Historical and future emission of hazardous air pollutants (HAPs) from gas-fired combustion in Beijing,China

Environmental Science and Pollution Research - The consumption of natural gas in Beijing has increased in the past decade due to energy structure adjustments and air pollution abatement. In this...     

Asbestos: Rationale Behind A Proposed Air Quality Standard

A computerized simulation model has been developed to compute energy requirements of a limestone slurry flue gas desulfurization (FGD) system as a function of FGD system design parameters, power plant characteristics, coal properties, and sulfur dioxide emission regulation. Results are illustrated for a "base case" plant of 500 MW, burning 3.5% sulfur coal, meeting the federal new source performance standard of 1.2 lb SO₂/10⁶ Btu. The flue gas is cleaned by an electrostatic precipitator followed by a limestone FGD system with a TCA scrubbing vessel and an optimized in-line steam reheater. The total FGD system energy requirement for this case was found to be 3.4% of the total energy input to the boiler. Sensitivity analyses were then performed in which the nominal values of ten system parameters were individually varied. This caused the total FGD system energy requirement to vary between 2.5 % and 6.1 % of the gross plant output for the range of parameters tested. The most sensitive parameters were found to be scrubbing slurry pH, which affects pumping requirements, and stack gas exit temperature, which affects reheat requirements. In all cases, FGD energy requirements were minimized when the SO₂ emission standard was met by partially bypassing the scrubber. In light of the recent Clean Air Act Amendments this option may not be feasible in the future.     

Energy consumption and energy-saving potential analysis of pollutant abatement systems in a 1000-MW coal-fired power plant

Pollutant abatement systems are widely applied in the coal-fired power sector, and the energy consumption is considered an important part of the auxiliary power. An energy consumption analysis and assessment model of pollutant abatement systems in a power unit was developed based on the dynamic parameters and technology. The energy consumption of pollutant abatement systems in a 1000-MW coal-fired power unit that meets the ultra-low emission limits and the factors of operating parameters, including unit load and inlet concentration of pollutants, on the operating power were analyzed. The results show that the total power consumption of the pollutant abatement systems accounted for 1.27% of the gross power generation during the monitoring period. The wet flue gas desulfurization (WFGD) system consumed 67% of the rate, whereas the selective catalytic reduction (SCR) and electrostatic precipitator (ESP) systems consumed 8.9% and 24.1%, respectively. The power consumption rate of pollutant abatement systems decreased with the increase of unit load and increased with the increase of the inlet concentration of pollutants. The operation adjustment was also an effective method to increase the energy efficiency. For example, the operation adjustment of slurry circulation pumps could promote the energy-saving operation of the WFGD system.

Implications: The application of pollutant abatement technologies increases the internal energy consumption of the power plant, which will lead to an increase of power generation costs. The real-time energy consumption of the different pollutant abatement systems in a typical power unit is analyzed based on the dynamic operating data. Further, the influence of different operating parameters on the operating power of the system and the possible energy-saving potential are analyzed.     

Air pollution reduction via use of green energy sources for electricity and hydrogen production

The implementation of renewable wind and solar energy sources instead of fossil fuels to produce such energy carriers as electricity and hydrogen facilitates reductions in air pollution emissions. Unlike from traditional fossil fuel technologies, air pollution emissions from renewable technologies are associated mainly with the construction of facilities. With present costs of wind and solar electricity, it is shown that, when electricity from renewable sources replaces electricity from natural gas, the cost of air pollution emission abatement is more than ten times less than the cost if hydrogen from renewable sources replaces hydrogen produced from natural gas. When renewable-based hydrogen is used instead of gasoline in a fuel cell vehicle, the cost of air pollution emissions reduction approaches the same value as for renewable-based electricity only if the fuel cell vehicle efficiency exceeds significantly (i.e., by about two times) that of an internal combustion vehicle. The results provide the basis for a useful approach to an optimal strategy for air pollution mitigation.     

F-T合成技术生产替代燃料对环境的影响及对策

主要介绍了F-T合成柴油的特性,阐述了其作为清洁能源的优越性;利用生命周期清单分析方法,比较了以煤、生物质及天然气为原料采用F-T合成技术生产替代能源的工艺路线前提下,在提取生产、转化精炼、运输分配、最终用途燃烧、全部燃料链各阶段温室气体排放情况,提出了温室气体的减排对策。     

Fossil fuels in the 21st century

An overview of the importance of fossil fuels in supplying the energy requirements of the 21st century, their future supply, and the impact of their use on global climate is presented. Current and potential alternative energy sources are considered. It is concluded that even with substantial increases in energy derived from other sources, fossil fuels will remain a major energy source for much of the 21st century and the sequestration of CO2 will be an increasingly important requirement.     

