Photooxidation of naphthalenesulfonic acids: comparison between processes based on O(3), O(3)/activated carbon and UV/H(2)O(2)

The aim of the present study was to analyze and compare the efficacy of UV photodegradation with that of different advanced oxidation processes (O(3), UV/H(2)O(2), O(3)/activated carbon) in the degradation of naphthalenesulfonic acids from aqueous solution and to investigate the kinetics and the mechanism involved in these processes. Results obtained showed that photodegradation with UV radiation (254 nm) of 1-naphthalenesulfonic, 1,5-naphthalendisulfonic and 1,3,6-naphthalentrisulfonic acids is not effective. Presence of duroquinone and 4-carboxybenzophenone during UV irradiation (308-410 nm) of the naphthalenesulfonic acids increased the photodegradation rate. Addition of H(2)O(2) during irradiation of naphthalenesulfonic acids accelerated their elimination, due to the generation of ()OH radicals in the medium. Comparison between UV photodegradation 254 m and the advanced oxidation processes (O(3), O(3)/activated carbon and UV/H(2)O(2)) showed the low-efficacy of the former in the degradation of these compounds from aqueous medium. Thus, among the systems studied, those based on the use of UV/H(2)O(2) and O(3)/activated carbon were the most effective in the oxidation of these contaminants from the medium. This is because of the high-reactivity of naphthalenesulfonic acids with the *OH radicals generated by these two systems. This was confirmed by the values of the reaction rate constant of *OH radicals with these compounds k(OH), obtained by competitive kinetics (5.7 x 10(9) M(-1) s(-1), 5.2 x 10(9) M(-1) s(-1) and 3.7 x 10(9) M(-1) s(-1) for NS, NDS and NTS, respectively).     

Degradation of the pharmaceutical metronidazole via UV, Fenton and photo-Fenton processes

Degradation rates and removal efficiencies of Metronidazole using UV, UV/H2O2, H2O2/Fe2+, and UV/H2O2/Fe2+ were studied in de-ionized water. The four different oxidation processes were compared for the removal kinetics of the antimicrobial pharmaceutical Metronidazole. It was found that the degradation of Metronidazole by UV and UV/H2O2 exhibited pseudo-first order reaction kinetics. By applying H2O2/Fe2+, and UV/H2O2/Fe2+ the degradation kinetics followed a second order behavior. The quantum yields for direct photolysis, measured at 254 nm and 200-400 nm, were 0.0033 and 0.0080 mol E(-1), respectively. Increasing the concentrations of hydrogen peroxide promoted the oxidation rate by UV/ H2O2. Adding more ferrous ions enhanced the oxidation rate for the H2O2/Fe2+ and UV/H2O2/Fe2+ processes. The major advantages and disadvantages of each process and the complexity of comparing the various advanced oxidation processes on an equal basis are discussed.     

Decomposition of gas-phase trichloroethene by the UV/TiO2 process in the presence of ozone.

The decomposition of gas-phase trichloroethene (TCE) in air streams by direct photolysis, the UV/TiO2 and UV/O3 processes was studied. The experiments were carried out under various UV light intensities and wavelengths, ozone dosages, and initial concentrations of TCE to investigate and compare the removal efficiency of the pollutant. For UV/TiO2 process, the individual contribution to the decomposition of TCE by direct photolysis and hydroxyl radicals destruction was differentiated to discuss the quantum efficiency with 254 and 365 nm UV lamps. The removal of gaseous TCE was found to reduce by UV/TiO2 process in the presence of ozone possibly because of the ozone molecules could scavenge hydroxyl radicals produced from the excitation of TiO2 by UV radiation to inhibit the decomposition of TCE. A photoreactor design equation for the decomposition of gaseous TCE by the UV/TiO2 process in air streams was developed by combining the continuity equation of the pollutant and the surface catalysis reaction rate expression. By the proposed design scheme, the temporal distribution of TCE at various operation conditions by the UV/TiO2 process can be well modeled.     

