Determination of chlorine in air with the pyridine-pyrazolone reagent

An improved method for the determination of chlorine in air is described. The principle of this method is based on the absorption of chlorine in p-toluenesulfonamide aqueous solution, followed by color development with a pyridine-pyrazolone reagent. Both the chlorine absorbed in the solution and the color developed with the reagent were stable. Positive interference by nitrogen dioxide was not observed.     

A Portable Fiber-Optic Chemical Device for the Quantitative Determination of Carbon Monoxide from Automobile Exhaust Emissions

ABSTRACT

A colorimetxic method for the quantitative determination of CO by diffuse reflectance is described. This method is based on the reduction by CO of Mo (VI) from the indicator reagent molybdosilicic acid (H₈Si[Mo₂O₇]₆). The reduction yielded a change of color from clear yellow to dark green on white disk filter chart paper wetted with reagent indicator solution. The gaseous mixture containing CO was forced to pass through this chart paper, initiating the reaction. The intensity of the color produced, measured by diffuse reflectance, was proportional to the CO concentration present in exhaust gases in the range from 0.02 to 12% volume/volume (v/v). A 650-nm light-emitting diode was used as a light source. A two-fiber-optic system carried the light from the source to the detection system, which was composed of a photodiode, an amplification circuit, and a digital display. The method was applied with success in field measurements for automobiles in the Otto cycle. In a previous paper, this method was used for the quantitative determination of exhaust emissions from diesel-fueled vehicles.¹     

Evaluation of Contact Columns for Nitrogen Dioxide Absorption

The absorption efficiencies of 6–, 10–, IS–, and 60-turn spiral contact columns for two formulations of Saltzman reagent are evaluated for use in atmospheric nitrogen dioxide analyzers at several air and liquid flow rates. Response times for the several columns as a function of flow rates and absorbing reagent are also given. The recommended column and reagent are indicated. The technique of adjusting instrument parameters for direct readout of NO₂ concentrations is described.     

An Inspection Method for Automobile Hydrocarbon Emission

A quick, simple method for identifying and distinguishing lead from other heavy metals in living plants has been developed using sodium rhodizonate (C₆0₆Na₂) which forms a scarlet precipitate with lead at approximately pH 2.8. Hand sections of plant tissues are treated with rhodizonate reagent, buffered, and examined microscopically. Very little time and/or effort is required for this method. Those cells and tissues contaminated with lead turn scarlet—color intensity being directly related to concentration. Lead may be detected in quite low concentrations and, most importantly, may be observed in situ; its entry and movement through the plant can thus be followed. In an area of moderate traffic of Downey, Calif. (Southeast Los Angeles), lead was found abundantly on leaves as well as on and in roots of garden-grown lettuce; origin of this lead is presumed to be from car exhausts.     

Hybrid zero valent iron (ZVI)/H2O2 oxidation process for landfill leachate treatment with novel nanosize metallic calcium/iron composite

A novel nanosize metallic calcium/iron dispersed reagent was synthesized and tested as coagulant/catalyst in a hybrid zero valent iron (ZVI)/H₂O₂ oxidation process to treat leachate. Two different types of leachates, one from municipal solid waste (MSW) tipping hall (MSWIL) and second from an MSW landfill site (MSWLL), were collected and characterized. The morphology, elemental composition, and mineral phases of the nano-Ca/CaO and nano-Fe/Ca/CaO were characterized by scanning electron microscopy–electron dispersive spectroscopy (SEM-EDS) and x-ray powder diffraction (XRD) analysis. The coagulation process with 2.5 g L^?1 nano-Ca/CaO attained 64.0, 56.0, and 20.7% removal of color, chemical oxygen demand (COD), and total suspended solids (TSS) in MSWLL. With only 1.0 g L^?1 of nano-Fe/Ca/CaO, relatively high color, COD and TSS removal was achieved in MSWLL at 67.5, 60.2, and 37.7%, respectively. The heavy metal removal efficiency reached 91–99% after treatment with nano-Fe/Ca/CaO in both leachate samples. The coupling process, using 1.0 g L^?1 of nano-Fe/Ca/CaO and 20 mM H₂O₂ doses, achieved enhancement removal of color, COD, and TSS, up to 95%, 96%, and 66%, respectively, without initial pH control. After this treatment, the color, COD, TSS, and heavy metals were significantly decreased, fitting the Korean discharge regulation limit. A hybrid coupled zero valent iron (ZVI)/H₂O₂ oxidation process with novel nanosized metallic calcium/iron dispersed reagent proved to be a suitable treatment for dealing with leachate samples.

