ALTERED STREAMFLOW AND SEDIMENT ENTRAINMENT IN THE GUNNISON GORGE1

ABSTRACT: The Gunnison River in the Gunnison Gorge is a canyon river where upstream dams regulate mainstem discharge but do not affect debris-flow sediment supply from tributaries entering below the reservoirs. Regulation since 1966 has altered flood frequency, streambed mobility, and fluvial geomorphology creating potential resource-management issues. The duration of moderate streamflows between 32.3 and 85.0 m³/s has increased threefold since 1966. This, along with flood-peak attenuation, has facilitated fine-sediment deposition and vegetation encroachment on stream banks. The Shields equation and on-site channel geometry and bed-material measurements were used to assess changes in sediment entrainment in four alluvial reaches. Sand and fine gravel are transported through riffle/pool reaches at most discharges, but the cobbles and boulders composing the streambed in many reaches now are infrequently entrained. Periodic debris flows add coarse sediment to rapids and can increase pool elevation and the streambed area affected by backwater and fine-sediment accumulation. Debris-flow supplied boulders accumulate on fans and in rapids and constrict the channel until reworked by larger floods. The response to streamflow-régime changes in the Gunnison Gorge could serve as an analog for alluvial reaches in other regulated canyon rivers.     

Streamflow,Sediment Transport,and Geomorphic Change during the 2011 Flood on the Missouri River Near Bismarck–Mandan,ND

Geomorphic change from extreme events in large managed rivers has implications for river management. A steady‐state, quasi‐three‐dimensional hydrodynamic model was applied to a 29‐km reach of the Missouri River using 2011 flood data. Model results for an extreme flow (500‐year recurrence interval [RI]) and an elevated managed flow (75‐year RI) were used to assess sediment mobility through examination of the spatial distribution of boundary or bed shear stress (τ_b) and longitudinal patterns of average τ_b, velocity, and kurtosis of τ_b. Kurtosis of τ_b was used as an indicator of planform channel complexity and can be applied to other river systems. From differences in longitudinal patterns of sediment mobility for the two flows we can infer: (1) under extreme flow, the channel behaves as a single‐thread channel controlled primarily by flow, which enhances the meander pattern; (2) under elevated managed flows, the channel behaves as multithread channel controlled by the interaction of flow with bed and channel topography, resulting in a more complex channel; and (3) for both flows, the model reach lacks a consistent pattern of deposition or erosion, which indicates migration of areas of erosion and deposition within the reach. Despite caveats and limitations, the analysis provides useful information about geomorphic change under extreme flow and potential implications for river management. Although a 500‐year RI is rare, extreme hydrologic events such as this are predicted to increase in frequency.     

GEOMORPHOLOGY OF STEEPLAND HEADWATERS: THE TRANSITION FROM HILLSLOPES TO CHANNELS1

Headwater streams comprise 60 to 80 percent of the cumulative length of river networks. In hilly to mountainous terrain, they reflect a mix of hillslope and channel processes because of their close proximity to sediment source areas. Their morphology is an assemblage of residual soils, landslide deposits, wood, boulders, thin patches of poorly sorted alluvium, and stretches of bedrock. Longitudinal profiles of these channels are strongly influenced by steps created by sediment deposits, large wood, and boulders. Due to the combination of small drainage area, stepped shallow gradient, large roughness elements, and cohesive sediments, headwater streams typically transport little sediment or coarse wood debris by fluvial processes. Consequently, headwaters act as sediment reservoirs for periods spanning decades to centuries. The accumulated sediment and wood may be episodically evacuated by debris flows, debris floods, or gully erosion and transported to larger channels. In mountain environments, these processes deliver significant amounts of materials that form riverine habitats in larger channels. In managed steepland forests, accelerated rates of landslides and debris flows resulting from the harvest of headwater forests have the potential to seriously impact the morphology of headwater streams and downstream resources.     

