Idle emissions from heavy-duty diesel vehicles: review and recent data

Heavy-duty diesel vehicle idling consumes fuel and reduces atmospheric quality, but its restriction cannot simply be proscribed, because cab heat or air-conditioning provides essential driver comfort. A comprehensive tailpipe emissions database to describe idling impacts is not yet available. This paper presents a substantial data set that incorporates results from the West Virginia University transient engine test cell, the E-55/59 Study and the Gasoline/Diesel PM Split Study. It covered 75 heavy-duty diesel engines and trucks, which were divided into two groups: vehicles with mechanical fuel injection (MFI) and vehicles with electronic fuel injection (EFI). Idle emissions of CO, hydrocarbon (HC), oxides of nitrogen (NOx), particulate matter (PM), and carbon dioxide (CO2) have been reported. Idle CO2 emissions allowed the projection of fuel consumption during idling. Test-to-test variations were observed for repeat idle tests on the same vehicle because of measurement variation, accessory loads, and ambient conditions. Vehicles fitted with EFI, on average, emitted approximately 20 g/hr of CO, 6 g/hr of HC, 86 g/hr of NOx, 1 g/hr of PM, and 4636 g/hr of CO2 during idle. MFI equipped vehicles emitted approximately 35 g/hr of CO, 23 g/hr of HC, 48 g/hr of NOx, 4 g/hr of PM, and 4484 g/hr of CO2, on average, during idle. Vehicles with EFI emitted less idle CO, HC, and PM, which could be attributed to the efficient combustion and superior fuel atomization in EFI systems. Idle NOx, however, increased with EFI, which corresponds with the advancing of timing to improve idle combustion. Fuel injection management did not have any effect on CO2 and, hence, fuel consumption. Use of air conditioning without increasing engine speed increased idle CO2, NOx, PM, HC, and fuel consumption by 25% on average. When the engine speed was elevated from 600 to 1100 revolutions per minute, CO2 and NOx emissions and fuel consumption increased by >150%, whereas PM and HC emissions increased by approximately 100% and 70%, respectively. Six Detroit Diesel Corp. (DDC) Series 60 engines in engine test cell were found to emit less CO, NOx, and PM emissions and consumed fuel at only 75% of the level found in the chassis dynamometer data. This is because fan and compressor loads were absent in the engine test cell.     

Multispecies remote sensing measurements of vehicle emissions on Sherman Way in Van Nuys,California

As part of the 2010 Van Nuys tunnel study, researchers from the University of Denver measured on-road fuel-specific light-duty vehicle emissions from nearly 13,000 vehicles on Sherman Way (0.4 miles west of the tunnel) in Van Nuys, California, with its multispecies Fuel Efficiency Automobile Test (FEAT) remote sensor a week ahead of the tunnel measurements. The remote sensing mean gram per kilogram carbon monoxide (CO), hydrocarbon (HC), and oxide of nitrogen (NO_x) measurements are 8.9% lower, 41% higher, and 24% higher than the tunnel measurements, respectively. The remote sensing CO/NO_x and HC/NO_x mass ratios are 28% lower and 20% higher than the comparable tunnel ratios. Comparisons with the historical tunnel measurements show large reductions in CO, HC, and NO_x over the past 23 yr, but little change in the HC/NO_x mass ratio since 1995. The fleet CO and HC emissions are increasingly dominated by a few gross emitters, with more than a third of the total emissions being contributed by less than 1% of the fleet. An example of this is a 1995 vehicle measured three times with an average HC emission of 419 g/kg fuel (two-stroke snowmobiles average 475 g/kg fuel), responsible for 4% of the total HC emissions. The 2008 economic downturn dramatically reduced the number of new vehicles entering the fleet, leading to an age increase (>1 model year) of the Sherman Way fleet that has increased the fleet's ammonia (NH₃) emissions. The mean NH₃ levels appear little changed from previous measurements collected in the Van Nuys tunnel in 1993. Comparisons between weekday and weekend data show few fleet differences, although the fraction of light-duty diesel vehicles decreased from the weekday (1.7%) to Saturday (1.2%) and Sunday (0.6%).