Implications: Conventional treatments (biological or physicochemical) are not sufficient anymore to reach the level of purification needed to fully reduce the negative impact of landfill leachates on the environment. This implies that new treatment alternatives species must be proposed. A coupled zero valent iron (ZVI)/H₂O₂ oxidation process proved to be a suitable treatment for dealing with leachate samples. Coagulation with nFe/Ca/CaO allows 91–99% of heavy metals removal. The coupled coagulation–oxidation process by nFe/Ca/CaO reveals excellent ability to treat leachate. After coupled treatment the color, COD, and TSS were also much lower than the discharge regulation limit.     

超声降解水中的磺胺嘧啶

以磺胺嘧啶(SD)为研究对象,探讨了超声功率、初始浓度、pH值以及超声协同H2O2、Fenton、TiO2等组合工艺对超声降解SD效率的影响。实验结果表明,超声可有效降解水中低浓度的SD,尤其在酸性条件下,超声降解更为显著,降解过程遵循准二级反应动力学模型。加入H2O2或TiO2可在一定程度上促进SD的超声降解,加入Fenton试剂则显著提升SD的去除率。依据量化计算以及LC-MS测定结果,探讨了SD的超声降解机理。超声降解水中SD主要是基于.OH自由基的氧化过程。     

Public Health Service National Fallout Surveillance Program

A semi-automated method for determination of fluorine in biological materials has been developed incorporating the Technicon AutoAnalyzer. One-half gram of dried, ground plant material is ashed, alkali-fused, diluted with water, and the suspension is pumped, along with H₂SO₄, at controlled rates, into the hot revolving glass helix of a digestor unit. As the acid-digest mixture passes through the heated coil, volatile fluoride and water vapor are evolved. The volatile fluoride and water vapor are pulled from the helix under reduced pressure through a tube which projects into the helix. The tube, in turn, is connected to a water-jacketed condenser and then to an impinger where the sample is continuously mixed. An aliquot of the impinger liquid is being constantly withdrawn. This sample is then air-segmented and mixed with a reagent containing alizarin complexone, pH 4 acetate buffer, lanthanum nitrate, acetone, and water. The sample-reagent combination passes through 4 full-length mixing coils where color development takes place. Upon reacting with fluoride, the wine-red alizarin complexone-La(III) reagent forms a lilac blue fluoride complex. The solution is pumped from the mixing coils through the tubular flow cell of the colorimeter. The absorbence of the solution is measured at 624 mμ, and the signal is transmitted to a recorder where the results are plotted on absorbency paper. The absorbence at the apex of the peak is proportional to the amount of fluoride in the sample between the range of 2.5-80 μg °F. Samples are analyzed at a rate of 12 per hour. Results compare favorably with those obtained by Willard-Winter distillation. Recent studies indicate that the F content of plant tissues can be estimated without prior ashing and fusion     