Energy Consumption Requirements for Air Pollution Control Equipment at An Iron Foundry

Energy consumption requirements for air pollution control equipment were studied for varying removal efficiency levels at the Tyler Pipe Industries iron foundry in Tyler, Texas, based on plant fuel consumption data, and on field test measurements of cupola carbon monoxide and particulate control equipment. Natural gas consumption for CO removal increased from 0 in 1970 to 25.4% of the plant total in 1976. Operating costs to achieve 85% CO control increased from 0 in 1970 to $1.61/ton metal in 1976. Increasing cupola incinerator temperature from 800° to 1600° F increased CO removal efficiency from 60 to 97%, but also increased natural gas consumption by 150%. Electricity consumption requirements for 95% to 97% particulate control at the foundry increased from 0.1 % of plant total in 1970 to 18.7% in 1976. Electricity consumption for particulate controls increased plant operating costs from 0.004 in 1970 to 1.693 $/ton metal in 1976 as horsepower increased from 20 to 6,272. Cost-benefit methodology is needed to evaluate trade-offs between air pollution control, energy consumption requirements and operating costs of proposed regulations. Total air pollution control system must be considered in enforcing regulations instead of the source to be controlled alone for overall impacts. Need exists for process modifications to enhance energy recovery and development of energy-effective air pollution control equipment.     

Abatement of sulfur hexafluoride emissions from the semiconductor manufacturing process by atmospheric-pressure plasmas

Sulfur hexafluoride (SF6) is an important gas for plasma etching processes in the semiconductor industry. SF6 intensely absorbs infrared radiation and, consequently, aggravates global warming. This study investigates SF6 abatement by nonthermal plasma technologies under atmospheric pressure. Two kinds of nonthermal plasma processes--dielectric barrier discharge (DBD) and combined plasma catalysis (CPC)--were employed and evaluated. Experimental results indicated that as much as 91% of SF6 was removed with DBDs at 20 kV of applied voltage and 150 Hz of discharge frequency for the gas stream containing 300 ppm SF6, 12% oxygen (O2), and 40% argon (Ar), with nitrogen (N2) as the carrier gas. Four additives, including Ar, O2, ethylene (C2H4), and H2O(g), are effective in enhancing SF6 abatement in the range of conditions studied. DBD achieves a higher SF6 removal efficiency than does CPC at the same operation condition. But CPC achieves a higher electrical energy utilization compared with DBD. However, poisoning of catalysts by sulfur (S)-containing species needs further investigation. SF6 is mainly converted to SOF2, SO2F4, sulfur dioxide (SO2), oxygen difluoride (OF2), and fluoride (F2). They do not cause global warming and can be captured by either wet scrubbing or adsorption. This study indicates that DBD and CPC are feasible control technologies for reducing SF6 emissions.     

天然气引射调峰系统的噪声形成及其治理研究

采用天然气引射调峰技术，能使上海某储配站10台天然气高压球罐的储气调峰能率提高68％，大大有助于解决天然气用气高峰时的供需平衡问题，并能节约初投资人民币1亿元。但使用超音速引射器后，当球罐压力下降到某一值时会产生高频噪声，影响管束区操作环境。本文分析了噪声产生的原因．提出了合理的噪声治理方案，并进行了方案的实施。实践证明：噪声治理效果良好，降低了管束区噪声污染，达到了国家“工业企业噪声卫生标准”。     

天然气引射调峰系统的噪声形成及其治理研究

采用天然气引射调峰技术,能使上海某储配站10台天然气高压球罐的储气调峰能率提高68%,大大有助于解决天然气用气高峰时的供需平衡问题,并能节约初投资人民币1亿元.但使用超音速引射器后,当球罐压力下降到某一值时会产生高频噪声,影响管束区操作环境.本文分析了噪声产生的原因,提出了合理的噪声治理方案,并进行了方案的实施.实践证明:噪声治理效果良好,降低了管束区噪声污染,达到了国家"工业企业噪声卫生标准".     