AN ANALYTICAL FRAMEWORK FOR EVALUATING CHANNEL MAINTENANCE FLOWS IN COLORADO1

ABSTRACT: An accounting procedure is developed which determines a flow regime that is capable of transporting an amount of bedload sediment necessary to ensure channel stability downstream. The method allows for sediment buildup in the channel within geomorphic threshold limits during low flow periods. During periods of high runoff, enough water is bypassed to transport the stored sediment. The procedure utilizes only those flows of sufficient magnitude to maintain channel stability over the long run (25–50+ years). An example is presented which determines the volume of water and frequency of release for channel maintenance purposes downstream from a hypothetical water diversion project. Of some 1,200,000 acre feet generated during a 59-year period, 86,500 acre feet was required for channel maintenance flows. Bypass flows were not required each year, but only during those years when average daily flow reached bankfull or greater. Such releases were made on 202 of the 411 days when average flows either equalled or exceeded bankfull discharge.     

Channel and Perennial Flow Initiation in Headwater Streams: Management Implications of Variability in Source-Area Size

Despite increasing attention to management of headwater streams as sources of water, sediment, and wood to downstream rivers, the extent of headwater channels and perennial flow remain poorly known and inaccurately depicted on topographic maps and in digital hydrographic data. This study reports field mapping of channel head and perennial flow initiation locations in forested landscapes underlain by sandstone and basalt lithologies in Washington State, USA. Contributing source areas were delineated for each feature using a digital elevation model (DEM) as well as a Global Positioning System device in the field. Systematic source area–slope relationships described in other landscapes were not evident for channel heads in either lithology. In addition, substantial variability in DEM-derived source area sizes relative to field-delineated source areas indicates that in this area, identification of an area–slope relationship, should one even exist, would be difficult. However, channel heads and stream heads, here defined as the start of perennial flow, appear to be co-located within both of the lithologies, which together with lateral expansion and contraction of surface water around channel heads on a seasonal cycle in the basalt lithology, suggest a controlling influence of bedrock springs for that location. While management strategies for determining locations of channel heads and perennial flow initiation in comparable areas could assign standard source area sizes based on limited field data collection within that landscape, field-mapped source areas that support perennial flow are much smaller than recognized by current Washington State regulations.     

Enhancing Hyrdological Simulation Program – FORTRAN Model Channel Hydraulic Representation1

Abstract: The hydrological simulation program – FORTRAN (HSPF) is a comprehensive watershed model that employs depth‐area‐volume‐flow relationships known as the hydraulic function table (FTABLE) to represent the hydraulic characteristics of stream channel cross‐sections and reservoirs. An accurate FTABLE determination for a stream cross‐section site requires an accurate determination of mean flow depth, mean flow width, roughness coefficient, longitudinal bed slope, and length of stream reach. A method that uses regional regression equations to estimate mean flow depth, mean flow width, and roughness coefficient is presented herein. FTABLES generated by the proposed method (Alternative Method) and FTABLES generated by Better Assessment Science Integrating Point and Nonpoint Sources (BASINS) were compared. As a result, the Alternative Method was judged to be an enhancement over the BASINS method. First, the Alternative Method employs a spatially variable roughness coefficient, whereas BASINS employs an arbitrarily selected spatially uniform roughness coefficient. Second, the Alternative Method uses mean flow width and mean flow depth estimated from regional regression equations whereas BASINS uses mean flow width and depth extracted from the National Hydrography Dataset (NHD). Third, the Alternative Method offers an option to use separate roughness coefficients for the in‐channel and floodplain sections of compound channels. Fourth, the Alternative Method has higher resolution in the sense that area, volume, and flow data are calculated at smaller depth intervals than the BASINS method. To test whether the Alternative Method enhances channel hydraulic representation over the BASINS method, comparisons of observed and simulated streamflow, flow velocity, and suspended sediment were made for four test watersheds. These comparisons revealed that the method used to estimate the FTABLE has little influence on hydrologic calibration, but greatly influences hydraulic and suspended sediment calibration. The hydrologic calibration results showed that observed versus simulated daily streamflow comparisons had Nash‐Sutcliffe efficiencies ranging from 0.50 to 0.61 and monthly comparisons had efficiencies ranging from 0.61 to 0.84. Comparisons of observed and simulated suspended sediments concentrations had model efficiencies ranging from 0.48 to 0.56 for the daily, and 0.28 to 0.70 for the monthly comparisons. The overall results of the hydrological, hydraulic, and suspended sediment concentration comparisons show that the Alternative Method yielded a relatively more accurate FTABLE than the BASINS method. This study concludes that hydraulic calibration enhances suspended sediment simulation performance, but even greater improvement in suspended sediment calibration can be achieved when hydrological simulation performance is improved. Any improvements in hydrological simulation performance are subject to improvements in the temporal and spatial representation of the precipitation data.     

