生物流化床及臭氧氧化处理中低浓度糖业废水

采用内循环好氧生物流化床对中低浓度糖业废水进行生物降解,当进水COD、NH3-N浓度分别为400～600mg/L和7～11 mg/L时,其相应去除率达到80%～90%和70%～80%,处理效果良好;COD容积负荷可达到5.1 kg COD/(m3·d),反应器具有较强的抗负荷冲击能力.采用臭氧氧化工艺对COD浓度为28...     

反应沉淀一体式矩形环流反应器处理城市污水的影响因素研究

通过中试研究了不同溶解氧浓度、有机负荷、HRT条件下,反应沉淀一体式矩形环流反应器(RPIR)对深圳市南山污水处理厂低C/N城市污水的处理效果。结果表明,在控制溶解氧浓度为1 mg/L、COD容积负荷小于2.5 kg/m3.d、NH4+-N容积负荷不超过0.2 kg/(m3.d)、HRT为4 h时,COD平均去除率可达90%,NH4+-N平均去除率超过80%。RPIR在处理该城市污水过程中具有良好的抗冲击负荷能力,污染物去除效率高,运行稳定。     

好氧颗粒污泥的培养及处理味精废水

以厌氧颗粒污泥为接种污泥,在模拟废水条件下利用SBR 35 d成功培养出了具有同步硝化反硝化作用的好氧颗粒污泥,反应器对COD和NH4+-N去除率分别高于95%和99%。将该反应器用于处理味精废水,当COD、NH4+-N的容积负荷分别为2.4 kg/(m3.d)、0.24 kg/(m3.d)时,COD、NH4+-N和TN去除率分别高于90%、99%和85%。处理味精废水后的颗粒污泥粒径由之前的0.8～2.5 mm减小至0.6～1.8 mm,颗粒结构较之前更加密实。     

溅水充氧生物滤池处理农村污水的研究

开发了一种处理农村污水的低能耗地埋式一体化溅水充氧生物滤池装置,通过拔风和溅水复合充氧技术实现了大幅度节能条件下的好氧生物处理.考察了在不同水力负荷及COD、NH4 -N容积负荷条件下本装置的处理效果,结果表明,在水力负荷小于10 m3/(m2·d)、COD及NH4 -N容积负荷分别小于0.3 kg COD/(m3·d)和0.08 kg NH4 -N/(m3·d)的条件下,可以取得较高的去除效果和良好的出水水质,COD、NH4 -N和TN的平均出水浓度分别为58.94 mg/L、2.78 mg/L和8.23 mg/L,平均去除率分别为51.7%、86.4%和70.6%.     

复合生物滤池处理城市高污染水体

采用中试规模复合生物滤池处理城市高污染水体,考察了滤池的最佳运行参数以及对氮和有机物的去除效果。结果表明:滤池容积负荷宜控制为0.3～0.5 kg COD/(m3.d),水力负荷4.5～5 m3/(m2.d),适宜的通风比为9%,当C/N为5～8时,滤池COD、NH4+-N和TN平均去除率分别为80%、83%和63%,达到高效同步硝化反硝化状态。     

组合填料生物滤池处理锦纶废水二级出水的性能研究

为解决纺织行业水回用问题,采用陶粒和活性炭组合填料生物滤池对锦纶废水二级生物处理出水进行了深度净化,并考察了气水比和水力负荷对曝气生物滤池处理效果的影响.研究结果表明,曝气生物滤池处理效果良好,平均出水COD、NH4 -N和TN分别为32 mg/L、1.5 mg/L和8.1 mg/L.随着气水比的增加,COD和NH4 -N平均去除率相应提高,TN平均去除率先增大后降低,当气水比为2∶1时,COD、NH4 -N和TN平均去除率分别为48.30%、84.24%和42.18%;随着水力负荷的增加,COD、NH4 -N和TN平均去除率均降低,当水力负荷为0.39 m3/m2·h时,COD、NH4 -N和TN平均去除率分别为48.33%、84.81%和42.54%.     

