The Need for Representative Ambient Air Carbon Monoxide Sampling

Recent investigations have indicated that ambient air CO measurements may not reflect population exposure to CO. The lack of correlation may be due to improper siting of CO instruments, improper interpretation of air quality data, or both. Studies of population carboxy-hemoglobin levels are evaluated and compared with ambient air data.,

No significant correlation was found between median population COHb levels and reductions in CO concentrations required to meet ambient air standards when calculations used to estimate reductions were based on the second highest 8 hour average. However, calculated reductions based on annual average concentrations and a trend analysis technique correlated significantly with COHb levels in five cities from which both CAMP and COHb data were available.

Studies to determine the nature of the relationship between ambient air CO concentrations and population COHb levels are needed. The differences between the Occupational Safety and Health Act Regulations and the National Ambient Air Standards for carbon monoxide should be scrutinized to determine if a redefinition of the standards or their applicability is warranted. A reevaluation of the controls necessary to make reductions in population COHb burden may be necessary.     

Ambient Air Quality and Automotive Emission Control

This paper is concerned with uncertainties involved in projecting ambient air quality. Ambient air quality was projected by assuming a linear dependence on estimated future emissions. Future automotive emissions were estimated by a method recommended by EPA. Projections were made for the locations reported to have the highest ambient air concentrations of each pollutant; Chicago for carbon monoxide and the California South Coast Air Basin for hydrocarbon and oxidant. The sensitivity of the projections to several input parameters was determined.

The uncertainty in projection of air quality due to the use of a maximum, once-per-year concentration is large. For example, the reduction in total CO emissions in Chicago in 1975, necessary to meet the air quality standard, was as high as 68% or as low as 26%, depending on whether the historic high, 8 hr average concentration of 44 ppm or the 1970 maximum of 21 ppm was used. The effects of uncertainties in growth rates and fraction of emissions attributed to the automobile were also sizeable. Differences in automotive growth rate had a large near-term effect on projected concentrations, while differences in nonautomotive growth rate or fraction of emissions attributed to the automobile had a large long-term effect. The effect of 1975 interim automotive emission standards on projected air quality was negligible when compared with projected air quality based on the previous Federal automotive emission standards for 1975.     

The Annual Average: An Alternative to the Second Highest Value as a Measure of Air Quality

It is common practice to use the second highest value both in determining compliance with the once-per-year air quality standards (AQS) and as a measure of air quality in pollutant trend studies and rollback calculations. A study of the variation in the second highest 8 hr carbon monoxide concentration observed at the CAMP stations 1962-72 is presented. It is shown that, for a given annual average, the second highest value can differ by a factor of 2 due to random variation. The annual average is linearly related to the observed average of the second highest value and is shown to be a good predictor of the percent of time the carbon monoxide AQS is exceeded. It is concluded that the annual average, which is less variable and not as greatly influenced by erroneous measurements, is the preferred measure of air quality for trend studies and air quality projections.     

The Effect of California’s Wintertime Oxygenated Fuels Program on Ambient Carbon Monoxide Concentrations

Abstract

The U.S. Environmental Protection Agency (EPA) mandated the use of oxygenated gasoline beginning in the winter of 1992 to reduce the unhealthful carbon monoxide concentrations in many urban areas. The California Air Resources Board (CARB), weighing the potential effects of the program on other pollutants, implemented a modified version of the federal wintertime oxygenated fuels program. In California, the number of violations of the carbon monoxide air quality standard during the three winters associated with the program was dramatically lower than during any winter prior to the program. Because meteorological conditions during the program were very favorable for dispersion of pollutants, any analysis of the impacts of the program must account for the influence of variable meteorological conditions. Analyses of ambient pollutant concentrations suggest that most of the air quality improvement was due to increased atmospheric dispersion. The analyses presented here account for the large influence of meteorology on ambient concentrations and indicate that California’s modified oxygenated fuels program was responsible for an approximately 5–10% reduction in mean ambient carbon monoxide concentrations, depending on the statistical approach used.     

