Estimation of uranium and radon concentration in some drinking water samples of Upper Siwaliks, India

Uranium and radon concentration was assessed in water samples taken from hand pumps, natural sources and wells collected from some areas of Upper Siwaliks, Northern India. Fission track registration technique was used to estimate the uranium content of water samples. The uranium concentration in water samples was found to vary from 1.08 +/- 0.03 to 19.68 +/- 0.12 microg l(-1). These values were compared with safe limit values recommended for drinking water. Most of the water samples were found to have uranium concentration below the safe limit of 15 microg l(-1) (WHO, World Health Organization, Guidelines for drinking-water quality (3rd ed.). Geneva, Switzerland: WHO, 2004). The radon estimation in these water samples was made using alpha-scintillometry to study its correlation with uranium. The radon concentration in these samples was found to vary from 0.87 +/- 0.29 to 32.10 +/- 1.79 Bq l(-1). The recorded values of radon concentration were within the recommended safe limit of 4 to 40 Bq l(-1) (UNSCEAR, United Nations Scientific Committee on the Effects of Atomic Radiations, Sources and effects of ionizing radiation. New York: United Nations, 1993). No direct correlation was found between uranium concentration and radon concentration in water samples belonging to Upper Siwaliks. The values of uranium and radon concentration in water were compared with that from the adjoining areas of Punjab state, India.     

Assessment of ground water quality for drinking purpose, District Nainital, Uttarakhand, India

The ground water quality of District Nainital (Uttarakhand, India) has been assessed to see the suitability of ground water for drinking and irrigation applications. This is a two-part series paper and this paper examines the suitability of ground water including spring water for drinking purposes. Forty ground water samples (including 28 spring samples) were collected during pre- and post-monsoon seasons and analyzed for various water quality constituents. The hydrochemical and bacteriological data was analyzed with reference to BIS and WHO standards and their hydrochemical facies were determined. The concentration of total dissolved solids exceeds the desirable limit of 500 mg/L in about 10% of the samples, alkalinity values exceed the desirable limit of 200 mg/L in about 30% of the samples, and total hardness values exceed the desirable limit of 300 mg/L in 15% of the samples. However, no sample crosses the maximum permissible limit for TDS, alkalinity, hardness, calcium, magnesium, chloride, sulfate, nitrate, and fluoride. The concentration of chloride, sulfate, nitrate, and fluoride are well within the desirable limit at all the locations. The bacteriological analysis of the samples does not show any sign of bacterial contamination in hand pump and tube-well water samples. However, in the case of spring water samples, six samples exceed the permissible limit of ten coliforms per 100 ml of sample. It is recommended that water drawn from such sources should be properly disinfected before being used for drinking and other domestic applications. Among the metal ions, the concentration of iron and lead exceeds the permissible limit at one location whereas the concentration of nickel exceeds the permissible limit in 60 and 32.5% of the samples during pre- and post-monsoon seasons, respectively. The grouping of samples according to their hydrochemical facies indicates that majority of the samples fall in Ca–Mg–HCO₃ hydrochemical facies.     

Heavy metal contaminations in the groundwater of Brahmaputra flood plain: an assessment of water quality in Barpeta District, Assam (India)

A study was conducted to evaluate the heavy metal contamination status of groundwater in Brahmaputra flood plain Barpeta District, Assam, India. The Brahmaputra River flows from the southern part of the district and its many tributaries flow from north to south. Cd, Fe, Mn, Pb, and Zn are estimated by using atomic absorption spectrometer, Perkin Elmer AA 200. The quantity of heavy metals in drinking water should be checked time to time; as heavy metal accumulation will cause numerous problems to living being. Forty groundwater samples were collected mainly from tube wells from the flood plain area. As there is very little information available about the heavy metal contamination status in the heavily populated study area, the present work will help to be acquainted with the suitability of groundwater for drinking applications as well as it will enhance the database. The concentration of iron exceeds the WHO recommended levels of 0.3 mg/L in about 80% of the samples, manganese values exceed 0.4 mg/L in about 22.5% of the samples, and lead values also exceed limit in 22.5% of the samples. Cd is reported in only four sampling locations and three of them exceed the WHO permissible limit (0.003 mg/L). Zinc concentrations were found to be within the prescribed WHO limits. Therefore, pressing awareness is needed for the betterment of water quality; for the sake of safe drinking water. Statistical analysis of the data was carried out using Special Package for Social Sciences (SPSS 16).     

