurations, thereby (1) improving the user’s ability to quantitatively place results in context and guide model improvements, and (2) better informing users, regulators, and stakeholders of model uncertainties and weaknesses prior to using results for policy assessments. While we primarily address U.S. modeling and regulatory settings, these recommendations are relevant to any such applications of state-of-the-science photochemical models.  相似文献   


10.
Deterioration of overlying water quality during toxicity tests with benthic invertebrates is a serious problem with some sediments. One solution is periodic renewal of overlying water. However, this is either labour intensive or requires construction and maintenance of special equipment. Furthermore, water renewal has the potential for flushing toxic chemicals out of the test chamber and establishes nonequilibrium conditions between the water and sediment. An alternative is testing under static conditions using atypical test vessels (e.g. Imhoff settling cones) with a large water volume (1 l) overlaying a much smaller sediment volume (e.g. 15 ml). This results in dramatic improvement of overlying water quality compared to standard static toxicity tests. Compared to water renewal, the test method is much simpler, all toxic substances leached from the sediment are retained in the test vessel, and contaminant concentrations in water and sediment have more time to equilibrate. Chronic sediment toxicity tests (10-28 days) have been conducted successfully under these conditions with Chironomus riparius, Hexagenia sp., Hyalella azteca and Tubifex tubifex.  相似文献   

11.
This paper reports results of genotoxicity and toxicity studies of water and sediment samples collected from the Estancia Velha stream of southern Brazil, a stream transporting both domestic sewage and effluents from regional factories working in the leather industry. Three sites were selected: in the stream headwaters (Site 1), located downstream of an urban area (Site 2), and near the basin outfall (Site 3). Results obtained with Allium cepa showed no evidence of chromosomal mutation, either in water or in sediment, during winter or summer seasons, but samples collected below Site 1 showed high toxicity. Physical and chemical analyses showed high concentrations of pollutants at these sites. Ecotoxicity tests with Daphnia magna and Ceriodaphnia dubia measured toxicity in water from Sites 2 and 3 in summer 2004. A toxic effect on Hyalella azteca was only found in sediment from Site 3 during winter 2003 and summer 2004. The results suggest that the synergy among different compounds in domestic and industrial sewage discharges can make it difficult to maintain system stability.  相似文献   

12.
The sensitivity of the benthic amphipod species Ampelisca brevicornis and Corophium volutator to dredged sediments was compared through simultaneous testing on the standard 10 days sediment toxicity test. The results of mortality obtained for 22 harbor sediments sampled at several Spanish ports were studied together with the physico-chemical characteristics of the samples to obtain the incidence of toxicity in terms of dredged material categories and to identify possible differences in the amphipod mortality results when using one or another test species. The results showed a similar incidence of toxicity for medium-high and highly contaminated sediments for both amphipod species, similar to that obtained through the comparison of the chemical concentrations measured in sediments with the single limit values used in Spain for dredged material characterization and management. On the contrary, C. volutator presented a higher mortality and a higher incidence of toxicity when exposed to low and medium-low contaminated sediments, which may have been caused by the lower sensitivity of A. brevicornis when exposed to sediments from its natural environment. When compared to other amphipod species used for whole sediment toxicity assessment, both amphipod species used in this study reported slightly higher sensitivities although these differences could have been associated to the different set of chemical compounds considered when characterizing the sediment samples. In this sense, the amphipod mortality results were better predicted through the use of mean quotients than just by comparing the measured chemical concentrations with the single limit values used in Spain, which indicates that the toxic response of both species was caused by the cocktail of contaminants present in the sediments. Finally, the correlation analysis identified a higher association between A. brevicornis mortality and the metallic contaminants while C. volutator was more correlated with the organic micro-pollutants. Despite these differences, the results indicate that Ampelisca brevicornis can be used as test organism for dredged material characterization when enough individuals of other recommended species such as Corophium volutator are not available.  相似文献   

13.
An automated water-renewal toxicity test system is described for exposing benthic invertebrates to whole sediments. The system will intermittently deliver laboratory or on-site water for overlying water replacement in sediment exposures. A range of cycle rates can be used to produce different volume additions of overlying water per day to exposure chambers. The system can be used with six different treatments and eight replicates per treatment producing 48 exposure chambers. Three formulated sediments with variable organic carbon (1.5%, 7.5%) and sand (14%, 63%) content were prepared to test the system exposing amphipods, Hyalella azteca and midges, Chironomus tentans in 10 day whole sediment tests. Intermittent water flow was used with a 90 min cycle time to create two volume additions of laboratory water per 24 h in exposure chambers (180 ml sediment, 320 ml water). Overlying water quality conditions, and survival and growth of both species were consistent and within acceptable limits for the testing requirements of the U.S. EPA guidelines for sediments with freshwater invertebrates.  相似文献   

