Acclimatisation to nitrilotriacetic and in the activated sludge process

The period of acclimatisation prior to the biodegradation of nitrilotriacetic acid in an activated sludge pilot plant was studied in a series of experiments. The effects of low and high influent heavy metals concentrations upon acclimatisation are reported.     

Enhanced adsorptive removal of Cr(III) from the complex solution by NTA-modified magnetic mesoporous microspheres

Environmental Science and Pollution Research - The Fe3O4@nSiO2@mSiO2/NTA (FNMs-NTA) was prepared by grafting magnetic mesoporous microspheres with nitrilotriacetic acid (NTA) and applied as an...     

Occurrence of aminopolycarboxylates in the aquatic environment of Germany

Aminopolycarboxylic acids, such as ethylenediaminetetraacetic acid (EDTA), nitrilotriacetic acid (NTA), diethylenetriaminepentaacetic acid (DTPA), 1,3-propylenediaminetetraacetic acid (1,3-PDTA), beta-alaninediacetic acid (beta-ADA), and methylglycinediacetic acid (MGDA), are used in large quantities in a broad range of industrial applications and domestic products in order to solubilize or inactivate various metal ions by complex formation. Due to the wide field of their application, their high polarity and partly low degradability, these substances reach the aquatic environment at considerable concentrations (in the microg/L-range) and have also been detected in drinking water. This review evaluates and summarizes the results of long-term research projects, monitoring programs, and published papers concerning the pollution of the aquatic environment by aminopolycarboxylates in Germany. Concentrations and loads of aminopolycarboxylates are presented for various types of water including industrial and domestic waste waters, surface waters (rivers and lakes), raw waters, and drinking waters.     

Occurrence and behavior of wastewater indicators in the Santa Ana River and the underlying aquifers.

The occurrence and behavior of wastewater indicator compounds in the Santa Ana River (SAR) water and the underlying aquifer recharged by the SAR has been studied. The SAR contains a high proportion of tertiary treated wastewater effluents, up to 100% during summer and fall. The following water quality parameters were quantified: four specific wastewater indicator compounds, ethylene diaminetetraacetic acid (EDTA), nitrilotriacetic acid (NTA), a naphthalene dicarboxylate (NDC) isomer, alkylphenol polyethoxy carboxylates (APECs), and selected haloacetic acids (HAAs), nitrate, dissolved oxygen (DO), DOC, total carbohydrate, and phenolic substances. Statistical analysis indicated that normal distribution was adequate to describe the probability distribution of the constituents in most cases. In the river, the concentrations of wastewater indicator compounds decreased as the fraction of storm runoff increased. EDTA and NDC were detected in a monitoring well near the river and in two production wells 1.8 and 2.7 km down gradient with little apparent attenuation. By contrast, NTA, APECs, bromochloro- and dibromoacetic acids appeared to be attenuated significantly during infiltration of river water and groundwater transport.     

Polyelectrolyte enhanced ultrafiltration (PEUF) for the removal of Cd(II): effects of organic ligands and solution pH

This study focused on the effects of pH and organic ligands, namely ethylenediaminetetraacetic acid (EDTA), nitrilotriacetic acid (NTA), and citric acids, on the removal and recovery of Cd(II) in polyelectrolyte enhanced ultrafiltration (PEUF). Polyethylenimine (PEI), which can bind with both positively charged metal ions by coordination bonding and negatively charged ligand-metal complexes by charge attraction, was employed as a chelating polymer. The removal and recovery of Cd species was greatly dependent on the chemistry of organic ligands according to solution pH, particularly being related to the distribution of Cd-ligand complexes at different pH levels. In the presence of EDTA, the dominant Cd species are negatively charged Cd(EDTA)(2-) and CdH(EDTA)(-) over the range of pH levels investigated, interacting with PEI via electrostatic attraction and being less pH dependent. On the other hand, the pH effects of both NTA and citric acid systems are similar to that for the system without organic ligands. This was associated with the fact that free Cd ions were predominant at the acidic pH range in both NTA and citric acid systems.     