A Decade of Geomorphic and Hydraulic Response to the La Valle Dam Project,Baraboo River,Wisconsin

We investigate stream response to the La Valle Dam removal and channel reconstruction by estimating channel hydraulic parameter values and changes in sedimentation within the reservoir. The designed channel reconstruction after the dam removal included placement of a riffle structure at the former dam site. Stream surveys undertaken in 1984 by Federal Emergency Management Agency and in 2001 by Doyle et al. were supplemented with surveys in 2009 and 2011 to study the effects of the instream structure. We created a model in HEC‐RAS IV and surface maps in Surfer© using the 1984, 2009, and 2011 surveys. The HEC‐RAS IV model for 2009 channel conditions indicates that the riffle structure decreases upstream channel shear stress and velocity, causing renewed deposition of sediment within the former reservoir. We estimate by 2009, 61% of former reservoir sediments were removed during dam removal and channel reconstruction. Between 2009 and 2011 renewed sedimentation within the former reservoir represented approximately 7.85% of the original reservoir volume. The HEC‐RAS IV models show the largest impacts of the dam and riffle structure occur at flood magnitudes at or below bankfull. Thus, the riffle and the dam similarly alter channel hydraulics and sediment transport. As such, our models indicate that the La Valle Dam project was a dam replacement rather than a removal. Our results confirm that channel reconstruction method can alter channel hydraulics, geomorphology, and sediment mobility.     

A Geomorphic Explanation for a Meander Cutoff Following Channel Relocation of a Coarse-Bedded River

The Veteran's Fishing section of the Blackledge River in central Connecticut was relocated in the late 1950s. The relocation resulted in an unstable channel despite extensive efforts to prevent erosion. Overbank erosion and meander cutoffs were investigated using detailed survey data, characterizations of sediment deposits, flow modeling, and a moment-stability analysis. Limited reworking of revetment boulders indicate that riprap bank material was immobile during a 1979 flood event responsible for the formation of the cutoff channel. A moment-stability analysis factor-of-safety value of 1.1 supports the conclusion that riprap was not directly eroded from the banks. Alluvial particles with d₉₅ values ranging up to 120 mm were deposited along a bar downstream from the cutoff channel at flows estimated to be below a 1.5-year recurrence interval flow. Development of the bar deposit resulted in locally elevated water surfaces at high flow. The resulting overbank flow across the meander neck to the adjacent downstream bend led to the creation of an upstream migrating knickpoint, the erosion of approximately 16,000-year-old sediments, and the subsequent meander cutoff. The results of the study indicate that traditional erosion-control measures cannot prevent extreme channel adjustments if the geomorphic processes that control sediment continuity also are not considered.     

