Dynamic Calibration of an Acid Aerosol Analyzer

A method is described for dynamic calibration of an acid aerosol analyzer based on a commercial modification of the Thomas Autometer and manufactured by the Instrument Development Company. This automated instrument removes acid aerosol from an air stream by sonic impaction, and the sulfuric acid collected is determined conductometrically. An all-glass aerosol generator based on the reaction of water vapor with sulfur trioxide vapor released from fuming sulfuric acid was built for the calibration. Air samples were withdrawn for instrument calibration before and after the concentration of the acid aerosol was determined by titration. The apparent particle size as determined by an Andersen sampler ranged from 2.0 microns to less than 0.68 micron and exhibited a sharp peak with mass median diameter at 1.3 microns in the distribution curve. The size of the aerosol, within certain limits, could be controlled by humidity. Data indicated a linear response with an aerosol collection efficiency of 80 percent in the important respirable size range.     

Measurements of Sulfur Oxides,Nitrogen Oxides,Haze and Fine Particles at a Rural Site on the Atlantic Coast

During August, 1982 and January and February, 1983, General Motors Research Laboratories operated air monitoring sites on the Atlantic Coast near Lewes, Delaware and 1250 km to the east on the southwest coast of Bermuda. The overall purpose of this project was to study the transformations of the principal acid precipitation precursors, NO _x and SO _x species, as they transport under conditions not complicated by emissions from local sources. In this paper, the measurements of gas and particulate species from Lewes are described and the composition and sources of sulfate aerosol, which is the most important haze-producing species, are investigated.

On the average, the total suspended particulate (TSP) concentration was 27.9 μg/m³ while the PM₁₀ (mass of particles with a diameter less than or equal to 10 μm) concentration was 22.0 μg/m³ or 79 percent of the TSP. The PM₁₀ consisted of 6.1 μg/m³ of coarse particles (CPM, diameter = 2.5 ? 10μm) and 15.9 μg/m³ of fine particles (FPM, diameter < 2.5 μm).

On a mass basis the most important constituents of the fine particulate fraction were sulfate compounds, 50 percent, and organic compounds, 30 percent. The mean light extinction coefficient corresponds to a visual range of 18-20 km. Most of the extinction can be attributed to the sulfate (60 percent) and organic carbon (13 percent). Particle size measurements show that the mass median aerodynamic diameter for both species is 0.43 μm. This is a typical size for a hydrated sulfate aerosol. For carbon, however, this is a larger size than previously reported and results in a more efficient light scattering aerosol. Principal component analyses indicate that coal combustion emissions from the midwestern U.S. are the most significant source of sulfate in Lewes during the summer and winter.     

Characteristics of Individual Particles at a Rural Site in the Eastern United States

To determine the nature of aerosol particles in a rural area of the eastern United States, aerosol samples were collected at Deep Creek Lake, Maryland, on various substrates and analyzed by a scanning electron microscope (SEM) and a transmission electron microscope (TEM). SEM analysis of particles larger than 2.5 μm collected on Nuclepore filters revealed the following: clay minerals, quartz, gypsum, and calcite comprised 50 percent of the particles analyzed; spores, pollen, and plant debris comprised 25 percent; 9 percent were fly ash; 11 percent were sulfates; 5 percent were unidentified. Particles ranging from 0.3 to 2 μm were collected in a cascade impactor on grid-supported carbon films and analyzed by TEM for decomposition rate as well as for reaction with the barium chloride and nitron (C₂₀H₁₆N₄) films that were applied after sampling. The TEM analyses indicated that as much as 95 percent of the particles in the 0.3- to 2-μm diameter range were pure ammonium sulfate or acidic ammonium sulfate; they contained essentially no insoluble or nonvolatile matter. About 5 percent of the particles were fly ash spheres. When replicas of particles collected on Nucleopore filters were analyzed by TEM, we observed agglomerates of particles smaller than 0.1 μm.     