Potential of conservation agriculture modules for energy conservation and sustainability of rice-based production systems of Indo-Gangetic Plain region

Rice-based cropping systems are the most energy-intensive production systems in South Asia. Sustainability of the rice-based cropping systems is nowadays questioned with declining natural resource base, soil degradation, environmental pollution, and declining factor productivity. As a consequence, the search for energy and resource conservation agro-techniques is increasing for sustainable and cleaner production. Conservation agriculture (CA) practices have been recommended for resource conservation, soil health restoration and sustaining crop productivity. The present study aimed to assess the different CA modules in rice-based cropping systems for energy conservation, energy productivity, and to define energy-economic relations. A field experiment consisted of four different tillage-based crop establishment practices (puddled-transplanted rice followed by (fb) conventional-till maize/wheat (CTTPR-CT), non-puddled transplanted rice fb zero-till maize/wheat (NPTPR-ZT), zero-till transplanted rice fb zero-till maize/wheat (ZTTPR-ZT), zero-till direct-seeded rice fb zero-till maize/wheat (ZTDSR-ZT)), with two residue management treatments (residue removal, residue retention) in rice–wheat and rice–maize rotations were evaluated for energy budgeting and energy-economic relations. Conservation-tillage treatments (NPTPR-ZT, ZTTPR-ZT, and ZTDSR-ZT) reduced the energy requirements over conventional tillage treatments, with the greater reduction in ZTTPR-ZT and ZTDSR-ZT treatments. Savings of energy in conservation-tillage treatments were attributed to reduced energy use in land preparation (69–100%) and irrigation (23–27%), which consumed a large amount of fuel energy. Conservation-tillage treatments increased grain and straw/stover yields of crops, eventually increased the output energy (6–16%), net energy (14–26%), energy ratio (25–33%), and energy productivity (23–34%) as compared with CTTPR-CT. For these energy parameters, the treatment order was ZTDSR-ZT ≥ ZTTPR-ZT > NPTPR-ZT > CTTPR-CT (p < 0.05). Crop residue retention reduced net energy, energy ratio, and energy productivity when compared with residue removal. Our results of energy-economic relations favored the “conservative hypothesis,” which envisages that energy and monetary investments are not essentially the determinants of crop productivity. Thus, zero tillage-based crop establishments (ZTTPR-ZT, ZTDSR-ZT) in rice-based production systems could be the sustainable alternative to conventional tillage-based agriculture (CTTPR-CT) as they conserved non-renewable energy sources, reduced water requirement, and increased crop productivity.

     

Impact of the implementation of PM abatement technology on the ambient air levels of metals in a highly industrialised area

Data on the spatial and time (2002–2005) variation of levels of trace elements and the source attribution of these elements in the ceramic cluster of Castelló (Eastern Spain) are presented and discussed. Earlier studies concluded that metal levels in PM₁₀ were one of the most critical parameters for attaining the EU legal requirements of the air quality standards. Levels of Li, Sc, Co, Zn, As, Se, Rb, Zr, Cd, Cs, Ce, Tl and Pb were higher than the usual range of concentration in urban areas of Spain, and some of them exceeded the concentration ranges obtained for other industrial sites in Spain. Of these elements, Zr, Zn, Pb and As (and probably Tl) may be considered as tracers of the ceramic emissions from the study area. A downward trend was observed for most of them, simultaneously, with the progressive implementation of the emission abatement techniques, especially those applied to the PM abatement of the manufacture of glaze components and the avoidance of the use of specific raw materials with high contents of impurities. At the end of the study period, the elements for which the EU sets limit or target values met the established requirements for 2013 (2005 for Pb), whereas, at the beginning of the study some elements exceeded the 2013 target values. Furthermore, a detailed discussion on the interpretation of peak concentration events and source attribution for a number of trace elements is presented. Five different sources were identified: mineral emissions (from clay use and handling), industry (mainly glaze production and use), road traffic, sea spray and the regional background influenced by a fuel oil-power plant and a petrochemical plant.     

新型烟气冷凝节能与脱硫装置研究

烟气冷凝节能与脱硫装置是适用于燃油燃气锅炉的新装置。本文介绍了该装置节能及脱硫的基本原理,利用81.4KW天然气锅炉实验系统对装置的传热和脱硫特性进行了研究。实验表明,该装置提高锅炉效率为3％-8％,脱硫效率为20％-40％。     

Closing the carbon cycle through rational use of carbon-based fuels

In this paper, a brief overview is presented of natural gas as a fuel resource with subsequent carbon capture and re-use as a means to facilitate reduction and eventual elimination of man-made carbon emissions. A particular focus is shale gas and, to a lesser extent, methane hydrates, with the former believed to provide the most reasonable alternative as a transitional fuel toward a low-carbon future. An emphasis is placed on the gradual elimination of fossil resource usage as a fuel over the coming 35 to 85 years and its eventual replacement with renewable resources and nuclear power. Furthermore, it is proposed that synthesis of chemical feedstocks from recycled carbon dioxide and hydrogen-rich materials should be undertaken for specific applications in the transport sector which require access to high energy density fuels. To achieve the latter, carbon dioxide capture is imperative and possible synthetic routes for chemical feedstock production are briefly reviewed.     

