Photocatalytic degradation of the herbicide pendimethalin using nanoparticles of BaTiO3/TiO2 prepared by gel to crystalline conversion method: a kinetic approach

Photocatalytic degradation of the herbicide, pendimethalin (PM) was investigated with BaTiO3/TiO2 UV light system in the presence of peroxide and persulphate species in aqueous medium. The nanoparticles of BaTiO3 and TiO2 were obtained by gel to crystallite conversion method. These photo catalysts are characterized by energy dispersive x-ray analysis (EDX), scanning electron microscope (SEM), x-ray diffraction (XRD), and Brunauer-Emmett-Teller (BET) adsorption isotherm and reflectance spectral studies. The quantum yields for TiO2 and BaTiO3 for the degradation reactions are 3.166 Einstein m(-2) s(-1) and 2.729 Einstein m(-2) s(-1) and catalytic efficiencies are 6.0444 x 10(-7) mg(-2)h(-1)L2 and 5.403 x 10(-7) mg(-2)h(-1)L2, respectively as calculated from experimental results. BaTiO3 exhibited comparable photocatalytic efficiency in the degradation of pendimethalin as the most widely used TiO2 photocatalyst. The persulphate played an important role in enhancing the rate of degradation of pendimethalin when compared to hydrogen peroxide. The degradation process of pendimethalin followed the first-order kinetics and it is in agreement with Langmuir-Hinshelwood model of surface mechanism. The reason for high stability of pendimethalin for UV-degradation even in the presence of catalyst and oxidizing agents were explored. The higher rate of degradation was observed in alkaline medium at pH 11. The degradation process was monitored by spectroscopic techniques such as ultra violet-visible (UV-Vis), infrared (IR) and gas chromatography mass spectroscopy (GC-MS). The major intermediate products identified were: N-propyl-2-nitro-6-amino-3, 4-xylidine, (2, 3-dimethyl-5-nitro-6-hydroxy amine) phenol and N-Propyl-3, 4-dimethyl-2, 6-dinitroaniline by GC-MS analysis and the probable reaction mechanism has been proposed based on these products.     

Photocatalytic degradation of the herbicide pendimethalin using nanoparticles of BaTiO3/TiO2 prepared by gel to crystalline conversion method: A kinetic approach

Photocatalytic degradation of the herbicide, pendimethalin (PM) was investigated with BaTiO₃/TiO₂ UV light system in the presence of peroxide and persulphate species in aqueous medium. The nanoparticles of BaTiO₃ and TiO₂ were obtained by gel to crystallite conversion method. These photo catalysts are characterized by energy dispersive x-ray analysis (EDX), scanning electron microscope (SEM), x-ray diffraction (XRD), and Brunauer-Emmett-Teller (BET) adsorption isotherm and reflectance spectral studies. The quantum yields for TiO₂ and BaTiO₃ for the degradation reactions are 3.166 Einstein m^?2 s^?1 and 2.729 Einstein m^?2 s^?1 and catalytic efficiencies are 6.0444 × 10^?7 mg^?2h^?1L² and 5.403 × 10^?7 mg^?2h^?1L², respectively as calculated from experimental results. BaTiO₃ exhibited comparable photocatalytic efficiency in the degradation of pendimethalin as the most widely used TiO₂ photocatalyst. The persulphate played an important role in enhancing the rate of degradation of pendimethalin when compared to hydrogen peroxide. The degradation process of pendimethalin followed the first-order kinetics and it is in agreement with Langmuir-Hinshelwood model of surface mechanism. The reason for high stability of pendimethalin for UV-degradation even in the presence of catalyst and oxidizing agents were explored. The higher rate of degradation was observed in alkaline medium at pH 11. The degradation process was monitored by spectroscopic techniques such as ultra violet-visible (UV-Vis), infrared (IR) and gas chromatography mass spectroscopy (GC-MS). The major intermediate products identified were: N-propyl-2-nitro-6-amino-3, 4-xylidine, (2, 3-dimethyl-5-nitro-6-hydroxy amine) phenol and N-Propyl-3, 4-dimethyl-2, 6-dinitroaniline by GC-MS analysis and the probable reaction mechanism has been proposed based on these products.     

