Transformation of sulfaquinoxaline by chlorine and UV light in water: kinetics and by-product identification

Sulfaquinoxaline (SQX) is an antimicrobial of the sulfonamide class, frequently detected at low levels in drinking and surface water as organic micropollutant. The main goal of the present study is the evaluation of SQX reactivity during chlorination and UV irradiations which are two processes mainly used in water treatment plants. The SQX transformation by chlorination and UV lights (254 nm) was investigated in purified water at common conditions used for water disinfection (pH =?7.2, temperature =?25 °C, [chlorine] =?3 mg L^?1). The result shows a slow degradation of SQX during photolysis compared with chlorination process. Kinetic studies that fitted a fluence-based first-order kinetic model were used to determine the kinetic constants of SQX degradation; they were equal to 0.7?×?10^?4 and 0.7?×?10^?2 s^?1corresponding to the half time lives of 162 and 1.64 min during photolysis and chlorination, respectively. In the second step, seven by-products were generated during a chlorination and photo-transformation of SQX and identified using liquid chromatography with electrospray ionization and tandem mass spectrometry (MS-MS). SO₂ extrusion and direct decomposition were the common degradation pathway during photolysis and chlorination. Hydroxylation and isomerization were observed during photodegradation only while electrophilic substitution was observed during chlorination process.     

Precursors and nitrogen origins of trichloronitromethane and dichloroacetonitrile during chlorination/chloramination

The formation of trichloronitromethane (TCNM) and dichloroacetonitrile (DCAN) was investigated during chlorination and chloramination of 31 organic nitrogen (org-N) compounds, including amino acids, amines, dipeptides, purines, pyrimidones and pyrroles. Tryptophan and alanine generated the greatest amount of TCNM during chlorination process and asparagine and tyrosine yielded the highest amount of TCNM during chloramination process. Tryptophan, tyrosine, asparagine, and alanine produced more DCAN than other org-N compounds regardless of chlorination or chloramination. TCNM and DCAN formation was higher by chlorination than by chloramination. NH₂Cl:org-N molar ratios, reaction time, and pH affected N-DBPs formation in varying degrees. TCNM and DCAN yields were usually high during chloramination of tyrosine, asparagine, and methylpyrrole under the following reaction conditions: NH₂Cl:org-N molar ratios greater than 10, reaction time for 1 d, and at pH 7.2. NH₂Cl as a major nitrogen origin in TCNM and DCAN was confirmed via labeled ¹⁵N-monochloramine during chloramination of tyrosine, asparagine and methylpyrrole. In contrast, the majority of nitrogen in TCNM originated from glycine, and that in DCAN originated from pyrrole. Based on the intermediates identified by gas chromatography/mass spectrometry (GC/MS), a pathway scheme was proposed for TCNM and DCAN formation.     

4种脂肪多胺修饰硅胶对铅离子的吸附

为了合成高效铅离子吸附剂,了解其对铅离子的吸附规律。采用(3-氯丙基)三甲氧基硅烷(CPTS)架桥法,以硅胶(SG)为载体,乙二胺(EDA)、二乙烯三胺(DETA)、三乙烯四胺(TETA)和四乙烯五胺(TEPA)为表面修饰剂,合成了4种胺化硅胶,测定了它们的红外光谱、热重等性质以及对Cu2+、Zn2+和Pb2+的吸附能力。结果表明,4种胺化硅胶对Pb2+的吸附量均大于Cu2+和Zn2+的吸附量,其中DETA修饰硅胶对Pb2+的吸附量较高。4种胺化硅胶对Pb2+的吸附过程较好地符合拟二级动力学模型以及Langmuir和Scatchart等温吸附热力学模型,其对Pb2+吸附的速率常数、饱和吸附量以及吸附位点数由大到小的顺序一致,均为SG-DETASG-TEPASG-EDASG-TETA。4种胺化硅胶对Pb2+的吸附速率和吸附量呈现"奇数胺"增强效应,亲和常数则依次减小。阐明了脂肪多胺修饰硅胶对Pb2+的吸附规律,并进一步讨论了Scatchart和Langmuir热力学模型的统一性。     

Hg Reactions in the Presence of Chlorine Species: Homogeneous Gas Phase and Heterogeneous Gas-Solid Phase

Abstract

The kinetics of Hg chlorination (with HCl) was studied using a flow reactor system with an online Hg analyzer, and speciation sampling using a set of impingers. Kinetic parameters, such as reaction order (α), overall rate constant (k′ ), and activation energy (E _a), were estimated based on the simple overall reaction pathway. The reaction order with respect to C _Hg, k′, and E _a were found to be 1.55, 5.07 x 10^-2exp(-1939.68/T) [(μg/m³)^-0.55(s)^-1], and 16.13 [kJ/mol], respectively. The effect of chlorine species (HCl, CH₂Cl₂) on the in situ Hg capture method previously de-veloped²⁸ was also investigated. The efficiency of capture of Hg by this in situ method was higher than 98% in the presence of chlorine species. Furthermore, under certain conditions, the presence of chlorine enhanced the removal of elemental Hg by additional gas-phase oxidation.     

