Investigation of the usage of centrifuging waste of mineral wool melt (CMWW), contaminated with phenol and formaldehyde,in manufacturing of ceramic products

Large amounts of centrifuging waste of mineral wool melt (CMWW) are created during the production of mineral wool. CMWW is technogenic aluminum silicate raw material, formed from the particles of undefibred melt (60–70%) and mineral wool fibers (30–40%). 0.3–0.6% of organic binder with phenol and formaldehyde in its composition exists in this material. Objective of the research is to investigate the possibility to use CMWW as an additive for the production of ceramic products, by neutralising phenol and formaldehyde existing in CMWW. Formation masses were prepared by incorporating 10%, 20% and 30% of CMWW additive and burned at various temperatures. It was identified that the amount of 10–30% of CMWW additive influences the following physical and mechanical properties of the ceramic body: lowers drying and firing shrinkage, density, increases compressive strength and water absorption. Investigations carried out show that CMWW waste can be used for the production of ceramic products of various purposes.     

Characterization of ceramic roof tile wastes as pozzolanic admixture

The aim of this work is to study the recycling of tile wastes in the manufacture of blended cements. Cracked or broken ceramic bodies are not accepted as commercial products and, therefore, the unsold waste of the ceramic industry becomes an environment problem. The use of powdered roof tile in cement production, as pozzolanic addition, is reported. The wastes were classified as nonglazed, natural and black glazed tiles. The mineralogy of the powders was controlled by SEM-EDX microscopy, XRD analysis and FTIR spectroscopy. Particle size was checked by laser granulometry. Once the materials were fully characterized, pozzolanic lime consumption tests and Fratini tests were carried out. Different formulations of cement-tile blends were prepared by incorporation of up to 30% weight ratios of recycled waste. The compressive strength of the resulting specimens was measured. The evolution of hydration of the cement-tile blends was analyzed by XRD and FTIR techniques. Vibrational spectroscopy presented accurate evidence of pozzolanic activity. The results of the investigation confirmed the potential use of these waste materials to produce pozzolanic cement.     

Effect of sintering temperature on the properties and leaching of incinerator bottom ash.

The fine particle size fraction of municipal solid waste incinerator bottom ash is often problematic because reuse applications for this material are limited. In these experiments incinerator bottom ash with a particle size of less than 8 mm was processed using conventional ceramic production techniques involving wet milling, drying, compacting and sintering. The effect of sintering temperature on the sintered density, microstructure, acid neutralization capacity (ANC) and the release of metal ions as a function of leachate pH are reported. Sintering at 1080 degrees C produced samples with maximum density. This material contained diopside (CaMgSi2O6), clinoenstatite (Mg2Si2O6) and wollastonite (CaSiO3) as the major crystalline phases. The acid neutralization capacity of sintered samples is significantly lower than milled bottom ash, and further reduces as the sintering temperature increases. This is associated with reduced leaching of Ca from sintered ash samples under all leachate pH conditions. Heavy metals present in the incinerator bottom ash included Cr, Cu, Ni, Zn, Cd and Pb. Sintering under optimum conditions reduced the leachable fraction of these metals under aggressive acid conditions (leachate pH 3) by factors ranging from 90% for Ni to greater than 99% for Cr, Cd, Zn and Pb.     

Performance of recycled ceramic waste as aggregates in hot mix asphalt (HMA)

Ceramic waste materials from the production of titles has increased over the years. Preliminary studies on the properties of ceramics showed that this material can be incorporated into asphalt mixtures as aggregates. Laboratory tests were conducted to evaluate the feasibility of utilizing ceramic materials from tile manufacturing firms. A study was undertaken to look into the performance of crushed ceramics that were incorporated in asphalt mixtures to replace the conventional granite aggregates from sizes 5.0 mm down including the 75 micron filler. The replacement was done proportionally with a 0, 20, 40, 60, 80, and 100% percent by weight of granite aggregates. The outcome of the study showed that the performance of recycled ceramic aggregates in hot mix asphalt (HMA) reached an optimum at about 20% which means there is a great potential for the use of it in asphalt mixtures. The Marshall stability showed an increment of about 25% while the resilient modulus strength improved by 13.5% as compared with the control specimen. All samples were analyzed at various proportions of ceramic–granite aggregate combination and were observed that a 20% use of 5 mm down ceramic aggregates blended with granite aggregates produce higher strength HMA.     