Implications: On-road remote sensing emission measurements of light-duty vehicles on Sherman Way in Van Nuys, California, show large historical emission reductions for CO and HC emissions despite an older fleet arising from the 2008 economic downturn. Fleet CO and HC emissions are increasingly dominated by a few gross emitters, with a single 1995 vehicle measured being responsible for 4% of the entire fleet's HC emissions. Finding and repairing and/or scrapping as little as 2% of the fleet would reduce on-road tailpipe emissions by as much as 50%. Ammonia emissions have locally increased with the increasing fleet age.     

Idle Emissions from Heavy-Duty Diesel Vehicles: Review and Recent Data

Abstract

Heavy-duty diesel vehicle idling consumes fuel and reduces atmospheric quality, but its restriction cannot simply be proscribed, because cab heat or air-conditioning provides essential driver comfort. A comprehensive tailpipe emissions database to describe idling impacts is not yet available. This paper presents a substantial data set that incorporates results from the West Virginia University transient engine test cell, the E-55/59 Study and the Gasoline/Diesel PM Split Study. It covered 75 heavy-duty diesel engines and trucks, which were divided into two groups: vehicles with mechanical fuel injection (MFI) and vehicles with electronic fuel injection (EFI). Idle emissions of CO, hydrocarbon (HC), oxides of nitrogen (NO_x), particulate matter (PM), and carbon dioxide (CO₂) have been reported. Idle CO₂ emissions allowed the projection of fuel consumption during idling. Test-to-test variations were observed for repeat idle tests on the same vehicle because of measurement variation, accessory loads, and ambient conditions. Vehicles fitted with EFI, on average, emitted [~20 g/hr of CO, 6 g/hr of HC, 86 g/hr of NO_x, 1 g/hr of PM, and 4636 g/hr of CO₂ during idle. MFI equipped vehicles emitted ~35 g/hr of CO, 23 g/hr of HC, 48 g/hr of NO_x, 4 g/hr of PM, and 4484 g/hr of CO₂, on average, during idle. Vehicles with EFI emitted less idleCO, HC, and PM, which could be attributed to the efficient combustion and superior fuel atomization in EFI systems. Idle NO_x, however, increased with EFI, which corresponds with the advancing of timing to improve idle combustion. Fuel injection management did not have any effect on CO₂ and, hence, fuel consumption. Use of air conditioning without increasing engine speed increased idle CO₂, NO_x, PM, HC, and fuel consumption by 25% on average. When the engine speed was elevated from 600 to 1100 revolutions per minute, CO₂ and NO_x emissions and fuel consumption increased by >150%, whereas PM and HC emissions increased by ~100% and 70%, respectively. Six Detroit Diesel Corp. (DDC) Series 60 engines in engine test cell were found to emit less CO, NO_x, and PM emissions and consumed fuel at only 75%of the level found in the chassis dynamometer data. This is because fan and compressor loads were absent in the engine test cell.     

Portable Emission Measurements of Yellowstone Park Snowcoaches and Snowmobiles

Abstract

As part of the National Park Service’s Temporary Winter Use Plans Environmental Assessment, the University of Denver has been collecting in-use tailpipe emissions data from snowcoaches and snowmobiles in Yellowstone National Park. During the winter of 2006, using a portable emissions monitoring system, tailpipe data were collected from 10 snowcoaches and 2 four-stroke snowmobiles. These vehicles were operated over a standard route within the park, and the snowcoaches all carried identical passenger loads. These snowcoaches were newer in age with more advanced fuel management technology than those studied earlier, and average emissions were lower as a result (120, 1.7, and 11 g/mi for carbon monoxide [CO], hydrocarbons [HC], and oxides of nitrogen [NO_x]). Large emissions variability was still observed despite using a standardized route and equal passenger loading. A comparison between five nearly identically equipped snow-coaches that had CO emissions ranging between 12 and 310 g/mi suggests that snow and road conditions are the most important factors behind the large emissions variability observed between modern snowcoaches. The first comprehensive emission measurements, using a portable emissions measurement system, on two snowmobiles showed that computer-controlled fuel management systems have increased fuel economy (>25 mpg) and are a major reason that emissions from these winter vehicles have dropped so dramatically. Using all of the tailpipe emissions data collected to date shows that the two primary winter vehicles in Yellowstone National Park are now very similar in their per-passenger emissions.     

