内电解-Fenton 氧化-膜生物反应器处理腈纶废水

采用内电解-Fenton 氧化-序批式膜生物反应器组合工艺处理腈纶废水.结果表明,在进水Ph 值为3、内电解反应时间2h、H₂O₂ 浓度1500 mg/L、Fe²⁺浓度600mg/L、Fenton 反应时间2h 的条件下,内电解-Fenton 组合工艺对COD 的去除率为72%,进水COD 从1328mg/L下降到369mg/L,废水BOD₅/COD 从0.14 上升到0.33,CN-从8.6mg/L 下降到0.215mg/L,提高了废水可生化性,为后续的生物处理创造了良好的条件.出水采用序批式膜生物反应器处理,在停留时间20h、缺氧搅拌90min、好氧120min 条件下,COD 去除率为80%,NH₄₊-N 去除率95%,BOD₅ 去除率92.6%,CN-去除率90.7%.最终出水COD、BOD5、NH4+-N、CN-、SS 分别为61,9.3,2.55,0.02,13mg/L     

UBF-AOMBR处理垃圾渗滤液中试

采用UBF(厌氧复合床反应器)-AOMBR(缺氧/好氧膜生物反应器)工艺处理垃圾渗滤液,考察该工艺组合的可行性并作为该领域工程应用的参考。试验结果表明:当进水渗滤液COD浓度10000mg/L左右,NH4+-N浓度2000mg/L左右时,出水COD浓度为1000mg/L,出水NH4+-N浓度为50～100mg/L,COD总去除率>90%,NH4+-N去除率95%左右。UBF最大COD容积负荷为6～7kg/(m3.d)。pH、碱度、回流比是影响系统稳定运行的重要因素。当AOMBR系统MLSS>10000mg/L时,膜污染严重,采用酸、碱、NaClO溶液清洗后膜性能恢复为原来的75%左右。     

一体化膜生物反应器处理低C/N污水试验研究

研究一体化连续流间歇曝气膜生物反应器(IMBR)处理低C/N城市污水的工艺效能。试验结果表明:反应器在曝气2 h、搅拌2 h的运行模式下,对COD、NH4+-N、TN和SS的平均去除率分别达到了87%,83.4%,75.4%和97.81%,各出水质量浓度平均值分别为17.5,4.59,7.63和2 mg/L,出水水质达到了GB/T18920-2002《城市污水再生利用城市杂用水水质》标准。     

中空膜生物反应器处理港口含油废水的中试研究

采用中试规模的中空膜生物床处理混凝沉淀后港口含油废水。进水COD浓度为245⁵44mg/L,当HRT=4h时,出水COD平均浓度为146.5mg/L,平均去除率为64.2%;当HRT=8h时,出水COD平均浓度为133.4mg/L,平均去除率为64.6%。采用活性炭对MBR出水进行深度处理,处理后出水的COD浓度均小于130mg/L,NH4+-N浓度为1.2544mg/L,当HRT=4h时,出水COD平均浓度为146.5mg/L,平均去除率为64.2%;当HRT=8h时,出水COD平均浓度为133.4mg/L,平均去除率为64.6%。采用活性炭对MBR出水进行深度处理,处理后出水的COD浓度均小于130mg/L,NH4+-N浓度为1.2⁴.1mg/L,石油类污染物浓度为0.44.1mg/L,石油类污染物浓度为0.4⁰.9mg/L。MBR稳定运行期间,膜组件的操作负压稳定在0.03MPa以下,远低于化学清洗时的操作负压控制标准0.05Mpa。     

移动床膜生物反应器同步硝化反硝化特性

采用挂膜填料代替传统膜生物反应器(MBR)的活性污泥,构建一种新型的移动床膜生物反应器 (MBMBR),考察其处理模拟生活污水的效果及同步硝化反硝化(SND)特性.结果表明,移动床膜生物反应器运行67 d,对模拟生活污水表现出良好的去除有机物及同步硝化反硝化能力.进水COD浓度为573.5～997.7 mg/L时,膜出水COD去除率为88.3%～99.2%.进水氨氮浓度为45.5～99.2 mg/L时,膜出水氨氮去除率为72.1%～99.8%,总氮去除率为62.0%～96.3%.批式实验结果表明,生物膜去除总氮的最佳溶解氧浓度为1 mg/L,其中氨氮和总氮去除率分别为100%和60%.生物膜系统内可能存在好氧反硝化现象.DO为3 mg/L且有机碳源充足时,生物膜总氮去除率为99.0%,SND率达到99.8%.扫描电镜对生物膜的观察发现生物膜内部存在着明显的孔隙,有利于溶解氧和有机基质从外界向生物膜内部传递.     