超声波-膜生物法联合处理垃圾焚烧厂渗滤液

采用超声波-膜生物法(MBR)联合处理垃圾渗滤液,探讨了超声波辐射时间和MBR的水力负荷对COD、NH3-N和TP去除的影响。结果表明,(1)超声波单独处理时,超声波辐射时间在30～90 s时,COD、NH3-N最大增加率分别34.31%、3.36%,而对TP的去除没有影响;(2)超声波-膜生物(MBR)联合处理时,超声波辐射时间为300 s,MBR的水力负荷为6.4 L/(m2.d)时,COD、NH3-N和TP的最佳去除率分别为92.20%、80.10%和91.12%;MBR的水力负荷为12.8 L/(m2.d),超声波辐射时间在5～20 min时,COD、NH3-N的最佳去除率分别为92.34%、79.93%,TP的浓度低于0.2 mg/L;MBR反应时间为7 h,超声波辐射时间为5～20 min,与未进行超声波辐射处理(超声波辐射时间为0 min)相比,COD、NH3-N的去除率增加了11.37%、15.26%;超声波预处理有助于提高后续MBR对COD、NH3-N的去除作用。     

水力负荷对厌氧氨氧化反应器运行影响的研究

采用一套有效容积为4.46 L的UASB-ANAMMOX反应器,通过对水力负荷进行3个阶段的调节,研究水力停留时间对ANAMMOX反应器处理效果的影响.3个阶段的水力负荷分别为0.20～0.25、0.38～0.43、0.16～0.20 L/(Ld).在试验过程中,水力负荷的冲击对NH 4-N、NO-2-N的去除率影响明显.其中水力负荷为0.20～0.25 L/(L·d)时,NH 4-N、NO-2-N去除率都能达到99%以上;当水力负荷为0.38～0.43 L/(L·d)时,NH 4-N、NO-2-N去除率分别降至64%和62%;当水力负荷为0.16～0.20 L/(L·d)时,NH 4-N、NO-2-N去除率立刻分别回升至94%和97%.ANAMMOX反应过程中,NO-2-N和NH 4-N的去除量比值基本在1.3∶1.0左右变化,ANAMMOX反应的优势菌种代谢在运行过程中会将一部分NO-2-N转化为NO-3-N,水力负荷的改变对NO-3-N的出水浓度影响不大;但NO-3-N日生成量与水力负荷的大小成正比.试验表明,UASB-ANAMMOX反应器对水力负荷冲击有较强的抵抗力,但是仍会造成一定量的ANAMMOX反应的优势菌流失,使该反应器在短时间内不能恢复最佳的去除效果.     

AFB-SBR工艺处理蓝皮制革工业废水

采用厌氧流化床(AFB)-序批式反应器(SBR)工艺处理蓝皮制革工业废水。分别考察了水力停留时间(HRT)、容积负荷对厌氧流化床以及曝气时间、污泥浓度、溶解氧浓度对SBR反应器处理效果的影响。试验结果表明,AFB将实验废水的BOD_5/COD(B/C)值由0.19～0.26提高至0.35～0.42,有效提高了其可生化性;在进水COD浓度为1 700～1 890 mg/L、HRT为1 d、容积负荷为1.792 kg COD/(m~3·d)时,COD去除率达65.2%～68.5%,且具有良好的抗冲击负荷能力。SBR在进水COD浓度为628～712 mg/L、污泥浓度为2.9 g/L、曝气时间为10 h、溶解氧浓度为2 mg/L工况下,COD去除率达87.6%,NH_3-N去除率达93.6%,处理后出水水质符合污水综合排放标准(GB 8978-1996)中的一级标准要求。     

Biostyr曝气生物滤池处理城市污水的沿程生化特性

青岛市麦岛污水处理厂采用曝气生物滤池(BAF)处理城市污水,以稳定运行的Biostyr为研究载体,考察滤池COD、NH3-N、SS和细菌数量等生化特性的沿程变化.结果表明,在气水比为4∶1～5∶1、进水COD负荷为2.5 ～3.7 kg/(m3·d)、进水NH3-N负荷为0.18～0.57 kg/(m3·d)时,滤池对COD的降解主要在150 cm填料以下处,COD的去除率可达58.9％;NH3-N去除率沿滤柱高度的变化与COD有所不同,在100 cm以下填料处,NH3-N的去除率仅为3.6％,在100 ～350 cm填料之间,NH3-N的去除率增加迅速,可达56.1％;对SS的去除主要发生在100 cm填料以下,去除率达51.7％.     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.     

Biochemical interaction of six op delayed neurotoxicants with several neurotargets

Abstract

Five organophosphorous insecticides: Leptophos, EPN, Cyano‐fenphos, trichloronate and salithion proved to cause irreversible ataxia not only to chicken but also to mice and sheep. TOCP was included as a reference. Cyanofenphos blocked the catecholamine B‐receptor binding activity with ³H‐norepinephrine at a level similar to that of the specific inhibitor propranolol in the mouse heart preparation. In the lamb heart preparation, the B‐receptor was more sensitive to Leptophos, salithion and TOCP than to propranolol. The six compounds and their oxons were screened for their in‐vitro inhibition to monamine oxidase (MAO), acetyl cholinesterase (AChE) and neurotoxic esterase (NTE) in the brain of either mouse, lamb or chicken. It is believed that their AChE inhibition stands for their acute toxicity, while NTE inhibition is responsible for their paralytic ataxia.     