Analysis of Remote Sensing Errors of Omission and Commission Under FTP Conditions

Abstract

Second-by-second modal emissions data from a 73-vehicle fleet of 1990 and 1991 light duty cars and trucks driven on the Federal Test Procedure (FTP) driving cycle were examined to determine remote sensing errors of commission in identifying high emissions vehicles. Results are combined with a similar analysis of errors of omission based on modal FTP data from high emissions vehicles. Extremely low errors of commission combined with modest errors of omission indicate that remote sensing should be very effective in isolating high CO and HC emitting vehicles in a fleet of late model vehicles on the road.     

A Multipurpose Flare Stack for Control of Chemical Process Wastes

Abstract

To test the effectiveness of California’s vehicle inspection/ maintenance (I/M) program, exclusive of vehicle-owner intervention, a fleet of more than 1,100 vehicles that previously had failed California’s Smog Check test were sent to randomly selected Smog Check stations in the Los Angeles area for covert inspections and repairs. The two-speed idle test was used for repairs. For those vehicles that were repaired at the first inspection, their FTP emission reductions were 25%, 14%, and 11% for hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NO_x), respectively, although emissions testing for NO_x was not performed at the Smog Check stations. Idle HC and CO emissions increased for 35% and 43% of the vehicles, respectively, after repairs. This data set shows that most vehicles that fail the Smog Check inspection are only marginal emitters, with 61% and 44% of the total potential for HC and CO emission reductions, respectively, coming from only 10% of the vehicles that currently fail the inspection. When the vehicles were rank-ordered by idle emissions from dirtiest to cleanest, emission reduction costs for the highest-emitting 10% of the fleet averaged $l,100/ton and $250/ton for HC and CO, respectively, attributing all the costs to each pollutant exclusively. For the remaining vehicles, costs increased dramatically.     

On-road remote sensing measurements and fuel-based motor vehicle emission inventory in Hangzhou,China

Motor vehicles are one of the largest sources of air pollutants worldwide. Despite their importance, motor vehicle emissions are inadequately understood and quantified, esp. in developing countries. In this study, the real-world emissions of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxide (NO) were measured using an on-road remote sensing system at five sites in Hangzhou, China in 2004 and 2005. Average emission factors of CO, HC and NO_x for petrol vehicles of different model year, technology class and vehicle type were calculated in grams of pollutant per unit of fuel use (g l⁻¹) from approximately 32,260 petrol vehicles. Because the availability of data used in traditional on-road mobile source estimation methodologies is limited in China, fuel-based approach was implemented to estimate motor vehicle emissions using fuel sales as a measure of vehicle activity, and exhaust emissions factors from remote sensing measurements. The fuel-based exhaust emission inventories were also compared with the results from the recent international vehicle emission (IVE) model. Results show that petrol vehicle fleet in Hangzhou has significantly high CO emissions, relatively high HC and low NO_x, with the average emission factors of 193.07±15.63, 9.51±2.40 and 5.53±0.48 g l⁻¹, respectively. For year 2005 petrol vehicles exhaust emissions contributed with 182,013±16,936, 9107±2255 and 5050±480 metric ton yr⁻¹ of CO, HC and NO_x, respectively. The inventories are 45.5% higher, 6.6% higher and 53.7% lower for CO, HC and NO_x, respectively, than the estimates using IVE travel-based model. In addition, a number of insights about the emission distributions and formation mechanisms have been obtained from an in-depth analysis of these results.     

Speciated hydrocarbon profiles and calculated reactivities of exhaust and evaporative emissions from 82 in-use light-duty Australian vehicles