Use of glazed ceramic waste as additive in mortar and the mathematical modelling of its strength

This study investigated the reusability of waste material from the tile manufacturing industry as an alternative material to natural pozzolan trass. Yield strength values of mortar made from Portland cement (CEM 142.5), were measured by adding glazed ceramic waste and trass at various weight ratios (5 to 40%). The test results proved that the strength values at 2, 7, and 28 days gave good results for concentrations of waste materials less than 5-10% in the cement. A decrease in strength was observed at higher concentrations. Mathematical modelling results showed a logarithmic correlation between the mortar strength and weight fraction of cement.     

UTILIZING THE USED CATALYST FROM REFINERY FCC UNITS AS A SUBSTITUTE FOR KAOLIN IN FORMULATING CERAMIC FRITS

Frits are materials of a vitreous nature which are used for obtaining the glaze used to coat glazed ceramic tiles. One of the raw materials usually employed in preparing frits is kaolin, which provides the aluminium and part of the silicon they contain.This study investigates the possibility of utilizing the used catalyst from the FCC (fluidized catalyst cracking) units involved in petroleum refining, to substitute for kaolin as a raw material in the preparation of ceramic frits. On assessing the aesthetic and technical characteristics (whiteness, gloss, microhardness, etc.) of the glazes obtained from two frits that were prepared by substituting kaolin with the industrial waste mentioned above, no important differences were observed relative to the characteristics of the glazes obtained from the standard frits.     

Immobilization of copper ions laden kaolin waste: influence of thermal treatment on its immobilization in cement paste

This work aims to study the influence of thermal treatment of Cu²⁺ laden kaolin wastes on its immobilization efficiency in cement paste. Compressive strength and toxicity characteristic leaching procedure (TCLP) of 5–20 % kaolin waste blended cement pastes were tested. X-ray diffraction (XRD) results illustrate that adsorption of Cu²⁺ ions modify the crystal structure of kaolinite mineral. Fourier transform infrared (FTIR) results indicate that the adsorption sites on the kaolin surface that were occupied with free water molecules have been replaced with Cu²⁺ ions adsorbed from aqueous solutions. The thermal treatment of kaolin waste improves fixation ratio of Cu²⁺ in cement pastes containing up to 20 % of thermally treated waste. This is due to: pozzolanic activity of calcined kaolin, conversion of leachable adsorbed Cu²⁺ ions into encapsulated unleachable phase that does not retard the hydration of cement as well as adsorption of much of leachable Cu²⁺ ions on surfaces of hydration products and occlusion in its lattice structure as illustrated from XRD, FTIR, thermogravimetric, scanning electron microscopy and TCLP results. The fixation ratio of Cu²⁺ in cement paste blended with 20 % of thermally treated kaolin waste, reaches maximum value of about 97 % compared to 82 % for cement paste blended with 20 % of untreated kaolin waste.     

Recycling of iron foundry sand and glass waste as raw material for production of whiteware.

The purpose of this study was to evaluate the production feasibility of triaxial whiteware using sand from cast iron moulds as a raw material instead of silica, and recycled glass in place of feldspar. Formulations were prepared using sand, glass waste, and white-firing clay such that only 50% of the composition was virgin material (clay). The ceramic bodies were formed by pressing and fired at different temperatures (between 1100 and 1300 degrees C). Specimens were characterized in terms of green density prior to firing; and their flexural strength, linear shrinkage, and water absorption were measured after firing. The microstructure was determined by scanning electron microscopy. Possible environmental impacts of this recycling process were also evaluated, through solubility and leaching tests, according to Brazilian standards. Gaseous emissions during the firing process were also analysed. The results showed that it is possible to produce triaxial ceramics by using such alternative raw materials.     

Electrostatic painting residues as an alternative raw material for red clay industry.