Establishing a Context for River Rehabilitation, North Fork Gunnison River, Colorado

Initial river rehabilitation efforts along the North Fork Gunnison River in Colorado focused on the use of in-stream structures and channel stabilization to create a single-thread channel with pools along a braided river. These efforts were based on the assumption that the river’s braided planform results primarily from land use during the past century. In order to establish a context for further rehabilitation, we evaluated the possibility that the river might be braided as a result of processes independent of land use. We estimated volume, grain-size distribution, and lithology of sediment sources along the river corridor and evaluated the planform stability of the river during the past century using historical sources, aerial photographs covering 1939–1997, and comparison of bankfull discharge and gradient in the study area to values published for braided and meandering rivers. Our results indicate that the North Fork Gunnison River has been primarily braided in its lower reaches during the past few hundred years, although the channel planform tends toward a single-thread channel during decades of lower precipitation and discharge. Although land use is not the primary cause of braiding along the North Fork Gunnison River, it has decreased channel stability, and rehabilitation efforts should be designed to reduce these effects. Our results illustrate the importance of planning river rehabilitation measures within a historical context that accounts for both catchment-scale and reach-scale controls on channel processes and planform.     

Impact of Temporal Resolution of Flow‐Duration Curve on Sediment Load Estimation1

Chen, Li, Rina Schumer, Anna Knust, and William Forsee, 2011. Impact of Temporal Resolution of Flow‐Duration Curve on Sediment Load Estimation. Journal of the American Water Resources Association (JAWRA) 48(1): 145‐155. DOI: 10.1111/j.1752‐1688.2011.00602.x Abstract: Estimates of a channel’s annual sediment transport capacity typically incorporate annualized flow‐duration curves. Average daily flow data, commonly used to develop flow‐duration curves, may not adequately describe sediment‐transporting flows in arid and semiarid ephemeral streams. In this study, we examined impacts of varied temporal resolution flow data on annual sediment load estimation. We derived flow‐duration curves for eight sites in the Southwestern United States based on both 15‐min and daily‐averaged flow data. We then estimated sediment loads for both flow‐duration curves using the Sediment Impact Analysis Method, implemented in HEC‐RAS. When average daily flow is used to generate flow‐duration curves, sediment load estimation is lower by up to an order of magnitude. This trend is generally unaffected by uncertainty associated with sediment particle size or hydraulic roughness. The ratio of sediment loads estimated by 15‐min versus daily‐averaged flow‐duration curves is strongly correlated with channel slope, being greater on steep‐slope channels. Sediment loads estimated by the two types of flow‐duration curves are closely correlated, suggesting possible relationships for improving predictions when high‐temporal resolution data are unavailable. Results also suggest that the largest flow contributes significantly to total sediment load, and thus will greatly impact ephemeral stream geomorphology in arid and semiarid regions.     

DEBRIS FLOWS THROUGH DIFFERENT FOREST AGE CLASSES IN THE CENTRAL OREGON COAST RANGE1

ABSTRACT: Debris flows in the Pacific Northwest can play a major role in routing sediment and wood stored on hillslopes and in first‐through third‐order channels and delivering it to higher‐order channels. Field surveys following a large regional storm event investigated 53 debris flows in the central Oregon Coast Range to determine relationships among debris flow characteristics and the age class of the surrounding forest. The volume of sediment and wood delivered by debris flows was strongly correlated with runout length. Debris flows that initiated at roads were significantly longer than nonroad related failures, and road related landslides were an order of magnitude larger than nonroad related landslides. Clearcuts and roads tended to have more numerous contributing landslides relative to second growth and mature forests. No statistically significant difference in the average debris flow runout length was detected among the forest age classes, although debris flows initiating in clearcuts and mixed forest and at roads occasionally supported extremely long runout lengths that were outside the range of variability observed in completely forested basins. The size of wood in deposits was not correlated with the size of trees on the adjacent slopes, suggesting that the majority of wood in debris flow deposits was from remobilization of wood previously stored in low order channels.     