Phototransformation of ibuprofen and ketoprofen in aqueous solutions

The UV (254 nm) and UV/VUV (254/185 nm) photolysis of two anti-inflammatory drugs, ibuprofen and ketoprofen, have been studied in aqueous solutions as a possible process for the removal of non-biodegradable compounds.We have examined the effects of dissolved oxygen and initial target concentration. Upon irradiation at 254 nm, the decomposition rate of ketoprofen is almost forty times higher as it of ibuprofen whilst VUV irradiation only increased the ibuprofen decomposition rate. The presence of dissolved oxygen accelerated the photodegradation of ibuprofen, whereas no effect was observed on the degradation of ketoprofen. The maximum quantum yield for the phototransformation was 0.2. The rate of mineralization in both cases was ∼60%, even after 1 h of treatment and this suggests the formation of stable by-products which were identified using GC-MS and HPLC-MS, respectively.     

The degradation of endocrine disruptor di-n-butyl phthalate by UV irradiation: a photolysis and product study

The direct photolysis of an important endocrine disruptor compound, di-n-butyl phthalate (DBP), has been investigated under monochromatic UV irradiation at 254 nm over a wide pH range (3-11). The investigation was carried out under idealized conditions and has considered both reaction kinetics and the degradation mechanism. It was found that more than 90% of DBP can be degraded within an hour of irradiation in water. A simple model has been developed and used to predict the initial DBP photolysis rate constant at different pH values and initial DBP concentrations. The major decomposition mechanism of DBP is believed to involve the hydrolytic photolysis of the carbon in the alpha and/or beta-position of the ester chain with the production of aromatic carboxylic derivatives. Additionally, multi-degradation pathways are proposed for acid-catalyzed hydrolytic photolysis (pH 3-5), which was found to be useful in explaining the photo-degradation of DBP under acidic conditions. The use of 254 nm UV to photo-degrade DBP was found to be a relatively fast and clean process, especially in neutral to basic conditions.     

Biodegradability and toxicity assessment of trans-chlordane photochemical treatment

The removal of trans-chlordane (C(10)H(6)Cl(8)) from aqueous solutions was studied using UV, UV/H(2)O(2), UV/H(2)O(2)/Fe(2+), UV/TiO(2), or UV/TiO(2)/H(2)O(2) treatment using either UV/Vis blue lamps or UVC lamps (254 nm). H(2)O(2), FeSO(4) and TiO(2) were added at 1700, 456, and 2500 mgL(-1), respectively. trans-Chlordane was not significantly removed in non-irradiated controls and in samples irradiated with UV/Vis. It was also not removed in the absence of surfactant Triton X-114 added at 250 mgL(-1). In the presence of the surfactant, trans-chlordane concentration was reduced by 95-100% after 48 h of UVC and UVC/H(2)O(2) treatments and 70-80% after UVC/H(2)O(2)/Fe(2+), UVC/TiO(2) and UVC/H(2)O(2)/TiO(2) treatments. Based on these results, UVC, UVC/H(2)O(2) and UVC/TiO(2) treatments were further investigated. UVC treatment supported the highest pollutant removal (100% in 48 h), dechlorination efficiency (81% in 48 h), and detoxification to Lepidium sativum seed germination and activated sludge respiration although irradiated samples remained toxic to Chlorella vulgaris. Biodegradation of the UVC irradiated samples removed the source of algae toxicity but this could not be clearly attributed to the removal of trans-chlordane photoproducts because the surfactant interfered with the chemical and biological assays. Evidence was found that trans-chlordane was photodegraded through photolysis causing its successive dechlorination. trans-Chlordane removal was well described by a first order kinetic model at a rate of 0.21±0.01h(-1) at the 95% confidence interval.     