A Regulatory Analysis

The information presented in this paper is directed to those individuals interested in future air quality control programs aimed at areas that are attaining one or more air quality ambient standards. Section 116 of the Clean Air Act, as amended, requires the Environmental Protection Agency to promulgate regulations for the prevention of significant deterioration (PSD) of air quality in order to protect the nation's clean air resources from hydrocarbons, carbon monoxide, ozone, nitrogen oxides, and lead (Set II pollutants). This program will affect industry siting in many areas of the country, particularly in the rural, undeveloped areas. Among the many alternatives currently being considered by EPA to meet the PSD Set II goals are emission management systems, marketable emission permits, air quality increments, emission fees, and control of transportation related sources. The final regulation may be a combination of several options or may present several alternatives from which a State would choose its specific program.     

汽车内微环境空气污染的初步探究

为了研究车内的污染水平,在2004-04-10至2004-06-20对车内空气进行了采样和分析.对车龄在2年内的91种型号轿车的车内微环境进行了静态检测,有效检测车辆共计802辆,同时对比检测20辆2002年以前出厂的旧车.检测项目包括甲醛、苯、甲苯、二甲苯和CO等.参照国家室内空气质量标准,新车中甲苯浓度超标率达82%,苯和甲醛浓度的超标率分别为75%和24%.在被检测车辆中,甲醛、苯、甲苯和二甲苯浓度均是新车比旧车高,只有CO浓度是旧车比新车高.初步分析判断苯系物主要来源于车内的胶粘剂,甲醛来自于车椅座套和座垫等,CO来源于发动机排放残留.     

Model for estimation of traffic pollutant levels in northern communities

Using models to estimate the contribution of traffic to air pollution levels from known traffic data typically requires the knowledge of model parameters such as emission factors and meteorological conditions. This paper presents a state-space model analysis method that does not require the knowledge of model parameters; these parameters are identified from measured traffic and ambient air quality data. This method was used to analyze carbon monoxide (CO) in downtown Fairbanks, AK, which is the community of focus for this paper. It was found that traffic contributed, on average, 53% to the total CO levels over the last six winters. The correlation coefficient between the measured and model-predicted daily profiles of the CO concentration was 0.98, and the results were in good agreement with earlier findings obtained via a thorough CO emission inventory. This justified the usability of the method and it was further used to analyze fine particulate matter (PM2.5) in downtown Fairbanks. It was found that traffic contributed, on average, approximately 30% to the total PM2.5 levels over the last six winters. The correlation coefficient between the measured and model-predicted daily profiles of the PM2.5 concentration was 0.98.     

Comparison of air pollutant emissions among mega-cities

Ambient measurements of hydrocarbons, carbon monoxide and nitrogen oxides from three mega-cities (Beijing, Mexico City, Tokyo) are compared with similar measurements from US cities in the mid-1980s and the early 2000s. The common hydrocarbon pattern seen in all data sets suggests that emissions associated with gasoline-fueled vehicles dominate in all of these cities. This commonality suggests that it will be efficient and, ultimately, cost effective to proceed with vehicular emission controls in most emerging mega-cities, while proceeding with development of more locally appropriate air quality control strategies through emissions inventory development and ambient air monitoring. Over the three decades covered by the US data sets, the hydrocarbon emissions decreased by a significant factor (something like an order of magnitude), which is greater than suggested by emission inventories, particularly the EDGAR international inventory. The ambient hydrocarbon and CO concentrations reported for the three non-US mega-cities are higher than present US ambient concentrations, but lower than those observed in the 1980s in the US. The one exception to the preceding statement is the high concentrations of CO observed in Beijing, which apparently have a large regional contribution.     