Synthesis of branched para-nonylphenol isomers: occurrence and quantification in two commercial mixtures

Eight tertiary nonanols were synthesized via Grignard reaction and coupled by Friedel–Crafts alkylation with phenol to the corresponding nonylphenols. Six branched para-nonylphenols (NP) were obtained: 4-(3′-methyl-3′-octyl)phenol (33NP), 4-(2′-methyl-2′-octyl)phenol (22NP), 4-(2′,5′-dimethyl-2′-heptyl)phenol (252NP), 4-(2′,5′,5′-trimethyl-2′-hexyl)phenol (2552NP), 4-(2′,4′-dimethyl-2′-heptyl)phenol (242NP) and 4-(4′-ethyl-2′-methyl-2′-hexyl)phenol (4E22NP). Their structures were confirmed by GC–MS and NMR spectroscopy. These six isomers as well as the earlier synthesized 4-(3′,5′-dimethyl-3′-heptyl)phenol (353NP), 4-(3′,6′-dimethyl-3′-heptyl)phenol (363NP) and 4-(2′,6′-dimethyl-2′-heptyl)phenol (262NP) were compared with commercial NP mixtures purchased from Acros and Fluka by GC–MS (equipped with a 100 m polysiloxane column). The analyses revealed that all obtained isomers are occurring in different quantities in both commercial NP mixtures.     

Light-induced transformation of tribenuron-methyl on glass, soil, and plant surface

Photolysis of tribenuron-methyl (methyl 2-[[[[N-(4-methoxy-6-methyl-1,3,5triazin-2-yl)methylamino]carbonyl]amino]sulfonyl]benzoate), a sulfonylurea herbicide, was studied as thin film on glass surface, soil surface, and plant surface. A number of photoproducts such as 4-methoxy-6-methyl-2-aminomethyl-1,3,5-triazine; methyl-2-(aminosulfonyl) benzoate; N-(2-carbomethoxyphenyl)-N-(4-methoxy-6-methyl-1,3,5-triazin-2-yl)-N'-methylurea; N-(2-carbomethoxyphenyl sulfonyl)-N-methyl urea; o-benzoic sulfimide and 4-methoxy-6-methyl-2-amino-1,3,5-triazine were identified by comparison of their GC-MS with the authentic standards. The rate of degradation in all the cases followed first-order kinetics with a statistically significant correlation coefficient. Rate of photodegradation was greater on glass surface than on soil surface.     

Biodegradation of juvenoid diastereoisomers: radio-HPLC and MS analysis

Microbial degradation of two diastereoisomeric forms 2 and 3 of a selected juvenoid (insect juvenile hormone bioanalog), ethyl N-{2-{4-[(2-hydroxycyclohexyl)methyl]phenoxy}ethyl}carbamate was studied and the degradation products analyzed. Degradation experiments were performed using simple modeling under laboratory conditions. A Candida sp. strain T1, isolated from soil, was chosen as a biodegradation species. Radiolabeling of the studied compounds 2 and 3 was used in combination with radio-HPLC and MS analysis to increase the limits of detection, monitoring and isolation of trace quantities of the products of degradation and/or transformation. Resulting from the microbial processes using 2 or 3 as source compounds, three identical products (4-6) of their biodegradation were produced. Compound 2 also afforded two additional products (7, 8). Radio-HPLC analysis and separation, and subsequent MS analysis of the degradation mixtures resulted in identification of the degradation products. The degree and the rate of biodegradation of 2 and 3 were analyzed after 1, 3 and 7 days from the beginning of the experiment.     

