Carbon tax policy analysis based on distribution channel strategy

Environmental Science and Pollution Research - This paper establishes a theoretical model to study the carbon tax policy based on a firm’s different distribution channel strategy. First, we...     

Recommended Standard Method for Continuing Dust Fall Survey (APM-1, Revision 1)

The suggested standard method of dust fall collection, as set forth in the following sections, is presented in an effort to promote a uniform approach to measurement of rate of dust fall     

Government/Industry Cost Sharing for Air Pollution Control

Several existing federal and state provisions act to reduce the cost to in dustry of controlling air pollution. Included are the federal corporate income tax, depreciation allowances, investment credits, small Business Administration loans, Economic Development Administration aid, and state tax laws. These provisions give government assistance to industry amounting to as much as 59 percent of the cost of air pollution control. Numerous bills have been introduced in Congress that would give additional government aid to industry in the form of special across-the-board tax allowances for air pollution control equipment. A typical bill of this type would result in the government bearing an additional 11 percent of these costs. There are several possible objectives for this kind of additional aid; however, none of these seem valid when the amount of present assistance is recognized. From this analysis, it would seem that additional across-the-board tax subsidies for air pollution control equipment are neither required nor advisable. Future studies and/or experience may show certain firms or industries for which air pollution control will be too great a burden and for which additional government assistance is advisable. When such cases are found, legislation should be enacted only after the pros and cons of the various assistance methods are considered.     

An assessment of the aggregate impacts of the proposed reduction in the motor fuels tax in the United States

The analysis in this paper examines the impact of reducing the excise tax on gasoline and diesel fuel on the United States economy. The analytical approach used consists of a computable general equilibrium model composed of fourteen producing sectors, fourteen consuming sectors, six household categories classified by income and the government. The effects of a 4.3 cents per gallon reduction in the excise tax on gasoline and diesel fuel on prices and quantities are examined. The results suggest, for example, that a decrease in the tax would result in higher output by the producing sectors (by about $2.86 billion), and expansion in the consumption of goods and services (by about $3.48 billion), and an increase in welfare (by about $3.59 billion). The government would realise a decrease in revenue of about $2.37 billion. When subjected to a sensitivity analysis, the results are reasonably robust with regard to the assumption of the values of the substitution elasticities.     

Establishing and Evaluating the Risk Implications of Uniform Soil Remediation Goals

Abstract

There is growing interest in the establishment of uniform, concentration-based soil remediation goals to accelerate the cleanup of contaminated sites and to provide consistency in the extent of cleanup required for similar sites. If uniform goals are used in a region, post-remediation risk will vary across sites due to regional variability in site properties. Thus far, of the national and state agencies that have established or proposed uniform concentration guidelines, none have quantified the regional variability in risk that is likely to result with their use as remediation goals.

This paper describes a methodology for evaluating regional cancer risk variability resulting from use of uniform, concentration-based soil remediation goals, presents an example application of the methodology, and examines its utility for establishing uniform goals for organic contaminants in soil. The methodology is based on the integrated transport, fate, exposure, and risk model SoilRisk. Also addressed is the issue of contaminants for which regional risk variability is expected to be large with use of uniform soil remediation goals. An approach is described for reducing such variability by development of alternative uniform contaminant concentration levels for categories of sites differentiated by site geographic location or physical-chemical properties.     

Impact analysis of carbon taxes on the steamcoal and natural gas market in the eastern United States: a linear complementarity model

The impact of a federal excise tax on Appalachian steamcoal on the consumption and production of steamcoal and natural gas is investigated. To examine the comprehensive effects of such taxes, the linear complementarity model is used to ensure consistent results. Predictions on coal and natural gas prices are also made for useful policy implementations.     