Mobile measurement of methane and hydrogen sulfide at natural gas production site fence lines in the Texas Barnett Shale

Production of natural gas from shale formations is bringing drilling and production operations to regions of the United States that have seen little or no similar activity in the past, which has generated considerable interest in potential environmental impacts. This study focused on the Barnett Shale Fort Worth Basin in Texas, which saw the number of gas-producing wells grow from 726 in 2001 to 15,870 in 2011. This study aimed to measure fence line concentrations of methane and hydrogen sulfide at natural gas production sites (wells, liquid storage tanks, and associated equipment) in the four core counties of the Barnett Shale (Denton, Johnson, Tarrant, and Wise). A mobile measurement survey was conducted in the vicinity of 4788 wells near 401 lease sites, representing 35% of gas production volume, 31% of wells, and 38% of condensate production volume in the four-county core area. Methane and hydrogen sulfide concentrations were measured using a Picarro G2204 cavity ring-down spectrometer (CRDS). Since the research team did not have access to lease site interiors, measurements were made by driving on roads on the exterior of the lease sites. Over 150 hr of data were collected from March to July 2012. During two sets of drive-by measurements, it was found that 66 sites (16.5%) had methane concentrations >3 parts per million (ppm) just beyond the fence line. Thirty-two lease sites (8.0%) had hydrogen sulfide concentrations >4.7 parts per billion (ppb) (odor recognition threshold) just beyond the fence line. Measured concentrations generally did not correlate well with site characteristics (natural gas production volume, number of wells, or condensate production). t tests showed that for two counties, methane concentrations for dry sites were higher than those for wet sites. Follow-up study is recommended to provide more information at sites identified with high levels of methane and hydrogen sulfide.

Implications:Information regarding air emissions from shale gas production is important given the recent increase in number of wells in various regions in the United States. Methane, the primary natural gas constituent, is a greenhouse gas; hydrogen sulfide, which can be present in gas condensate, is an odor-causing compound. This study surveyed wells representing one-third of the natural gas production volume in the Texas Barnett Shale and identified the percent of sites that warrant further study due to their fence line methane and hydrogen sulfide concentrations.     

State of energy consumption and CO2 emission in Bangladesh

Carbon dioxide (CO2) is one of the most important gases in the atmosphere, and is necessary for sustaining life on Earth. It is also considered to be a major greenhouse gas contributing to global warming and climate change. In this article, energy consumption in Bangladesh is analyzed and estimates are made of CO2 emission from combustion of fossil fuel (coal, gas, petroleum products) for the period 1977 to 1995. International Panel for Climate Change guidelines for national greenhouse gas inventories were used in estimating CO2 emission. An analysis of energy data shows that the consumption of fossil fuels in Bangladesh is growing by more than 5% per year. The proportion of natural gas in total energy consumption is increasing, while that of petroleum products and coal is decreasing. The estimated total CO2 release from all primary fossil fuels used in Bangladesh amounted to 5072 Gigagram (Gg) in 1977, and 14 423 Gg in 1995. The total amounts of CO2 released from petroleum products, natural gas, and coal in the period 1977-1995 were 83 026 Gg (50% of CO2 emission), 72 541 Gg (44% of CO2 emission), and 9545 Gg (6% CO2 emission), respectively. A trend in CO2 emission with projections to 2070 is generated. In 2070, total estimated CO2 emission will be 293 260 Gg with a current growth rate of 6.34% y . CO2 emission from fossil fuels is increasing. Petroleum products contribute the majority of CO2 emission load, and although the use of natural gas is increasing rapidly, its contribution to CO2 emission is less than that of petroleum products. The use of coal as well as CO2 emission from coal is expected to gradually decrease.     