ASSESSING STREAM CHANNEL STABILITY THRESHOLDS USING FLOW COMPETENCE ESTIMATES AT BANKFULL STAGE1

ABSTRACT: Stream channel stability is affected by peak flows rather than average annual water yield. Timber harvesting and other land management activities that contribute to soil compaction, vegetation removal, or increased drainage density can increase peak discharges and decrease the recurrence interval of bankfull discharges. Increased peak discharges can cause more frequent movement of large streambed materials, leading to more rapid stream channel change or instability. This study proposes a relationship between increased discharge and channel stability, and presents a methodology that can be used to evaluate stream channel stability thresholds on a stream reach basis. Detailed surveys of the channel cross section, water surface slope, streambed particle size distribution, and field identification of bankfull stage are used to estimate existing bankfull flow conditions. These site specific stream channel characteristics are used in bed load movement formulae to predict critical flow conditions for entrainment of coarse bed material (D₈₄ size fraction). The “relative bed stability” index, defined as the ratio of critical flow condition to the existing condition at bankfull discharge, can predict whether increased peak discharges will exceed stream channel thresholds.     

Mobilization and Toxicity Potential of Aluminum from Alum Floc Deposits in Kensico Reservoir,New York

There is detailed literature on the mobilization of aluminum (Al) from soil to surface waters as a result of elevated acidic deposition to base‐poor forest watersheds. There is considerably less information on the mobilization and effects of Al from the application of alum that is used in some water supplies to control turbidity during high‐flow events. We report on the results of field measurements, laboratory sediment release experiments, and chemical equilibrium calculations conducted to evaluate the potential for the mobilization of Al from alum floc deposits in sediments of Kensico Reservoir, New York. Under ambient water quality conditions, mobilization of sediment Al is not a noteworthy concern at Kensico Reservoir. However, under experimental conditions of low pH, low acid neutralizing capacity (ANC), and low temperature, the inorganic fraction of monomeric Al can be mobilized from Kensico sediments to concentrations that would likely impair the health of aquatic organisms (>2 μmol/l). Elevated concentrations of monomeric Al were observed only when ANC decreased below 50 μeq/l, which is outside the range of values observed in Kensico during the 1997‐2007 interval (120‐460 μeq/l). Concentrations of complexing ligands are relatively low in Kensico waters (i.e., fluoride, naturally occurring organic solutes) and do not appear to substantially contribute to potential Al mobilization. For other water supplies with low ANC, the potential for sediment release of Al may exist.     

EVALUATION OF STORMSEWER CONTROL ALGORITHMS USING A TRANSIENT MIXED FLOW MODEL1

ABSTRACT: a hydraulic transient model that is capable of simultaneously modeling open channel and pressurized flows is used to study active control of a deep tunnel stormwater collection system. The simultaneous occurrence of open channel flow and pressurized flow is termed mixed flow. This paper demonstrates the application of a mixed flow hydraulic model to the development of an active control scheme. It is shown that dynamic conditions can exist in a storm sewer system even under moderate inflow conditions and that these conditions, particularly at the time of full system pressurization, can influence the operation of the dynamic control, so that accurate hydraulic modeling is essential to proper control formulation.     

SEDIMENT DISPERSION IN SALMON SPAWNING STREAMS: THE INFLUENCE OF FLOODS AND SALMON REDD CONSTRUCTION1

ABSTRACT: Magnetically tagged particles were used to investigate the effects of sockeye salmon (Oncorhynchus nerka) and floods on the dispersion of coarse bed material in the Stuart‐Takla region, British Columbia, Canada. The dominant annual sediment transporting event in the channels is the snowmelt flood events, with lesser activity usually accomplished during summer floods. Annually in August, the channel bed material is reworked by the Early Stuart sockeye salmon spawning, as the fish excavate the streambed to deposit and bury their eggs. These nesting cavities are called redds. Results from 67 tracer recovery experiments over five years were highly variable, subject to the magnitude of floods and the returning population of salmon. Overall, the depositional pattern from nival flood events usually demonstrated a high degree of clast mobilization, long travel distances (up to 150 m), and mean depths of burial up to 18 cm. Summer flood events showed somewhat lower rates of mobilization, distances of travel, and depths of burial. Although the fish did not move the tracers very far, their effect on the bed was generally quite pervasive ‐ up to 100 percent of the clasts were mobilized, and the depth of burial was considerable (mean burial depths up to 14 cm). The amount of vertical mixing of sediment by salmon was often on the same order of magnitude as flood events. The significant vertical mixing of sediments by the fish has important implications for the mobility of sediment in the stream. Since any armoring layer formed during high flows throughout the year is subject to the bioturbation of salmon, this suggests that the transport threshold in the creeks remains relatively low. Salmon likely play an integral role in the sediment transport dynamics and annual sediment budget of the lower reaches of these creeks.     