A second generation model for regional-scale transport/chemistry/deposition

The regional-scale transport, chemistry and deposition of acidifying compounds, photochemical oxidants, and their precursors are analyzed using a second-generation Eulerian model. The important atmospheric processes are incorporated using chemical, dynamical and thermodynamical parameterizations having sufficient detail to accommodate boundary layer-free troposphere exchange in cloudy and cloud-free environments, and in-cloud and below-cloud wet removal and chemistry. Forty-one species are considered, many of which are also present in the liquid-drop phases. In the regional scale transport, the advected species are NO, NO₂, SO₂, SO⁻²₄, O₃, HNO₃, NH₃, PAN, H₂O₂, HCHO, alkanes, C₂H₄, other olefins, aromatics, RCHO, ROOH, HNO₂, RONO₂ and RO₂NO₂. The model capabilities are illustrated by showing simulations in which non-precipitating clouds are present to absorb gas-phase species, chemically alter these, and then release them to the atmosphere.     

Stabilit?tsverhalten von ausgew?hlten anorganischen Spurenstoffen in Niederschlagsproben Stabilisierungsma?nahmen von H+, NH 4+ , PO 43? für Depositionsme?netze

Das Stabilit?tsverhalten von H⁺-, NH ₄ ⁺ -und PO ₄ ³⁻ -Ionen in Niederschlagsproben wurde unter verschiedenen Lagerungs-und Transportbedingungen untersucht. Ursachen für Ver?nderungen sind sowohlmikrobiologische als auchphysikalisch-chemische Prozesse. Die Unterdrückung mikrobieller Aktivit?ten gelingt im Rahmen vonDepositionsme?netzen mit konventioneller na?chemischer Analytik am besten durch Zusatz von Silberchloridpulver und gleichzeitiger Kühlung bei +4°C. Konzentrationsmessungen von unbehandelten Niederschlagsproben mit l?ngeren Expositions-und Transportzeiten müssen kritisch betrachtet werden.     

改性甘蔗渣对Cu2+和Zn2+的吸附机理

研究了均苯四甲酸二酐(PMDA)和乙二胺四乙酸二酐(EDTAD)改性甘蔗渣对重金属离子Cu2+和Zn2+的吸附性能,包括吸附动力学和吸附等温线。结果表明,改性后的甘蔗渣对重金属离子Cu2+和Zn2+的吸附容量有显著提高,对Cu2+和Zn2+吸附等温线均符合Langmuir方程,吸附为单分子层吸附。根据Langmuir方程,PMDA和EDTAD改性甘蔗渣对Cu2+的吸附量分别为60.21和33.45 mg/g,对Zn2+的吸附量分别是70.53和36.53 mg/g。两种改性甘蔗渣对两种金属离子的吸附在30 min内均可完成,用准二级吸附动力学方程模拟动力学过程得到较好的线性相关性。以EDTA溶液为洗脱剂对吸附Cu2+和Zn2+的改性甘蔗渣进行洗脱再生,再生的吸附剂可反复使用。     

金属铁去除水中Cr6+的影响因素研究

研究Fe/Cr6+比值和不同浓度的NO3-、Cl-和SO42-对金属铁去除Cr6+效果的影响.结果表明,金属铁对水中Cr6+有很好的还原去除效果;当金属铁的使用量为Cr6+量的1/2000时,铁对Cr6+的去除效果较差且易失去活性,而当金属铁的使用量为Cr6+量的8 000倍时,铁对Cr6+的去除效果较好且其活性的持续...     