Photochemical and photocatalytic degradation of gaseous toluene using short-wavelength UV irradiation with TiO2 catalyst: comparison of three UV sources

The feasibility of the use of short-wavelength UV (254+185 nm) irradiation and TiO2 catalyst for photodegradation of gaseous toluene was evaluated. It was clear that the use of TiO2 under 254+185 nm light irradiation significantly enhanced the photodegradation of toluene relative to UV alone, owed to the combined effect of photochemical oxidation in the gas phase and photocatalytic oxidation on TiO2. The photodegradation with 254+185 nm light irradiation was compared with other UV wavelengths (365 nm (black light blue lamp) and 254 nm (germicidal UV lamp)). The highest conversion and mineralization were obtained with the 254+185 nm light. Moreover, high conversions were achieved even at high initial concentrations of toluene. Catalyst deactivation was also prevented with the 254+185 nm light. Regeneration experiments with the deactivated catalyst under different conditions revealed that reactive oxygen species played an important role in preventing catalyst deactivation by decomposing effectively the less reactive carbon deposits on the TiO2 catalyst. Simultaneous elimination of photogenerated excess ozone and residual organic compounds was accomplished by using a MnO2 ozone-decomposition catalyst to form reactive species for destruction of the organic compounds.     

Gas phase trichloroethylene (TCE) photooxidation and byproduct formation: photolysis vs. titania/silica based photocatalysis

Photooxidation of trichloroethylene (TCE) was examined in comparative study using photolysis and photocatalysis. Degussa P25 titania coated on reactor wall and deposited on silica based microporous support were used as photocatalyst. The destruction of TCE and formation of potential byproducts were investigated under steady state conditions using annular photoreactors. Experimental work involved passing polluted air containing TCE through the UV photoreactor at varying concentrations and residence times. Ultraviolet illumination was provided by low pressure mercury lamps with outputs at either 254 nm, 365 nm, or 185/254 nm. Silica supported photocatalyst yielded maximum removal capacity of up to about 6 kg TCE per m3 per hour, nearly twice that provided by the coated titania. Direct photolysis with ozone generating UV also provided very high TCE conversion of up to 6kg TCE per m3 per hour. However, major quantities of phosgene and dichloroacetyle chloride (DCAC) were produced as byproducts. TCE removal using silica based photocatalyst did not result in any detectable DCAC. Only phosgene along with trace amounts of chloroform and carbon tetrachloride were identified as oxidation byproducts with silica based photocatalyst.     

An investigation into reservoir NOM reduction by UV photolysis and advanced oxidation processes

A comparison of four treatment technologies for reduction of natural organic matter (NOM) in a reservoir water was made. The work presented here is a laboratory based evaluation of NOM treatment by UV-C photolysis, UV/H(2)O(2), Fenton's reagent (FR) and photo-Fenton's reagent (PFR). The work investigated ways of reducing the organic load on water treatment works (WTWs) with a view to treating 'in-reservoir' or 'in-pipe' before the water reaches the WTW. The efficiency of each process in terms of NOM removal was determined by measuring UV absorbance at 254 nm (UV(254)) and dissolved organic carbon (DOC). In terms of DOC reduction PFR was the most effective (88% removal after 1 min) however there were interferences when measuring UV(254) which was reduced to a lesser extent (31% after 1 min). In the literature, pH 3 is reported to be the optimal pH for oxidation with FR but here the reduction of UV(254) and DOC was found to be insensitive to pH in the range 3-7. The treatment that was identified as the most effective in terms of NOM reduction and cost effectiveness was PFR.     