14.
The concentration partitioning between the sediment particle and the interstitial water phase plays an important role in controlling the toxicity of heavy metals in aquatic systems. The aim of this study was to assess the sediment quality in a polluted area of the Ziya River, Northern China. The contamination potential and bioavailability of six metals were determined from the concentrations of total metals and the bioavailable fractions. The results showed that the concentrations of Cr, Cu, Ni, Zn, and Pb exceeded the probable effect concentration at several sites. The high geoaccumulation indices showed that the sediments were seriously contaminated by Cd. The ratio of acid-volatile sulfide (AVS) to simultaneously extracted metal (SEM) was higher than 1, which indicated that the availability of metals in sediments was low. The risk assessment of interstitial waters confirmed that there was little chance of release of metals associated with acid-volatile sulfide into the water column. Values of the interstitial water criteria toxicity unit indicated that none of the concentrations of the studied metals exceeded the corresponding water quality thresholds of the US Environmental Protection Agency. Positive matrix factorization showed that the major sources of metals were related to anthropogenic activities. Further, if assessments are based on total heavy metal concentrations, the toxicity of heavy metals in sediment may be overestimated.  相似文献   

15.
A suite of tests was conducted to evaluate and identify the cause or causes of toxicity in Passaic River sediments. Sediment toxicity was measured with three types of bioassays: a whole sediment bioassay with the marine amphipod, Ampelisca abdita, and interstitial water bioassays with A. abdita and the bioluminescent bacterium Vibrio fisheri (Microtox((R))). In addition, a Phase I Toxicity Identification Evaluation (TIE) was conducted to elucidate the cause of observed toxicity. Analytical concentrations of selected residues in whole sediment and interstitial water from the five sampling stations were considered in conjunction with the conclusions drawn from the toxicity tests and Phase I TIE results. Finally, a toxic units approach was used to evaluate the predicted toxicity of measured interstitial water residue concentrations. There was a lack of toxic response in the short-term interstitial water bioassays, indicating that oxidants, soluble forms of metals, and dissolved phase neutral organics were not likely toxicants. However, there was significant toxicity indicated by the whole sediment A. abidita bioassays. After 10 days, there was complete or near complete mortality in amphipods exposed to all of the sediment samples tested. Removal of interstitial water toxicity by filtration was common to all four stations that exhibited measurable initial toxicity. The observed toxicity characteristics are consistent with particle associated neutral organics. This conclusion is supported by toxicity removal via filtration, lack of toxicity in the Microtox((R)) assays, and the fact that whole sediments were more toxic than was interstitial water.  相似文献   

16.
To seasonally evaluate littoral contamination, toxicity and quality values of sediments from the Gulf of Cádiz, we measured chemical concentrations and conducted toxicity tests in winter and summer and linked these results by means of multivariate analysis. Sediment samples were subjected to two separate, replicated sediment toxicity tests (Microdeutopus gryllotalpa amphipod survival, and Ruditapes philippinarum clam reburial), and to comprehensive sediment chemistry analyses (grain size, organic carbon, 14 heavy metals, and the surfactant linear alkylbenzenesulfonate (LAS)). Only sediments associated with an untreated urban discharge were toxic and related to high levels of surfactant LAS, Ag, and Pb. Multivariate analysis indicated that variables and chemicals associated with geochemical matrix and background levels (specific surface, Fe, Zn, Cu, V, Ni, and Co), chemicals associated with untreated urban discharge sources, and toxicity effects showed no seasonal variability. Only copper concentrations showed seasonal differences, being toxic during the winter and not toxic during summer. Multivariate analysis permits us to derive sediment quality values (SQVs); in terms of concentrations at or below which biological effects were not measured (mg kg(-1) dry sediment), are: LAS, 2.6; lead, 66.8; silver, 0.78; copper, 69.6.  相似文献   

17.
Bioaccumulation and chronic toxicity of nickel (Ni) to Hyalella azteca in Ni-spiked sediments was strongly affected by the source of sediment used. The total range in LC50s on a sediment concentration basis ranged over 20 fold. Differences in Ni toxicity generally matched differences in Ni bioaccumulation, and toxicity expressed on a body concentration basis varied less than three fold. Body concentrations, therefore, provide a much more reliable prediction of Ni toxicity in sediments than do concentrations in the sediment. Ni in overlying water was also a reliable predictor of Ni toxicity, but only in tests conducted in Imhoff settling cones with large (67:1) water to sediment ratios. Overlying water LC50s for tests in beakers varied 18 fold. Sediment and body concentrations of Ni tolerated by Hyalella were slightly higher in cones than in beakers. Reproduction was not affected significantly by Ni at concentrations below the LC50 and 10-week EC50s for survival and biomass production (including survival, growth and reproduction) were only marginally lower than 4-week EC50s (survival and growth only).  相似文献   