Fenton氧化活性深蓝染料B-2GLN的动力学

为了考查H2O2/Fe2+的摩尔比和H2O2的初始剂量、pH值以及活性深蓝染料B-2GLN(RDB B-2GLN)的初始浓度对活性深蓝染料B-2GLN降解过程的影响,采用在线分光光度法对活性深蓝染料B-2GLN的Fenton氧化过程进行了研究,探讨了其动力学过程,并利用气相色谱-质谱联用分析降解中间产物。结果显示,采用Fenton氧化降解水溶液中活性深蓝染料B-2GLN,在H2O2的剂量为2.635 mmol/L,pH值为2.7,H2O2/Fe2+的摩尔比为37.80和活性深蓝染料B-2GLN的初始浓度16 mg/L的条件下,得到300 s后活性深蓝染料B-2GLN的最大色度去除率为85.04%。水溶液中活性深蓝染料B-2GLN与·OH的反应速率常数为2.62×1011L/(mol·s)。活性深蓝B-2GLN染料的分子结构被Fenton试剂分解而未被完全矿化,同时对活性深蓝染料降解产物进行了分析。在线分光光度法是研究染料色度去除率的一种精确、快速与可行的方法。     

A chamber study of secondary organic aerosol formation by linalool ozonolysis

The formation of secondary organic aerosol (SOA) produced from linalool ozonolysis was examined using a dynamic chamber system that allowed the simulation of ventilated indoor environments. Experiments were conducted under room temperature (22–23 °C) and air exchange rate of 0.67 h^?1. An effort was made to maintain the product of the concentrations of the two reagents constant. The results suggest that under the conditions when the product of the two reagent concentrations was constant, the relative concentrations play an important role in determining the total SOA formed. A combination of concentrations somewhere in ozone limiting region will produce the maximum SOA concentration. The measured reactive oxygen species (ROS) concentrations at linalool and ozone concentrations relevant to prevailing indoor concentrations ranged from 0.71 to 2.53 nmol m^?3 equivalents of H₂O₂. It was found that particle samples aged for 24 h lost a significant fraction of the ROS compared to fresh samples. The residual ROS concentrations were around 15–69%. Compared with other terpene species like α-pinene that has one endocyclic unsaturated carbon bond, linalool was less efficient in potential SOA formation yields.     

Treatment of polychlorinated biphenyls in two surface soils using catalyzed H₂O₂ propagations

Two surface soils contaminated with polychlorinated biphenyls (PCBs) collected from Superfund sites in the New England region of the United States, Fletcher Paints and Merrimack Industrial Metals, were evaluated for field treatment at the bench level using catalyzed H₂O₂ propagations (CHP—modified Fenton’s reagent). The two soils were first evaluated for the potential for in situ treatment based on two criteria: (1) temperature (<40 °C after CHP reagent addition), and (2) hydrogen peroxide longevity (>24 h). In situ CHP remediation was more applicable to the Fletcher soil, while the Merrimack soil was better suited to ex situ treatment based on temperature increases and hydrogen peroxide lifetimes. Using the highest hydrogen peroxide concentrations appropriate for in situ treatment in each soil, PCB destruction was 94% in the Fletcher soil but only 48% in the Merrimack soil. However, 98% PCB destruction was achieved in the Merrimack soil using conditions more applicable to ex situ treatment (higher hydrogen peroxide concentrations with temperatures >40 °C). Analysis of degradation products by gas chromatography/mass spectroscopy showed no detectable chlorinated degradation products, suggesting that the products of PCB oxidation were rapidly dechlorinated and degraded. The results of this research document that the two PCB-contaminated soils studied can be effectively treated using aggressive CHP conditions, and that such a detailed bench study provides important information before implementing field treatment.     

Electrochemical treatment of domestic wastewater using boron-doped diamond and nanostructured amorphous carbon electrodes

The performance of the electrochemical oxidation process for efficient treatment of domestic wastewater loaded with organic matter was studied. The process was firstly evaluated in terms of its capability of producing an oxidant agent (H₂O₂) using amorphous carbon (or carbon felt) as cathode, whereas Ti/BDD electrode was used as anode. Relatively high concentrations of H₂O₂ (0.064 mM) was produced after 90 min of electrolysis time, at 4.0 A of current intensity and using amorphous carbon at the cathode. Factorial design and central composite design methodologies were successively used to define the optimal operating conditions to reach maximum removal of chemical oxygen demand (COD) and color. Current intensity and electrolysis time were found to influence the removal of COD and color. The contribution of current intensity on the removal of COD and color was around 59.1 and 58.8 %, respectively, whereas the contribution of treatment time on the removal of COD and color was around 23.2 and 22.9 %, respectively. The electrochemical treatment applied under 3.0 A of current intensity, during 120 min of electrolysis time and using Ti/BDD as anode, was found to be the optimal operating condition in terms of cost/effectiveness. Under these optimal conditions, the average removal rates of COD and color were 78.9?±?2 and 85.5?±?2 %, whereas 70 % of total organic carbon removal was achieved.     