Estimating Future NO2 Levels in the Greater Los Angeles Area by Source–Type Contribution

Two indicator pollutants, carbon monoxide (CO) for mobile source influence and sulfur dioxide (SO₂) for stationary source influence, were used to estimate source-type contributions to ambient NO₂ levels in a base year and to predict NO₂ concentrations in a future year. For a specific source-receptor pair, the so-called influence coefficient of each of three source categories (mobile sources, power plants, and other stationary sources) was determined empirically from concurrent measurements of CO and SO₂ concentrations at the receptor site and CO and SO₂ emissions from each source category in the source area. Those coefficients, which are considered time invariant, were used in conjunction with the base year and future year NO _x emission values to estimate source-type contribution to ambient NO₂ levels at seven study sites selected from the Greater Los Angeles area for both the base year period, 1974 through 1976, and the future goal year of 1987 in which the air quality standards for NO₂ are to be attained. The estimated NO₂ air quality at the seven sites is found to meet the national annual standard of 5 pphm and over 99.9% of total hours, the California 1-hr NO₂ standard of 25 pphm in 1987. The estimated power plant contributions to ambient NO₂ levels are found to be considerably smaller than those to total NO _x emissions in the area. Providing that reasonably complete air quality and emissions data are available, the present analysis method may prove to be a useful tool in evaluating source contributions to both short-term peak and long-term average NO₂ concentrations for use in control strategy development.     

Near-roadway monitoring of vehicle emissions as a function of mode of operation for light-duty vehicles

Determination of the effect of vehicle emissions on air quality near roadways is important because vehicles are a major source of air pollution. A near-roadway monitoring program was undertaken in Chicago between August 4 and October 30, 2014, to measure ultrafine particles, carbon dioxide, carbon monoxide, traffic volume and speed, and wind direction and speed. The objective of this study was to develop a method to relate short-term changes in traffic mode of operation to air quality near roadways using data averaged over 5-min intervals to provide a better understanding of the processes controlling air pollution concentrations near roadways. Three different types of data analysis are provided to demonstrate the type of results that can be obtained from a near-roadway sampling program based on 5-min measurements: (1) development of vehicle emission factors (EFs) for ultrafine particles as a function of vehicle mode of operation, (2) comparison of measured and modeled CO₂ concentrations, and (3) application of dispersion models to determine concentrations near roadways. EFs for ultrafine particles are developed that are a function of traffic volume and mode of operation (free flow and congestion) for light-duty vehicles (LDVs) under real-world conditions. Two air quality models—CALINE4 (California Line Source Dispersion Model, version 4) and AERMOD (American Meteorological Society/U.S. Environmental Protection Agency Regulatory Model)—are used to predict the ultrafine particulate concentrations near roadways for comparison with measured concentrations. When using CALINE4 to predict air quality levels in the mixing cell, changes in surface roughness and stability class have no effect on the predicted concentrations. However, when using AERMOD to predict air quality in the mixing cell, changes in surface roughness have a significant impact on the predicted concentrations.

Implications: The paper provides emission factors (EFs) that are a function of traffic volume and mode of operation (free flow and congestion) for LDVs under real-world conditions. The good agreement between monitoring and modeling results indicates that high-resolution, simultaneous measurements of air quality and meteorological and traffic conditions can be used to determine real-world, fleet-wide vehicle EFs as a function of vehicle mode of operation under actual driving conditions.     

Considerations in Setting Standards for Oxides of Nitrogen

Since 1959 the California Department of Public Health has held responsibility for setting standards for ambient air quality and for motor vehicle emissions. The need for standards for oxides of nitrogen involves consideration both of direct effects and effects resulting from participation in photochemical smog reactions. This paper discusses the various effects of concern and describes the department’s program for establishing air quality standards which will become the basis for vehicle emission standards and serve as guides for control of other sources of oxides of nitrogen.     

Urban CO Concentrations and Vehicle Emissions

The effect of the general growth of CO vehicular emissions in urban areas on the CAMP station measurements in downtown areas, where vehicular traffic is saturated is considered. With the assumption that the street-level CO concentration is derived from the sum of an urban background term and a local street-effect term, the urban background CO concentration is computed with a diffusion model by introducing a simple area source distribution. The local street-effect term is taken to be constant at a saturation emission level corresponding to a saturation traffic density when the emission per vehicle-mile and meteorological conditions are fixed. The present analysis indicates that the local street-effect term, AC, has a major role in determining street-level concentrations for pollutants, such as CO, whose air quality standard is based on maximum concentrations with averaging times of 1 hour and 8 hours. The relevance of this analysis to the abatement requirements of the Clean Air Amendments and to the driving cycle adopted is discussed.     