Comparison of black carbon (BC) aerosols in two urban areas – concentrations and size distributions

In this study, the BC aerosol measured at two very different urban sites is compared in terms of concentration, seasonal variation, and size distribution. During a 14 month study, one impactor sample was performed each month on a day with typical meteorological conditions. One (Vienna) or three (Uji) filter samples were obtained during the sampling time of the impactors. BC concentration in both the filter and impactor samples was analyzed with an optical technique (integrating sphere technique), where a calibration curve obtained from commercial carbon black is used to convert the optical signal to BC mass. Gravimetric mass concentration was measured at both sites. The gravimetric mass size distribution was measured only in Vienna. At both sites, the yearly average of the BC concentration on the sampling days was around 5 μg m⁻³. In Vienna, some seasonal trend with high concentrations during the cold season was observed, while in Uji, no pronounced seasonal trend was found. The BC size distribution in Uji was distinctly bimodal in the submicron size range. Log-normal distributions were fitted through the impactor data. The average BC mass median diameters (MMD) of the two submicron modes were 0.15 and 0.39 μm. Each mode contained about the same amount of BC mass. In Vienna only one submicron BC mode (average MMD 0.3 μm) was found because of the low size resolution of the impactor. An analysis of humidity effects on the MMDs of BC (both sites) and gravimetric mass (Vienna only) indicates that the Vienna aerosol is partly mixed internally with respect to BC, while the Uji aerosol seems to be externally mixed.     

Chemical characteristics of free tropospheric aerosols over the Japan Sea coast: aircraft-borne measurements

Atmospheric aerosol particulate matter was directly collected in the free troposphere over the Japan Sea coast between 1992 and 1994 using an aircraft-borne nine-stage cascade impactor (particle size range: 0.1–8 μm). The water-soluble components in the aerosol particulate matter were analyzed by ion chromatography. Particulate sulfate and ammonium were detected in most of the samples and their size distributions showed noticeable peaks below the 1 μm particle size range. Water-soluble calcium (Ca²⁺) was detected in half of the samples; the size distribution showed that the maximum particle size was larger than 1 μm. Highly concentrated Ca²⁺ in larger particles was possibly due to transport of Kosa aerosols from the Asian continent in the free troposphere. The concentration of fine particulate sulfate and ammonium tended to increase whenever Ca²⁺ was detected, which suggests possible mixing of Kosa aerosols and non-Kosa aerosols during long-range transport of air masses containing Kosa particles.     

Design and Testing of a New Size Classifying Isokinetic Sequential Aerosol Sampler

Two versions of a size-classifying isokinetic sequential aerosol sampler (SCISAS) have been designed, built, tested, and deployed in a field program in the southwestern United States. The SCISAS units can operate at unattended sites, exposing four or more filter types simultaneously, in two size ranges, for six sampling time Intervals. Design considerations included theoretical estimates of aerosol particle losses in the 0-15 μm size range.

SCISAS prototypes have been tested to evaluate their sampling efficiency as a function of flow rate, the sensitivity of the sampling efficiency to isokinetic matching within the SCISAS sampling stack, the equivalency of their sampling ports, and their passive deposition characteristics. The prototypes were also compared to several other types of aerosol filtration samplers already in common use. These tests show that particle loss mechanisms within the SCISAS usually cause no more than 5 percent losses, and that the SCISAS units agree, within one to two measurement uncertainty intervals, with other types of aerosol samplers.     

Performance evaluation of six different aerosol samplers in a particulate matter generation chamber

The present study was carried out with the aim of evaluating the performance of six different aerosol samplers in terms of mass concentration, particle size distribution, and mass fraction for the international size-sampling conventions. The international size-sampling criteria were defined as inhalable, thoracic, and respirable mass fractions with 50% cutoff at an aerodynamic equivalent diameter of 100 μm, 10 μm, and 4 μm, respectively. Two Andersen, four total suspended particulate (TSP), two RespiCon, four PM₁₀, two DustTrak, and two SidePak samplers were selected and tested to quantitatively estimate human exposure in a carefully controlled particulate matter (PM) test chamber. The overall results indicate that (1) Andersen samplers underestimate total suspended PM and overestimate thoracic and respirable PM due to particle bounce and carryover between stages, (2) TSP samplers provide total suspended PM as reference samplers, (3) TSP samplers quantified by a coulter counter multisizer provide no information below an equivalent spherical diameter of 2 μm and therefore underestimate respirable PM, (4) RespiCon samplers are free from particle bounce as inhalable samplers but underestimate total suspended PM, (5) PM₁₀ samplers overestimate thoracic PM, and (6) DustTrak and SidePak samplers provide relative PM concentrations instead of absolute PM concentrations.     