Effect of systemic herbicides on N2-fixing and phosphate solubilizing microorganisms in relation to availability of nitrogen and phosphorus in paddy soils of West Bengal

A field experiment has been conducted with four systemic herbicides viz., butachlor [N-(butoxymethyl)-2-chloro-2',6'-diethyl-acetanilide], fluchloralin [N-(2-chloroethyl)-(2,6-dinitro-N-propyl-4-trifluoromethyl) aniline], oxadiazon [5-terbutyl-3-(2,4-dichloro-5-isopro poxyphenyl)-1,3,4-oxadiazol-2-one] and oxyfluorfen [2-chloro-1-(3-ethoxy-4-nitrophenyl)-4-(trifluoromethyl) benzene] at their recommended field rates (2.0, 1.5, 0.4 and 0.12kga.i.ha(-1), respectively) to investigate their effects on growth and activities of aerobic non-symbiotic N(2)-fixing bacteria and phosphate solubilizing microorganisms in relation to availability of nitrogen and phosphorus in the rhizosphere soils as well as yield of the rice crop (Oryza sativa L cv. IR-36). Application of herbicides, in general, highly stimulated the population and activities of the target microorganisms, which resulted in a greater amount of atmospheric nitrogen fixation and phosphate solubilization in the rhizosphere soils of the test crop. The greater microbial activities subsequently augmented the mineralization and availability of nitrogen and phosphorus in the soil solution, which in turn increased the yield of the crop. Among the herbicides, oxyfluorfen was most stimulative followed by fluchloralin and oxadiazon in augmenting the microbial activities in soil. Butachlor also accentuated the mineralization and availability of nitrogen due to higher incitement of non-symbiotic N(2)-fixing bacteria in paddy soil. The grain and straw yields of the crop were also significantly increased due to the application of oxyfluorfen (20.2% and 21%) followed by fluchloralin (13.1% and 15.4%) and butachlor (9.1% and 10.2%), respectively.     

Transport modes and pathways of the strongly sorbing pesticides glyphosate and pendimethalin through structured drained soils

Leaching of the strongly sorbing pesticides glyphosate and pendimethalin was evaluated in an 8-month field study focussing on preferential flow and particle-facilitated transport, both of which may enhance the leaching of such pesticides in structured soils. Glyphosate mainly sorbs to mineral sorption sites, while pendimethalin mainly sorbs to organic sorption sites. The two pesticides were applied in equal dosage to a structured, tile-drained soil, and the concentration of the pesticides was then measured in drainage water sampled flow-proportionally.The leaching pattern of glyphosate resembled that of pendimethalin, suggesting that the leaching potential of pesticides sorbed to either the inorganic or organic soil fractions is high in structured soils. Both glyphosate and pendimethalin leached from the root zone, with the average concentration in the drainage water being 3.5 and 2.7 μg L⁻¹, respectively. Particle-facilitated transport (particles >0.24 μm) accounted for only a small proportion of the observed leaching (13-16% for glyphosate and 16-31% for pendimethalin). Drain-connected macropores located above or in the vicinity of the drains facilitated very rapid transport of pesticide to the drains. That the concentration of glyphosate and pendimethalin in the drainage water remained high (>0.1 μg L⁻¹) for up to 7 d after a precipitation event indicates that macropores between the drains connected to underlying fractures were able to transport strongly sorbing pesticides in the dissolved phase. Lateral transport of dissolved pesticide via such discontinuities implies that strongly sorbing pesticides such as glyphosate and pendimethalin could potentially be present in high concentrations (>0.1 μg L⁻¹) in both water originating from the drainage system and the shallow groundwater located at the depth of the drainage system.     