Chlorination of dibenzofuran and dibenzo-p-dioxin vapor by copper (II) chloride

Dibenzofuran (DF) is formed from phenol and benzene in combustion gas exhaust streams prior to particle collection equipment. Subsequent chlorination at lower temperatures on particle surfaces is a potential source of chlorinated dibenzofuran (CDF). Gas streams containing 8% O₂ and approximately 0.1% DF vapor were passed through particle beds containing copper (II) chloride (0.5% Cu, mass) at temperatures ranging from 200 to 400 °C to investigate the potential for CDF formation during particle collection. Experiment duration was sufficient to provide an excess amount of DF (DF/Cu=3). The efficiency of DF chlorination by CuCl₂ and the distribution of CDF products were measured, with effects of temperature, gas velocity, and experiment duration assessed. Results of a more limited investigation of dibenzo-p-dioxin (DD) chlorination by CuCl₂ to form chlorinated DD (CDD) products are also presented.The efficiency of DF/DD chlorination by CuCl₂ was high, both in terms of CuCl₂ utilization and DF/DD conversion. Total yields of Cl on CDF/CDD products of up to 0.5 mole Cl per mole CuCl₂ were observed between 200 and 300 °C; this suggests that nearly 100% CuCl₂ was utilized, assuming a conversion of two moles of CuCl₂ to CuCl per mole Cl added to DD/DF. In a short duration experiment (DF/Cu=0.3), nearly 100% DF adsorption and conversion to CDF was achieved. The degree of CDF chlorination was strongly dependent on gas velocity. At high gas velocity, corresponding to a gas–particle contact time of 0.3 s, mono-CDF (MCDF) yield was largest, with yields decreasing with increasing CDF chlorination. At low gas velocity, corresponding to a gas–particle contact time of 5 s, octa-CDF yield was largest. DF/DD chlorination was strongly favored at lateral sites, with the predominant CDF/CDD isomers within each homologue group those containing Cl substituents at only the 2,3,7,8 positions. At the higher temperatures and lower gas velocities studied, however, broader isomer distributions, particularly of the less CDD/CDF products, were observed, likely due to preferential destruction of the 2,3,7,8 congeners.     

原位水解生成的羟基氧化铁凝聚吸附除磷效能与机制简

将不同摩尔比Fe³⁺与OH^-（[Fe³⁺]：[OH^-]=1：0、1：1、1：2和1：3）反应获得原位水解生成的羟基氧化铁（in situ FeO_xH_y）,研究了具有不同水解程度的羟基氧化铁对凝聚吸附除磷效能与机制。研究显示,In situ FeO_xH_y对磷的去除率随铁投量增大而升高,且均在中性pH范围内具有最佳除磷效果;在相同铁投量条件下,磷去除率随着[OH^-]：[Fe³⁺]的升高而降低;当体系碱度较低时（pH<6）,引入OH^-可促进Fe³⁺水解而提高除磷效果。4种羟基氧化铁均可在15 s内可快速吸附磷,且吸附过程符合准二级动力学模型;Freundlich模型均可很好地描述磷在4种羟基氧化铁表面的吸附行为。磷酸盐吸附后,In situ FeO_xH_y表面Zeta电位明显降低,且[Fe³⁺]：[OH^-]为1：0的羟基氧化铁降低最为显著。结合MINITEQ计算软件磷酸盐、铁盐形态分析结果显示,对于碱度较低的体系,通过投加一定量OH^-可促进Fe³⁺水解,进而使得其更易与水中H₂PO₄^-与HPO₄^2-结合,生成具有多核羟基的磷酸铁络合物,进而提高除磷效果。     

MCM-41介孔分子筛的合成及其对铜离子的吸附性能简

以微硅粉为硅源,CTAB和PEG-6000为模板剂,合成MCM-41介孔分子筛。采用XRD、N₂吸附-脱附曲线、FTIR以及TEM表征了其结构、比表面积、孔径分布及晶体形貌,并且以该样品为吸附剂,对含Cu²⁺的溶液进行了静态吸附实验。结果表明,以微硅粉为硅源成功合成了具有典型六方排列孔道结构的MCM-41,其比表面积为869.5 m²/g,孔容为0.97 cm³/g,平均孔径为3.3 nm;溶液pH为5~6时,MCM-41对Cu²⁺的去除效果最好;MCM-41对Cu²⁺的最大吸附吸附容量36.3 mg/g;MCM-41对Cu²⁺的吸附性能符合Langmuir吸附方程的特征。动力学研究表明,该过程符合准二级动力学模型。     