Phytoextraction of lead-contaminated soil using vetivergrass (<Emphasis Type="Italic">Vetiveria zizanioides</Emphasis> L.), cogongrass (<Emphasis Type="Italic">Imperata cylindrica</Emphasis> L.) and carabaograss (<Emphasis Type="Italic">Paspalum conjugatum</Emphasis> L.)

Background, Aims and Scope The global problem concerning contamination of the environment as a consequence of human activities is increasing. Most of the environmental contaminants are chemical by-products and heavy metals such as lead (Pb). Lead released into the environment makes its way into the air, soil and water. Lead contributes to a variety of health effects such as decline in mental, cognitive and physical health of the individual. An alternative way of reducing Pb concentration from the soil is through phytoremediation. Phytoremediation is an alternative method that uses plants to clean up a contaminated area. The objectives of this study were: (1) to determine the survival rate and vegetative characteristics of three grass species such as vetivergrass, cogongrass and carabaograss grown in soils with different Pb levels; and (2) to determine and compare the ability of the three grass species as potential phytoremediators in terms of Pb accumulation by plants. Methods The three test plants: vetivergrass (Vetiveria zizanioides L.); cogongrass (Imperata cylindrica L.); and carabaograss (Paspalum conjugatum L.) were grown in individual plastic bags containing soils with 75 mg kg⁻¹ (37.5 kg ha⁻¹) and 150 mg kg⁻¹ (75 kg ha⁻¹) of Pb, respectively. The Pb contents of the test plants and the soil were analyzed before and after experimental treatments using an atomic absorption spectrophotometer. This study was laid out following a 3 × 2 factorial experiment in a completely randomized design. Results On the vegetative characteristics of the test plants, vetivergrass registered the highest whole plant dry matter weight (33.85–39.39 Mg ha⁻¹). Carabaograss had the lowest herbage mass production of 4.12 Mg ha⁻¹ and 5.72 Mg ha⁻¹ from soils added with 75 and 150 mg Pb kg⁻¹, respectively. Vetivergrass also had the highest percent plant survival which meant it best tolerated the Pb contamination in soils. Vetivergrass registered the highest rate of Pb absorption (10.16 ± 2.81 mg kg⁻¹). This was followed by cogongrass (2.34 ± 0.52 mg kg⁻¹) and carabaograss with a mean Pb level of 0.49 ± 0.56 mg kg⁻¹. Levels of Pb among the three grasses (shoots + roots) did not vary significantly with the amount of Pb added (75 and 150 mg kg⁻¹) to the soil. Discussion Vetivergrass yielded the highest biomass; it also has the greatest amount of Pb absorbed (roots + shoots). This can be attributed to the highly extensive root system of vetivergrass with the presence of an enormous amount of root hairs. Extensive root system denotes more contact to nutrients in soils, therefore more likelihood of nutrient absorption and Pb uptake. The efficiency of plants as phytoremediators could be correlated with the plants’ total biomass. This implies that the higher the biomass, the greater the Pb uptake. Plants characteristically exhibit remarkable capacity to absorb what they need and exclude what they do not need. Some plants utilize exclusion mechanisms, where there is a reduced uptake by the roots or a restricted transport of the metals from root to shoots. Combination of high metal accumulation and high biomass production results in the most metal removal from the soil. Conclusions The present study indicated that vetivergrass possessed many beneficial characteristics to uptake Pb from contaminated soil. It was the most tolerant and could grow in soil contaminated with high Pb concentration. Cogongrass and carabaograss are also potential phytoremediators since they can absorb small amount of Pb in soils, although cogongrass is more tolerant to Pb-contaminated soil compared with carabaograss. The important implication of our findings is that vetivergrass can be used for phytoextraction on sites contaminated with high levels of heavy metals; particularly Pb. Recommendations and Perspectives High levels of Pb in localized areas are still a concern especially in urban areas with high levels of traffic, near Pb smelters, battery plants, or industrial facilities that burn fuel ending up in water and soils. The grasses used in the study, and particularly vetivergrass, can be used to phytoremediate urban soil with various contaminations by planting these grasses in lawns and public parks. ESS-Submission Editor: Dr. Willie Peijnenburg (wjgm.peijnenburg@rivm.nl)