An evaluation of the green chelant EDDS to enhance the stability of hydrogen peroxide in the presence of aquifer solids

Hydrogen peroxide is a widely used in situ chemical oxidation reagent which relies on catalysts to generate the suite of reactive species that are required to aggressively remediate contaminated soils and groundwater. In the subsurface environment these catalysts are usually transition metals that are added to the injected solution, or are naturally occurring. Chelating agents are widely used to maintain an adequate dissolved transition metal concentration in near-neutral pH conditions; however, they can also be used to improve the persistence of H(2)O(2) in situations when the aquifer solids have sufficient transition metal content. Ethylenediamine tetraacetic acid (EDTA) and nitrilotriacetic acid (NTA) have been considered to be the most effective chelants and therefore are the most widely used. While previous research efforts have focused on the chelating agent efficiency, the long-term fate of these chelants in the natural subsurface environment is a concern since both EDTA and NTA are non-readily biodegradable. The focus of this investigation was to evaluate the potential of using the environmentally friendly or green chelating agent ethylenediaminedisuccinate (EDDS) as an alternative to EDTA or NTA to suppress the catalytic activity of naturally-occurring transition metals. A series of batch reactor and column experiments were performed using five different aquifer materials and the results demonstrate that EDDS has a comparative chelating efficiency to that of EDTA. The addition of EDDS was able to reduce the H(2)O(2) decomposition rates in the presence of the aquifer materials used in this investigation by 24-97% in well-mixed batch systems, and by 20% and 38% in the column trials where H(2)O(2) was detected in the effluent.     

Formation of aerobic granules in the presence of a synthetic chelating agent

This paper examines the development of aerobic granular sludge in the presence of a synthetic chelating agent, nitrilotriacetic acid (NTA), in sequencing batch reactors (SBR). The growth of seed sludge at 0.26 mM, 0.52 mM and 1.05 mM of NTA was found to be significantly lower as compared to that in the absence of NTA. Aerobic granulation was significantly enhanced in the three SBRs (R2, R3 and R4), which were fed with 0.26 mM, 0.52 mM and 1.05 mM of NTA as a co-substrate, in comparison to the acetate-alone fed SBR (R1). After 2 months of operation, the mean diameter of the biomass stabilized at 0.35 mm in R1 (acetate alone), as compared to 2.18 mm in R4 (1.05 mM NTA+acetate). NTA degradation was established in SBRs, with almost complete removal during the SBR cycle. Batch experiments also showed efficient degradation of NTA by the aerobic granules.     

Chelate assisted phytoextraction of heavy metals from soil. Effect, mechanism, toxicity, and fate of chelating agents

The low-cost, plant-based phytoextraction technique has often been described as a promising technique to remediate heavy metal contaminated agricultural land. The application of chelating agents has shown positive effects in increasing the solubility of heavy metals in soil and therefore in enhancing phytoextraction. This paper gives an overview of the chelating agents applied in recent studies. Various synthetic aminopolycarboxylic acids, such as ethylene diamine tetraacetic acid, and natural ones such as, ethylene diamine disuccinate and nitrilotriacetic acid, are described. Additionally, results of the application of natural low molecular weight organic acids, such as citric and tartaric acid are given. The effectiveness of these different chelating agents varies according to the plant and the heavy metals used. Furthermore, a focus is laid on the chelating agents fate after application and on its toxicity to plants and soil microorganisms, as well as it degradation. The rate of degradation is of great importance for the future of chelate assisted phytoextraction as it has a direct impact on the leaching probability. An effective prevention of leaching will be crucial for the acceptance and the economic breakthrough of enhanced phytoextraction, but a satisfactory solution to this key issue has so far not been found. Possibly further experiments in the field of enhanced phytoextraction will be able to solve this major problem, but over decades various greenhouse experiments and recently field experiments have resulted in different observations. Therefore, it is questionable if further research in this direction will lead to a promising solution. Phytoextraction has possibly reached a turning point in which it should distance itself from chelate assisted phytoextraction and focus on alternative options.     