Simultaneous measurement of light-scattering properties and particle size distribution for aerosols: Application to ammonium sulfate and quartz aerosol particles

An apparatus for measuring the scattering phase function and linear polarization of aerosol particles has been developed. The apparatus uses an elliptical mirror and CCD camera to image the full angular scattering range simultaneously. An in-line aerodynamic particle sizer (APS) in the particle flow stream provides for the simultaneous measurement of the aerosol particle size distribution. This apparatus allows for a comparison of measured optical properties with theoretical model calculations based on the measured aerosol size distribution. The system was calibrated and tested using monodisperse polystyrene latex (PSL) spheres and with ammonium sulfate (AS) aerosol. We have also used the apparatus for measuring the scattering phase function and linear polarization for light scattering from irregular quartz aerosol particles. Our results show that Mie theory substantially overestimates the backscattering cross-section for quartz particles in the size parameter range X∼2–4, in agreement with previous experimental work and theoretical modeling studies. We also present a normalized synthetic phase function for quartz dust aerosol in the accumulation mode size range (0.1–2.0 μm).     

Spatial and temporal variations in San Joaquin Valley fog chemistry

Fog was sampled at four locations in California’s San Joaquin Valley (SJV) during December 1995 and January 1996 as part of the 1995 Integrated Monitoring Study (IMS95). The fog sampling campaign was conducted in two phases. During the first phase, fog was sampled at three southern SJV surface locations, two urban (Fresno and Bakersfield) and one rural (near the Kern Wildlife Refuge). Both bulk samples (representative of the entire fog drop spectrum) and size-fractionated samples were collected. During the second phase, bulk fog samples were collected at three elevations on a 430 m television transmission tower in the northern SJV, representing some of the first observations of vertical variations in fog composition. SJV fog was observed to be consistently alkaline. The median pH measured in the southern SJV was 6.49, with a range from 4.97 to 7.43. Dominant species in the fog water were ammonium (median southern SJV concentration of 1008 microequivalents/l (μN)), nitrate (483 μN), sulfate (117 μN), acetate (117 μN), formate (63 μN), and formaldehyde (46 μM). Concentrations of the inorganic ions were similar in the urban and rural fogs, although occasionally much higher spikes of S(IV) and sulfate were observed in Bakersfield fog. Acetate, formaldehyde, and total organic carbon, by contrast, were observed to be present in greater concentration in the urban fogs. Bakersfield IMS95 fog concentrations of most species were similar to those measured there in the early 1980s, although concentrations of S(IV) and sulfate were much lower in IMS95 fogs. Significant differences were found between the composition of large and small fog drops, with pH differences at times exceeding one pH unit. The chemical heterogeneity present among SJV fog drop populations is likely to result in significant enhancement of aqueous sulfate production rates over those expected from average fog properties. Significant vertical variations were also observed in fog composition. Liquid water content was observed to increase strongly with elevation, while major ion aqueous concentrations in fog drops decreased with altitude. The total amount of solute contained within the fog (per unit volume of air) was observed to increase with altitude. These observations form a unique data set to be used for model evaluation and for further analysis of aerosol processing by fogs.     

Atmospheric Aerosol Composition and Concentration as a Function of Particle Size and of Time

As a step toward better understanding the reactive Los Angeles air basin atmosphere, a study was undertaken at the University of California—Riverside Campus, to determine the composition and concentration of atmospheric particulate matter as a function of particle size and time. The study involved developing a method for obtaining size-classified, time-fractionated aerosol samples amenable to chemical and physical (including microscopic) analysis. During a 15-day period, samples were obtained over 4-hr periods and subsequently analyzed for nitrate, sulfate, iron, and lead. Concentration of six gaseous pollutantsj total aerosol light-scattering, and several meteorological measurements were simultaneously recorded and averaged over the 4-hr intervals. This data was presented graphically to show the diurnal variation in and relationship between gaseous, particulate, and meteorological measurements. A strong relationship between gaseous peroxyacetyl nitrate, particulate nitrate, and aerosol light-scattering was found. High concentrations of ammonium nitrate particles, mainly in the 0.5-2μ, diameter size range, were found in the atmospheric particulate samples collected on days of very high smog (very limited visibility).     