MnO2催化Fenton试剂降解苯酚废水

实验对MnO2催化Fenton试剂氧化高浓度苯酚废水的动力学特性和去除效果进行了研究。结果表明,MnO2可以提高Fenton试剂体系对苯酚的降解率以及COD的去除率;Fenton试剂以及MnO2催化Fenton试剂氧化苯酚废水体系中苯酚的降解都符合拟一级动力学模型。在MnO2催化Fenton试剂氧化体系中,苯酚的降解速率常数有明显提高,反应活化能也有所降低,说明MnO2的加入可以使反应容易进行。废水降解前后紫外可见吸收光谱和红外谱图表明,Fenton试剂法将苯酚可能降解为羧酸、烯烃等有机物中间体。     

改进彩管行业含铬废水处理工艺

针对彩管行业含铬废水处理工艺存在的不足,分别从还原剂和混凝剂两方面进行改进.通过比较和分析,最终提出了采用FeSO4作为还原剂处理含铬废水,氧化还原反应pH调节范围扩大,运行安全系数提高;利用新型高效混凝剂配合泥回流工艺,化学药品用量大幅下降,出水COD和SS含量显著减少.     

改进彩管行业含铬废水处理工艺

针对彩管行业含铬废水处理工艺存在的不足,分别从还原剂和混凝剂两方面进行改进。通过比较和分析,最终提出了采用FeSO4作为还原剂处理含铬废水,氧化还原反应pH调节范围扩大,运行安全系数提高;利用新型高效混凝剂配合泥回流工艺,化学药品用量大幅下降,出水COD和SS含量显著减少。     

An Integrated Manual Impinger Method for The Simultaneous Determination of NOx and SOx in Source Effluents

A manual procedure Is outlined which utilizes an alkaline permanganate sampling train for the simultaneous collection of nitrogen and sulfur oxides from stationary sources. Dependent on anticipated concentrations, samples of up to an hour duration may be taken. Analysis of the collected NO_x and SO_x is straightforward, tailored for needed accuracy and minimum employment time. For oxides of nitrogen, the formed nitrites of collection are converted to nitrates. The total nitrate is then reduced to nitrite, diazotized and coupled to form a red dye. This is all accomplished with a commercially available "ready-made" reagent. The oxides of sulfur are determined by the turbidimetric barium sulfate procedure. Data are shown comparing the proposed method from numerous types of emission sources, both with accepted methods and newer instrumental techniques. The ability to sample simultaneously for NO_x and SO_x has many advantages, i.e., power plants, boilers, and other sources where both gases are of interest for compliance and/or source Inventory purposes.     

采用双氰胺甲醛缩聚物混凝去除水中酸性红B染料的研究

以双氰胺和甲醛为原料制备了聚合双氰胺甲醛,并对其进行红外光谱表征.采用聚合双氰胺甲醛与硫代硫酸钠共同作用对酸性红B染料溶液进行混凝脱色实验.对比了单独使用聚合双氰胺甲醛,以及聚合双氰胺甲醛与硫代硫酸钠共同作用的脱色效果.探讨了硫代硫酸钠和聚合双氰胺甲醛的用量以及pH值对脱色率的影响.结果表明,投加硫代硫酸钠可以明显地提高聚合双氰胺甲醛的脱色率,增大絮凝范围,使絮凝剂对pH值的变化有很强的适应性,pH值为7～12的范围内,脱色率均能维持在96%以上.此外,还对混凝脱色的机理进行了研究.     