Determination of 226Ra at ultratrace level in mineral water samples by sector field inductively coupled plasma mass spectrometry

An analytical procedure has been proposed for the determination of (226)Ra at the low femtogram per ml concentration level in mineral water samples using double focusing sector field ICP-MS (ICP-SFMS). For the pre-concentration and separation of radium from the matrix elements in water a tandem of a laboratory-prepared filter, based on MnO(2), and Eichrom "Sr-specific" resin was used. The recovery of the method was determined to be 70.5%. The limit of detection for (226)Ra determination was 0.02 fg ml(-1), including a pre-concentration factor of 10. In addition, uranium concentration and uranium isotope ratios were measured by ICP-SFMS. In several mineral water samples with a relatively high uranium content, (226)Ra concentrations were found between 0.7-15 fg ml(-1). The effective dose of the contribution was calculated using the radionuclide concentration and dose conversion factors from the World Health Organization, WHO (1993). Assuming a mineral water consumption of 2 l d(-1), a slightly higher calculated dose than the suggested limit for drinking water (0.1 mSv y(-1)) was found in some samples.     

Analysis of uranium and its correlation with some physico-chemical properties of drinking water samples from Amritsar, Punjab

Fission track technique has been used for uranium estimation in drinking water samples collected from some areas of Amritsar District, Punjab, India. The uranium concentration in water samples is found to vary from 3.19 to 45.59 microg l(-1). Some of the physico-chemical properties such as pH, conductance and hardness and the content of calcium, magnesium, total dissolved solids (TDS), sodium, potassium, chloride, nitrate and heavy metals viz. zinc, cadmium, lead and copper have been determined in water samples. An attempt has been made to correlate uranium concentration with these water quality parameters. A positive correlation of conductance, nitrate, chloride, sodium, potassium, magnesium, TDS, calcium and hardness with uranium concentration has been observed. However, no correlation has been observed between the concentration of uranium and the heavy metals analysed.     

Arsenic content in ground and canal waters of Punjab, North-West India

Groundwater is the primary source of drinking water for more than 95% of the population in Punjab. The world health organization and US Environment Protection Agency recently established a new maximum contaminant level of 10 ppb for arsenic in drinking water. The arsenic concentration of deep water tube wells located in Amritsar city used for domestic supply for urban population ranged from 3.8 to 19.1 ppb with mean value of 9.8 ppb. Arsenic content in hand pump water varied from 9 to 85 ppb with a mean value of 29.5 ppb. According to the safe limit of As, 54% and 97%, water samples collected from deep water tube wells and hand pumps, respectively, were not fit for human consumption. Arsenic content in canal water varied from 0.3 to 8.8 ppb with a mean value of 2.89 ppb. Canal water has got higher oxidation potential followed by deep tube well and hand pump water. The present study suggests the regular monitoring of arsenic content in deep tube well and shallow hand pump waters by water testing laboratories. The consumption of water having elevated concentration of As above the safe limit must be discouraged. In south-western districts of Punjab, it recommends the use of canal water for drinking purposes and domestic use by rural and urban populations than ground water sources.     