Mass emissions of non-methane hydrocarbon (NMHC) from 26 pre-1986 and 56 post-1985 catalyst-equipped in-service vehicles were determined from measurements made on a chassis dynamometer using an urban drive cycle. Evaporative emissions were measured on a subset (4 pre-1986 and 8 post-1985) of these vehicles. Average ADR emissions (mg/km) of the individual HCs from the older pre-1986 vehicles were generally 4–7 times the emissions from newer catalyst-equipped vehicles. Evaporative emissions from the older vehicles are also much higher than those of newer vehicles. Exhaust from newer catalyst-equipped vehicles had lower proportions of substituted aromatics and alkenes and higher proportions of lower molecular weight alkanes. The effect of fuel type on the exhaust emissions was also investigated by refuelling 9 of the pre-1986 vehicles with both unleaded and leaded petrol. A 20–40% reduction in HC mass emissions was observed when unleaded petrol was used instead of leaded petrol. Reactivities of the emissions and the contributions from different classes of compounds are also reported. The specific reactivity of the exhaust emissions from newer vehicles was lower than that for older vehicles owing to the smaller proportions of highly reactive alkenes and substituted aromatic species. Moreover, as older vehicles have higher average mass emissions, when considered on a per-km basis, the pre-1986 vehicles have a greater ozone-forming potential than post-1985 vehicles. The specific reactivities of the NMHC (gO₃/gNMHC) of both the heat build and hot soak evaporative emissions were much lower than the exhaust emissions.     

Effect of methyl tertiary butyl ether concentrations on exhaust emissions from gasoline used in the metropolitan area of Mexico City

In this work, the primary objective was to assess the impact of oxygenated fuel on the exhaust emissions from an important fraction of vehicles in the Metropolitan Area of Mexico City (MAMC). The results aim to provide information on the actual effect of MTBE on a fleet that represents more than 60% of the in-use vehicles in the MAMC. Ten vehicles were tested with a low-octane base gasoline, and 10 more with a regular-grade unleaded base gasoline. Three MTBE concentrations, 5, 10, and 15 vol %, were tested following the U.S. Federal Test Procedure (FTP). CO, total HC, and NOx from the exhaust gases were quantitatively evaluated and also characterized for FTP speciated organic emissions. From this data, the O3-forming potential of the fuels was calculated. Results show that for the fleet using low-octane gasoline, the addition of 10% MTBE substantially reduced CO emissions, but total HC concentration in the exhaust showed a modest decrease. For the regular gasoline, the 10% MTBE blend seemed to be the best choice, but there was not a significant decrease in emissions. The specific reactivity of each fuel, expressed in grams of O3 per gram of nonmethane organic gases, increased with MTBE concentration in both cases. This result is important to consider, especially for a region like Mexico City, which has high atmospheric O3 concentrations.     

Real-world fuel use and gaseous emission rates for flex fuel vehicles operated on E85 versus gasoline

Flex fuel vehicles (FFVs) typically operate on gasoline or E85, an 85%/15% volume blend of ethanol and gasoline. Differences in FFV fuel use and tailpipe emission rates are quantified for E85 versus gasoline based on real-world measurements of five FFVs with a portable emissions measurement system (PEMS), supplemented chassis dynamometer data, and estimates from the Motor Vehicle Emission Simulator (MOVES) model. Because of inter-vehicle variability, an individual FFV may have higher nitrogen oxide (NO_x) or carbon monoxide (CO) emission rates on E85 versus gasoline, even though average rates are lower. Based on PEMS data, the comparison of tailpipe emission rates for E85 versus gasoline is sensitive to vehicle-specific power (VSP). For example, although CO emission rates are lower for all VSP modes, they are proportionally lowest at higher VSP. Driving cycles with high power demand are more advantageous with respect to CO emissions, but less advantageous for NO_x. Chassis dynamometer data are available for 121 FFVs at 50,000 useful life miles. Based on the dynamometer data, the average difference in tailpipe emissions for E85 versus gasoline is ?23% for NO_x, ?30% for CO, and no significant difference for hydrocarbons (HC). To account for both the fuel cycle and tailpipe emissions from the vehicle, a life cycle inventory was conducted. Although tailpipe NO_x emissions are lower for E85 versus gasoline for FFVs and thus benefit areas where the vehicles operate, the life cycle NO_x emissions are higher because the NO_x emissions generated during fuel production are higher. The fuel production emissions take place typically in rural areas. Although there are not significant differences in the total HC emissions, there are differences in HC speciation. The net effect of lower tailpipe NO_x emissions and differences in HC speciation on ozone formation should be further evaluated.