铁炭微电解/Fenton试剂预处理土霉素废水的研究

研究了铁炭微电解/Fenton试剂法工艺对高浓度难生化处理的土霉素废水预处理效果.结果表明,当原水COD在6 000 mg/L、pH值为2.2时,铁炭微电解反应时间为80 min,铁炭微电解对原水COD的去除率>40%;铁炭微电解出水再投加220 mg/L的H2O2(30%)进行Fenton试剂法处理,常温下反应50 min对原水COD的去除率可提高到75%以上.铁炭微电解 Fenton试剂联合工艺的处理效果好、运行稳定、成本低廉,适宜对难降解的土霉素废水的预处理.     

Fenton试剂法降解餐厨垃圾异味

自行设计Fenton试剂法降解还原性气体异味的反应器,研究了Fenton试剂法处理餐厨垃圾异味主要成分(苯、乙酸乙酯、苯乙烯)的降解效果。以苯为典型代表物,优化得出该实验的最佳反应条件为:pH=3,FeSO4.7H2O投加量为1 g/L液相,30%H2O2投加量为10 mL/L液相,紫外光源辅助。结果证明,Fenton试剂法处理单一异味气体的效果较理想,在前180 min内能达到90%以上,该法在处理气态异味污染物方面具有广阔的应用前景。     

Development of regenerative dye impregnated mesoporous silica materials for assessing exposure to ammonia

The mesostructured materials MCM-41 and SBA-15 were studied as possible supports of bromocresol green (BG) dye impregnation for the ammonia gas detection because of their large surface area, high regenerative property, and high thermal stability. X-ray diffraction, transmission electron microscopy, scanning electron microscope, and N₂ adsorption analysis were used to characterize the prepared materials. These materials could sense ammonia via visible color change from yellowish-orange to blue color. The color change process of the nanostructured materials was fully reversible during 10 cyclic tests. The results indicated that the ammonia absorption responses of the two nanostructured materials were both very sensitive, and high linear correlation and high precision were achieved. As the gaseous ammonia concentrations were 50 and 5 ppmv, the response times for the SBA-15/BG were only 1 and 5 min, respectively. Moreover, the BG dye-impregnated SBA-15 was less affected by the variation in the relative humidity. It also had faster response for the detection of NH₃, as well as lower manufacturing price as compared to that of the dye-impregnated MCM-41. Such feature enables SBA-15/BG to be a very promising material for the detection of ammonia gas.

Implications: The detector tube is a convenient ambient ammonia detection device. However, almost all the commercial detector tubes can be used once only, which not only increases the purchase cost but also produces lots of waste. In this study, we developed two sensing materials that are sensitive for repeated usage. The two mesoporous silica-based materials, MCM-41 and SBA-15, are impregnated by an organic dye of bromocresol green to induce color change behavior that can be easily observed by the naked eye, and it is concluded that dye-impregnated SBA-15/BG is a very promising material for the detection of ammonia gas.     

Lactate oxidation in pyrite suspension: a Fenton-like process in situ generating H2O2

Pyrite is a common mineral at many mining sites. In this study, the mineral pyrite was studied as a Fenton-like reagent for environmental concerns. We selected lactate as a model target molecule to evaluate the Fenton-like catalytic efficiency of pyrite upon organic oxidation. A complete set of control experiments in both aerobic and anaerobic atmospheres unequivocally established that the pyrite in aqueous solution could spontaneously in situ generate OH and H₂O₂, serving as a Fenton-like reagent to catalyze the oxidation of lactate to pyruvate with no need for additional H₂O₂. We called it the pyrite-only Fenton-like (PF) reagent. Monitoring concentration changes of lactate and pyruvate with the time indicated that the pyrite mediated the favorable pyruvate formation at pH 4.5, 60 °C, under air atmosphere. The PF reaction could be stimulated by visible light illumination. Under the optimum conditions, up to 50% of lactate was degraded within 10 d. The results suggest that pyrite and its Fenton-like processes may be potentially practical in wastewater treatment.