Application of a stochastic, Weibull probability generator for replacing missing data on ambient concentrations of gaseous pollutants

A stochastic, three-parameter, Weibull frequency distribution, probability generator was tested by using theoretical data. Subsequently, it was applied to replace missing values of hourly atmospheric concentrations of trace gases that were continuously monitored at three study sites, for 2 years. The results were highly accurate and realistic. The cumulative means and the medians calculated by the Weibull method were intermediate between corresponding values calculated by uniform substitution of missing values with 'zero' or with half of the minimum detection limit of the appropriate measurement instrument used. Furthermore, the Weibull method allowed the replacement of as many as 100 missing values on either side of a measured data sub-set, without altering the overall characteristics of the true frequency distribution of the entire data set.     

Composting and bioremediation process evaluation of wood waste materials generated from the construction and demolition industry

The suitability of using bioremediation and composting techniques for diverting construction and demolition (C&D) waste from landfill has been validated in this study. Different timber products from C&D waste have been composted using various composting approaches. The present work demonstrates the quality of compost produced as a result of composting of mixed board product wood waste, which is frequently obtained from the construction and demolition industry. Three compost mixes were prepared by mixing shredded chip board, medium density fibre, hardboard and melamine. Poultry manure, Eco-Bio mixture and green waste were used as nutrient supplements. The results revealed that compost produced from mixtures of poultry manure and green waste used as nutrient supplements improved the performance in plant growth trials (phytotoxicity tests). Results obtained from the experimental study clearly indicate that the composts produced comply with the criterion suggested in BSI PAS 100 (A specification for compost materials) for use in different applications. Composting can also be demonstrated to be a very practical approach to material management including transport reduction to and from the site. The economic suitability of the process will be improved with the increase in landfill tax. In the current regulatory scenario, it is recommended that these materials should be composted at a centralised facility.     

A theoretical model of air and steam co-injection to prevent the downward migration of DNAPLs during steam-enhanced extraction

When steam is injected into soil containing a dense volatile non-aqueous phase liquid contaminant the DNAPL vaporized within the heated soil region condenses and accumulates ahead of the steam condensation front. If enough DNAPL accumulates, gravitational forces can overcome trapping forces allowing the liquid contaminant to flow downward. By injecting air with steam, a portion of the DNAPL vapor remains suspended in equilibrium with the air, decreasing liquid contaminant accumulation ahead of the steam condensation front, and thus reducing the possibility of downward migration. In this work, a one-dimensional theoretical model is developed to predict the injection ratio of air to steam that will prevent the accumulation of volatile DNAPLs. The contaminated region is modeled as a one-dimensional homogeneous porous medium with an initially uniform distribution of a single component contaminant. Mass and energy balances are combined to determine the injection ratio of air to steam that eliminates accumulation of the contaminant ahead of the steam condensation front, and hence reduces the possibility of downward migration. The minimum injection ratio that eliminates accumulation is defined as the optimum injection ratio. Example calculations are presented for three DNAPLs, carbon tetrachloride (CCl4), trichloroethylene (TCE), and perchloroethylene (PCE). The optimum injection ratio of air to steam is shown to depend on the initial saturation and the volatility of the liquid contaminant. Numerical simulation results are presented to validate the model, and to illustrate downward migration for ratios less than optimum. Optimum injection ratios determined from numerical simulations are shown to be in good agreement with the theoretical model.     

Use of two different acidic aerosol samplers to measure acidic aerosols in Hsinchu, Taiwan

Acidic aerosol concentrations measured by an annular denuder system (ADS) and a honeycomb denuder system (HDS) in Hsinchu, Taiwan, were compared. Aerosols were also sampled by a MOUDI (micro-orifice uniform deposit impactor) and analyzed by an ion chromatograph to determine the size distributions of different species. Using the measured aerosol size distribution, theoretical analysis showed that positive HNO3 artifact due to volatilization of NH4NO3 is generally negligible for both samplers. Comparing two different denuder samplers, the average concentration of HNO3 measured by the ADS was found to be lower than that measured by the HDS, while the difference between the two samplers for the average concentration of other species was found to be within +/- 15%. A possible cause of the difference in HNO3 concentrations is due to a greater loss of HNO3 in the cyclone used by the ADS than in the impactor used by the HDS. The study also showed incomplete absorption of the evaporated HCl and HNO3 from the particles on the Teflon filter by the first nylon filter in the filter pack of the ADS. Collection efficiency and capacity of HCl and HNO3 by the nylon filters need further investigation.     

