Size resolved chemical mass balance of aerosol particles over rural Hungary

The mass size distribution of atmospheric aerosol particles was determined by means of an electric low pressure impactor (ELPI) in rural air in Hungary. The particles captured on different stages of the impactor were chemically analyzed by capillary zone electrophoresis to quantify ionic components as well as by catalytic combustion method to detect total carbon in the samples. The results show that fine aerosol consists mainly of ammonium sulfate and organic carbon. These two species have rather different size distributions since very small particles are composed almost of carbon compounds. The analysis of fine aerosol samples collected simultaneously on filters indicates that an important part of organics is soluble in water. The mass balance of fine particles as a function of their size is estimated by taking into account the liquid water adsorbed by ammonium sulfate and by converting the mass of carbon to the mass of carbon compounds. Finally, the size resolved mass balance of fine aerosol particles is presented and discussed as a function of the origin of air masses.     

Size distribution and sources of aerosol in Launceston, Australia, during winter 1997

As part of a pilot study into the chemical and physical properties of Australian fine particles, a suite of aerosol samples was collected at Ti Tree Bend in Launceston, Tasmania, during June and July 1997. This period represents midwinter in the Southern Hemisphere, a period when aerosol sources in Launceston are dominated by smoke from domestic wood burning. This paper describes the results from this measurement campaign, with the aim of assessing the effect of wood smoke on the chemical and physical characteristics of ambient aerosol. A micro orifice uniform deposit impactor (MOUDI) was used to measure the size distributions of the aerosol from 0.05 to 20 microns aerodynamic diameter. Continuous measurements of fine particle mass were made using a PM2.5 tapered element oscillating microbalance (TEOM) and light scattering coefficients at 530 nm were measured with nephelometers. Mass size distributions tended to be bimodal, with the diameter of the dominant mode tending to smaller sizes with increases in total mass. Non-sea salt potassium and polycyclic aromatic hydrocarbons (PAHs) were used as chemical tracers for wood smoke. Wood smoke was found to increase absolute particle mass (enough to regularly exceed air quality standards), and to concentrate mass in a single mode below 1 micron aerodynamic diameter. The acid-base equilibrium of the aerosol was altered by the wood smoke source, with free acidity hydrogen ion, non-sea salt sulfate, and ammonium concentrations being higher and the concentration of all species, including nitrate (to differing extents), focused in the fine particle size ranges. The wood smoke source also heavily influenced the aerosol scattering efficiency, adding to a strong diurnal cycle in both mass concentration and light scattering.     

The modality of particle size distributions of environmental aerosols

Knowledge of the distribution of airborne particulate matter into size fractions has become an increasing area of focus when examining the effects of air pollution. While total number and mass concentrations may play an important role in exposure and risk assessment analyses, often an understanding of the particle size distributions provides more information on the type of atmospheric processes resulting in the distributions. The modality of the particle size distribution is one such aspect that has been associated with the aerosol formation mechanisms. The aim of this work is to provide a detailed analysis of the modal characteristics of a large number of particle size spectra collected over a period of three years for a range of ambient aerosol types. Measurements of over 6000 size distributions in the size range 0.016–30 μm were made using a scanning mobility particle sizer and an aerodynamic particle sizer for various ambient aerosols including: traffic influenced, urban, vegetation burning influenced, marine, modified background and suburban. Advanced data analytical procedures were adopted to combine the distributions from the two instruments for the calculation of the volume size distributions to allow clear interpretation of the modal characteristics. It was determined that, while in most cases there is a distinct nuclei mode in the number size distribution, this does not translate to a nuclei mode in the volume size distribution. Furthermore, while many of the number size distributions were different for each aerosol studied, the volume distributions were similar. This finding has serious implications for the setting of mass-based air quality standards.     

Size Distribution and Sources of Aerosol in Launceston,Australia, during Winter 1997

ABSTRACT

As part of a pilot study into the chemical and physical properties of Australian fine particles, a suite of aerosol samples was collected at Ti Tree Bend in Launceston, Tasmania, during June and July 1997. This period represents midwinter in the Southern Hemisphere, a period when aerosol sources in Launceston are dominated by smoke from domestic wood burning. This paper describes the results from this measurement campaign, with the aim of assessing the effect of wood smoke on the chemical and physical characteristics of ambient aerosol. A micro orifice uniform deposit impactor (MOUDI) was used to measure the size distributions of the aerosol from 0.05 to 20 n m aerodynamic diameter. Continuous measurements of fine particle mass were made using a PM_2.5 tapered element oscillating microbalance (TEOM) and light scattering coefficients at 530 nm were measured with nephelometers.