Analysis of elemental concentration using ICP-AES and pathogen indicator in drinking water of Qasim Abad, District Rawalpindi, Pakistan

The present study was conducted to investigate drinking water quality (groundwater) from water samples taken from Qasim Abad, a locality of approximately 5,000 population, situated between twin cities Rawalpindi and Islamabad in Pakistan. The main sources of drinking water in this area are water bores which are dug upto the depth of 250–280 ft in almost every house. The study consists of the determination of physico-chemical properties, trace metals, heavy metals, rare earth elements and microbiological quality of drinking water. The data showed the variation of the investigated parameters in samples as follows: pH 6.75 to 8.70, electrical conductivity 540 to 855 μS/cm, total dissolved solids 325.46 to 515.23 ppm and dissolved oxygen 1.50 to 5.64 mg/L which are within the WHO guidelines for drinking water quality. The water samples were analysed for 30 elements (aluminium, iron, magnesium, manganese, silicon, zinc, molybdenum, titanium, chromium, nickel, tungsten, silver, arsenic, boron, barium, beryllium, cadmium, cobalt, copper, gallium, mercury, lanthanum, niobium, neodymium, lead, selenium, samarium, tin, vanadium and zirconium) by using inductively coupled plasma atomic emission spectroscopy. The organic contamination was detected in terms of most probable number (MPN) of faecal coliforms. Overall, elemental levels were lower than the recommended values but three water bores (B-1, B-6, B-7) had higher values of iron (1.6, 2.206, 0.65 ppm), two water bores (B-1, B-6) had higher values of aluminium (0.95, 1.92 ppm), respectively, and molybdenum was higher by 0.01 ppm only in one water bore (B-11). The total number of coliforms present in water samples was found to be within the prescribed limit of the WHO except for 5 out of 11 bore water samples (B-2, B-3, B-4, B-8, B-11), which were found in the range 5–35 MPN/100 mL, a consequence of infiltration of contaminated water (sewage) through cross connection, leakage points and back siphoning.     

Evaluation of surface water quality in aquatic bodies under the influence of uranium mining (MG, Brazil)

The quality of the water in a uranium-ore-mining area located in Caldas (Minas Gerais State, Brazil) and in a reservoir (Antas reservoir) that receives the neutralized acid solution leaching from the waste heaps generated by uranium mining was investigated. The samples were collected during four periods (October 2008, January, April and July 2009) from six sampling stations. Physical and chemical analyses were performed on the water samples, and the data obtained were compared with those of the Brazilian Environmental Standards and WHO standard. The water samples obtained from waste rock piles showed high uranium concentrations (5.62 mg L^?1), high manganese values (75 mg L^?1) and low average pH values (3.4). The evaluation of the water quality at the point considered the limit between the Ore Treatment Unit of the Brazilian Nuclear Industries and the environment (Consulta Creek) indicated contamination by fluoride, manganese, uranium and zinc. The Antas reservoir showed seasonal variations in water quality, with mean concentrations for fluoride (0.50 mg L^?1), sulfate (16 mg L^?1) and hardness (20 mg L^?1) which were low in January, evidencing the effect of rainwater flowing into the system. The concentrations for fluoride, sulfate and manganese were close or above to the limits established by current legislation at the point where the treated mining effluent was discharged and downstream from this point. This study demonstrated that the effluent discharged by the UTM affected the quality of the water in the Antas reservoir, and thus the treatments currently used for effluent need to be reviewed.     

Assessment of groundwater quality in a region of endemic fluorosis in the northeast of Brazil

The aim of this study was to estimate the risk for caries and fluorosis in a desertification area, applying the calcium/fluoride concentration ratio of underground water and the quality of water in a selected geographical region. This study was performed in the municipality of São João do Rio do Peixe, located in the tropical semiarid lands of Brazil. A total of 111 groundwater samples were collected. Fluoride concentration varied from 0.11 to 9.33 mg/L. Thirty percent of all samples analyzed showed values above 1.5 mg/L, while 64 % were above the ideal limit of 0.7 mg/L. Mean calcium concentration was 47.6 mg/L, and 14.4 % of all samples presented values above the WHO acceptable limits. The proportional value of calcium/fluoride in water showed that only 12 % of the samples were suitable for dental caries prevention with minimal risk for dental fluorosis. Mapping of the fluoride distribution indicated that approximately 2,465 people could be affected by dental fluorosis and 1,057 people might be affected by skeletal fluorosis. It can be concluded that, in addition to fluoride, many water parameters were not suitable for the drinking water. Mapping out calcium/fluoride ratio may indicate areas of water suitability for caries control, whereas the fluoride concentration solely can indicate the areas with the risk for fluorosis. This approach can be relevant for health authorities for identifying communities where dental caries or dental fluorosis is prevalent.     