Implications: Reported comparisons of flex fuel vehicle (FFV) tailpipe emission rates for E85 versus gasoline have been inconsistent. To date, this is the most comprehensive evaluation of available and new data. The large range of inter-vehicle variability illustrates why prior studies based on small sample sizes led to apparently contradictory findings. E85 leads to significant reductions in tailpipe nitrogen oxide (NO_x) and carbon monoxide (CO) emission rates compared with gasoline, indicating a potential benefit for ozone air quality management in NO_x-limited areas. The comparison of FFV tailpipe emissions between E85 and gasoline is sensitive to power demand and driving cycles.     

Effects of Fuel Type,Driving Cycle,and Emission Status on In-Use Vehicle Exhaust Reactivity

ABSTRACT

The introduction of reformulated gasolines significantly reduced exhaust hydrocarbon (HC) mass emissions, but few data are available concerning how these new fuels affect exhaust reactivity. Similarly, while it is well established that high-emitting vehicles contribute a significant portion of total mobile source HC mass emissions, it is also important to evaluate the exhaust reactivity from these vehicles. The objective of this study was to evaluate the relative influence on in-use vehicle exhaust reactivity of three critical factors: fuel, driving cycle, and vehicle emission status. Nineteen in-use vehicles were tested with seven randomly assigned fuel types and two driving cycles: the Federal Test Procedure (FTP) and the Unified Cycle (UC). Total exhaust reactivity was not statistically different between the FTP and UC cycles but was significantly affected by fuel type. On average, the exhaust reactivity for California Phase 2 fuel was the lowest (16 % below the highest fuel type) among the seven fuels tested for cold start emissions. The average exhaust reactivity for high-emitting vehicles was significantly higher for hot stabilized (11%) and hot start (15%) emissions than for low-emitting vehicles. The exhaust reactivities for the FTP and UC cycles for light-end HCs and carbonyls were significantly different for the hot stabilized mode. There was a significant fuel effect on the mean specific reactivity (SR) for the mid-range HCs, but not for light-end HCs or carbonyls, while vehicle emission status affected the mean SR for all three HC compound classes.     

Characterization of On-Road Vehicle NO Emissions by a TILDAS Remote Sensor

ABSTRACT

A tunable infrared laser differential absorption spectrometer (TILDAS) was used to remotely sense the nitric oxide (NO) emissions from 1,473 on-road vehicles. The real-world measurement precision of this instrument in the limit of low NO concentration is 5 ppm of the vehicle exhaust, which corresponds to a 3o detection limit of 15 ppm. Our analysis of the distribution of negative concentration measurements produced during this experiment supports this claim, showing that the instrumental noise for this set of measurements was at most 8 ppm in the limit of low NO concentration. The high sensitivity of this instrument allowed us to measure the NO emissions of even the cleanest vehicles. The measured vehicle fleet NO emissions closely fit a gamma distribution with 10% of the fleet contributing about 50% of the total fleet emissions. Newer vehicles had lower NO emissions than older ones, but high NO emitters were found in every vehicle age cohort. On a vehicle-by-vehicle basis, NO emissions correlated very weakly with vehicle velocity, acceleration, power per unit mass, carbon monoxide (CO) emissions, and hydrocarbon (HC) emissions. High NO emitting vehicles could not be identified by remote sensing of CO or HC emissions and vice versa. When we compared the NO emissions for 117 vehicles measured more than one time, about half of the high NO emitters were found to be very consistent, while the other half varied significantly.     

Prospects of inspection and maintenance of two-wheelers in India.

Two-wheeler vehicles in Delhi, India--roughly 70% of the total vehicle fleet--are responsible for a significant portion of the city's vehicle emissions and petroleum consumption. An inspection and maintenance (I/M) program that ensures vehicle emission control systems are well maintained can complement other emission reduction strategies. This paper presents the initial findings of extensive data collected on vehicle characteristics and emissions for two-wheeler vehicles operating in Delhi in a series of I/M camps conducted by the Society of Indian Automobile Manufacturers and various partners in late 1999. The analysis shows idle HC and CO emissions [measured in terms of parts per million (ppm) and volume % (vol %), respectively] in a slow declining trend with subsequent model years, reflecting tighter emission standards and more advanced emission technologies. The I/M benefits--3 vol % and 39% reduction in idle and mass CO, respectively; 40 vol % and 22% reduction in idle and mass HC, respectively; and a 10-20% increase in fuel efficiency--were higher than those reported in the literature. Although these benefits are substantial, any implementation strategy needs to consider cost-effectiveness. In the present study, only 10% of vehicles--contributing 22% of the total vehicle emissions--failed the idle CO standard. Fleet emissions data variability necessitates a large sample size to develop a baseline for the vehicle fleet, but a smaller, scientifically designed sample and better data collection quality could periodically track the benefits at future camps.     