铁氧化物复合氧化铝催化臭氧化过程中溴酸盐的生成控制简

以市售活性炭、硅藻土和氧化铝小球为载体,考察了负载铁基活性组分对催化臭氧化过程中溴酸盐的控制情况,其中,铁基复合氧化铝小球体现出更好的溴酸盐还原特性和催化剂稳定性,证实催化剂中铁氧化物是溴酸盐得到有效控制的主要活性组分。进一步考察了铁基复合氧化铝小球催化臭氧化处理实际原水过程中对溴酸盐的生成控制,以及反应过程中溶解性有机碳（DOC）的去除情况。结果表明,与单独臭氧化相比,该催化剂既能有效去除水中的溶解性有机物,又能明显抑制溴酸盐的生成,反应50 h,其活性并没有明显下降。催化剂失活主要归因于吸附位点数量的下降,可以通过负载铁氧化物来实现催化剂的再生。     

液/固体系中硅藻土对Pb2+和Cd2+的吸附机制

为了提高硅藻土在重金属废水处理上的应用水平,采用静态吸附实验考察了液/固体系中硅藻土对Pb2＋、Cd2＋的吸附影响因素、吸附等温线和吸附动力学属性。结果表明,随着投加量的减少,离子初始浓度的提高,pH值的增大,吸附作用时间的延长,硅藻土对Pb2＋、Cd2＋吸附量不断上升;硅藻土对Pb2＋、Cd2＋的等温吸附都符合Langmuir模型,硅藻土对Pb2＋、Cd2＋最大吸附量分别为10.428 mg/g和7.916 mg/g,硅藻土对Pb2＋具有更好的吸附能力;Pb2＋具有较低的水合自由能,更容易脱去水膜与硅藻土孔道内的活性基团发生吸附作用;双常数扩散方程可以很好地描述硅藻土对Pb2＋、Cd2＋的吸附动力学属性,硅藻土对Cd2＋有较快的吸附速率。     

A2/O-MBR工艺处理低负荷污水并回用

将A²/O生物处理单元与MBR相结合构建了的处理能力为2 000 m³/d的A²/O-MBR工艺,并应用于缺水地区校园生活污水的处理与回用。该系统运行稳定,运行阶段的实验结果表明,在进水COD为100~200 mg/L、NH₄⁺-N为19~33 mg/L、TN为25~43 mg/L、TP为3~5 mg/L和低碳氮比的情况下,出水水质优于《城市污水再生利用城市杂用水水质》 (GB/T 18920-2002) 的要求,且全部用于杂用及校园绿化等。经分析该工艺运行成本为0.96 元/m³,每年可节省自来水73万t,获得较好的环境效益与经济效益。     

Kinetics of the oxidation of hydrogen sulfite by hydrogen peroxide in aqueous solution:: ionic strength effects and temperature dependence

Conductometry was used to study the kinetics of the oxidation of hydrogen sulfite, HSO⁻₃, by hydrogen peroxide in aqueous non-buffered solution at the low concentration level of 10⁻⁵–10⁻⁶ M, typically found in cloud water. The kinetic data confirm that the rate law reported for the pH range 3–6 at higher concentration levels, rate=k_H·[H⁺]·[HSO⁻₃]·[H₂O₂], is valid at the low concentration level and at low ionic strength I_c. At 298 K and I_c=1.5×10⁻⁴ M, third-order rate constant k_H was found to be k_H=(9.1±0.5)×10⁷ M⁻² s⁻¹. The temperature dependence of k_H led to an activation energy of E_a=29.7±0.9 kJ mol⁻¹. The effect of the ionic strength (adjusted with NaCl) on rate constant k_H was studied in the range I_c=2×10⁻⁴–5.0 M at pH=4.5–5.2 by conductometry and stopped-flow spectrophotometry. The dependence of k_H on I_c can be described with a semi-empirical relationship, which is useful for the purpose of comparison and extrapolation. The kinetic data obtained are critically compared with those reported earlier.     

Synthesis of polychlorinated [14C]alkanes (PCA) of high specific activity

The synthesis of certain ¹⁴C-labelled polychlorinated alkanes is described. The compounds used as starting material were [1-¹⁴C]lauric acid, [1-¹⁴C]hexadecane and [U-¹⁴C]palmitic acid. The carboxylic acids were reduced with lithium aluminium hydride. The alcohol obtained was treated with triphenylphosphine dichloride which gave the corresponding 1-chloroalkane. The chlorination of the alkanes was performed in tetrachloromethane by use of sulphuryl chloride with benzoyl peroxide or UV-light as initiators. Three mixtures of polychlorinated dodecanes (45.9%, 55.9% and 68.5% chlorine) and two polychlorinated hexadecanes (34.1% and 69% chlorine) were synthesized. The products of higher chlorine content prepared were only available via the photoinduced chlorination.     