Removal of metal ions from the complexed solutions in fixed bed using a strong-acid ion exchange resin

Fixed bed removal of equimolar metal ions (Co²⁺, Ni²⁺, Mn²⁺, Sr²⁺) from aqueous solutions using a strong-acid resin was examined. The solution contained a water-soluble complexing agent including ethylenediaminetetraacetic acid, nitrilotriacetic acid, and citric acid. Experiments were performed under different solution pH and molar concentration ratios of complexing agent to the total metals. It was shown from batch studies that the equilibrium exchange of metals and the resin mainly depended on solution pH, and partly on the type of complexing agent used. A mass transfer model was proposed to describe the breakthrough curves of the resin bed, which contained two parameters (τ and k) estimated from the observed breakthrough data. The calculated breakthrough curves agreed well with the measured ones (standard deviation <6%). In fixed bed tests at low pH (=2), the type of complexing agent had little effect on the breakthrough data. For a given complexing agent, the metal with a larger overall formation constant (K_f) showed a smaller exchange capacity. For a given metal ion, the complexing agent with a larger K_f also revealed a smaller exchange capacity.     

Sequential extraction analysis of heavy metals in sediments of variable composition using nitrilotriacetic acid to counteract resorption

Artificial sediments were made that contained variable amounts (up to 20% by weight) of feldspar, calcite, Fe-oxide or organic matter. Analysis of samples spiked with Pb and Zn in the presence and absence of nitrilotriacetic acid (NTA) showed that 400 mg l(-1) of chelating agent greatly reduced or eliminated sorption in each case. Further study showed that this NTA concentration did not cause significant mineral dissolution. Resorption during sequential extraction analysis of artificial sediments is indicated by the fact that with NTA, levels of metals are higher in the first step and lower during subsequent steps, compared with levels obtained without NTA. However, the addition of 400 mg l(-1) of NTA to each extracting solution in the sequence appears to be effective for counteracting resorption in feldspathic, calcareous, ferruginous and carbonaceous sediments.     

A new method to study biodegradation kinetics of organic trace pollutants by activated sludge

A reliable prediction of the behaviour of organic trace compounds in activated sludge plants requires an accurate input of the biodegradation kinetics. Often these kinetics are extrapolated from the results of standardised biodegradation tests. However, these tests generally are not designed to yield kinetic information and do not reflect the conditions in activated sludge plants. To overcome these problems a new test method was developed which is referred to as a 'by-pass' test. The test methodology is explained and examples are given for three compounds: the C(12)-homologue of linear alkylbenzene sulfonate, nitrilotriacetic acid and toluene. More experience with the test is required, particularly with respect to selection of the proper test settings, which are compound related. The test is a suitable tool in a research environment, for example to investigate the effect of plant operational parameters on the biodegradation kinetics.     

Chelating agent-assisted electrokinetic removal of cadmium, lead and copper from contaminated soils

An integrated experimental program was conducted to remove Cd, Pb and Cu from contaminated soil. The chelate agents nitrilotriacetic acid (NTA), diethylenetriamine pentaacetic acid (DTPA) and ethyleneglycol tetraacetic acid (EGTA) were used as washing solutions under different pH conditions and concentrations. Results showed that the extraction efficiency for Cd in decreasing order was NTA > EGTA > DTPA, while for Pb and Cu it was DTPA > NTA > EGTA. The use of higher chelate concentrations did not necessarily result in greater extraction efficiency. Electrokinetic remediation was applied by conditioning anolyte-catholyte pH to neutral values in order to avoid any potential alterations to the physicochemical soil properties. The removal efficiency for Cd was 65-95%, for Cu 15-60%, but for Pb was less than 20%. The phytotoxicity of the treated soil showed that the soil samples from the anode section were less phytotoxic than the untreated soil, but the phytotoxicity was increased in the samples from the cathode section.     