Using a relative health indicator (RHI) metric to estimate health risk reductions in drinking water

When a new drinking water regulation is being developed, the USEPA conducts a health risk reduction and cost analysis to, in part, estimate quantifiable and non-quantifiable cost and benefits of the various regulatory alternatives. Numerous methodologies are available for cumulative risk assessment ranging from primarily qualitative to primarily quantitative. This research developed a summary metric of relative cumulative health impacts resulting from drinking water, the relative health indicator (RHI). An intermediate level of quantification and modeling was chosen, one which retains the concept of an aggregated metric of public health impact and hence allows for comparisons to be made across “cups of water,” but avoids the need for development and use of complex models that are beyond the existing state of the science. Using the USEPA Six-Year Review data and available national occurrence surveys of drinking water contaminants, the metric is used to test risk reduction as it pertains to the implementation of the arsenic and uranium maximum contaminant levels and quantify “meaningful” risk reduction. Uranium represented the threshold risk reduction against which national non-compliance risk reduction was compared for arsenic, nitrate, and radium. Arsenic non-compliance is most significant and efforts focused on bringing those non-compliant utilities into compliance with the 10 μg/L maximum contaminant level would meet the threshold for meaningful risk reduction.     

Groundwater arsenic contamination in Brahmaputra river basin: a water quality assessment in Golaghat (Assam), India

Distribution of arsenic (As) and its compound and related toxicology are serious concerns nowadays. Millions of individuals worldwide are suffering from arsenic toxic effect due to drinking of As-contaminated groundwater. The Bengal delta plain, which is formed by the Ganga?CPadma?CMeghna?CBrahmaputra river basin, covering several districts of West Bengal, India, and Bangladesh is considered as the worst As-affected alluvial basin. The present study was carried out to examine As contamination in the state of Assam, an adjoining region of the West Bengal and Bangladesh borders. Two hundred twenty-two groundwater samples were collected from shallow and deep tubewells of six blocks of Golaghat district (Assam). Along with total As, examination of concentration levels of other key parameters, viz., Fe, Mn, Ca, Na, K, and Mg with pH, total hardness, and SO $_{4}^{2-}$ , was also carried out. In respect to the permissible limit formulated by the World Health Organization (WHO; As 0.01 ppm, Fe 1.0 ppm, and Mn 0.3 ppm for potable water), the present study showed that out of the 222 groundwater samples, 67%, 76.4%, and 28.5% were found contaminated with higher metal contents (for total As, Fe, and Mn, respectively). The most badly affected area was the Gamariguri block, where 100% of the samples had As and Fe concentrations above the WHO drinking water guideline values. In this block, the highest As and Fe concentrations were recorded 0.128 and 5.9 ppm, respectively. Tubewell water of depth 180 ± 10 ft found to be more contaminated by As and Fe with 78% and 83% of the samples were tainted with higher concentration of such toxic metals, respectively. A strong significant correlation was observed between As and Fe (0.697 at p < 0.01), suggesting a possible reductive dissolution of As?CFe-bearing minerals for the mobilization of As in the groundwater of the region.     