Optical and chemical properties of marine boundary-layer aerosol around Japan determined from shipboard measurements in 2002

Shipboard measurements of the optical and chemical properties of marine boundary-layer aerosol were made around Japan over the period from 28 August to 25 September 2002. Measurements were conducted aboard the Research Vessel (R/V) Shirase along cruise tracks beginning from Yokosuka, and proceeding on to Hakodate, Sakata, Sasebo, Naha, Kure, and Yokkaichi. This paper describes the results of optical measurements using an Optical Particle Counter (OPC), an Integrating Nephelometer (IN), and a Particle Soot/Absorption Photometer (PSAP), as well as chemical analyses of water-soluble aerosol particles collected by impactor and filter systems. Coulter Multisizer measurements were used for water-insoluble aerosol particles. The complex refractive index (CRI), scattering and absorption coefficients, and size distribution of aerosols were estimated from combined measurements made using OPC, IN, and PSAP. Contrasting aerosol characteristics were observed during different stages of the cruise. Discussion on these differences focuses mainly on two legs: Leg-1 from Yokosuka to Hakodate and Leg-4 from Sasebo to Naha. Backward trajectory analyses indicate that the air sampled during Leg-1 originated from the Pacific Ocean, whereas the air sampled during Leg-4 originated from the Chinese Continent via the Korean Peninsula. For the first half of Leg-1, the number concentration was low and larger particles were relatively predominant. The real and imaginary parts of the CRI were estimated to be 1.38–1.40 and close to zero, respectively. This estimation is consistent with the results of chemical analyses, which show that the sea salt is rich in aerosols sourced from remote ocean areas. In contrast, small particles were predominant during Leg-4, and the real and imaginary parts of the CRI were estimated to be 1.52–1.59 and approximately −0.002, respectively. These findings are also consistent with chemical analyses that reveal a mixture of mineral dust and sulfate aerosol likely transported from China and Korea. The Coulter Multisizer measurements conducted during Leg-4 reveal abundant water-insoluble particles with a mode radius of 1.35 μm.     

Characterization of Airborne Dust from Two Nonferrous Foundries by Physico-chemical Methods and Multivariate Statistical Analyses

Abstract

Airborne particulate matter was sampled at a copper smelter and at an aluminum casting plant. Size, shape, quantity, and microlocalization of chemical species in the particulates were measured using closed cassettes, cascade impactors, scanning electron microscopy, X-ray diffraction, infrared and atomic absorption spectrophotometries, secondary ion mass spectrometry, and photoelectron spectroscopy. Cluster and principal components analyses were used in interpreting results. Aerosol chemistry varies as a function of size, and composition becomes more complex as the aerosol size drops into the respirable fraction and lower. Surface chemical properties are evidenced where, generally, volatile species are enriched. A few site-specific elements and characteristics were identified. The formation of particulates may often be related to process and practices, yet the actual distribution of species in the air remains an intricate matter.     

Size distributions of nano/micron dicarboxylic acids and inorganic ions in suburban PM episode and non-episodic aerosol