类Fenton反应对偶氮染料橙黄II的脱色研究

以橙黄II染料溶液为研究对象,通过正交实验确定了Fe-NTA/H2O2构成的类Fenton反应中各影响因子的最佳操作条件为:[H2O2]=20 mmol/L,[Fe-NTA]=2.5 mmol/L,pH=3。同时考察了反应时间、溶液pH值、H2O2浓度、Fe-NTA浓度对脱色效率的影响。实验表明脱色反应在30 m in内基本完成,类Fenton试剂能在较宽的pH范围内保持较好的脱色效果,而且在pH=6时,类Fenton试剂比传统Fenton试剂的脱色效率提高约75%。增加双氧水浓度可以提高橙黄II溶液脱色率,但超过20 mmol/L后效果提高不明显。在0.5~2.5 mmol/L的范围内,Fe-NTA浓度对脱色效果的影响不显著。     

Sequential extraction analysis of heavy metals using a chelating agent (NTA) to counteract resorption

The geochemical partitioning of Pb, Ni and Zn in contaminated quartz-rich sediment and soil samples was characterized by sequential extraction analysis in the presence and absence of nitrilotriacetic acid (NTA). With NTA, levels of metals recovered are higher in the earlier steps and lower in the later steps of the procedure. This suggests that post-extraction resorption is effectively counteracted by chelation, thereby improving the accuracy of the method. An NTA concentration of 200 mg liter(-1) appears to be sufficient for counteracting resorption without causing significant dissolution of non-targeted phases in the samples studied. However, experiments using reference materials spiked with solutions containing Pb, Ni, Cu and Zn suggest that resorption will remain a problem when large amounts of strong sorbents such as organic matter are present. The results also show that although post-extraction resorption does occur in the absence of NTA, the magnitude of resorption is small (<20 to 30% of the summed total of metal present in the sample) in quartz-rich sediments.     

Remediation of toxic metal contaminated soil by washing with biodegradable aminopolycarboxylate chelants

Ex situ soil washing with synthetic extractants such as, aminopolycarboxylate chelants (APCs) is a viable treatment alternative for metal-contaminated site remediation. EDTA and its homologs are widely used among the APCs in the ex situ soil washing processes. These APCs are merely biodegradable and highly persistent in the aquatic environments leading to the post-use toxic effects. Therefore, an increasing interest is focused on the development and use of the eco-friendly APCs having better biodegradability and less environmental toxicity. The paper deals with the results from the lab-scale washing treatments of a real sample of metal-contaminated soil for the removal of the ecotoxic metal ions (Cd, Cu, Ni, Pb, and Zn) using five biodegradable APCs, namely [S,S]-ethylenediaminedisuccinic acid, imminodisuccinic acid, methylglycinediacetic acid, DL-2-(2-carboxymethyl) nitrilotriacetic acid (GLDA), and 3-hydroxy-2,2′-iminodisuccinic acid. The performance of those biodegradable APCs was evaluated for their interaction with the soil mineral constituents in terms of the solution pH and metal-chelant stability constants, and compared with that of EDTA. Speciation calculations were performed to identify the optimal conditions for the washing process in terms of the metal-chelant interactions as well as to understand the selectivity in the separation ability of the biodegradable chelants towards the metal ions. A linear relationship between the metal extraction capacity of the individual chelants towards each of the metal ions from the soil matrix and metal-chelant conditional stability constants for a solution pH greater than 6 was observed. Additional considerations were derived from the behavior of the major potentially interfering cations (Al, Ca, Fe, Mg, and Mn), and it was hypothesized that use of an excess of chelant may minimize the possible competition effects during the single-step washing treatments. Sequential extraction procedure was used to determine the metal distribution in the soil before and after the extractive decontamination using biodegradable APCs, and the capability of the APCs in removing the metal ions even from the theoretically immobilized fraction of the contaminated soil was observed. GLDA appeared to possess the greatest potential to decontaminate the soil through ex situ washing treatment compared to the other biodegradable chelants used in the study.     