Freshwater environmental quality parameters of man-made lakes of Serbia

In this study, 28 lakes were selected from the freshwater resources of the network of man-made lakes throughout the Vojvodina Province and the central part of Serbia. Samples were analyzed for the physicochemicals indicators of the water and nutrients. Most of the values of the chemicals indicators and nutrients of the samples from the Vojvodina Province exceeded the Water Act and Regulations on the Monitoring of Water Quality introduced by the Government of the Republic of Serbia (MWQ) and/or the World Health Organization (WHO) drinking water standards. These samples may not be suitable for human consumption. The sample from Lake Me?uvr?je, where the NH₄ ⁺ concentration was 0.28 mg/L, and the sample from Ovcar Banja, where the total phosphorus (TP) content was 0.15 mg/L with a high total nitrogen (TN) content of 1.21 mg/L, are particularly noteworthy. These high concentrations exceeded the proposed guidelines for safe drinking water; therefore, water from these lakes should be used with care as harmful health effects may occur. The majority of the Serbian lakes are characterized by phosphorus-limited photosynthesis.     

Fluoride contamination in drinking water in rural habitations of Central Rajasthan, India

Fluoride concentration in groundwater sources used as major drinking water source in rural area of block Nawa (Nagaur District), Rajasthan was examined and the toxic effects by intake of excess fluoride on rural habitants were studied. In block 13, habitations (30%) were found to have fluoride concentration more than 1.5 mg/l (viz. maximum desirable limit of Indian drinking water standards IS 10500, 1999). In five habitations (11%), fluoride concentration in groundwater is at toxic level (viz. above 3.0 mg/l). The maximum fluoride concentration in the block is 5.91 mg/l from Sirsi village. As per the desirable and maximum permissible limit for fluoride in drinking water, determined by World Health Organization or by Bureau of Indian Standards, the groundwater of about 13 habitations of the studied sites is unfit for drinking purposes. Due to the higher fluoride level in drinking water, several cases of dental and skeletal fluorosis have appeared at alarming rate in this region. There is an instant need to take ameliorative steps in this region to prevent the population from fluorosis. Groundwater sources of block Nawa can be used for drinking after an effective treatment in absence of other safe source. The evaluation of various defluoridation methods on the basis of social and economical structure of India reveals that the clay pot chip, activated alumina adsorption, and Nalgonda techniques are the most promising.     

Prevalence of certain inorganic constituents in groundwater samples of Erode district, Tamilnadu, India, with special emphasis on fluoride, fluorosis and its remedial measures

A total of 60 drinking water samples collected from Erode district, Tamilnadu, India were analysed for fluoride contamination, besides water quality parameters such as pH, electrical conductivity, total dissolved solids, total alkalinity, total hardness, fluoride, bicarbonates, calcium, magnesium, nitrate, sulphate, phosphate, sodium and potassium. The results obtained were found to exceed the permissible limits. The concentration of fluoride in the water samples ranged between 0.5 and 8.2 mg/l and revealed that 80% of the water samples contain fluoride above the maximum permissible limit. Similarly, the concentrations of nitrate, hardness, calcium and magnesium in some samples were also more than the permissible level. Pearson’s correlation coefficient among the parameters showed a positive correlation of fluoride with total hardness and calcium. It is inferred from the study that these water sources can be used for potable purpose only after prior treatment.     

The impact of a disused mine on uranium transport in the River Fal, South West England

Unfiltered and filtered (0.45 and 0.2 microm) water samples and sediment samples (sieved to <180 microm and 180-1000 microm) were collected along an approximately 15 km transect of the River Fal, Cornwall, UK, to examine the impact of the disused South Terras uranium mine on the uranium concentrations of the river water and underlying sediments. The uranium concentration of the water samples fluctuated along the river, with the 0.45 microm filtered water showing the largest, seven-fold, difference between minimum (0.19 microg L(-1)) and maximum (1.34 microg L(-1)) concentrations. The historical uranium mine and spoil heaps were not a significant source of uranium to the river water, as water concentrations were low next to the site, but a highly elevated uranium concentration (1000 mg kg(-1)) was found in sediment below an outflow pipe from this mine. Operationally defined "colloidal" (0.2-0.45 microm) and "dissolved" (<0.2 microm) uranium were the predominant forms of the element in the river water (35 and 45% respectively). The uranium concentration in the dissolved phase showed a correlation coefficient of 0.83 (n= 9) with the total cation concentration, suggesting that the uranium concentration in this fraction is directly linked to weathering of rocks and minerals. The observation that weathering is the dominant mechanism delivering uranium to the river water explains the low uranium concentrations in the river water close to South Terras mine, despite the proximity of the spoil heaps, and the maximum uranium concentrations close to a china clay mining area.     