UASB-膜生物反应器处理抗生素废水的研究

采用UASB-膜生物反应器对抗生素废水进行处理研究。结果表明,UASB具有很强的抗冲击能力,当UASB和膜生物反应器的容积负荷分别为10.9kgCOD/m3·d和4.62kgCOD/m3·d时,系统COD去除率仍有96.47%。污泥浓度对膜生物反应器的COD去除率有较大影响,当MLSS保持在3000～4000mg/L时,膜生物反应器COD去除率为85%左右,高于MLSS保持在7500～7800mg/L时为68%左右。在不排泥运行时膜生物反应器中MLVSS和MLSS比值比排泥运行时低。     

垃圾渗滤液处理工程实例

利用厌氧UASB+膜生物反应器MBR+纳滤工艺处理垃圾填埋场产生的垃圾渗滤液,介绍了各处理阶段的设计、运行参数和经济技术指标,设计处理规模为100 m3/d。在进水ρ(COD)为10 000 mg/L,ρ(BOD5)为5 000 mg/L,经处理后,出水ρ(COD)达到60 mg/L,ρ(BOD5)约为20 mg/L,去除率分别达到99.4%、99.6%,且出水稳定,达到地方标准DB 11/307-2005《北京市水污染排放标准》中二级排放标准。     

厌氧反应器与好氧MBR组合工艺处理毛纺印染废水试验研究

采用厌氧反应器与膜生物反应器(MBR)组合工艺处理毛纺印染废水,结果表明,当进水COD、BOD₅和色度分别为128～321 mg/L、36～95 mg/L和40～70倍时,出水COD、BOD₅、色度、浊度的平均值分别为36.9 mg/L、3.7 mg/L、21倍、0.24 NTU,平均去除率分别达到80.3%%、95%、59%、99.3%,达到生活杂用水水质标准.在本研究中,开发了一种新型的利用生物反应器内液位水头重力驱动连续出水的重力出流式膜生物反应器.在保留MBR处理效率高等优点的同时,省去传统的一体式MBR出水抽吸泵及复杂的反冲洗设备.整个系统结构紧凑,投资少,操作简便.选择合适的曝气量有助于提高膜通量,且可降低膜阻力的上升速率,有利于膜污染的控制.     

UASB-SBR-Fenton法处理中烟废水试验研究

采用UASB-SBR-Fenton法处理中烟废水,最终出水可以达到GB 8978—1996《污水综合排放标准》的二级排放标准,出水色度大大降低。结果表明:UASB反应器稳定运行时,进水COD质量浓度为8 500 mg/L,出水COD质量浓度为1 500 mg/L,去除率为82%;SBR反应器处理UASB的厌氧出水,进水COD质量浓度为1 500 mg/L,出水COD质量浓度为255 mg/L,去除率为83%;取1 LSBR好氧出水,将出水pH值调节至3,投加2.0 g FeSO4催化剂以及10 mL质量分数为30%的双氧水(H2O2),出水COD的质量浓度由255 mg/L变为143 mg/L,去除率为44%。     

一种垃圾渗滤液的处理技术

本文采用厌氧反应器UASB+膜生物反应器MBR+纳滤工艺处理垃圾填埋场废水,设计处理能力为100m3/d,在进水CODs:和BODs分别为10 000 mg/L和5 000 mg/L时,经处理后,出水CODc:和BODs分别为60mg/L和20mg/L,其去除率分别为99.4%和99.6%,且出水稳定,达到了<北京市水...     

生物膜A/O法处理PTA废水的试验研究

在含两级Ａ／Ｏ和生物炭的连续运行试验装置上处理ＰＴＡ废水,结果表明：进水ＣＯＤｃｒ为１１０１ｍｇ／Ｌ,ＨＲＴ为４０ｈ,Ｏ２段和生物炭出水中残余ＣＯＤｃｒ分别为８２ｍｇ／Ｌ和５５ｍｇ／Ｌ,相应ＣＯＤｃｒ去除率分别为９２％和９５％;进水ＣＯＤｃｒ为１１１２ｍｇ／Ｌ,ＨＲＴ为３２ｈ,Ｏ２段和生物炭出水中残余ＣＯＤｃｒ分别为８６ｍｇ／Ｌ和６４ｍｇ／Ｌ,其去除率分别为９２％和９５％;在上述试验条件下刀;段ＴＡ去除率均为９３％。     

QUICKScan as a quick and participatory methodology for problem identification and scoping in policy processes