The use of NTA and EDDS for enhanced phytoextraction of metals from a multiply contaminated soil by Brassica carinata

The potential of nine different species to grow in the presence of metals (As, Cd, Cu, Pb and Zn) and to accumulate them in the shoots was assessed for each metal separately by germination and root length tests, and successively by hydroponic experiments. Of the nine species tested, Brassica carinata was the species that accumulated the highest amounts of metals in shoots without suffering a significant biomass reduction. To further evaluate the potential of B. carinata for chelant-enhanced phytoextraction of a natural, multiply metal-polluted soil (As, Cd, Cu, Pb and Zn), both hydroponic and pot experiments were carried out with nitrilotriacetic acid (NTA) or (S,S)-ethylenediamine disuccinic acid (EDDS) as complexing agents. The hydroponic study with solutions containing the five metals together showed that accumulation of Cd, Cu, Pb and Zn in shoots was higher following EDDS addition compared to NTA. EDDS was more effective than NTA in desorbing Cu, Pb and Zn from the soil, whereas As and Cd were poorly extracted. B. carinata plants were grown for 4 weeks in the multiply metal-contaminated soil and then the soil was amended with 5 mmol kg(-1) NTA or EDDS. All plants were harvested 1 week after amendment. In comparison to NTA, EDDS was more effective in enhancing the concentrations of Cu, Pb and Zn in B. carinata shoots (2- to 4-fold increase compared to the control). One week after chelant addition, the DTPA-extractable metal concentrations in the polluted soil were lower in the EDDS treatment in comparison with the NTA amendment. Even though B. carinata showed a reduced growth and a relatively low metal uptake, it demonstrated the ability to survive and tolerate the presence of more metals simultaneously.     

Effect of EDTA and NTA on cadmium distribution and translocation in Pennisetum purpureum Schum cv. Mott

The primary objective of this research was to investigate the cadmium (Cd) distribution in Pennisetum purpurem (Napier grass) in the presence of 30 mg/L of Cd and different types and concentrations of chelating agents (ethylenediaminetetraacetic acid disodium dihydrate (EDTA), nitrilotriacetic acid (NTA), and EDTA-NTA mixtures). Plant samples were collected every 15 d during a 105-d experimental period. Accumulation of Cd in each part of the plant was determined using atomic absorption spectrometer (AAS), and the distribution of Cd was determined by laser ablation inductively coupled plasma mass spectrometer (LA-ICP-MS) and synchrotron radiation micro X-ray fluorescence (SR-micro-XRF). The highest concentrations of Cd accumulation of 889?±?53 mg kg^?1 in the underground part (roots) and 265?±?26 mg kg^?1 in the aboveground part (stems and leaves) in the presence of 1:1 M ratio of Cd:EDTA after 30 d of exposure were observed. Plants grown in the presence of either NTA or EDTA-NTA mixtures showed significant lower Cd accumulation levels. The LA-ICP-MS analysis showed that Cd was primarily accumulated in the aboveground part (stems and leaves), especially in the xylem and intercalary meristem. In addition, translocation factor was very low. Thus, P. purpurem could be considered as a candidate plant for cadmium phytostabilization.

     

On the uptake and release of zinc (65Zn) in the growing alga Selenastrum capricornutum Printz

A Zn- and pH-buffered medium was used to study the accumulation of Zn in batch-cultured algae (Selenastrum capricornutum Printz.). All experiments were carried out using (65)Zn radiotracers, which were measured by gamma-ray spectrometry. Zinc was applied in the presence of nitrilotriacetic acid (NTA), leading to free Zn(2+) concentrations ranging from 4.2 x 10(-11) to 1.6 x 10(-7) mol litre(-1). During the 75-h experiments, the rates of Zn influx and efflux were determined, the latter with full consideration for algal growth rates. Algal growth stopped completely at a free Zn(2+) concentration of 1.6 x 10(-8) mol litre(-1). Initial Zn binding was determined and, based on free Zn(2+) concentrations, presented by the apparent dissociation constant K(diss) and capacity C as 4.6 x 10(-9) mol litre(-1) and 19.8 x 10(6) mol gDW(-1), respectively. The rate constant of Zn efflux could be calculated as a constant 0.021 +/- 0.003 h(-1), irrespective of the Zn concentrations applied. The rates of Zn influx were expressed by the V(max) and K(M) values as 3.3 x 10(-10) mol gDW(-1) s(-1) and 6.3 x 10(-9) mol litre(-1), respectively. These values, which are based on applied free Zn(2+) concentrations, are compatible with the operation of a high-affinity low-concentration carrier mechanism. The results suggest that, under the conditions applied, free Zn(2+) may be the most relevant Zn species for Zn uptake; furthermore, relative growth rate may be regarded as a relatively sensitive signal for Zn stress circumstances.     