Comparison of advanced oxidation processes and identification of monuron photodegradation products in aqueous solution

The photodegradation of monuron (3-(4-chlorophenyl)-1,1-dimethylurea) in aqueous solutions under simulated solar irradiation has been conducted by different advanced oxidation processes (UV/H(2)O(2), UV/H(2)O(2)/Fe(2+), UV/H(2)O(2)/TiO(2), UV/TiO(2), dark H(2)O(2)/Fe(3+)). The degradation rates were always higher for the homogeneous catalysis in photo-Fenton reactions (UV/H(2)O(2)/Fe(2+)) compared to the heterogeneous photocatalytic systems (TiO(2)/UV and UV/H(2)O(2)/TiO(2)). Optimal concentrations of Fe(2+) and H(2)O(2) for the abatement of the herbicide in the photo-Fenton system were found to be 1 mM Fe(II) and 10 mM H(2)O(2). Several intermediary products were identified using large volume injection micro-liquid chromatography with UV detection (mu-LC-UV), mu-LC-MS and GC-MS techniques and a degradation mechanism has been proposed.     

利用UVC去除低浓度苯的实验研究

探讨了不同实验参数对苯的UVC去除效果的影响,获得了苯的去除率与苯的初始浓度、气体流量、相对湿度和氧气含量等参数之间的关系。数据表明,在实验条件范围内,苯的去除率的倒数与苯初始浓度、气体流量之间为线性关系;苯的去除率随相对湿度的增加呈现先升高后缓慢降低的关系,最佳相对湿度值在30%～50%之间;苯的去除率随氧气量的增加而缓慢增加;波长为185+254 nm的UV与254 nm的UV相比净化效果更为理想。还分析了苯降解产生的中间产物,探讨了苯的降解机理。     

紫外光(UV)光解油田采出水中多环芳烃

为了探讨紫外光光解人工模拟油田采出水中多环芳烃的降解效率,利用自制反应装置对油田采出水中多环芳烃(PAHs)的紫外光光解做了一个初步研究。研究结果证明,紫外光光解对油田采出水中的多环芳烃萘和芴有显著的降解能力。实验室的测试表明,与紫外UVA(365 nm)、UVB(308 nm)的光照相比,紫外UVC(254 nm)在光照60 min的条件下,2种多环芳烃各自的去除率都近似达到了99%。可见,在光解效力和暴露时间两方面,紫外UVC对采出水中萘和芴的去除具有相对稳定和比较高的效率。     

The direct photolysis and photocatalytic degradation of alachlor at different TiO2 and UV sources

Direct photolysis and photocatalytic degradations of alachlor, a widely used herbicide, were studied using three different monochromatic UV lamps (254, 300 and 350 nm) and two TiO(2) sources. Both the direct photolysis and photocatalytic degradations of alachlor follow pseudo-first-order decay kinetics. TiO(2)-P25 was found to be an effective photocatalyst compared to TiO(2)-BDH. The direct photolysis of alachlor was dominant at 254 nm even if TiO(2) was present in the solution. Among the three UV wavelengths used, the highest photocatalysis quantum yield was obtained at 300 nm. The photocatalytic degradation rate of alachlor increased with the dosages of TiO(2), but an overdose of TiO(2) would retard the reaction due to light attenuation. Photocatalytic reactions were slightly enhanced in an alkaline medium, and the different proton sources causing various degrees of rate retardation were due to the presence of the corresponding counter anions. This effect was diminished at a later stage after the reaction intermediates were formed.     

Kinetic studies of endosulfan photochemical degradations by ultraviolet light irradiation in aqueous medium

Kinetic studies of endosulfan photochemical degradation in controlled aqueous systems were carried out by ultraviolet light irradiation at lambda = 254 nm. The photolysis of (alpha + beta: 2 + 1) endosulfan, alpha-endosulfan and beta-endosulfan were first-order kinetics. The observed rate constants obtained from linear least-squares analysis of the data were 1 x 10(-4) s(-1); 1 x 10(-4) s(-1); and 2 x 10(-5) s(-1), respectively, and the calculated quantum yields (phi) were 1, 1 and 1.6, respectively. Preliminary differential pulse polarographic (DPP) analysis allowed to observe the possible endosulfan photochemical degradation pathway. This degradation route involves the formation of the endosulfan diol, its transformation to endosulfan ether and finally the ether's complete degradation by observing the potential shifts.     