The distribution of nano/micron dicarboxylic acids and inorganic ions in size-segregated suburban aerosol of southern Taiwan was studied for a PM episode and a non-episodic pollution period, revealing for the first time the distribution of these nanoscale particles in suburban aerosols. Inorganic species, especially nitrate, were present in higher concentrations during the PM episode. A combination of gas-to-nuclei conversion of nitrate particles and accumulation of secondary photochemical products originating from traffic-related emissions was likely a crucial cause of the PM episode. Sulfate, ammonium, and oxalic acid were the dominant anion, cation, and dicarboxylic acid, respectively, accounting for a minimum of 49% of the total anion, cation or dicarboxylic acid mass. Peak concentrations of these species occurred at 0.54 μm in the droplet mode during both non-episodic and PM episode periods, indicating an association with cloud-processed particles. On average, sulfate concentration was 16–17 times that of oxalic acid. Oxalic acid was nevertheless the most abundant dicarboxylic acid during both periods, followed by succinic, malonic, maleic, malic and tartaric acid. The mass median aerodynamic diameter (MMAD) of oxalic acid was 0.77 μm with a bi-modal presence at 0.54 μm and 18 nm during non-episodic pollution and an MMAD of 0.67 μm with mono-modal presence at 0.54 μm in PM episode aerosol. The concomitant formation of malonic acid and oxalic acid was attributed to in-cloud processes. During the PM episode in the 5–100 nm nanoscale range, an oxalic acid/sulfate mass ratio of 40.2–82.3% suggested a stronger formation potential for oxalic acid than for sulfate in the nuclei mode. For total cations (TC), total inorganic anions (TIA) and total dicarboxylic acids (TDA), major contributing particles were in the droplet mode, with least in the nuclei mode. The ratio of TDA to TIA in the nuclei mode increased greatly from 8.40% during the non-episodic pollution period to 28.08% during the PM episode, favoring dicarboxylic acid formation in the nuclei mode. The evidence suggests stronger formation strength and contribution potential exists for dicarboxylic acids than for inorganic salts in nanoscale particles, especially in PM episode aerosol.     

High-volume Impactor for Sampling Fine and Coarse Particles

Final design, calibration, and field testing have been completed for a new 1.13 m³/min (40 cfm) High-volume Virtual Impactor (HVVI). Field tests have demonstrated that the new classifier/collector works well as an accessory to the existing PM10 Size Selective Inlet high-volume samplers. The HVVI provides two fractions of PM10 mass, both of which are collected by filtration. The fine fraction (0-2.5 μm aero. dia.) Is collected on the standard 20.3 × 25.4 cm (8- × 10-in) high-volume filter; the coarse fraction (2.5-10 μm aero. dia.) is collected on a 5.1 × 15.2 cm (2- × 6-in) filter. Coarse flow through the receiver tubes is limited to 0.057 m³/min (2 cfm), 5 percent of the total flow.

The operating pressure drop across the HVVI stages Is sufficiently high to make changes In pressure across the collection filters Insignificant. The HVVI filter holder assembly facilitates loading/ unloading samples in the laboratory, thus eliminating damage due to handling filters in the field. Size separation characteristics of the HVVI agree well with those for the 16.7 L/min commercially available dichotomous sampler with the 50 percent effectiveness (cut-point) occurring at 2.5 μm. Applying laboratory-determined particle losses to the typical ambient particle mass size distribution described In Federal Register 49, 40 CFR, Part 53, Table D-3, the HVVI fine fraction total mass loss is less than 0.8 percent for liquid particles and less than 0.1 percent for solid particles; coarse fraction total mass loss is less than 2.5 percent for liquid particles, and less than 0.2 percent for solid particles.     

Composition and mixing state of the urban background aerosol in the Rhein-Main area (Germany)

Size-resolved aerosol particle samples in the size range 0.1–10 μm aerodynamic diameter were collected in the years 2003 and 2004 at an urban background station in Mainz, Germany. Size, morphology, chemical composition and mixing state of more than 5400 individual particles of 7 selected sampling days were analyzed in detail by scanning electron microscopy and energy-dispersive X-ray microanalysis. In addition, transmission electron microscopy, aerosol mass spectrometry and atomic force microscopy were applied to obtain detailed information about the mixing state of the particles. The fine particle fraction (diameter<1 μm) is always dominated by complex secondary aerosol particles (⩾90% by number) independent from air mass origin. These particles are complex internal mixtures of ammonium and sodium sulfates, nitrates, and organic material. Between 20% and 40% of the complex secondary aerosol particles contain soot inclusions. The composition of the coarse particle fraction (>1 μm diameter) is strongly dependant on air mass history with variable abundances of complex secondary aerosol particles, aged sea salt, silicates, silicate mixtures, calcium sulfates, calcium sulfate/carbonate mixtures, calcium nitrate/carbonate mixtures, biological particles, and external soot.The dominance of complex secondary aerosol particles shows that reduction of the precursor gases is a major goal for successful reduction strategies for PM₁₀.     