How to improve the function of government carbon tax in promoting enterprise carbon emission reduction: from the perspective of three-stage dynamic game

Environmental Science and Pollution Research - Flexible strategy of carbon tax is an important chip for the government to promote the implementation of carbon emission reduction. However,...     

Captive Insurance Companies and the Management of Environmental Risks

Recent publicity has focused on the crisis in the market for commercial liability insurance. Industries and professionals concerned with air pollution are among those facing an acute shortage of insurance coverage. Captive insurance companies are gaining popularity as a means of securing comprehensive pollution liability coverage. Captives are separate corporations established by companies with similar risk management problems to write policies covering pollution emissions. Federal tax law requires that captives be set up properly, with transfer and distribution of risk, before premiums paid by the member companies are deductible. Financial responsibility requirements of the EPA are being redesigned, and may be favorable to the use of captives. Six states and several off-shore countries have statutes allowing captive insurance companies. Attention to practical details can lead to success in using captives to secure business advantages as well as protection from the risk of environmental impairment. Several of such considerations are discussed in light of the tax, environmental, and state regulatory issues relevant to the question, with an eye toward giving practical legal advice for structuring captives.     

城市规划的环境影响评价研究初探

环境影响评价法的颁布是中国环境影响评价的一个新阶段。中国至今尚无明确的、系统的规划环境影响评价的技术导则和规范,其评价理论仍在探索之中。分析了国内外规划环境影响评价的历史和现状。从区域环境影响评价的实践经验总结出了城市规划环境影响评价应强调城市发展的可持续性。探讨了该层次评价的介入时间、评价原则、环境影响因素识别及评价内容,提出从生态合理性、绿色化程度等方面考虑城市规划的生态环境影响。     

Influence of input uncertainty on prediction of within-field pesticide leaching risks

Previous research has suggested that pesticide losses at the field scale can be dominated by a small proportion of the field area. The objective of this study was to investigate whether site-specific applications (i.e. avoiding high-risk areas) at the field scale can contribute to a reduction of pesticide leaching despite uncertainty in the underlying model-based leaching risk map. Using a meta-model of the dual-permeability model MACRO, the annual average pesticide leaching concentrations were estimated for 162 sample sites on a 47 ha field. The procedure was repeated for different scenarios describing different patterns of spatial variation of degradation half-lives and the partition coefficient to soil organic carbon. To account for interpolation uncertainty, maps of predicted pesticide leaching risk were produced by the method of sequential Gaussian simulation. The results of the case study show that larger reductions of predicted leaching were achieved by site-specific application than by that of a comparable uniform dose reduction. Hence, site-specific-applications may be a feasible method to reduce pesticide leaching at the field-scale providing that the model approach gives reasonable estimates of the spatial pattern of pesticide leaching.     

Macrodispersion by diverging radial flows in randomly heterogeneous porous media

Radial flow takes place in a heterogeneous porous formation where the transmissivity T is modelled as a stationary random space function (RSF). The steady flow is driven by a given rate, and the mean velocity is radial. A pulse-like of a tracer is injected in the porous formation, and the thin plume spreads due to the fluctuations of the velocity which results a RSF as well. Transport is characterized by the mean front, and by the second spatial moment of the plume. We are primarily interested in tracer macrodispersion modelling. With the neglect of pore-scale dispersion, macrodispersion coefficients are computed at the second order of approximation, without neglecting the head-gradient fluctuations. Although transport is non-ergodic at the source, it is shown that ergodicity is achieved at small distances from the source. This is due to the fact that close to the source local velocities are quite large, and therefore solute particles become uncorrelated very soon. Under ergodic conditions, we compare macrodispersion mechanism in radial flows with that occurring in mean uniform flows. At short distances the spreading effect is highly enhanced by the large variability of the flow field, whereas at large distances transport exhibits a lesser dispersion due to the reduction of velocities. This supports the explanation provided by Indelman and Dagan (1999) to justify why the macrodispersivity is found smaller than that pertaining to mean uniform flows. The model is tested against a tracer transport experiment (Fernàndez-Garcia et al., 2004) by comparing the theoretical and experimental breakthrough curves. The accordance with real data, that is achieved without any fitting to concentration values, strengthens the capability of the proposed model to grasp the main features of such an experiment, the approximations as well as experimental uncertainties notwithstanding.     