Effect of Ca2+-ions on the absorption of Pb2+, Cu2+, Cd2+ and Zn2+ by humic substances

Distribution coefficients for the sorption of Pb²⁺, Cu²⁺, Cd²⁺ and Zn²⁺ by peat were determined as a function of the Ca²⁺-content of peat as well as of the Ca²⁺-concentration in the solution. The amount of heavy metal ions taken up was measured for Cu²⁺, Cd²⁺ and Zn²⁺ by atomic absorption spectrometry and for Pb²⁺ by using Pb-212 as a radioactive tracer.The results show that the distribution coefficients of the heavy metal ions increase, if one increases the initial ratio of the $\text{Ca}{}^{\mathrm{2+}}\text{H}{}^{\mathrm{+}}\text{-}\text{ions}$ in the peat phase. The distribution coefficients for the heavy metal ions decrease, however, if - at constant initial Ca²⁺-content of the peat - the Ca²⁺-concentration of the solution is increased.     

一体式A/O反应器中不同碳硫比对除碳脱臭效率的影响

在污水处理领域同步除碳脱臭研究一直是个难题,本实验开发了一种新型同步除碳脱臭一体式A/O反应器,研究了该一体式A/O反应器处理不同碳硫比有机废水时的同步除碳脱臭功能。结果表明,碳硫比为30∶1时,即进水SO24-浓度为133 mg/L,该反应器总COD去除率可达到95%。在进水SO24-浓度不大于400 mg/L时,中间产物臭气硫化氢气可以完全去除,实现了同步除碳脱臭的功能,减少了在有机废水处理过程中的大量臭气的排放。微生物学角度分析,表明污泥中含有大量的硫细菌。     

镉溶液污染黏土微观结构演化规律

镉溶液在压实黏土中迁移会引起黏土微观结构的变化。通过一系列扫描电子显微镜与低温氮吸附实验,观察了镉溶液污染黏土的表面微观形貌与孔隙结构的演化规律。扫描电子显微镜观察结果显示,受镉溶液污染严重的土柱上表面孔隙明显,土颗粒之间主要以点-点排列方式为主;而受镉溶液污染较弱的下表面,土颗粒之间主要以片-片状排列为主。低温氮吸附实验结果表明,Z=0 cm、Z=10 cm、Z=20 cm、Z=30 cm处,污染黏土吸附量分别为682.65、631.72、583.25和523.36 cm3/g。随土柱中土层深度的增大,黏土颗粒间微孔增多,二次孔减少,孔隙体积与比表面积减小。镉溶液污染黏土孔隙主要集中在10 nm以下。     

Ambient TSP concentration and dustfall in major cities of China: Spatial distribution and temporal variability

Based on environmental monitoring data in 93 major cities and meteorological records at 398 weather stations in China from 1981 to 2007, total suspended particle (TSP) concentration, the intensity of dustfall, and sand and dust storm frequency (F_d) were analysed. During the past 27 years, the annual average TSP concentration (C_TSP) in 93 cities was 402 μg m^?3. Annual average C_TSP decreased from the north to the south and from inland to the coast areas with a peak value of 628.8 μg m^?3 in Lanzhou. In the 1980s, 1990s and 2000s, annual average C_TSP was 628.7, 319.2, and 250.1 μg m^?3, respectively. Annual average intensity of dustfall (I_d) was 240.5 t km^?2 a^?1, decreased from northern to southern China and from inland to the coast areas with the maximum value of 717.2 t km^?2 a^?1 in Baotou. In the 1980s, 1990s and 2000s, annual average I_d was 334.8, 220.9, 146 t km^?2 a^?1 respectively. Annual average I_d in the Loess Plateau region was commonly higher than 200 t km^?2 a^?1. The annual average F_d decreased from arid regions in northwestern China to humid areas in southeastern China with two sand and sand storm centers existing in Xinjiang Taklamakan Desert and western Inner Mongolia. The annual average F_d in the 1980s, 1990s, 2000s was 16, 8, 6 days respectively, decreased steadily from 18 days in 1981–5 days in 2007. Annual average I_d had a positive linear relation to annual average C_TSP (R² = 0.96). Annual average F_d had a positive relation with annual average C_TSP (R² = 0.97) as well as annual average I_d (R² = 0.94). TSP was the chief pollutant influencing Air Pollution Index (API) in northern China in spring and winter seasons. Sand and dust storm might be a major factor affecting the temporal variability and spatial distribution of TSP and dustfall in China.