Nitrate,sulphate and chloride contents in public drinking water supplies in Sicily,Italy

Water samples collected from public drinking water supplies in Sicily were analysed for electric conductivity and for their chloride, sulphate and nitrate contents. The samples were collected as uniformly as possible from throughout the Sicilian territory, with an average sampling density of about one sample for every 7,600 inhabitants. Chloride contents that ranged from 5.53 to 1,302 mg/l were correlated strongly with electric conductivity, a parameter used as a proxy for water salinity. The highest values are attributable to seawater contamination along the coasts of the island. High chloride and sulphate values attributable to evaporitic rock dissolution were found in the central part of Sicily. The nitrate concentrations ranged from 0.05 to 296 mg/l, with 31 samples (4.7% of the total) exceeding the maximum admissible concentration of 50 mg/l. Anomalous samples always came from areas of intensive agricultural usage, indicating a clear anthropogenic origin. The same parameters were also measured in bottled water sold in Sicily, and they all were within the ranges for public drinking water supplies. The calculated mean nitrate intake from consuming public water supplies (16.1 mg/l) did not differ significantly from that of bottled water (15.2 mg/l). Although the quality of public water supplies needs to be improved by eliminating those that do not comply with the current drinking water limits, at present it does not justify the high consumption of bottled water (at least for nitrate contents).     

Determination of heavy metal contents in water,sediments, and fish tissues of Shizothorax plagiostomus in river Panjkora at Lower Dir,Khyber Pakhtunkhwa,Pakistan

The present study was conducted to investigate the contamination of water, sediments, and fish tissues with heavy metals in river Panjkora at Lower Dir, Khyber Pakhtunkhwa, Pakistan. Water, sediments, and fish (Shizothorax plagiostomus) samples were collected from September 2012 to January 2013 at three different sites (upstream site at Sharigut, sewage site at Timergara, and downstream site at Sadoo) of river Panjkora. The concentrations of heavy metals in water were in the order Zn?>?Cu?≈?Pb?>?Ni?≈?Cd with mean values of 0.30, 0.01, 0.01, 0.0 and 0.0 mg/l, respectively, which were below the maximum permissible limits of WHO for drinking water. In sediments, heavy metals were found in the order Cu?>?Zn?>?Ni?>?Pb?>?Cd with mean concentrations of 50.6, 38.7, 9.3, 8, and 0.4 mg/kg, respectively. Ni and Cd were not found in any fish tissues, but Zn, Cu, and Pb were detected with the mean concentration ranges of 0.04–1.19, 0.03–0.12, and 0.01–0.09 μg/g, respectively. The present study demonstrates that disposal of waste effluents causes a slight increase in the concentration of heavy metals in river Panjkora as revealed by variation in metal concentrations from upstream to downstream site. Sewage disposal was also found to change physicochemical characteristics of Panjkora water. At present, water and fish of river Panjkora are safe for human consumption, but the continuous sewage disposal may create problems in the future.     