Dry Removal of Gaseous Fluorine Pollutants

The conservation equations governing buoyant plume rise are solved for the case of non-uniform wind conditions. A power law is selected to represent the actual wind profile. Analytical solutions are presented both for uniformly stable and neutral atmospheric conditions. These solutions are shown to be of the same form as those obtained in the simpler uniform case but with the plume rise now depending explicitly on the wind speed shear. A sensitivity analysis of the effects on plume rise of typical variation in wind shear and entrainment reveals that the two quantities have an almost equal effect therefore justifying the use of the present model. To simplify computations a “uniform wind” is introduced such that when used in conjunction with Briggs' equations the results become consistent with those of the present theory.     

A Cournot competition model with the uniform pollution tariff: an application to NAFTA

This paper investigates the impact of a uniform pollution tariff on production, consumption and consumer welfare in the framework of the Cournot competition. It suggests that the uniform pollution tariff would raise the welfare of US consumers. However, it would penalise the higher-cost producer in the country where environmental regulations are more stringent. The policy implication is that economic integration, such as NAFTA, should take discriminatory pollution tariffs into consideration.     

Sources and distribution of polycyclic aromatic hydrocarbons in sediments from the Spanish northern continental shelf. Assessment of spatial and temporal trends

The distribution of polycyclic aromatic hydrocarbons was determined in surface sediments collected at 36 stations along the Spanish Northern continental shelf in March and September 2003, and February 2005. Concentrations of PAHs (Σ13 parent components) were in the range of 22-47528 μg/kg dw, the highest values corresponding to coastal urban-industrial hotspots and decreasing offshore. Sediment quality guidelines (SQGs) showed that concentrations of total PAHs were below the threshold effect level (TEC) in 27 stations (81%) and above in 7, two of which (Gijon and Bilbao) were above the probable effect concentration (PEC). The detailed study of diagnostic ratios suggested a rather uniform mixture of petrogenic and pyrolytic PAH sources along the continental shelf, with a slight decrease of the latter moving westwards and offshore. In order to assess the incidence of sediment sampling on the variability of the results, selected stations were also monitored in February and September 2004 and September 2005. The average field variance of the values obtained for each station was 31% that decreased to 23% when the values were normalized to TOC.     

Organochlorine, PCB, PAH, and metal concentrations in eggs of loggerhead sea turtles (Caretta caretta) from northwest Florida, USA

Composite samples of unhatched and physically unaltered loggerhead sea turtle, Caretta caretta, eggs collected from 20 nests along northwest Florida were analyzed for organochlorine pesticides (OCPs), polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons (PAHs), and metals. Chemical analyses revealed that turtle eggs contained detectable amounts of metals, PAHs, and PCBs. Only one OCP, p,p'-DDD, was detected, and its presence was restricted to eggs from two nesting sites. None of the PCB concentrations exceeded the Food and Drug Administration's (FDA) action limit. Concentrations of dioxin-like PCB congeners, 105, 118, and 126, and total PCBs were also detected and are contributors to the toxic burden of loggerhead sea turtle eggs. Concentrations of PAHs, 1,2,5,6-dibenzanthracene, 1-methyl naphthalene, C1-naphthalene and naphthalene were variable at nesting sites. Comparison of mean metal burdens in eggs from different beaches suggested that no uniform geographic gradients exist. Presence of OCPs, PCBs, PAHs and metals and their additive or synergistic toxicity is a concern to loggerhead sea turtle eggs; however, additive or synergistic impacts for loggerhead sea turtles are largely undocumented.