18.
Demirak A  Yilmaz F  Tuna AL  Ozdemir N 《Chemosphere》2006,63(9):1451-1458
Concentrations of heavy metals (Cd, Cr, Cu, Pb and Zn) were measured in water, bottom sediment and tissues (muscle and gills) of Leuciscus cephalus from the Dipsiz stream in the Yatagan basin (southwestern Turkey), the site of a thermal power plant. Results for levels in water were compared with national and international water quality guidelines, as well as literature values were reported for streams and rivers. Comparisons were made of metal concentrations in water and sediment with those in the muscle and gills of L. cephalus caught from the Dipsiz stream. We found that there was metal accumulation in the gills compared to the muscle. Concentrations of Cd, Pb, Zn and Cr in the gills were higher than that in the muscle; however, Cu levels were higher in muscle than that in gills. Concentrations of heavy metals in L. cephalus muscle were below the legal limits for human consumption, although Cr, Pb and Zn levels in the gills were above the limits in the fish taken from the Dipsiz stream. On the other hand, no correlation was found between metal concentrations in water and sediment or between metal concentrations in water and muscle and gills of L. cephalus. A positive correlation was found between concentrations of Cu and Zn in the sediment and in fish tissue, whereas there was no relationship between other metal concentrations in the sediment and water, and muscle and gills of L. cephalus. As with water, Pb and Cd concentrations in particular were higher in sediment than that in background levels. The results show that the pollutants from the thermal power plant may be a source of these elements.  相似文献   

19.
The Salinas River is the largest of the three rivers that drain into the Monterey Bay National Marine Sanctuary in central California. Large areas of this watershed are cultivated year-round in row crops and previous laboratory studies have demonstrated that acute toxicity of agricultural drainwater to Ceriodaphnia dubia is caused by the organophosphate (OP) pesticides chlorpyrifos and diazinon. In the current study, we used a combination of ecotoxicologic tools to investigate incidence of chemical contamination and toxicity in waters and sediments in the river downstream of a previously uncharacterized agricultural drainage creek system. Water column toxicity was investigated using a cladoceran C. dubia while sediment toxicity was investigated using an amphipod Hyalella azteca. Ecological impacts of drainwater were investigated using bioassessments of macroinvertebrate community structure. The results indicated that Salinas River water downstream of the agricultural drain is acutely toxic to Ceriodaphnia, and toxicity to this species was highly correlated with combined toxic units (TUs) of chlorpyrifos and diazinon. Laboratory tests were used to demonstrate that sediments in this system were acutely toxic to H. azteca, which is a resident genus. Macroinvertebrate community structure was moderately impacted downstream of the agricultural drain input. While the lowest macroinvertebrate abundances were measured at the station demonstrating the greatest water column and sediment toxicity and the highest concentrations of pesticides, macroinvertebrate metrics were more significantly correlated with bank vegetation cover than any other variable. Results of this study suggest that pesticide pollution is the likely cause of laboratory-measured toxicity in the Salinas River samples and that this factor may interact with other factors to impact the macroinvertebrate community in the system.  相似文献   

20.
Potential threats to drinking water and water quality continue to be a major concern in many regions of the United States. New Jersey, in particular, has been at the forefront of assessing and managing potential contamination of its drinking water supplies from hazardous substances. The purpose of the current analysis is to provide an up-to-date evaluation of the occurrence and detected concentrations of methyl tertiary butyl ether (MTBE) and several other volatile organic compounds (VOCs) in public water systems, private wells, and ambient groundwater wells in New Jersey based on the best available data, and to put these results into context with federal and state regulatory and human-health benchmarks. Analyses are based on the following three databases that contain water quality monitoring data for New Jersey: Safe Drinking Water Information System (SDWIS), Private Well Testing Act (PWTA), and National Water Information System (NWIS). For public water systems served by groundwater in New Jersey, MTBE was detected at a concentration ≥10 μg/L, ≥20 μg/L, and ≥70 μg/L at least once in 30 (2%), 21 (1.4%), and five (0.3%) of sampled systems from 1997 to 2011, respectively. For private wells in New Jersey, MTBE was detected at a concentration ≥10 μg/L, ≥20 μg/L, and ≥70 μg/L at least once in 385 (0.5%), 183 (0.2%), and 46 (0.05%) of sampled wells from 2001 to 2011, respectively. For ambient groundwater wells in New Jersey, MTBE was detected at a concentration ≥10 μg/L, ≥20 μg/L, and ≥70 μg/L at least once in 14 (2.1%), 9 (1.3%), and 4 (0.6%) of sampled wells from 1993 to 2012, respectively. Average detected concentrations of MTBE, as well as detected concentrations at upper-end percentiles, were less than corresponding benchmarks for all three datasets. The available data show that MTBE is rarely detected in various source waters in New Jersey at a concentration that exceeds the State's health-based drinking water standard or other published benchmarks, and there is no evidence of an increasing trend in the detection frequency of MTBE. Other VOCs, such as tetrachloroethylene (PCE), trichloroethylene (TCE), and benzene, are detected more often above corresponding regulatory or human-health benchmarks due to their higher detected concentrations in water and/or greater toxicity values. The current analysis provides useful data for evaluating the nature and extent of historical and current contamination of water supplies in New Jersey and potential opportunities for public exposures and health risks due to MTBE and other VOCs on a statewide basis. Additional forensic or forecasting analyses are required to identify the sources or timing of releases of individual contaminants at specific locations or to predict potential future water contamination in New Jersey.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号