Accelerated remediation of pesticide-contaminated soil with zerovalent iron

High pesticide concentrations in soil from spills or discharges can result in point-source contamination of ground and surface waters. Cost-effective technologies are needed for on-site treatment that meet clean-up goals and restore soil function. Remediation is particularly challenging when a mixture of pesticides is present. Zerovalent iron (Fe0) has been shown to promote reductive dechlorination and nitro group reduction of a wide range of contaminants in soil and water. We employed Fe0 for on-site treatment of soil containing > 1000 mg metolachlor, > 55 mg alachlor, > 64 mg atrazine, > 35 mg pendimethalin, and > 10 mg chlorpyrifos kg(-1). While concentrations were highly variable within the windrowed soil, treatment with 5% (w/w) Fe0 resulted in > 60% destruction of the five pesticides within 90 d and increased to > 90% when 2% (w/w) Al2(SO4)3 was added to the Fe0. GC/MS analysis confirmed dechlorination of metolachlor and alachlor during treatment. Our observations support the use of Fe0 for ex situ treatment of pesticide-contaminated soil.     

Enhanced chemical oxidation of aromatic hydrocarbons in soil systems

Fenton's destruction of benzene, toluene, ethylbenzene, and xylene (BTEX) was investigated in soil slurry batch reactors. The purpose of the investigation was to quantify the enhancement of oxidation rates and efficiency by varying process conditions such as iron catalyst (Fe(II) or Fe(III); 2, 5, and 10mM), hydrogen peroxide (H2O2; 30, 150, 300 mM), and metal chelating agents (l-ascorbic acid, gallic acid, or N-(2-hydroxyethyl)iminodiacetic acid). Rapid contaminant mass destruction (97% after 3h) occurred in the presence of 300 mM H2O2 and 10 mM Fe(III). An enhanced removal rate (>90% removal after 15 min and 95% removal after 3h) was also observed by combining Fe(III), N-(2-hydroxyethyl)iminodiacetic acid and 300 mM H2O2. The observed BTEX mass removal rate constants (3.6-7.8 x 10(-4)s(-1)) were compared to the estimated rate constants (4.1-10.1 x 10(-3)s(-1)). The influence of non-specific oxidants loss (by reaction with iron hydroxides and soil organic matter) was also explored.     

Effect of green manure amendment on herbicide pendimethalin on soil

Manure amendment in agricultural practice can have a large effect on herbicide dissipation because the period of manure plowing is close to the period of herbicide application. In addition, manure amendment is among the frequently encountered options in ameliorating pesticide pollution. In this research, the dissipation of the herbicide pendimethalin was examined after amendment with two common green manures, Lupinus luteus (L) or Cosmos bipinnatus (C), for 110 days in pH 5.2 and 7.7 soils (Sankengtzu [Sk] and Erhlin [Eh] soil, respectively). The microbial activity and ecology changes were examined by using Biolog EcoPlate and denaturing gradient gel electrophoresis (DGGE). In Sk soil, the half-lives of pendimethalin with L, C, and blank treatment were 49.0, 54.9, and 62.2 days, respectively, whereas that in Eh soil they were 46.3, 52.6, and 34.8 days, respectively. Pendimethalin dissipated quickly in more neutral soil (Eh soil), but the addition of manure can only increase the dissipation rate in acidic soil (Sk soil), indicating that the amendment of manures exerted different effect in pendimethalin dissipation rates in different pH soils. The application of pendimethalin and/or manure altered the microbial community activity after 24 h of incubation. After 110 days, the microbial community activities in green manure–amended soil were more similar to that with blank than pendimethalin treatment in both types of soils. In comparison with treatment C, microbial communities were more similar between treatment L and blank, indicating the superior effect over pendimethalin on microbial communities when applying Lupinus luteus. The research showed that the application of herbicide pendimethalin changed soil microbial community, and the amendment of manures exerted different effect in pendimethalin dissipation rates in different pH soils. It is assumed that the change in dissipation rates was originated from the microbial community change after different manure amendment.     

DOM-Flocculation: A suitable approach for separating free and DOM-bound herbicides?