Photolysis of low concentration H2S under UV/VUV irradiation emitted from microwave discharge electrodeless lamps

The photolysis of simulating low concentration of hydrogen sulfide malodorous gas was studied under UV irradiation emitted by self-made microwave discharge electrodeless lamps (i.e. microwave UV electrodeless mercury lamp (185/253.7 nm) and iodine lamp (178.3/180.1/183/184.4/187.6/206.2 nm)). Experiments results showed that the removal efficiency (eta H2S) of hydrogen sulfide was decreased with increasing initial H2S concentration and increased slightly with gas residence time; H2S removal efficiency was decreased dramatically with enlarged pipe diameter. Under the experimental conditions with pipe diameter of 36 mm, gas flow rate of 0.42 standard l s(-1), eta H2S was 52% with initial H2S concentration of 19.5 mg m(-3) by microwave mercury lamp, the absolute removal amount (ARA) was 4.30 microg s(-1), and energy yield (EY) was 77.3 mg kW h(-1); eta H2S was 56% with initial H2S concentration of 18.9 mg m(-3) by microwave iodine lamp, the ARA was 4.48 microg s(-1), and the EY was 80.5mg kW h(-1). The main photolysis product was confirmed to be SO4(2-) with IC.     

Degradation of gas-phase propylene glycol monomethyl ether acetate by ultraviolet/ozone process: A kinetic study

A pilot-scale plug-flow reactor was built to investigate its performance in treating airborne propylene glycol monomethyl ether acetate (PGMEA) via ozonation, ultraviolet (UV) photolysis and UV/O3 technologies. Governing factors, such as the initial molar ratio of ozone (O3) to PG-MEA, UV volumetric electric power input, and moisture content in the influent airstream, were investigated. A 1-L batch reactor was used to investigate some photodegradation characteristics of PGMEA in advance. Experiments were conducted at a fixed influent PGMEA concentration of approximately 50 ppm and an ambient temperature of 26 degrees C. A gas space time of 85 sec in the plug-flow reactor was kept for either ozonation or photolysis reaction, whereas a gas space time of 170 sec was used for the UV/O3 degradation. Results show that an initial molar ratio of O3 to PGMEA of >2.91 and an UV volumetric electric input power of 0.294 W/L(-1) sufficed to obtain PGMEA decompositions of >90% by UV/O3. Kinetic analyses indicate that all types of PGMEA decomposition are pseudo-first order with respect to its concentration. Moisture content (relative humidity = 15-99%) and UV volumetric electric input power (0.147 and 0.294 W/L(-1)) were major factors that strongly affect the PGMEA degradation rate.     

Homogeneous degradation of 1,2,9,10-tetrachlorodecane in aqueous solutions using hydrogen peroxide, iron and UV light

The homogeneous degradation of the polychlorinated n-alkane, 1,2,9,10-tetrachlorodecane (T4C10), was studied in aqueous solutions of hydrogen peroxide, including Fenton and photo-Fenton reaction conditions. All solutions were adjusted to a pH of 2.8 and an ionic strength of 0.1 M NaClO4 prior to photolysis. T4C10 (2 x 10(-6) M) was substantially degraded by the H2O2/UV system (1.0 x 10(-2) M H2O2), with 60% disappearance in 20 min of irradiation in a photoreactor equipped with 300 nm lamps of light intensity 3.6 x 10(-5) Ein L(-1) min(-1) (established by ferrioxalate actinometry). The reaction produced stoichiometric amounts of chloride ion indicating complete dechlorination of the chlorinated n-alkane. T4C10 degraded very slowly under Fenton (Fe2+/H2O2/dark) and Fenton-like (Fe3+/H2O2/dark) conditions. However, when the same solutions were irradiated, T4C10 degraded more rapidly than in the H2O2/UV system, with 61% disappearance in 10 min of exposure. The rapid degradation is related to the enhanced degradation of hydrogen peroxide to oxidizing *OH radicals under photo-Fenton conditions. Degradation was inhibited in both the H2O2/UV and photo-Fenton systems by the addition of KI and tert-butyl alcohol due to *OH scavenging.     