In this study, the viability of using electrostatic painting residues--paint sludge--as a raw material to the red clay industry was investigated. Red clay-based ceramic masses containing electrostatic paint residues were formulated during the study. The clays were obtained from the Rio do Rastro deposit, in Gravataí, and were of the standard formulation used in industry. Different ceramic mass formulations with additions of 0.5, 1.0, 2.5 and 5.0 wt.% electrostatic painting residue in addition to a formulation with no residue addition (standard formulation), were evaluated. The samples were uniaxially pressed in a double-effect press and were fired in an electric oven at 900, 950 and 1000 degrees C. The firing at constant temperature lasted 8 h, and heating rate was 150 K h(-1). After processing the samples were characterized in terms of their physical and mechanical properties. Environmental compatibility was also considered by the evaluation of gaseous emissions and leaching and solubilization tests according to the Brazilian standards NBR 10.005 and NBR 10.006, respectively. The results showed that it was possible to produce ceramic materials containing electrostatic painting residues within their formulations.     

Immobilization of radioactive waste by cementation with purified kaolin clay

A study is undertaken to determine the waste immobilization performance of low-level wastes in cement-clay mixtures. Liquid low-level wastes are precipitated using chemical methods, followed by solidification in drums. Solidification is done using cementation processes. Long-term leaching rates of the radionuclides are used as indicators of immobilization performance of solidified waste forms. In addition to evaluating the effects of kaolin clay on the leaching properties of the cemented waste forms, the effect of addition of kaolin on the strength of the cemented waste form is also investigated. The long term leaching tests show that inclusion of kaolin in cement reduces the leaching rates of the radionuclides significantly. However, clay additions in excess of 15 wt.% causes a significant decrease in the hydrolytic stability of cemented waste form. It is found that the best waste isolation, without causing a loss in the mechanical strength, is obtained when the kaolin content in cement is 5%.     

Fly ash of mineral coal as ceramic tiles raw material

The aim of this work was to evaluate the use of mineral coal fly ash as a raw material in the production of ceramic tiles. The samples of fly ash came from Capivari de Baixo, a city situated in the Brazilian Federal State of Santa Catarina. The fly ash and the raw materials were characterized regarding their physical chemical properties, and, based on these results; batches containing fly ash and typical raw materials for ceramic tiles were prepared. The fly ash content in the batches varied between 20 and 80 wt%. Specimens were molded using a uniaxial hydraulic press and were fired. All batches containing ash up to 60 wt% present adequate properties to be classified as several kinds of products in the ISO 13006 standard () regarding its different absorption groups (pressed). The results obtained indicate that fly ash, when mixed with traditional raw materials, has the necessary requirements to be used as a raw material for production of ceramic tiles.     

Utilization of municipal solid waste incineration (MSWI) fly ash in ceramic brick: product characterization and environmental toxicity

In this study, municipal solid waste incineration (MSWI) fly ash was used as a blending in making ceramic brick based on its characterization and an orthogonal test was performed to determine the optimal mixture ratio of the materials. Besides, the fired bricks made in accordance with the optimal mixture ratio were characterized for performance, phase transformation, microstructure, leaching toxicity of the heavy metals in accordance with GB/T 2542-92 (Detection methods for bricks analysis, China) and by means of XRD, SEM and leaching toxicity analysis. It was found that the optimal mixture ratio of materials (MSWI fly ash:red ceramic clay:feldspar:gang sand) was 20:60:10:10 by mass, and the optimal sintering temperature was 950 °C. Leaching results of heavy metals from sintered bricks were reduced considerably in comparison with those from green bricks prior to sintering process. The results as a whole suggested that utilization of MSWI fly ash in ceramic brick constituted a potential means of adding value.     