Dissolved organic matter (DOM) in soil solution is considered to interact with herbicides enhancing their mobility and promoting subsequent leaching. Batch experiments were conducted to test if free and DOM-bound herbicides can be separated by a DOM-flocculation technique with Cu as a coagulant. DOM was extracted from the H and A horizons of two soils (Terric Histosol, Cumuli-Calcaric Cambisol) and from the O horizon of a forest soil (Humic Cambisol). DOM-solutions (100 mL) were fortified with the herbicides terbuthylazine and pendimethalin (100 μg active ingredient each) and equilibrated for 14 hours. After DOM-flocculation with Cu (addition of 0,5 mM CuCl₂) herbicide recovery was determined in the supernatant solutions and in the precipitate of Humic Cambisol-DOM, respectively. Recovery of the herbicides from pure water was 85–99% and was not influenced by the addition of Cu. At low pH (4,8–5,3) DOM-flocculation of different DOM-extracts was insufficient and varied in a range of 18 – 90%. Herbicide recovery from DOM-solutions decreased moderately for terbuthylazine (60–90%) and strongly for pendimethalin (5 – 30%). In general, the addition of Cu caused no further reduction of herbicide recovery from supernatant solutions, except for Humic Cambisol-DOM. The effects of Cu-addition were most evident for pendimethalin (strongly reduced concentration in the supernatant solutions) and were considered to be caused by a flocculation of DOM-bound moieties. Flocculation of Humic Cambisol-DOM increased from 18 – 24% at pH 5 to > 95% at pH 8. However, at this pH the formation of Cu(OH)₂ as a sorbing subcomponent of the flocculated matter lead to an overestimation of DOM-bound pendimethalin. Calculating this side effect 6% of pendimethalin added was DOM-bound. Only traces of terbuthylazine (< 1%) were found in the solid matter of flocculated Humic Cambisol-DOM. To sum up, the new approach to separate freely dissolved herbicides from DOM-bound moieties not fully corresponded to our expectations. DOM-flocculation was found to depend strongly on pH-environment influencing not only DOM-herbicide interactions but also the clear separation of DOM-bound herbicides from herbicides in solutions.     

Acetamiprid, carbendazim, diuron and thiamethoxam sorption in two Brazilian tropical soils

Sorption of acetamiprid ((E)-N1-[(6-chloro-3-pyridyl)methyl]-N2-cyano-N1-methylacetamidine), carbendazim (methyl benzimidazol-2-ylcarbamate), diuron (N-(3,4-dichlorophenyl)-N, N-dimethyl urea) and thiamethoxam (3-(2-chloro-thiazol-5-ylmethyl)-5-methyl-[1,3,5]oxadiazinan-4-ylidene-N-nitroamine) was evaluated in two Brazilian tropical soils, Oxisol and Entisol, from Primavera do Leste region, Mato Grosso State, Brazil. To describe the sorption process, batch experiments were carried out. Linear and Freundlich isotherm models were used to calculate the K(d) and K(f) coefficients from experimental data. The K(d) values were utilized to calculate the partition coefficient normalized to soil organic carbon (K(oc)). For the pesticides acetamiprid, carbendazim, diuron and thiamenthoxan the K(oc) (mL g(- 1)) values ranged in both soils from 98 - 3235, 1024 - 2644, 145 - 2631 and 104 - 2877, respectively. From the studied pesticides, only carbendazim presented correlation (r(2) = 0.82 and p < 0.01) with soil organic carbon (OC) content. Acetamiprid and thiamethoxam showed low sorption coefficients, representing a high risk of surface and ground water contamination.     