Evaluation of photolysis and hydrolysis of atrazine and its first degradation products in the presence of humic acids

Relative importance of hydrolysis and photolysis of atrazine and its degradation products in aqueous solutions with dissolved humic acids (HA) has been assessed under exposure to sunlight and under UV irradiation. Quantum yield for direct photolysis of atrazine at 254 nm was 0.037 mol photon(-1), the reaction order was 0.8. Atrazine, desethylatrazine and desisopropylatrazine converted to their 2-hydroxy analogs with rate constants 0.02-0.08 min(-1) in clear solutions, while addition of HA (300 mg L(-1)) caused a 10-fold increase in rate constants. Hydroxyatrazine was not degraded. No evidence of photo-Fenton reaction was found. Under exposure to solar light, atrazine, desethylatrazine and desisopropylatrazine were converted to 2-hydroxy analogs only at pH 2 because of acid hydrolysis and possible contribution of photolysis. At lower HA concentration, only their light-shielding effect was noticed, while at higher concentrations, HA-catalysed hydrolysis prevailed. Hydroxyatrazine concentration diminished at all pH values in solutions without HA exposed to sunlight.     

Synergy of ozonation and photocatalysis to mineralize low concentration 2,4-dichlorophenoxyacetic acid in aqueous solution

Concentration of 2,4-dichlorophenoxyacetic acid (2,4-D) may affect its degradation kinetics in advanced oxidation systems, and combinations of two or more systems can be more effective for its mineralization at low concentration levels. Degradations and mineralizations of 0.045mM 2,4-D using O(3), O(3)/UV, UV/TiO(2) and O(3)/UV/TiO(2) systems were compared, and influence of reaction temperature on the mineralization in O(3)/UV/TiO(2) system was investigated. 2,4-D degradations by O(3), O(3)/UV and UV/TiO(2) systems were similar to the results of earlier investigations with higher 2,4-D concentrations. The degradations and total organic carbon (TOC) removals in the four systems were well described by the first-order reaction kinetics. The degradation and removal were greatly enhanced in O(3)/UV/TiO(2) system, and further enhancements were observed with larger O(3) supplies. The enhancements were attributed to hydroxyl radical (()OH) generation from more than one reaction pathway. The degradation and removal in O(3)/UV/TiO(2) system were very efficient with reaction temperature fixed at 20 degrees C. It was suspected that reaction temperature might have influenced ()OH generation in the system, which needs further attention.     

Determination of quantum yields for the photolysis of Fe(III)-hydroxo complexes in aqueous solution using a novel kinetic method

The determination of quantum yields for the photolysis of Fe(III)-hydroxo complexes is important for the quantitative investigation of hydroxyl radical (*OH) production, not only in a natural water body, but also in the photo-Fenton process. A novel kinetic method, using a *OH probe compound, was established for the determination of the quantum yields in this study. The method was based on measuring the pseudo-first-order rate constant of the photodecomposition of dimethylsulfoxide (DMSO) in which DMSO and its primary products scavenged the *OH at an identical rate. The preliminary experiments for the photodecomposition kinetics supported the suitability of DMSOs as a probe compound for determining quantum yields. The individual quantum yields for the photolysis of the monomeric Fe(III) complexes, in the wavelength range 240-380 nm, were determined by the photodecomposition kinetics of the hydroxyl radical (*OH) probe compound (DMSO). The determined values of the individual quantum yields were 0.046+/-0.00052 for Fe3+ (H2O)6 (hexaaquo ion) and 0.69+/-0.025 for Fe(OH)2+ (H2O)5 (hydroxypentaaquo ion) at 254 nm, and showed decreasing values with increasing wavelength, in the ranges of 240-380 nm. The quantum yields between 240 and 280 nm were newly reported in this study, and the values obtained between 280 and 380 nm were in good agreement with the literature values.