Comparison of the SCAQS Tunnel Study with Other On Road Vehicle Emission Data

The Van Nuys Tunnel experiment conducted in 1987 by Ingalls et al. (see A&WMA Paper 89-137.3), to verify automotive emission inventories as part of the Southern California Air Quality Study (SCAQS), gave higher CO and HC emission-rate values than expected on the basis of automotive-emission models—by factors of approximately 3 and 4, respectively. The CO/NO_X and HC/NO_X emission-rate ratios moreover were higher than expected—by similar factors (NO_X emission rates were about as expected). The purpose of the present paper is to review the literature on dynamometer and on-road (in tunnels and along roadways) testing of in-use vehicles, and on urban-air CO/HC/NO_X concentration ratios, to see whether the Van Nuys Tunnel results are reasonable in terms of previous experience. The conclusions are that (1) on-road CO and HC emissions higher than expected have been reported before, (2) on-road CO and HC emissions consistent with the Van Nuys Tunnel results have been reported before, and (3) on-road CO/NO_X and HC/NO_X emission-rate ratios higher than expected have been reported before. The Van Nuys Tunnel NO_X results actually are lower than in other on-road experiments, and the CO/NO_X and HC/NO_X ratios consequently are higher. The higher-than-predicted CO/NO_X and HC/NO_X ratios at Van Nuys and other on-road sites suggest richer operation on-road than predicted or than observed in the inuse- vehicle dynamometer tests which serve as the model inputs. Support for these suggestions and conclusions is found in comparison of urban-air and emission-inventory HC/NO_X ratios.     

Remote Sensing Data and a Potential Model of Vehicle Exhaust Emissions

In June 1991, General Motors Research and Development Center (GMR&D) participated in a remote sensing study conducted by the California Air Resources Board and the U. S. Environmental Protection Agency. During this study, the GMR&D remote sensor was used to measure the carbon monoxide (CO) and hydrocarbon (HC) emissions from approximately 15,000 vehicles. The vehicle type (passenger car, light-duty truck, or medium/heavy-duty truck), manufacturer, and model year were identified for each vehicle by acquiring registration data from the state of California. Analyses were performed separately for each vehicle type and for passenger cars by separate model years. The data indicate that the passenger cars with the highest 10% of CO emissions generated approximately 58% of the total CO from all cars. Similarly, the 10% highest HC-emitting cars generated 65% of the total HC from cars. It was found that for each model year of vehicle, the distribution of emission concentrations followed a logarithmic relationship. The logarithmic functions that describe these relationships can be used to estimate the fraction of vehicles that emitted at or above any given concentration of CO or HC. However, these logarithmic functions only describe measured distributions for vehicles emitting more than 1% CO and 0.015% HC.     

The Formation of Mg3Ca(S04)4 during the Sulfation Reaction of Dolomite

Abstract

Inspection and maintenance programs for motor vehicles in the United States increasingly use loaded mode mass emissions testing (IM240). A method was developed to predict mass emission rates and mass emission changes, particularly from repair benefits, using a low-cost, portable four-gas non-dispersive infrared (NDIR) vehicle exhaust gas analyzer. A single vehicle was tested several times with the analyzer while on the dynamometer and undergoing successive repairs. Excellent correlations for CO and HC were observed. Five vehicles were measured using an on-road driving loop before and after emissions-related repairs, while another three vehicles were tested with no repairs performed. The on-road concentration data used to guide the repair process were converted to grams per gallon; when divided by estimated miles per gallon, this gave grams per mile emissions for comparison to IM240. Correlation coefficients (r²) of 0.87 for CO and 0.76 for HC were achieved for the 13 tests. The linear correlations between IM240 and emissions measured by this method would allow repair facilities to perform a relatively inexpensive test for diagnostic purposes and to estimate repair effectiveness without the need for a dynamometer.     