Selenium extractability from a contaminated fine soil fraction: implication on soil cleanup

Two batches of fine soil fraction of an acidic soil were deliberately contaminated with selenite (Se(IV)) and selenate (Se(VI)), respectively, and aged for more than 220 days. Speciation analysis using continuous flow-through hydride generation atomic absorption spectrometry (HGAAS) indicated that the species were predominant in their respective aged soils. A selective sequential extraction scheme was employed to fractionate the Se retained in the soils into six fractions of varying retentions. Abilities of various chemical reagents in extracting the Se in the two soil batches were then evaluated. The reagents investigated were sodium salts such as sodium chloride (NaCl), sodium sulfate (Na2SO4), sodium carbonate (Na2CO3), and sodium phosphate (Na3PO4), and two oxidants, namely, hydrogen peroxide (H2O2) and potassium permanganate (KMnO4). It was found that NaCl, Na2SO4, and Na2CO3 could only extract the exchangeable fraction of Se, while Na3PO4 could extract the exchangeable and strongly-bound fractions. Selenate was extracted more than Se(IV) by the salts. The kinetics of Se(IV) extraction by Na3PO4 could be best described by the Elovich model, while the Ritchie second-order model was the most appropriate to describe Se(VI) extraction. Efficiencies of the oxidants in Se(IV) extraction highly depended on their applied dosages. Both H2O2 and KMnO4 were able to extract greater than 93% of total Se, and therefore were significantly more effective than the salts in Se(IV) extraction.     

Effects of sensitizers on the photodegradation of the systemic fungicide triadimenol

The photochemical behaviour of triadimenol (1) under various conditions has been examined. Significant degradation is obtained only in the presence of electron-acceptor sensitizers as 9,10-dicyanoanthracene or 2,4,6-triphenylpyrylium tetrafluoroborate, and long irradiation times are required. 1H-1,2,4-Triazole (2), 4-chlorophenyl formate (3), 4-chlorophenol (4), 1-(4-chlorophenoxy)-3,3-dimethyl-1-(1H-1,2,4-triazol-1-yl)butan-2-one (5), 4-chlorophenyl 2,2-dimethylpropanoate (6) and 4-chlorobenzoic acid (7) were identified as photoproducts by NMR and GC-MS.     

Leaching of pesticides through normal-tillage and low-tillage soil--a lysimeter study. II. Glyphosate

Glyphosate is a widely used non-selective herbicide. Leaching of glyphosate (N-(phosphonomethyl)glycine) and/or its metabolite AMPA (aminomethylphosphonic acid) was studied in four lysimeters, two of them being replicates from a low-tillage field (lysimeter 3 and 4), the other two being replicates from a normal tillage field (lysimeter 5 and 6). In both cases the soil was a sandy loam soil with 13-14% clay. The lysimeters had a surface area of 0.5 m2 and a depth of 110 cm. Lysimeter 3 and 4 were sprayed with a mixture of 14C-labelled glyphosate and unlabelled glyphosate, while lysimeter 5 and 6 were sprayed with unlabelled glyphosate. The spraying took place September 18, 1997. The total amount of glyphosate sprayed onto each lysimeter was 40 mg, corresponding to 0.8 kg active ingredient per ha. The lysimeters were installed in an outdoor system in Research Centre Flakkebjerg and were thus exposed to normal climatic conditions of the area. A mean of 260 l drainage water were collected from lysimeter 3 and 4 and a mean of 375 litres from lysimeter 5 and 6. The mean yearly concentration of leached glyphosate and/or AMPA was significantly below 0.1 microg/l from both sets of lysimeters, and thus no significant difference between the two lysimeter sets was shown. However, in both sets of lysimeters several single findings at concentrations above 0.1 microg/l was seen, which might be due to the leaching of particle-bound compounds. A significant difference between the soil residual concencentrations of AMPA was seen, the higher concentration was found in the set of lysimeter where low-tillage had been practiced and where Round Up had been used several times in the years before sampling of the lysimeter soil.     