The state of ambient air quality in Pakistan—a review

Background and purpose  

Pakistan, during the last decade, has seen an extensive escalation in population growth, urbanization, and industrialization, together with a great increase in motorization and energy use. As a result, a substantial rise has taken place in the types and number of emission sources of various air pollutants. However, due to the lack of air quality management capabilities, the country is suffering from deterioration of air quality. Evidence from various governmental organizations and international bodies has indicated that air pollution is a significant risk to the environment, quality of life, and health of the population. The Government has taken positive steps toward air quality management in the form of the Pakistan Clean Air Program and has recently established a small number of continuous monitoring stations. However, ambient air quality standards have not yet been established. This paper reviews the data being available on the criteria air pollutants: particulate matter (PM), sulfur dioxide, ozone, carbon monoxide, nitrogen dioxide, and lead.     

Carbon monoxide modeling from transportation sources.

Street canyon module and gaussian line source module of a regional-scale dispersion model Indic Airviro were used to simulate ambient carbon monoxide (CO) concentrations due to traffic flow at two roadside monitoring locations in Singapore. The fleet average emission factors for each vehicle category was estimated from US EPA MOBILE 5 A guidelines as a function of speed, vehicle deterioration rates and model years. 1-h CO concentrations and worst case 8-h levels have been simulated and compared with measured readings. This study used model-simulated rooftop concentration levels from non-localized sources as background levels at the two sites. The resulting CO concentrations correlate well with actual measured levels and provide a unique approach to predict the impact of CO from transportation.     

A Survey Technique for Determining The Representativeness of Urban Air Monitoring Stations With Respect to Carbon Monoxide

An air quality survey technique for measuring the horizontal spatial variation of carbon monoxide concentrations in urban areas is described; it was used to determine how representative an urban air monitoring station is of concentrations throughout the city.

The survey technique was applied in San Jose, Calif., where 1128 samples were collected over a six-month period and were compared with the values recorded simultaneously at the urban air monitoring station. All samples were collected at “breathing height” within a 13-square-mile grid which included the downtown area as well as surrounding residential and industrial locations. Three basic sampling strategies were employed to answer specific questions about the distribution of carbon monoxide concentration: (7) walking sampling, in which samples were obtained while walking along the sidewalks of congested downtown streets, (2) random spatial sampling, in which samples were collected at randomly selected points in the urban grid, and (3) specialized sampling in the immediate vicinity of the air monitoring station.

The results indicate that pedestrians on downtown streets in San Jose can be exposed to concentrations above the federal air quality standards without these values being observed at the air monitoring station. There also is evidence that, at any instant of time, similar values of carbon monoxide exist throughout this city (within a 13-square mile area), provided that measurements are not made in close proximity to streets. Furthermore, the higher concentrations observed in the immediate vicinity of streets decrease quite rapidly with increasing horizontal distance from these streets.

These findings, in the view of the authors, raise serious doubts as to whether it is possible to determine if air quality standards as currently defined are actually being met in urban areas using data from present-day air monitoring stations.     