Mass size distributions tended to be bimodal, with the diameter of the dominant mode tending to smaller sizes with increases in total mass. Non-sea salt potassium and polycyclic aromatic hydrocarbons (PAHs) were used as chemical tracers for wood smoke. Wood smoke was found to increase absolute particle mass (enough to regularly exceed air quality standards), and to concentrate mass in a single mode below 1 μm aerodynamic diameter. The acid-base equilibrium of the aerosol was altered by the wood smoke source, with free acidity hydrogen ion, non-sea salt sulfate, and ammonium concentrations being higher and the concentration of all species, including nitrate (to differing extents), focused in the fine particle size ranges. The wood smoke source also heavily influenced the aerosol scattering efficiency, adding to a strong diurnal cycle in both mass concentration and light scattering.     

Chemical species’ contributions to the upper extremes of aerosol fine mass

Frequency distributions of the major chemical components of aerosol fine mass are shown to illustrate the respective species’ contributions to the range of observed fine particle mass concentration. The magnitude of a species’ contribution to the upper extremes of aerosol fine mass is relevant to control scenarios that seek to improve worst day fine particle conditions, or in many cases worst day visibility. We summarize the relative contributions of fine particle sulfate, nitrate, carbon, and soil plus sea salt to the upper extremes of aerosol fine mass based on Interagency Monitoring of PROtected Visual Environments (IMPROVE) data collected at monitoring locations across the United States during 1995 through 1999. The data show that the spatial pattern of a given chemical species’ contribution to the upper extremes of aerosol fine mass is often quite different than at lower fine mass concentrations. In some cases, the monitoring data suggest a casual relationship between specific aerosol source regions and the magnitude in which a species’ contribution to the upper extremes of fine mass is elevated above the contribution to median fine mass concentrations.     

Variation of mass scattering efficiencies in IMPROVE

The Interagency Monitoring of Protected Visual Environments (IMPROVE) equation used to assess compliance under the U.S. Environmental Protection Agency (EPA) Haze Rule assumes that dry mass scattering efficiencies for aerosol chemical components are constant. However, examination of aerosol size distributions and chemical composition during the Big Bend Regional Aerosol and Visibility Observational Study and the Southeastern Aerosol and Visibility Study suggests that volume and mass scattering efficiencies vary directly with increasing particle light scattering and aerosol mass concentration. This is consistent with the observation that particle distributions were shifted to larger sizes under more polluted conditions and appears to be related to aging of the aerosol during transport to remote locations.     

Variation of Mass Scattering Efficiencies in IMPROVE

Abstract

The Interagency Monitoring of Protected Visual Environments (IMPROVE) equation used to assess compliance under the U.S. Environmental Protection Agency (EPA) Haze Rule assumes that dry mass scattering efficiencies for aerosol chemical components are constant. However, examination of aerosol size distributions and chemical composition during the Big Bend Regional Aerosol and Visibility Observational Study and the Southeastern Aerosol and Visibility Study suggests that volume and mass scattering efficiencies vary directly with increasing particle light scattering and aerosol mass concentration. This is consistent with the observation that particle distributions were shifted to larger sizes under more polluted conditions and appears to be related to aging of the aerosol during transport to remote locations.     

A fast and efficient modified sectional method for simulating multicomponent collisional kinetics

A fast and efficient method for simulating the evolution of internally mixed multicomponent particle size distributions for aerosol coagulation and droplet coalescence is developed. The technique is based upon a bin-wise sectionalization of the particle mass domain and by imposing the condition of mass conservation for each component. The distribution of each species as a function of the total particle mass is represented in each mass bin as a two-parameter exponential function. Particles of a given mass are assumed to be internally homogeneously mixed. The method is shown to be numerically stable for a wide range of time steps. The numerical solution is compared with both analytical results and results from other well-accepted numerical schemes. This comparison reveals that the proposed technique offers the advantage of being fast and accurate, even for coarse spectral resolution. The method is computationally attractive and easily allows the treatment of ten or more different chemical species in a collisionally evolving particle size distribution. The applicability of the method is demonstrated with several examples: Coalescence growth of multicomponent cloud droplet spectra, coagulation of measured multi-species aerosol particle size distributions, and the simulation of the accumulation mode due to a source of small aerosol particles. The technique is ideally suited for modelling the interaction of microphysics and chemistry in a size-bin resolving aerosol or cloud model.     