An Investigation of Idle Emissions Inspection and Maintenance at Altitude

Idle emissions inspection and maintenance was evaluated using a sample of 300 privately owned 1964 through 1973 model-year vehicles operating in the Denver metropolitan area. Ten privately owned stations, licensed by the State of Colorado to perform vehicle safety inspections, were utilized to conduct idle emissions inspection and subsequent maintenance of failed vehicles. Exhaust hydrocarbon (HC) and carbon monoxide (CO) reduction as measured by the 1975 Environmental Protection Agency (EPA) mass emission testing procedures was indicated to be 13% and 8% respectively at a 50 % rejection rate. The average maintenance cost to achieve the reduction was $11.32 per failed vehicle.

The adjustment and repair procedures provided to participating garages were sufficient to achieve significant emissions reduction and training provided to garage personnel was adequate. However, several problems were experienced with station personnel relative to data transmittal and inspection pass/fail limits. Problems were also experienced with respect to correlations between laboratory and garage-type analytical instrumentation.     

Estimations of real-world N2O emissions from road vehicles by means of measurements in a traffic tunnel

Ambient air measurements of N2O, NOx, CO, and HC based on grab sampling were conducted in a major traffic tunnel in Sweden, that carries up to 4,000 vehicles per hour, in order to estimate real-world emissions of N2O for road traffic. Two different methods--relative and mass balance-were used to calculate a N2O emission factor for the mixed vehicle fleet, which gave an average emission factor, at average speeds of 30-70 km/h, of approximately 25 mg N2O/ km, with a range of 7-56 mg/km.     

Product Guide/1970

Abstract

In Mexico City, the use and composition of fuels determine that carbon monoxide (CO) comes mostly from mobile sources, and sulfur dioxide (SO₂) from fixed and mobile sources. By simultaneously measuring hydrocarbons (HC), CO, and SO₂ in the atmosphere of Mexico City, the relative amounts coming from different sources can be estimated. Assuming that some HC are emitted proportionally to CO emissions, we can establish that [HC]₁= m1? [CO], where the proportionality constant ml corresponds to the ratio of emissions factor for HC and CO in mobile sources. Similarly for fuels containing sulfur, it can be assumed that [HC]₂ = m2 ? [SO₂]. In this way, the total HC are [HC]_total=[HC]₀+ ml ? [CO]+ m2 ? [SO₂], where [HC]₀ corresponds mainly to other sources like solvent evaporation, gas consumption, and natural emissions. In this way, it can be estimated that in Mexico City 75% of average HC comes from mobile sources, 5% from sulfur-related sources, and 19% from natural sources and solvent evaporation. Compared with the HC/CO ratio measured in the exhaust pipe of vehicles, we estimated that 70% of HC emitted from mobile sources are evaporative losses, and only 30% come through the exhaust system.     

Effects of engine speed and accessory load on idling emissions from heavy-duty diesel truck engines

A nontrivial portion of heavy-duty vehicle emissions of NOx and particulate matter (PM) occurs during idling. Regulators and the environmental community are interested in curtailing truck idling emissions, but current emissions models do not characterize them accurately, and little quantitative data exist to evaluate the relative effectiveness of various policies. The objectives of this study were to quantify the effect of accessory loading and engine speed on idling emissions from a properly functioning, modern, heavy-duty diesel truck and to compare these results with data from earlier model year vehicles. It was found that emissions during idling varied greatly as a function of engine model year, engine speed, and accessory load conditions. For the 1999 model year Class 8 truck tested, raising the engine speed from 600 to 1050 rpm and turning on the air conditioning resulted in a 2.5-fold increase in NOx emissions in grams per hour, a 2-fold increase in CO2 emissions, and a 5-fold increase in CO emissions while idling. On a grams per gallon fuel basis, NOx emissions while idling were approximately twice as high as those at 55 mph. The CO2 emissions at the two conditions were closer. The NOx emissions from the 1999 truck while idling with air conditioning running were slightly more than those of two 1990 model year trucks under equivalent conditions, and the hydrocarbon (HC) and CO emissions were significantly lower. It was found that the NOx emissions used in the California Air Resources Board's (CARB) EMFAC2000 and the U.S. Environmental Protection Agency's (EPA) MOBILE5b emissions inventory models were lower than those measured in all of the idling conditions tested on the 1999 truck.