Size-resolved,real-time measurement of water-insoluble aerosols in metropolitan Atlanta during the summer of 2004

During the month of August 2004, the size-resolved number concentration of water-insoluble aerosols (WIA) from 0.25 to 2.0 μm was measured in real-time in the urban center of Atlanta, GA. Simultaneous measurements were performed for the total aerosol size distribution from 0.1 to 2.0 μm, the elemental and organic carbon mass concentration, the aerosol absorption coefficient, and the aerosol scattering coefficient at a dry (RH=30%) humidity. The mean aerosol number concentration in the size range 0.1–2.0 μm was found to be 360±175 cm⁻³, but this quantity fluctuated significantly on time scales of less than one hour and ranged from 25 to 1400 cm⁻³ during the sample period. The mean WIA concentration (0.25–2.0 μm) was 13±7 cm⁻³ and ranged from 1 to 60 cm⁻³. The average insoluble fraction in the size range 0.25–2.0 μm was found to be 4±2.5% with a range of 0.3–38%. The WIA population was found to follow a consistent diurnal pattern throughout the month with concentration maxima concurring with peaks in vehicular traffic flow. WIA concentration also responded to changes in meteorological conditions such as boundary layer depth and precipitation events. The temporal variability of the absorption coefficient followed an identical pattern to that of WIA and ranged from below the detection limit to 55 Mm⁻¹ with a mean of 8±6 Mm⁻¹. The WIA concentration was highly correlated with both the absorption coefficient and the elemental carbon mass concentration, suggesting that WIA measurements are dominated by fresh emissions of elemental carbon. For both the total aerosol and the WIA size distributions, the maximum number concentration was observed at the smallest sizes; however the WIA size distribution also exhibited a peak at 0.45 μm which was not observed in the total population. Over 60% of the particles greater than 1.0 μm were observed to be insoluble in the water sampling stream used by this instrumentation. Due to the refractive properties of black carbon, it is highly unlikely that these particles could be composed of elemental carbon, suggesting a crustal source for super-micron WIA.     

Secondary organic aerosol formation from the oxidation of aromatic hydrocarbons in the presence of dry submicron ammonium sulfate aerosol

A laboratory study was conducted to examine formation of secondary organic aerosols. A smog chamber system was developed for studying gas–aerosol interactions in a dynamic flow reactor. These experiments were conducted to investigate the fate of gas and aerosol phase compounds generated from hydrocarbon–nitrogen oxide (HC/NO_x) mixtures irradiated in the presence of fine (<2.5 μm) particulate matter. The goal was to determine to what extent photochemical oxidation products of aromatic hydrocarbons contribute to secondary organic aerosol formation through uptake on pre-existing inorganic aerosols in the absence of liquid water films. Irradiations were conducted with toluene, p-xylene, and 1,3,5-trimethylbenzene in the presence of NO_x and ammonium sulfate aerosol, with propylene added to enhance the production of radicals in the system. The secondary organic aerosol yields were determined by dividing the mass concentration of organic fraction of the aerosol collected on quartz filters by the mass concentration of the aromatic hydrocarbon removed by reaction. The mass concentration of the organic fraction was obtained by multiplying the measured organic carbon concentration by 2.0, a correction factor that takes into account the presence of hydrogen, nitrogen, and oxygen atoms in the organic species. The mass concentrations of ammonium, nitrate, and sulfate concentrations as well as the total mass of the aerosols were measured. A reasonable mass balance was found for each of the aerosols. The largest secondary organic aerosol yield of 1.59±0.40% was found for toluene at an organic aerosol concentration of 8.2 μm⁻³, followed by 1.09±0.27% for p-xylene at 6.4 μg m⁻³, and 0.41±0.10% for 1,3,5-trimethylbenzene at 2.0 μg m⁻³. In general, these results agree with those reported by Odum et al. and appear to be consistent with the gas–aerosol partitioning theory developed by Pankow. The presence of organic in the aerosol did not affect significantly the hygroscopic properties of the aerosol.     