Seasonal variation on size distribution and concentration of PAHs in Guangzhou city, China

Size distribution aerosol samples were collected at an urban location of Guangzhou in four seasons of 2003-2004 by a MOUDI (Micro-orifice Uniform Deposit Impactor). The particle loading (PM10: 80-397 microg m(-3)) was comparable with some other Asia cities; however, much higher than that of Western Europe and North America. Polycyclic aromatic hydrocarbons (PAHs) were measured by gas chromatography with mass selective detector (GC-MS). Seasonal effects on the size distribution of PAHs are presented. Bimode (accumulation and coarse mode) and unimode (accumulation mode) distributions were observed for low-molecule-weight and high-molecule-weight PAHs. A slight shift to larger particles was found for the accumulation mode in autumn and winter, compared with that of spring and summer. One explanation is that the longer aging process of PAHs in autumn and winter would result in volatilization from finer particles followed by condensation onto coarser particles. Another is there was mixing process of local emission with long-range transported aerosol in autumn and winter. The relative higher value of IcdP/(BghiP+IcdP) and lower value of BghiP/BeP in winter also give evidences to the mixing process. The level of PAHs concentration has been much elevated in recent years. This can be attributed to the fast growth of motor vehicle and energy consumption.     

Comparison of black carbon (BC) aerosols in two urban areas – concentrations and size distributions

In this study, the BC aerosol measured at two very different urban sites is compared in terms of concentration, seasonal variation, and size distribution. During a 14 month study, one impactor sample was performed each month on a day with typical meteorological conditions. One (Vienna) or three (Uji) filter samples were obtained during the sampling time of the impactors. BC concentration in both the filter and impactor samples was analyzed with an optical technique (integrating sphere technique), where a calibration curve obtained from commercial carbon black is used to convert the optical signal to BC mass. Gravimetric mass concentration was measured at both sites. The gravimetric mass size distribution was measured only in Vienna. At both sites, the yearly average of the BC concentration on the sampling days was around 5 μg m⁻³. In Vienna, some seasonal trend with high concentrations during the cold season was observed, while in Uji, no pronounced seasonal trend was found. The BC size distribution in Uji was distinctly bimodal in the submicron size range. Log-normal distributions were fitted through the impactor data. The average BC mass median diameters (MMD) of the two submicron modes were 0.15 and 0.39 μm. Each mode contained about the same amount of BC mass. In Vienna only one submicron BC mode (average MMD 0.3 μm) was found because of the low size resolution of the impactor. An analysis of humidity effects on the MMDs of BC (both sites) and gravimetric mass (Vienna only) indicates that the Vienna aerosol is partly mixed internally with respect to BC, while the Uji aerosol seems to be externally mixed.     

The Mass Distribution of Large Atmospheric Particles

This paper describes the results of a study to determine the total mass and the mass distribution of atmospheric aerosols, especially that mass associated with particles greater than 10 μm diameter. This study also determined what fraction of the total aerosol mass a standard high-volume air sampler collects and what fraction and size interval settle out on a dust fall plate. A special aerosol sampling system was designed for this study to obtain representative samples of large airborne particles. A suburban sampling site was selected because no local point sources of aerosols existed nearby. Samples were collected under various conditions of wind velocity and direction to obtain measurements on different types of aerosols.

Study measurements show that atmospheric particulate matter has a bimodal mass distribution. Mass associated with large particles mainly ranged from 5 to 100 μm in size, while mass associated with small particles ranged from an estimated 0.03 to 5 μm in size. Combined, these two distributions produced a bimodal mass distribution with a minimum around 5 μm diameter. The high-volume air sampler was found to collect most of the total aerosol mass, not just that fraction normally considered suspended particulate. Dust fall plates did not provide a good or very useful measure of total aerosol mass. The two fundamental processes of aerosol formation, condensation and dispersion appear to account for the formation of a bimodal mass distribution in both natural and anthropogenic aerosols. Particle size distribution measurements frequently are in error because representative samples of large airborne particles are not obtained. Considering this descrepancy, air pollution regulations should specify or be based upon an upper particle size limit.     

Chemical characterization and source identification/apportionment of fine and coarse air particles in Thessaloniki,Greece

The distribution of air particulate mass and selected particle components (trace elements and polycyclic aromatic hydrocarbons (PAHs)) in the fine and the coarse size fractions was investigated at a traffic-impacted urban site in Thessaloniki, Greece. 76±6% on average of the total ambient aerosol mass was distributed in the fine size fraction. Fine-sized trace elemental fractions ranged between 51% for Fe and 95% for Zn, while those of PAHs were between 95% and 99%. A significant seasonal effect was observed for the size distribution of aerosol mass, with a shift to larger fine fractions in winter. Similar seasonal trend was exhibited by PAHs, whereas larger fine fractions in summer were shown by trace elements. The compositional signatures of fine and coarse particle fractions were compared to that of local paved-road dust. A strong correlation was found between coarse particles and road dust suggesting strong contribution of resuspended road dust to the coarse particles. A multivariate receptor model (multiple regression on absolute principal component scores) was applied on separate fine and coarse aerosol data for source identification and apportionment. Results demonstrated that the largest contribution to fine-sized aerosol is traffic (38%) followed by road dust (28%), while road dust clearly dominated the coarse size fraction (57%).     