Fate of anilide and aniline herbicides in plant-materials-amended soils

The fate of herbicides trifluralin, pendimethalin, alachlor and metolachlor in paddy field soils amended with plant materials was investigated. The plant materials were purple sesbania, vegetable soybean and rice straw. The investigation was performed at two temperatures (25 and 40 degrees C) and two soil water moistures (60 and 90% water-holding capacity). The results showed linear and Freudlich equations described the adsorption of amide compound to soil. Adsorption coefficient (K(d)) fit to linear equation were in general greater in plant material-amended soils than in non-amended soil, especially in soil amending with rice straw. Increasing temperature and soil water moisture content shortened the half-lives of compounds in various treated soils. The movement of compounds in the soil columns showed the maximum distribution of aniline type compound, trifluralin and pendimethalin, appeared at the upper top of 0 to 5 and 0 to 10 cm of soil column, respectively, and of anilide type, alachlor and metolachlor, were distributed at 0 to 25 cm of the soil column. The mobility of chemicals in the different treated soils was simulated by the behavior assessment model (BAM). There was no significant difference among different plant material incubated soils on dissipation and mobility of compounds in soils.     

Degradation in soil and water and ecotoxicity of rimsulfuron and its metabolites.

The degradation and ecotoxicity of sulfonylurea herbicide rimsulfuron and its major metabolites were examined in batch samples of an alluvial sandy loam and in freshwater. An HPLC-DAD method was adapted to simultaneously identify and quantify rimsulfuron and its metabolites, which was successfully validated by GC-MS analysis. In aqueous solutions, pure rimsulfuron was rapidly hydrolyzed into metabolite 1 (N-(4,6-dimethoxypyrimidin-2-yl)-N-(3-(ethylsulfonyl)-2-pyridinylurea)), which itself was transformed into the more stable metabolite 2 (N-((3-(ethylsulfonyl)-2-pyridinyl)-4,6-dimethoxy-2-pyrimidineamine)), with half-life (t(1/2)) values of 2 and 2.5 days, respectively. Hydrolysis was instantaneous under alkaline conditions (pH = 10). In aqueous suspensions of the alluvial soil (pH = 8), formulated rimsulfuron had a half-life of 7 days, whereas that of metabolite 1 was similar to that in water (about 3.5 days). The degradation of the two major metabolites was also studied in soil suspensions with the pure compounds at concentrations ranging from 1 to 10 mg l(-1). The half-life of metabolite 1 ranged from 3.9 to 5 days, close to the previous values. Metabolite 2 was more persistent and its degradation is strongly dependent on the initial concentration (C0): half-life values ranged from 8.1 to 55 days at 2-10 mg l(-1), respectively. These values are higher than those determined from the kinetics of metabolite 1 transformation into metabolite 2 (t(1/2) = 8-19 days). The ecotoxicity of the three chemicals was evaluated through their effect on Daphnia magna and Vibrio fischeri (Microtox bioassay). No effect was observed on D. magna with 24 and 48 h acute toxicity tests. Similarly, no toxic effect was observed with the Microtox test for the three chemicals in the range of concentrations tested that included the field application dose. Thus, being of low persistence and lacking acute toxicity, these chemicals present a low environmental risk. However, chronic effects should be studied in order to confirm the safety of rimsulfuron and its major metabolites.     

Sorption behavior of metolachlor, isoproturon, and terbuthylazine in soils

The sorption-desorption of metolachlor [2-chloro-N-(ethyl-6-methyl phenyl)-N-(2-methoxy-1-methyl ethyl) acetamide], isoproturon [3-(4-isopropyl phenyl)-1,1-dimethyl urea] and terbuthylazine [N6-tert butyl-6-chloro-N4-ethyl-1,3,5-triazine-2,4-diamine] herbicides was studied in two German soils at 1:10 soil to water ratio by batch method. Equilibrium of herbicides between soil and water (0.01 M CaCl2) was attained in 2 h. Sorption data fitted very well to Freundlich equation, represented by very high correlation coefficient (r2 > 0.934). Comparison of Freundlich K values indicated that sorption of all the three herbicides was most pronounced in soil having higher organic carbon content. Koc values were as expected nearly identical for each herbicide in the two soils. The Freundlich constant (1/n) was about 1 for metolachlor and less than 1 for terbuthylazine and isoproturon indicating a L-type of sorption isotherms. Desorption of all the three herbicides showed hysteresis. Nearly equal amounts of metolachlor, isoproturon and terbuthylazine were desorbed from both soils. There was a good correlation between Koc and solubility.     