Inertization of hazardous dredging spoils

Vitrification and production of ceramics materials starting from sediment excavated from Venice lagoon is described. This sediment is classified as toxic waste because contains several heavy metal ions and organic pollutants and was successfully vitrified at 1200-1350 degrees C. Twenty weight percentage of glass cullet, coming from a community glass recycling program, was added to the raw materials, previously calcined at 900 degrees C, as a way of adjusting the variations of composition of the individual sediment batches. Chemical durability (leaching) tests showed that the optimized glass compositions are inert, and thus not only volume reduction but also inertization of the waste was obtained by this process. Moreover, the economics of the entire process was analysed. The valorization of the waste was accomplished by the subsequent processing of the glass derived from the inertization. Glass ceramic materials were produced by viscous phase sintering of pressed glass powders which crystallized during the densification process. Sintered glass ceramic products had good mechanical characteristics (HV = 7.5 GPa, bending strength 150 +/- 8 MPa), making them suitable for applications in the building industry.     

Effects of calcium hydroxide and calcium chloride addition to bentonite in iron ore pelletization.

Pyrite ash is created as waste from the roasting of pyrite ores during the production of sulphuric acid. These processes generate great amounts of pyrite ash waste that is generally land filled. This creates serious environmental pollution due to the release of acids and toxic substances. Pyrite ash waste can be utilized in the iron production industry as a blast furnace feed to process this waste and prevent environmental pollution. The essential parameters affecting the pelletization process of pyrite ash were studied using bentonite as a binder. Experiments were then carried out using bentonite and a mixture of bentonite with calcium hydroxide and calcium chloride in order to make the bentonite more effective. The metallurgical properties of pyrite ash, bentonite, calcium hydroxide, calcium chloride, a mixture of these and sintered pellets were studied using X-ray analysis. The crushing strength tests were carried out to investigate the strength of pyrite ash waste pellets. The results of these analyses showed that pyrite ash can be agglomerated to pellets and used in the iron production industry as a blast furnace feed. The crushing strength of the pellets containing calcium hydroxide and calcium chloride in addition to bentonite was better than the strength of pellets prepared using only bentonite binder.     

Characteristics of bricks made from waste steel slag

The characteristics of bricks made from steel slag were investigated in this research. Slag addition was shown to reduce the required firing temperature. When the firing temperature was greater than 1050 degrees C and the slag addition less than 10%, the bricks met ROC national standard CNS 3319 third-class brick for builders. The percentage of slag increased as the quartz and kaolin decreased in the sintered samples while the magnesium aluminum silicate and calcium silicate increased. There were no new crystal phases observed in these samples.     

Use of waste gypsum to replace natural gypsum as set retarders in portland cement

The present study is focused on clarifying the influence of waste gypsum (WG) in replacing natural gypsum (NG) in the production of ordinary Portland cement (OPC). WG taken from slip casting moulds in a ceramic factory was formed from the hydration of plaster of paris. Clinker and 3–5 wt% of WG was ground in a laboratory ball mill to produce cement waste gypsum (CMWG). The same procedure was repeated with NG to substitute WG to prepare cement natural gypsum (CMNG). The properties of NG and WG were investigated via X-ray Diffraction (XRD), X-ray fluorescence (XRF) and differential scanning calorimetry (DSC)/thermogravimetric (TG) to evaluate the properties of CMNG and CMWG. The mechanical properties of cement were tested in terms of setting time, flexural and compressive strength. The XRD result of NG revealed the presence of dihydrate while WG contained dihydrate and hemihydrate. The content of dihydrate and hemihydrates were obtained via DSC/TG, and the results showed that WG and NG contained 12.45% and 1.61% of hemihydrate, respectively. Furthermore, CMWG was found to set faster than CMNG, an average of 15.29% and 13.67% faster for the initial and final setting times, respectively. This was due to the presence of hemihydrate in WG. However, the values obtained for flexural and compressive strength were relatively the same for CMNG and CMWG. Therefore, this result provides evidence that WG can be used as an alternative material to NG in the production of OPC.     