Identification of relevant micropollutants in Austrian municipal wastewater and their behaviour during wastewater treatment

The European Union has defined environmental quality standards (EQSs) for surface waters for priority substances and several other pollutants. Furthermore national EQSs for several chemicals are valid in Austria. The study investigated the occurrence of these compounds in municipal wastewater treatment plant (WWTP) effluents. In a first screening of 15 WWTPs relevant substances were identified, which subsequently were monitored in 9 WWTPs over 1 year (every 2 months). Out of 77 substances or groups of substances (including more than 90 substances) 13 were identified as potentially relevant in respect to water pollution and subjected to the monitoring, whereas most other compounds were detected in concentrations far below the respective EQS for surface waters and therefore not further considered. The preselected 13 compounds for monitoring were cadmium (Cd), nickel (Ni), copper (Cu), selenium (Se), zinc (Zn), diuron, polybrominated diphenyl ethers (PBDEs), di(ethyl-hydroxyl)phthalate (DEHP), tributyltin compounds (TBT), nonylphenoles (NP), adsorbable organic halogens (AOX) and the complexing agents ethylenediaminetetraacetic acid (EDTA) as well as nitrilotriacetic acid (NTA). In the effluents of WWTPs the concentrations of the priority substances Cd, NP, TBT and diuron frequently exceeded the respective EQS, whereas the concentrations for DEHP and Ni were below the respective EQS. The effluent concentrations for AOX, EDTA, NTA, Cu, Se and Zn frequently are in the range or above the Austrian EQS for surface waters. Besides diuron and EDTA all compounds are removed at least partially during wastewater treatment and for most substances the removal via the excess sludge is the major removal pathway. For the 13 compounds which were monitored in WWTP effluents population equivalent specific discharges were calculated. Since for many compounds no or only few information is available, these population equivalent specific discharges can be used to assess emissions from municipal WWTPs to surface waters as well as to make a first assessment of the impact of a discharge on surface waters chemical status. Comparing discharges and river pollution on a load basis, the influence of diffuse sources becomes obvious and therefore should also be taken into consideration in river management.     

Optimization of the coating layer for the measurement of ammonia by diffusion denuders

The performance of citric acid, oxalic acid and phosphorous acid as denuder coating layers for the determination of atmospheric ammonia have been studied by means of laboratory and field tests. The parameters evaluated during the study include: collection efficiency, selectivity of the coating layer, stability of the reaction product, operative capacity and stability of the coating layer. The results of this study show that phosphorous acid is a suitable coating layer for a denuder line intended to determine both gaseous ammonia and particulate ammonium in the atmosphere. It has been found that the citric acid coating suffers from an insufficient strength of the bond between collected ammonia and the coating layer, which causes a release of the collected ammonia both towards the air flow and towards the active sites of the denuder glass. The performance of oxalic acid was very good in the determination of gaseous ammonia, but this coating showed to be unsuitable for denuder sampling lines which are intended also for the determination of atmospheric ammonium. The volatilisation of oxalic from the denuder surface, in fact, causes a displacement of nitrate from the Teflon filter and an excess of nitrate ion on the back-up filter.Phosphorous acid-coated denuders were added to the sampling line employed in the EMEP station of Montelibretti. Reliable and interesting results were obtained, which allowed us to detect the presence of gaseous ammonia adsorbed on atmospheric particles.