Aerosol radiative forcing for Asian continental outflow

Asian aerosols in elevated layers over the Pacific Ocean were sampled with NASA wire-impactors and a FSSP optical particle spectrometer-probe aboard the NASA DC-8 aircraft in early March 1994. Strong variations in aerosol properties, primarily aerosol concentration, lead to derived mid-visible extinctions between 0.003 and 0.5/km. FSSP data usually identified two size-modes. The larger ‘coarse mode’ (radii of 1–3 μm) was assumed to be dust. The composition of the smaller ‘accumulation mode’ (radii of 0.1–0.3 μm) was based on the analysis of the wire-impactor samples, as significant amounts of soot reduce mid-visible single scattering albedos to the 0.87–0.92 range.Radiative forcing simulations investigated the impact of Asian outflow aerosol on atmospheric radiative fluxes and heating rates. Only events with larger optical depths were important. In those events the solar attenuation of the smaller size mode dominated the net-flux losses at the surface, with values similar those of urban-polluted and/or biomass burning aerosol types (as observed during the TARFOX and INDOEX field experiments). In contrast, changes to net-fluxes at the top of the atmosphere (ToA) for outflow cases are less negative—primarily due to the added greenhouse effect of the dust component. For the climate of the Earth-Atmosphere-System, ToA net-flux losses are considered a cooling, ToA net-flux gains are associated with warming. Weak cooling is determined for the Asian outflow cases under cloud-free conditions. The addition of a reported 50% cloud cover below the aerosol layer causes a switch to slight warming.     

The Petroleum Refining Industry—Air Pollution Problems and Control Methods

Polyurethane foam was incorporated as a prefilter on standard hi-volume samplers of the National Air Sampling Network (NASN) in an exploratory study. The foam selectively filtered particles of various sizes. The characteristics of the particles passing through the foam approached the respirable size fraction as defined by reports of the Atomic Energy Commission. The respirable fraction was then collected on a glass-fiber filter. Parameters such as pore size and thickness of the foam, air flow rates, and loadings were studied to determine their effects on the filtration of “respirable” dust. Ambient air was the particulate source, and sizing was accomplished by an Andersen sampler coupled with nephelometric analyses. Some sizing was also done microscopically. The foam was evaluated at several locations to account for possible variations in ambient air over areas of different industrial complexity.     

Optical properties of the San Joaquin Valley aerosol collected during the 1995 integrated monitoring study

Optical, filter chemistry, and cascade impactor data collected during the winter intensive of the IMS95 Study in the San Joaquin Valley (SJV) of California were analyzed to determine the light-extinction efficiency of aerosol species. Regression of light scattering by particles (b_sp) measured by a heated nephelometer without a size selective inlet against PM_2.5 front filter mass gave a scattering efficiency of 3.67±0.05 m²/g with an R² (fraction of variance explained) of 0.94. Division of the aerosol into two components and applying two different corrections to the filter data for nitrate and organic carbon on the backup filter gave scattering efficiencies of 3.7±0.3 or 4.1±0.2 m²/g for the salts composed of sulfate, nitrate, and ammonium and 2.9±0.2 or 3.1±0.2 m²/g for all other species with R² of 0.985 and 0.986. The ambient b_sp measured by an open nephelometer was a simple function of PM_2.5 mass and relative humidity (RH), giving R² of 0.90 and 0.88 for two different RH sensors. Variations in PM_2.5 size distribution and composition did not have an important effect on ambient b_sp. The RH data from each sensor were repeatable enough to show the existence of a simple dependence of aerosol water uptake on RH, but RH sensor calibration uncertainties prevented determining this dependence. Inversion of MOUDI cascade impactor data gave sulfate and nitrate mass median diameters (MMD) between 0.4 and 0.8 μm. Mie scattering calculations based on MOUDI data provided humidity-dependent extinction efficiencies for the principal aerosol chemical species. These efficiencies combined with particle filter data showed that ammonium nitrate was the dominant contributor to wintertime light extinction. Source apportionment showed that light extinction was dominated by emissions sources contributing to the formation of secondary species, especially nitrate. These wintertime data are not expected to apply to summertime in the SJV.