Transfer of hexazinone and glyphosate through undisturbed soil columns in soils under Christmas tree cultivation

Field studies monitoring pesticide pollution in the Morvan region (France) have revealed surface water contamination by some herbicides. The purpose of this study was to investigate in greater detail the transport of two herbicides, used in Christmas tree production in the Morvan, under controlled laboratory conditions. Thus, the leaching of hexazinone (3-cyclohexyl-6-dimethyl-amino-1-methyl-1,3,5-triazine-2,4 (1H,3H) dione) and glyphosate (N-(phosphono-methyl-glycine)) through structured soil columns was studied using one loamy sand and two sandy loams from sites currently under Christmas tree cultivation in the Morvan. The three soils were cultivated sandy brunisol [Sound reference base for soils, D. Baize, M.C. Girard (Coord.), INRA, Versailles, 1998, 322 p] or, according to the FAO [FAO, World reference base for soil resources, ISSS-ISRIC-FAO, FAO, Rome, Italy, 1998], the La Garenne was an arenosol and the two other soils were cambisols. The clay contents of the soils ranged from 86 to 156 g kg(-1) and the organic carbon ranged from 98 to 347 g kg(-1). After 160 mm of simulated rainfall applied over 12 days, 2-11% of the applied hexazinone was recovered in the leachate. The recovery was much higher than that of glyphosate, which was less than 0.01%. The greater mobility of hexazinone might be related to its much lower adsorption coefficient, K(oc), 19-300 l kg(-1), compared with 8.5-10231 l kg(-1) for glyphosate (literature values). Another factor that may explain the higher amounts of hexazinone recovered in the leachates of the three soil columns is its greater persistence (19.7-91 days) relative to that of glyphosate (7.9-14.4 days). The mobility of both herbicides was greater in the soils with higher gravel contents, coarser textures, and lower organic carbon contents. Moreover, glyphosate migration seems negatively correlated not only to soil organic carbon, but also to aluminium and iron contents of soils. This soil column study suggests that at the watershed scale, surface water contamination by hexazinone could occur via the horizontal subsurface flow in upper centimeters of soil. In contrast, the surface water contamination with glyphosate by this mechanism appears unlikely.     

Geochemistry of inorganic arsenic and selenium in a tropical soil: effect of reaction time, pH, and competitive anions on arsenic and selenium adsorption

Factors that can affect As and Se adsorption by soils influence the bioavailability and mobility of these elements in the subsurface. This research attempted to compare the adsorption capacities of As(III), As(V), Se(IV), and Se(VI) on a tropical soil commonly found in Singapore in a single-species system. The effect of reaction time, pH, and competitive anions at different concentrations on the adsorption of both As and Se species were investigated. The As and Se adsorption isotherm were also obtained under different background electrolytes. The batch adsorption experiments showed that the sequence of the As and Se adsorption capacities in the soil was As(V) > Se(IV) > As(III) > Se(VI). The adsorption kinetics could be best described by the Elovich equation. The adsorption of As(V), Se(IV), and Se(VI) appeared to be influenced by the variable pH-dependent charges developed on the soil particle surfaces. Phosphate had more profound effect than SO4(2-) on As and Se adsorption in the soil. The competition between PO4(3-) and As or Se oxyanions on adsorption sites was presumably due to the formation of surface complexes and the surface accumulation or precipitation involving PO4(3-). The thermodynamic adsorption data for As(V) and Se(IV) adsorption followed the Langmuir equation, while the As(III) and Se(VI) adsorption data appeared to be best-represented by the Freundlich equation.