Policy making is required in cases in which a public good needs to be either maintained or created, and private or civil initiatives cannot deal alone with this. Policy making thus starts with a phase of problem identification and determining whether there is a problem that needs to be dealt with. Rapidly evolving contexts exert influence on policy makers who have to take decisions much faster and more accurately than in the past, also facing greater complexity. There is a need for a method that lowers the lead time of the exploratory phase of the policy cycle. At the same time the method should create a joint understanding of the most important interactions. This paper proposes QUICKScan, a method, process and spatially explicit tool, to jointly scope policy problems in a participatory setting, investigate the most important interactions and feedbacks and assesses the state of knowledge and data of relevance to the problem. QUICKScan uses strongly moderated participatory workshops bringing together a wide range of stakeholders relevant to the policy issue. These moderated workshops jointly build an expert system in a spatially explicit tool using functionality of bayesian belief networks, python programming, simple map algebra and knowledge matrices, with a strong focus on visualization of results. QUICKScan has been applied in 70 different applications in a range of different policy contexts, stakeholders and physical locations. Through these applications participants were able to internalize the knowledge that was usually handed to them in briefs and reports, to develop a joint understanding of the main interactions and their link to impacts and to develop a problem statement and solution space in a reduced lead time. Ultimately, QUICKScan demonstrates another role of science, not solely as a knowledge production, but also facilitating the knowledge consumption.     

A new azhdarchoid pterosaur from the Lower Cretaceous of China and its implications for pterosaur phylogeny and evolution

Toothless pterosaurs played a key role in broadening the taxonomic, morphological and ecological diversity of Cretaceous pterosaurs. Here we report a complete, articulated skeleton of a 1.4-m-wingspan pterosaur from the Lower Cretaceous Jiufotang Formation of Liaoning Province, China which is identified as a new genus and species, Shenzhoupterus chaoyangensis gen. et sp. nov. The new taxon is edentulous, with a relatively large skull and a remarkably large, tall nasoantorbital fenestra that extends well above the main part of the braincase. Phylogenetic analysis shows that Shenzhoupterus gen. nov. belongs in a distinct clade of azhdarchoid pterosaurs, formally recognised here as a new family, Chaoyangopteridae, that also includes Chaoyangopterus, Jidapterus and Eoazhdarcho from the Jiufotang Formation and Eopteranodon from the Yixian Formation. These new data clarify recent confusion surrounding the systematics of these Lower Cretaceous taxa and provide new insights into the evolutionary history of pterosaurs.     

用氟污染桑叶饲养蚕对干茧和丝质量影响的研究

研究表明,桑叶氟污染较重时,干茧和丝的质量受到危害,茧层重、粒茧量和公升茧粒等6项指标均显示干茧质量明显下降;在14项丝质量指标中除清洁度和强伸力外,均有明显氟危害影响.     

云南寻甸中全新世降温事件的石笋同位素记录

通过对寻甸仙人洞X1石笋进行高精度的TIMS-U系测年和碳、氧同位素分析,建立了寻甸地区8000aB.P.以来高分辨率的古气候变化时间序列。研究结果表明,寻甸地区8000aB.P.以来石笋记录的古气候环境变化,大致可分为3个气候期:中全新世8000—5560aB.P.为气候适宜期,显示印度季风由强盛逐渐减弱的趋势,气候温暖湿润期,与太阳辐射增强引起的北半球季风环流加强有关;中全新世中晚期5560—4400aB.P.为季风转变期,显示印度季风减弱并快速退出、萎缩,东亚冬季风加强并快速推进,太阳辐射强度减弱,气候为干冷期;中全新世晚期4400—2000aB.P.,显示东亚冬季风逐渐减弱,东亚夏季风有所增加,气温有所回升,但气候变化的波动大。研究还表明,全新世以来石笋记录的气候变化非常不稳定,在千年尺度上表现为台阶状,在短尺度———百年尺度上呈锯齿状波动。石笋记录的突发性气候波动事件,与冰芯记录极为相似,反映低纬度地区石笋记录的季风气候与高纬度及北极地区的气候具有极好的相关性,这对于认识现代气候系统变化以及对未来十年、百年尺度的气候预测具有重要的科学意义。     