The role of coal technologies to support responsible economic growth

The Asian Pacific region is home to the fastest-growing economies in the world. These economies are expected to double gross domestic product (GDP) in the next decade, and coal will play a major role as the primary energy source for electric power. The tremendous projected financial burden associated with the installation of new, coal-fired electric power facilities to fuel this unprecedented economic growth has focused efforts to identify existing and new sources of financing for major thermal power projects that are efficient and environmentally responsible. The economics are trying to accelerate economic development and promote the leveraging of in-country resources to meet their electric power objectives. With the growth in power production will come more greenhouse gas emissions and negative environmental impacts. The means to reducing these impacts is clean coal technology, which is becoming more and more accepted for debt financing. Competition for debt financing is becoming tighter worldwide, with increased use of project financing. Representatives of the coal technology and equipment industries believe that the availability of non-recourse financing is an impediment to greater penetration of clean coal technology into electric power markets in Asian Pacific economies. Better use of existing infrastructure project financing instruments and management of risk in Asian markets are critical to the development and acceptance of clean coal technology to meet greenhouse gas abatement and economic goals.     

Evaluation of rational sulphur dioxide abatement in China

Sulphur dioxide (SO₂) abatement is attracting wide attention, with its generation increasing rapidly in China. In this paper, we calculate the SO₂ rational abatement ratio (SRAR) of 30 regions in China from 1990 to 2005, by applying Data Envelopment Analysis (DEA) based on the regional own production frontier. Results show that, the more developed area is, the lower SRAR is. The eastern, central and western areas have the lowest, medium and highest 1990-2005 average SRAR (22.17%, 46.99% and 58.28%), respectively. Chinese government should emphasise particularly on SO2 abatement in central and western area. More investment in SO2 management, introducing advanced technology as well as popularising clean coal technology are the urgent tasks for central and western area to improve SO2 emission efficiency.     

Hydrogen sulfide gas treatment by a chemical-biological process: chemical absorption and biological oxidation steps

In order to remove high concentrations of hydrogen sulfide (H2S) gas from anaerobic wastewater treatments in livestock farming, a novel process was evaluated for H2S gas abatement involving the combination of chemical absorption and biological oxidation processes. In this study, the extensive experiments evaluating the removal efficiency, capacity, and removal characteristics of H2S gas by the chemical absorption reactor were conducted in a continuous operation. In addition, the effects of initial Fe2+ concentrations, pH, and glucose concentrations on Fe2+ oxidation by Thiobacillus ferrooxidans CP9 were also examined. The results showed that the chemical process exhibited high removal efficiencies with H2S concentrations up to 300 ppm, and nearly no acclimation time was required. The limitation of mass-transfer was verified as the rate-determining step in the chemical reaction through model validation. The Fe2+ production rate was clearly affected by the inlet gas concentration as well as flow rate and a prediction equation of ferrous production was established. The optimal operating conditions for the biological oxidation process were below pH 2.3 and 35 degrees C in which more than 90% Fe3+ formation ratio was achieved. Interestingly, the optimal glucose concentration in the medium was 0.1%, which favored Fe2+ oxidation and the growth of T. ferrooxidans CP9.     

Measurements show that marginal wells are a disproportionate source of methane relative to production

ABSTRACT

Oil and natural gas wells are a prominent source of the greenhouse gas methane (CH₄), but most measurements are from newer, high producing wells. There are nearly 700,000 marginal “stripper” wells in the US, which produce less than 15 barrels of oil equivalent (BOE) d^?1. We made direct measurements of CH₄ and volatile organic carbon (VOC) emissions from marginal oil and gas wells in the Appalachian Basin of southeastern Ohio, all producing < 1 BOE d^?1. Methane and VOC emissions followed a skewed distribution, with many wells having zero or low emissions and a few wells responsible for the majority of emissions. The average CH₄ emission rate from marginal wells was 128 g h^?1 (median: 18 g h^?1; range: 0– 907 g h^?1). Follow-up measurements at five wells indicated high emissions were not episodic. Some wells were emitting all or more of the reported gas produced at each well, or venting gas from wells with no reported gas production. Measurements were made from wellheads only, not tanks, so our estimates may be conservative. Stochastic processes such as maintenance may be the main driver of emissions. Marginal wells are a disproportionate source of CH₄ and VOCs relative to oil and gas production. We estimate that oil and gas wells in this lowest production category emit approximately 11% of total annual CH₄ from oil and gas production in the EPA greenhouse gas inventory, although they produce about 0.2% of oil and 0.4% of gas in the US per year.

Implications: Low producing marginal wells are the most abundant type of oil and gas well in the United States, and a surprising number of them are venting all or more of their reported produced gas to the atmosphere. This makes marginal wells a disproportionate greenhouse gas emissions source compared to their energy return, and a good target for environmental mitigation.