Methods of characterizing the distribution of exhaust emissions from light-duty, gasoline-powered motor vehicles in the U.S. fleet

Mobile sources significantly contribute to ambient concentrations of airborne particulate matter (PM). Source apportionment studies for PM10 (PM < or = 10 microm in aerodynamic diameter) and PM2.5 (PM < or = 2.5 microm in aerodynamic diameter) indicate that mobile sources can be responsible for over half of the ambient PM measured in an urban area. Recent source apportionment studies attempted to differentiate between contributions from gasoline and diesel motor vehicle combustion. Several source apportionment studies conducted in the United States suggested that gasoline combustion from mobile sources contributed more to ambient PM than diesel combustion. However, existing emission inventories for the United States indicated that diesels contribute more than gasoline vehicles to ambient PM concentrations. A comprehensive testing program was initiated in the Kansas City metropolitan area to measure PM emissions in the light-duty, gasoline-powered, on-road mobile source fleet to provide data for PM inventory and emissions modeling. The vehicle recruitment design produced a sample that could represent the regional fleet, and by extension, the national fleet. All vehicles were recruited from a stratified sample on the basis of vehicle class (car, truck) and model-year group. The pool of available vehicles was drawn primarily from a sample of vehicle owners designed to represent the selected demographic and geographic characteristics of the Kansas City population. Emissions testing utilized a portable, light-duty chassis dynamometer with vehicles tested using the LA-92 driving cycle, on-board emissions measurement systems, and remote sensing devices. Particulate mass emissions were the focus of the study, with continuous and integrated samples collected. In addition, sample analyses included criteria gases (carbon monoxide, carbon dioxide, nitric oxide/nitrogen dioxide, hydrocarbons), air toxics (speciated volatile organic compounds), and PM constituents (elemental/organic carbon, metals, semi-volatile organic compounds). Results indicated that PM emissions from the in-use fleet varied by up to 3 orders of magnitude, with emissions generally increasing for older model-year vehicles. The study also identified a strong influence of ambient temperature on vehicle PM mass emissions, with rates increasing with decreasing temperatures.     

The Effect of Reformulated Gasoline on Ambient Carbon Monoxide Concentrations in Southeastern Wisconsin

Abstract

Reformulated gasoline (RFG) contains oxygen additives such as methyl tertiary butyl ether or ethanol. The additives enable vehicles to burn fuel with a higher air/fuel ratio, thereby lowering the emission of carbon monoxide (CO) and volatile organic compounds (VOCs). Because VOCs react with sunlight to form ozone (O₃), the Clean Air Act requires severe O₃ nonattainment areas such as southeastern Wisconsin to use RFG. On July 17, 2001, the U.S. Environmental Protection Agency (EPA) granted Milwaukee, WI, and Chicago, IL, a waiver from the VOC reduction requirement of Phase II RFG. The VOC reduction requirement was lowered from 27.4% of the 1990 baseline fuel to 25.4%. The assumption was that ethanol-blended RFG would lower summertime CO concentrations sufficiently to offset the increased VOC emissions. The waiver is estimated to increase VOC emissions by ～0.8%, or 0.4 t of VOC on a hot summer weekday. This study evaluates whether RFG has been effective in lowering southeastern Wisconsin ambient CO concentrations. Three years of ambient CO data before RFG was introduced were compared with the first three years of ambient CO data after RFG was introduced. This paper also evaluates how the meteorology, vehicle inspection/maintenance program, vehicle miles traveled, and stationary source emissions influence CO concentrations. The winter decrease in ambient CO concentrations was found to be statistically significant, while the summer data showed no statistically significant change, indicating that RFG is most effective lowering ambient CO concentrations in cold weather.     

Trends in on-road vehicle emissions and ambient air quality in Atlanta,Georgia, USA,from the late 1990s through 2009

On-road vehicle emissions of carbon monoxide (CO), nitrogen oxides (NO_x), and volatile organic compounds (VOCs) during 1995–2009 in the Atlanta Metropolitan Statistical Area were estimated using the Motor Vehicle Emission Simulator (MOVES) model and data from the National Emissions Inventories and the State of Georgia. Statistically significant downward trends (computed using the nonparametric Theil-Sen method) in annual on-road CO, NO_x, and VOC emissions of 6.1%, 3.3%, and 6.0% per year, respectively, are noted during the 1995–2009 period despite an increase in total vehicle distance traveled. The CO and NO_x emission trends are correlated with statistically significant downward trends in ambient air concentrations of CO and NO_x in Atlanta ranging from 8.0% to 11.8% per year and from 5.8% to 8.7% per year, respectively, during similar time periods. Weather-adjusted summertime ozone concentrations in Atlanta exhibited a statistically significant declining trend of 2.3% per year during 2001–2009. Although this trend coexists with the declining trends in on-road NO_x, VOC, and CO emissions, identifying the cause of the downward trend in ozone is complicated by reductions in multiple precursors from different source sectors.