油田化学添加剂对污水处理系统腐蚀行为的影响

目的明确净水剂、絮凝剂、助凝剂、缓蚀剂对污水处理系统腐蚀行为的作用效果。方法通过工艺流程分析、腐蚀形貌观察、腐蚀产物成分分析、腐蚀失重测试等手段,分析污水处理系统腐蚀原因,考察油田化学添加剂对SSF污水处理系统腐蚀行为的影响。结果输送介质中溶解的二氧化碳、高浓度氯离子、氧是导致SSF净化装置内腐蚀的主要原因。分别添加质量浓度为150、0.3、60 mg/L的净水剂、絮凝剂、助凝剂后,动态腐蚀速率可从1.8544 mm/a降到0.6674、0.8627、0.3530 mm/a,静态腐蚀速率可从1.2515 mm/a降到0.9565、0.9474、0.6256 mm/a。添加160 mg/L缓蚀剂,动态腐蚀速率从1.8544 mm/a降低到0.0822 mm/a,静态腐蚀速率从1.2515 mm/a降低到0.0238 mm/a。同时添加净水剂、絮凝剂、助凝剂三种药剂,动态腐蚀速率为0.7672 mm/a,静态腐蚀速率为0.8742 mm/a;同时添加净水剂、絮凝剂、助凝剂、缓蚀剂四种药剂,动态腐蚀速率为0.3069 mm/a,静态腐蚀速率为0.0263 mm/a。结论添加缓蚀剂能有效控制SSF污水处理系统内腐蚀。污水处理用净水剂、絮凝剂、助凝剂对腐蚀有一定抑制作用。在动态条件下,净水剂、絮凝剂、助凝剂降低了缓蚀剂的缓蚀效果,在静态条件下,三种添加剂对缓蚀剂的缓蚀效果影响较小。     

Ecoprofit-Styria-prepare Thirteen pollution prevention case studies in the Styrian industry

The paper focuses upon the organization of a federal state-funded pollution prevention project in the Styrian industry. The project includes 13 companies from the textile, pulp and paper, machine building, wood working and printed circuit board manufacturing industries, covering most of the sectors and sizes in the Styrian industry. It started in January 1994 and will last for one year. It will demonstrate the possibilities of pollution prevention and the need for further research work. This project will make use of the methods and tools that were refined in the Austrian Prepare project. As a first step, a systematic balance of all the inputs and outputs of a company is made, after which the weak points and inefficiencies of material and energy use are identified and the options for improvements, both economical and ecological, are defined. Consequently, modifications in products and production lead to a situation with less waste and emissions. The preliminary lessons from these projects are presented: as a rule, the utilities (consumption of process materials and water, cleaning, energy, preparatory and finishing steps) are treated as black boxes and usually represent a considerable optimization potential. In these areas especially there is usually a lack of information and coordination as well as a need for a systematic and comprehensive approach. Leadership in the company and creative consultants are needed for starting lasting successful pollution prevention projects.     

南京北郊春季气溶胶吸湿性分析

大气气溶胶的吸湿性对气溶胶粒子的谱分布、云凝结核形成、气候强迫、人体健康等均有重要的影响.利用吸湿性串联差分迁移率分析仪(HTDMA)在2014年4月16日~5月21日对南京北郊的大气气溶胶吸湿特性进行观测.30~230 nm气溶胶粒子在90%相对湿度下的吸湿增长观测结果表明,气溶胶粒子的吸湿增长因子平均概率分布函数(GF-PDF)呈现明显的双峰分布,即一个占主导地位的强吸湿模态,和一个相对较小但仍很明显的弱吸湿模态.对吸湿性的日夜对比分析发现,整体上白天的气溶胶粒子吸湿性大于夜间气溶胶粒子,白天强吸湿模态的粒子数目比例高于夜间,夜间气溶胶粒子的外混合程度更高.利用HYSPLIT模式对气溶胶来源分析结果表明,观测期间南京北郊主要受到3类气团的影响.其中西北大陆气团背景下爱根核模态粒子在经过大陆的长距离输送过程后,老化程度较高,吸湿性也更强.而对于积聚模态粒子,则为来自东方气团的粒子吸湿性更强,强吸湿模态粒子数目比例也较高.局地气团背景下气溶胶粒子在各粒径段都具有较高的强吸湿比例.     

灰色理论在预测鱼田堡煤矿矿井涌水量中的应用

煤矿地下水动态的预测预报始终存在着计算过程复杂、计算量大、且难以兼顾影响矿井充水的各种因素、精度较低的特点;灰色系统理论则具有高度的概括性、简单的计算过程和极佳的预测精度,因此在工程界得到了广泛的应用。本文采用灰色系统理论,以灰色理论GM（1,1）模型为基础对重庆鱼田堡煤矿矿井涌水量进行预测。结果表明,该方法在预测矿井涌水量中是一种简便而有效的好方法。根据涌水量预测结果,为矿井设计排水方案的最优化选择提供科学依据。     

Split notochord syndrome variant: prenatal findings and neonatal management

Spilt notochord syndrome is an extremely rare form of spinal dysraphism characterized by a complete cleft of the spine and a persistent communication between endoderm and ectoderm. A variant of split notochord syndrome was diagnosed in a 25-week-old fetus showing a prolapsed congenital colostomy and a spinal cystic lesion. The final diagnosis included protruding colon segment, imperforate anus with a rectourethral fistula and lipomyelomeningocele. The ultrasound features of the condition and the post-natal management are discussed. The neonate was successfully treated with a posterior sagittal anorectoplasty, while the lipomyelomeningocele was resected at a later stage. Copyright © 2005 John Wiley & Sons, Ltd.