Evolution of vehicle exhaust particles in the atmosphere

Aerosol mass spectrometer (AMS) measurements are used to characterize the evolution of exhaust particulate matter (PM) properties near and downwind of vehicle sources. The AMS provides time-resolved chemically speciated mass loadings and mass-weighted size distributions of nonrefractory PM smaller than 1 microm (NRPM1). Source measurements of aircraft PM show that black carbon particles inhibit nucleation by serving as condensation sinks for the volatile and semi-volatile exhaust gases. Real-world source measurements of ground vehicle PM are obtained by deploying an AMS aboard a mobile laboratory. Characteristic features of the exhaust PM chemical composition and size distribution are discussed. PM mass and number concentrations are used with above-background gas-phase carbon dioxide (CO2) concentrations to calculate on-road emission factors for individual vehicles. Highly variable ratios between particle number and mass concentrations are observed for individual vehicles. NRPM1 mass emission factors measured for on-road diesel vehicles are approximately 50% lower than those from dynamometer studies. Factor analysis of AMS data (FA-AMS) is applied for the first time to map variations in exhaust PM mass downwind of a highway. In this study, above-background vehicle PM concentrations are highest close to the highway and decrease by a factor of 2 by 200 m away from the highway. Comparison with the gas-phase CO2 concentrations indicates that these vehicle PM mass gradients are largely driven by dilution. Secondary aerosol species do not show a similar gradient in absolute mass concentrations; thus, their relative contribution to total ambient PM mass concentrations increases as a function of distance from the highway. FA-AMS of single particle and ensemble data at an urban receptor site shows that condensation of these secondary aerosol species onto vehicle exhaust particles results in spatial and temporal evolution of the size and composition of vehicle exhaust PM on urban and regional scales.     

Estimation of actinic flux and photolysis rate constant of NO2 from aerosol size data

Aerosol mass measurements made using Andersen cascade impactor at different locations in an urban area were used to study the variation in power-law exponent in the Junge-type number distribution. The discrete mass size data were inverted by modified Twomey algorithm to obtain continuous mass size distribution from which number distributions were derived. These were used for evaluating actinic fluxes and hence NO₂ photolysis rate constants employing a radiative transfer model with delta-Eddington approximation.Results of the spatial variation of Junge power-law exponent over the urban region are presented. The relative magnitude of photolysis rate constants over regions with differing aerosol emission characteristics are illustrated. Parametric studies indicated the importance of considering fractional elemental carbon content of the aerosols in the atmosphere. Results of a limited validation study of the model are also presented using quartz crystal microbalance impactor data at one of the sites.     

Dynamic Calibration of an Acid Aerosol Analyzer

A method is described for dynamic calibration of an acid aerosol analyzer based on a commercial modification of the Thomas Autometer and manufactured by the Instrument Development Company. This automated instrument removes acid aerosol from an air stream by sonic impaction, and the sulfuric acid collected is determined conductometrically. An all-glass aerosol generator based on the reaction of water vapor with sulfur trioxide vapor released from fuming sulfuric acid was built for the calibration. Air samples were withdrawn for instrument calibration before and after the concentration of the acid aerosol was determined by titration. The apparent particle size as determined by an Andersen sampler ranged from 2.0 microns to less than 0.68 micron and exhibited a sharp peak with mass median diameter at 1.3 microns in the distribution curve. The size of the aerosol, within certain limits, could be controlled by humidity. Data indicated a linear response with an aerosol collection efficiency of 80 percent in the important respirable size range.     

An integrated approach to identify the origin of PM10 exceedances

Purpose

This study was aimed to the development of an integrated approach for the characterization of particulate matter (PM) pollution events in the South of Italy.

Methods

PM₁₀ and PM_2.5 daily samples were collected from June to November 2008 at an urban background site located in Bari (Puglia Region, South of Italy). Meteorological data, particle size distributions and atmospheric dispersion conditions were also monitored in order to provide information concerning the different features of PM sources.