Implications:Large reductions in on-road vehicle emissions of CO and NO_x in Atlanta from the late 1990s to 2009, despite an increase in total vehicle distance traveled, contributed to a significant improvement in air quality through decreases in ambient air concentrations of CO and NO_x during this time period. Emissions reductions in motor vehicles and other source sectors resulted in these improvements and the observed declining trend in ozone concentrations over the past decade. Although these historical trends cannot be extrapolated to the future because pollutant concentration contributions due to on-road vehicle emissions will likely become an increasingly smaller fraction of the atmospheric total, they provide an indication of the benefits of past control measures.     

The effect of reformulated gasoline on ambient carbon monoxide concentrations in southeastern Wisconsin

Reformulated gasoline (RFG) contains oxygen additives such as methyl tertiary butyl ether or ethanol. The additives enable vehicles to burn fuel with a higher air/fuel ratio, thereby lowering the emission of carbon monoxide (CO) and volatile organic compounds (VOCs). Because VOCs react with sunlight to form ozone (O3), the Clean Air Act requires severe O3 nonattainment areas such as southeastern Wisconsin to use RFG. On July 17, 2001, the U.S. Environmental Protection Agency (EPA) granted Milwaukee, WI, and Chicago, IL, a waiver from the VOC reduction requirement of Phase II RFG. The VOC reduction requirement was lowered from 27.4% of the 1990 baseline fuel to 25.4%. The assumption was that ethanol-blended RFG would lower summertime CO concentrations sufficiently to offset the increased VOC emissions. The waiver is estimated to increase VOC emissions by approximately 0.8%, or 0.4 t of VOC on a hot summer weekday. This study evaluates whether RFG has been effective in lowering southeastern Wisconsin ambient CO concentrations. Three years of ambient CO data before RFG was introduced were compared with the first three years of ambient CO data after RFG was introduced. This paper also evaluates how the meteorology, vehicle inspection/maintenance program, vehicle miles traveled, and stationary source emissions influence CO concentrations. The winter decrease in ambient CO concentrations was found to be statistically significant, while the summer data showed no statistically significant change, indicating that RFG is most effective lowering ambient CO concentrations in cold weather.     

An analysis of effects of San Diego wildfire on ambient air quality

The impact of major gaseous and particulate pollutants emitted by the wildfire of October 2003 on ambient air quality and health of San Diego residents before, during, and after the fire are analyzed using data available from the San Diego County Air Pollution Control District and California Air Resources Board. It was found that fine particulate matter (PM) levels exceeded the federal daily 24-hr average standard during the fire. There was a slight increase in some of the gaseous pollutants, such as carbon monoxide, which exceeded federal standards. Ozone (O3) precursors, such as total hydrocarbons and methane gases, experienced elevated concentration during the fire. Fortunately, the absence of sunlight because of the cloud of thick smoke that covered most of the county during the fire appears to have prevented the photochemical conversion of the precursor gases to harmful concentrations of O3. Statistical analysis of the compiled medical surveillance data has been used to establish correlations between pollutant levels in the region and the resultant health problems experienced by the county citizens. The study shows that the increased PM concentration above the federal standard resulted in a significant increase in hospital emergency room visits for asthma, respiratory problems, eye irritation, and smoke inhalation. On the basis of the findings, it is recommended that hospitals and emergency medical facilities engage in pre-event planning that would ensure a rapid response to an impact on the healthcare system as a result of a large wildfire and appropriate agencies engage in the use of all available meteorological forecasting resources, including real-time satellite imaging assets, to accurately forecast air quality and assist firefighting efforts.