Hydrogeochemical processes controlling the high fluoride concentration in groundwater: a case study at the Boden block area,Orissa, India

The present investigation reports the assessment of hydrochemical/geochemical processes controlling the concentration of fluoride in groundwater of a village in India (Boden block, Orissa). Boden block is one of the severely affected fluoride-contaminated areas in the state of Orissa (India). The sampling and subsequent analysis of water samples of the study area was carried out following standard prescribed methods. The results of the analysis indicate that 36.60% groundwater F⁻ concentration exceeds the limit prescribed by the World Health Organization for drinking water. The rock interaction with groundwater containing high concentration of HCO₃⁻ and Na⁺ at a higher pH value of the medium could be one of the important reasons for the release of F⁻ from the aquatic matrix into groundwater. Geochemical classification of groundwater based on Chadha rectangular diagram shows that most of the groundwater samples having fluoride concentration more than 1.5 mg L⁻¹ belongs to the Na-K-HCO₃ type. The saturation index values evaluated for the groundwater of the study area indicated that it is oversaturated with respect to calcite, whereas the same is undersaturated with respect to fluorite content. The deficiency of calcium ion concentration in the groundwater from calcite precipitation favors fluorite dissolution leading to excess of fluoride concentration. The risk index was calculated as a function of fluoride level in drinking water and morbidity of fluorosis categorizes high risk for villages of Amera and Karlakote panchayat of Boden block.     

Fluoride in groundwater, Varaha River Basin, Visakhapatnam District, Andhra Pradesh, India

Excess intake of fluoride through drinking water causes fluorosis on human beings in many States of the country (India), including Andhra Pradesh. Groundwater quality in the Varaha River Basin located in the Visakhapatnam District of Andhra Pradesh has been studied, with reference to fluoride content, for its possible sources for implementing appropriate management measures, according to the controlling mechanism of fluoride concentration in the groundwater. The area occupied by the river basin is underlain by the Precambrian Eastern Ghats, over which the Recent sediments occur. Results of the chemical data of the groundwater suggest that the considerable number of groundwater samples show fluoride content greater than that of the safe limit prescribed for drinking purpose. Statistical analysis shows that the fluoride has a good positive relation, with pH and bicarbonate. This indicates an alkaline environment, as a dominant controlling mechanism for leaching of fluoride from the source material. Other supplementary factors responsible for the occurrence of fluoride in the groundwater are evapotranspiration, long contact time of water with the aquifer material, and agricultural fertilizers. A lack of correlation between fluoride and chloride, and a high positive correlation between fluoride and bicarbonate indicate recharge of the aquifer by the river water. However, the higher concentration of fluoride observed in the groundwater in some locations indicates insufficient dilution by the river water. That means the natural dilution did not perform more effectively. Hence, the study emphasizes the need for surface water management structures, with people's participation, for getting more effective results.     

Biomonitoring of cadmium, chromium, nickel and arsenic in general population living near mining and active industrial areas in Southern Tunisia

The human health impact of the historic and current mining and industrial activities in Tunisia is not known. This study assessed the exposure to metals in the population of Southern Tunisia, using biomonitoring. The aim of this pilot study was to evaluate metal exposure on 350 participants living near mining and active industrial areas in the South of Tunisia. Blood specimens were analyzed for metals (Cd, Cr, As, and Ni) by Atomic Absorption Spectrometer equipped with Zeeman background correction and AS-800 auto sampler by graphite furnace and graphite tubes with integrated L'vov platform. The sample population was classified according to different age groups, sex, smoking habit, sea food and water drinking consumption, occupational exposure, amalgam fillings and place of residence. The blood As, Cd, Cr and Ni values expressed as mean?±?SD were 1.56?±?2.49, 0.74?±?1.15, 35.04?±?26.02 and 30.56?±?29.96 μg/l, respectively. Blood Cd and Ni levels in smokers were 2 and 1.2 times, respectively, higher than in non-smokers. Blood Cd levels increase significantly with age (p?=?0.002). As, Cd and Ni were significantly correlated with gender and age (p?<?0.05). Cd level in blood samples of subjects occupationally exposed was 1.3 times higher than that of non-exposed. Blood metals were not significantly affected by amalgam fillings, place of living and sea food and drinking water consumption. This first biomonitoring study of metal exposure in the South of Tunisia reveals a substantial exposure to several metals. The pathways of exposure and health significance of these findings need to be further investigated.