THE DEPENDENCE OF THE RESIDUAL GRAVITY ON HYDRAULIC CONSTANTS IN GLACIAL DEPOSITS1

ABSTRACT: Buried glacial stream channels contain large and easily accessible groundwater resources. Gravity surveys have been frequently applied for their location. A gravity survey in the geohydrologically explored Wood River Valley Area of southern Rhode Island shows extreme lows of -2 mgals over channel depths of maximal 300 feet. Three gravity profiles were observed in east-west direction across a north-south striking stream channel. The bedrock depth increases rapidly towards the south from 130 to 300 feet. The gravity lows observed across each profile are not related to the bedrock depth but rather to the saturated thickness of the main quifer and its hydraulic transmissivity. Well logs indicate that the large change of bedrock depth is solely due to an increase of till of low permeability. The volume of the glacial outwash, which is the major groundwater resource, changes little underneath the three profiles. The gravity lows apear to be directly related to the density contrast between glacial outwash and till. The response to the hydraulically more pertinent units renews the interest in the gravity method as it may have a potential to estimate yields of hydrologically complex aquifers     

ASSESSING FLUSHING-FLOW REQUIREMENTS FOR BROWN TROUT SPAWNING GRAVELS IN STEEP STREAMS1

Flushing flows are re1eses from dams designed to remove fine sediment from downstream spawning habitat. We evaluated flushing flows on reaches proposed for hydroelectric diversions on seven streams in the eastern Sierra Nevada, California, with wild populations of brown trout (Salmo trutta). The stream reaches are steep (average map slopes range from 7 to 17 percent), are dominated by boulder cascades, and afford few opportunities for gravel deposition. Methods for estimating flushing flows from flow records, developed from studies in other localities, produced widely differing results when applied to the study streams, probably reflecting differences in the hydrologic and geomorphic characteristics of the streams on which the methods were developed. Tracer gravel experiments demonstrated that all sampled gravels were washed out by the flows of 1986, a wet year. Size analyses of gravel samples and hydraulic data from field surveys were used in tractive-force calculations in an attempt to specify the flow required to flush the gravels. However, these calculations produced some unrealistic results because the flows were nonuniform in the study reaches. This suggests that the tractive-force approach may not be generally applicable to small, steep streams where nonuniform flow conditions prevail.     

Constructing an Interdisciplinary Flow Regime Recommendation1

Bartholow, John M., 2010. Constructing an Interdisciplinary Flow Regime Recommendation. Journal of the American Water Resources Association (JAWRA) 1-15. DOI: 10.1111/j.1752-1688.2010.00461.x Abstract: It is generally agreed that river rehabilitation most often relies on restoring a more natural flow regime, but credibly defining the desired regime can be problematic. I combined four distinct methods to develop and refine month-by-month and event-based flow recommendations to protect and partially restore the ecological integrity of the Cache la Poudre River through Fort Collins, Colorado. A statistical hydrologic approach was used to summarize the river’s natural flow regime and set provisional monthly flow targets at levels that were historically exceeded 75% of the time. These preliminary monthly targets were supplemented using results from three Poudre-specific disciplinary studies. A substrate maintenance flow model was used to better define the high flows needed to flush accumulated sediment from the river’s channel and help sustain the riparian zone in this snowmelt-dominated river. A hydraulic/habitat model and a water temperature model were both used to better define the minimum flows necessary to maintain a thriving cool water fishery. The result is a range of recommended monthly flows and daily flow guidance illustrating the advantage of combining a wide range of available disciplinary information, supplemented by judgment based on ecological principles and a general understanding of river ecosystems, in a highly altered, working river.