Separability studies of construction and demolition waste recycled sand

The quality of recycled aggregates from construction and demolition waste (CDW) is strictly related to the content of porous and low strength phases, and specifically to the patches of cement that remain attached to the surface of natural aggregates. This phase increases water absorption and compromises the consistency and strength of concrete made from recycled aggregates. Mineral processing has been applied to CDW recycling to remove the patches of adhered cement paste on coarse recycled aggregates. The recycled fine fraction is usually disregarded due to its high content of porous phases despite representing around 50% of the total waste.This paper focus on laboratory mineral separability studies for removing particles with a high content of cement paste from natural fine aggregate particles (quartz/feldspars). The procedure achieved processing of CDW by tertiary impact crushing to produce sand, followed by sieving and density and magnetic separability studies. The attained results confirmed that both methods were effective in reducing cement paste content and producing significant mass recovery (80% for density concentration and 60% for magnetic separation). The production of recycled sand contributes to the sustainability of the construction environment by reducing both the consumption of raw materials and disposal of CDW, particularly in large Brazilian centers with a low quantity of sand and increasing costs of this material due to long transportation distances.     

Recycling of calcium fluoride sludge as ceramic material using low temperature sintering technology

The Chinese integrated circuit industry has been transformed from a small state-owned sector into a global competitor, but chip manufacturing produces large amounts of calcium fluoride sludge (CFS). The current treating method is landfill in China. In order to solve the problem of unavailable landfill sites and the dissolved CFS polluting water sources, CFS was tested as a component for a ceramic product made with sodium borate, sodium phosphate, and waste alumina using a low temperature sintering technology. The ceramic was characterized by X-ray diffraction (XRD), microstructure, compressive strength. XRD and microstructure analyses verified that CFS was transformed into Na₂Ca(PO₄)F as an inert crystalline phase in ceramic, which is enclosed by the borophosphate glass liquid phase. Toxicity characteristic leaching procedure and corrosion resistance tests verified that fluorine from CFS was solidified in the inert crystalline phase, which did not release to cause secondary pollution. This novel technology produces high-performance ceramic as a construction material, in accordance with the concept of sustainable development.     

Preparation and characterization of ceramic products by thermal treatment of sewage sludge ashes mixed with different additives

The study of the ceramic characteristics of sludge ashes, alone or mixed with additives (kaolin, montmorillonite, illitic clay, powdered flat glass) includes characterization of additives, preparation of probes (dry or wet mixed), thermal treatment (up to 1200 degrees C, except melting or deformation) and control (densities, compressive strengths and water absorption). Thermal treatment increases the density and compressive strength of probes (both parameters go through maxima, with later decreases) and decreases the absorption of water. The densification is also revealed by the evolution of the ratio of decrease of volume/loss of mass. The maximum values of compressive strengths were obtained for 25% of illitic clay, montmorillonite and glass powder. Densification concerning probes with sludge ashes alone does not occur with kaolin. Experimental data were adjusted to exponential relationships between compressive strengths and densities for every composition, and also to a general equation for all probes. The apparent density obtained was adjusted to a non-linear dependence with temperature, leading to a maximum in density and permitting calculating the temperature of occurrence of this maximum. The adjustment was not possible for probes containing kaolin, requiring presumably higher temperatures to densify. Water absorption has low values for ashes or kaolin probes, intermediate values for illite and powdered flat glass probes and high values for montmorillonite probes. Excepting with kaolin, ceramic materials with better characteristics than sludge ashes without additives were obtained at lower treatment temperatures.     

Improvement of Physico-mechanical Properties of Chitosan Films by Photocuring with Acrylic Monomers

Natural polymer, chitosan was obtained from dried prawn shell waste through the preparation of chitin and was characterized. Thin film of chitosan was prepared by casting method from its 2% chitosan solution. Mechanical properties like tensile strength (TS), elongation at break (Eb) of chitosan film were studied. Five formulations were developed with 2-ethyl-2-hydroxy methyl-1,3-propandiol trimethacrylate (EHMPTMA), a trifunctional monomer and 2-ethylhexyl acrylate (EHA), a monofunctional monomer in the presence of photoinitiator Darocur-1664 (2%). The film was soaked in those monomer formulations in dissimilar soaking times and irradiated under UV-radiation at different radiation intensities for the improvement of the properties of chitosan film. The cured films were then subjected to various characterization tests like TS, Eb, polymer loading (PL), water absorbency, gel content etc. The formulation, containing 25% EHMPTMA and 73% EHA showed the best performance at 10th UV passes of UV radiation for 4 min soaking time.