Results

The collected data allowed suggesting four indicators to characterize different PM₁₀ exceedances. PM_2.5/PM₁₀ ratio, natural radioactivity, aerosol maps and back-trajectory analysis and particle distributions were considered in order to evaluate the contribution of local anthropogenic sources and to determine the different origins of intrusive air mass coming from long-range transport, such as African dust outbreaks and aerosol particles from Central and Eastern Europe. The obtained results were confirmed by applying principal component analysis to the number particle concentration dataset and by the chemical characterization of the samples (PM₁₀ and PM_2.5).

Conclusions

The integrated approach for PM study suggested in this paper can be useful to support the air quality managers for the development of cost-effective control strategies and the application of more suitable risk management approaches.     

On the relation between the size and chemical composition of aerosol particles and their optical properties

The light scattering and absorption coefficients of fine atmospheric aerosol particles were recorded in Hungary under rural conditions in 1998–1999 by an integrating nephelometer and particle soot absorption photometer, respectively. In some cases optical properties in the fine size range were compared to those in the coarse particles. Results obtained indicate, as expected, that fine particles control the scattering and absorption caused by the aerosol. In 1999 the size distribution of aerosol particles was also monitored by means of an electric low pressure impactor (ELPI). This makes it possible the study of the relationship between the number, surface and mass concentration in the size range of 0.1–1.0 μm and the optical characteristics by also considering the chemical composition of the particles.     

A Portable Electrical Analyzer for Size Distribution Measurement of Submicron Aerosols

An electrical aerosol analyzer capable of performing rapid, in situ size distribution measurement on aerosols from 0.003 to 1 μm diameter has been described. The instrument is based on the “diffusion charging-mobility analysis” principle first described by Whitby and Clark. The prototype instrument has a total volume of 3.75 ft³ and a total weight of 60 lb, and is sufficiently portable to be used on small airplanes and ground based vehicles for mobile air pollution studies. The paper describes the design, operation, and performance of the instrument. Sample data are presented showing the size distributions of aerosols measured by the instrument on board a small research aircraft over the Los Angeles basin at several different altitudes. In addition, data are presented showing the size distribution of smog chamber aerosols and aerosols produced by a conventional Collison atomizer.     

Shortwave radiative forcing efficiency of urban aerosols--a case study using ground based measurements

Aerosols reduce the surface reaching solar flux by scattering the incoming solar radiation out to space. Various model studies on climate change suggest that surface cooling induced by aerosol scattering is the largest source of uncertainty in predicting the future climate. In the present study measurements of aerosol optical depth (AOD) and its direct radiative forcing efficiency has been presented over a typical tropical urban environment namely Hyderabad during December, 2003. Measurements of AOD have been carried out using MICROTOPS-II sunphotometer, black carbon aerosol mass concentration using Aethalometer, total aerosol mass concentration using channel Quartz Crystal Microbalance (QCM) Impactor Particle analyser and direct normal solar irradiance using Multifilter Rotating Shadow Band Radiometer (MFRSR). Diurnal variation of AOD showed high values during afternoon hours. The fraction of BC estimated to be approximately 9% in the total aerosol mass concentration over the study area. Results of the study suggest -62.5 Wm(-2) reduction in the ground reaching shortwave flux for every 0.1 increase in aerosol optical depth. The results have been discussed in the paper.     

Monitoring of sources and atmospheric processes controlling air quality in an urban Mediterranean environment

Different monitoring parameters (PM mass concentrations, number–size distribution, black carbon, gaseous pollutants, and chemical composition, among others) are currently used in air quality studies. Urban aerosols are the result of several sources and atmospheric processes, which suggests that a single monitoring technique is insufficient to quantitatively evaluate all of them.This study assesses the suitability of a number of monitoring techniques (PM mass concentrations, number and size distribution of ultra-fine particles, levels of gaseous pollutants, and a complete chemical characterization of PM₁₀ and PM_2.5) by examining the response of those techniques to the different emission sources and/or atmospheric processes affecting an urban Mediterranean area (Barcelona, NE Spain).The results of this work reveal that the PM mass, the number concentration and the chemical composition give different, but complementary, information. Whereas the mineral matter, a key atmospheric aerosol component across the Mediterranean, is not properly quantitatively assessed by measuring sub-micrometric particles, the monitoring of the number concentration is indispensable to interpret the origin of specific aerosol episodes. Furthermore, the chemical composition yields very relevant information to deduce the causes of specific pollution episodes.The number concentration of ultra-fine particles in urban areas is strongly dependent upon vehicle exhaust emissions, which may cause adverse health impacts. Moreover, urban Mediterranean environments are favourable to produce nucleation-mode particles (<20 nm) with photochemical origin. In those cases, these particles are expected to be of high solubility and consequently their toxicity may differ from that of traffic-generated ultra-fine particles. Thus, the use of a single monitoring parameter to evaluate the health effects seems to be not enough.