Interactions of Sulfur Dioxide with Insoluble Suspended Particulate Matter

A laboratory study was conducted of the heterogeneous catalysis of sulfur dioxide at ppm concentrations in air by insoluble particles of CaCO₂, V₂O₅, Fe₂0₃, flyash from a coal-burning power plant, MnCO₂, activated carbon, and suspended particulate matter from urban air. The investigalion was performed by utilizing a new technique for aerosol stabilization which consists of depositing the aerosol on Teflon beads in a fluidized bed. The Teflon beads with deposited aerosol particles were then packed into a flow reactor. Progress of the chemical reaction of SO₂ with deposited particles was continuously monitored by determining the SO₂ concentrations in the reactor effluent with a microcoulometer.

In this investigation, CaCOg, V₂O₅, and flyash were essentially inert to SO₂ at room temperature. Fe₂O₃, activated carbon, MnO₂, and suspended particulate matter from urban air sorbed SO₂ from air streams with up to 14.4 ppm SO₂ in air. Evidence is presented which suggests that a substantial part of the sorbed SO₂ was physically adsorbed.

Bioassay procedures which utilize pulmonary flow resistance changes in guinea pigs to monitor response to inhaled SO₂-aerosol mixtures in air have indicated the weak or non-potentiating capacity of insoluble aerosols as contrasted to soluble aerosols. Potentiating response of an aerosol appears to be strongly associated with reaction of SO₂ in a water droplet containing aerosol ions and not with physically adsorbed SO₂ on an insoluble aerosol.     

On the oxidation of SO2 to sulfate in atmospheric aerosols

This paper presents the results of a study to investigate the atmospheric oxidation of sulfur dioxide (SO₂). A detailed model of gas-phase chemistry, aerosol thermodynamics and aerosol chemistry is employed to simulate atmospheric sulfate formation. The calculations indicate that, in addition to the gasphase oxidation by hydroxyl (OH) radicals, SO₂ oxidation in aqueous aerosols may also contribute significantly to sulfate formation. Reactions of SO₂ with hydrogen peroxide (H₂O₂) and O₂ (catalyzed by Fe³⁺ and Mn²⁺) are identified as principal aqueous-phase oxidation mechanisms. The results of this study confirm the conclusions drawn from the analysis of ambient aerosol data qualitatively. However, some discrepancies also exist between the results of our modeling study and field data. Such discrepancies emphasize the need for the collection of ambient data for a more rigorous and quantitative evaluation of atmospheric aerosol models.     

The Survival of Airborne Serratia marcescens in Urban Concentrations of Sulfur Dioxide

Aerosols of Serratia marcescens ATCC 274 were suspended in a 709L rotating drum at 20 ± 1 °C and high to mid-range relative humidities. At specified times after bacterial aerosolization, sulfur dioxide was added to concentrations of 2.5, or 5 mg/m³. Viable cell decay rate constants, in control aerosols without added sulfur dioxide, increased rapidly from near 100% to 60% RH in the first hour (termed: young aerosol) of suspension, and from a minimum rate constant at 80% in the succeeding four hours (termed: old aerosol).Upon addition of sulfur dioxide to a cloud of S. marcescens, generally, viable cell decay rate constants increased further. One exception was at 80% relative humidity where maximum resistance to SO₂ accelerated death was observed for old aerosols. Cells in young aerosols were particularly sensitive to SO₂ addition at mid-range humidities, while in older aerosols the cells were insensitive to up to 5 mg SO₂/m³ introduced at high RH; but were up to 10 times more sensitive than cells in young aerosols to a given increase (from 2.5 to 5 mg/m³) in SO₂ concentration at mid-range humidities.     

Design and characterization of a two-stage human subject exposure chamber

A human subject exposure chamber, designed to hold six to eight subjects, coupled to an approximately 30-m3 Teflon reaction bag was designed and built to provide exposures that mimic the production and photochemical oxidation of atmospheric pollutants resulting from the combustion of coal or wood from a stove. The combustion products are introduced into the Teflon bag under atmospheric conditions. Photochemical oxidation of this mixture is accomplished by exposure to tropospheric sun-like radiation from an array of ultraviolet and black lamps. The aerosol in the Teflon reaction bag is then transferred into the exposure room to maintain a constant, lower exposure level. Continuous and semicontinuous monitoring of the gas and particulate matter (PM) pollution in the exposure room and the reaction bag is accomplished using a suite of instruments. This suite of instruments allows for the measurement of the concentrations of total and nonvolatile PM, nitric oxide, nitrogen dioxide, carbon monoxide, carbon dioxide, and ozone. The concentration of the particles was monitored by an R&P tapered element oscillating microbalance monitor. The chemical composition of the PM and its morphological characterization is accomplished by collecting samples in filter packs and conducting ion chromatography, elemental X-ray fluorescence, and scanning electron microscopy analyses. The concentration and composition of emissions from combustion of wood and coal is described. The results of this study suggest that although the bulk compositions of particulate emissions from the combustion of coal or wood in a stove have many similarities, the wood smoke aerosol is photochemically reactive, whereas the coal smoke aerosol is not.     

The effect of water on gas–particle partitioning of secondary organic aerosol. Part I: α-pinene/ozone system

The effect of relative humidity (RH) on aerosol formation by the semi-volatile oxidation products of the α-pinene/O₃ system has been comprehensively studied. Experiments were performed in the presence of ammonium sulfate (aqueous, dry), ammonium bisulfate seed (aqueous, dry), and aqueous calcium chloride seed aerosols to ascertain their effect on the partitioning of the oxidation products. The yield of organic aerosol varies little with RH, and is not affected by the presence of dry inorganic salt aerosols. Aqueous salt aerosols reduce the yield of organic aerosol compared to that under seed-free or dry seed conditions. The degree of reduction is electrolyte dependent, with aqueous ammonium sulfate leading to the largest reduction and aqueous calcium chloride the smallest. Hygroscopic growth of the organic aerosol from <2% to 85% RH was also monitored, and could be satisfactorily represented as the sum of the individual contributions of the organic and inorganic fractions. The implications of the growth factor measurements for concentration/activity relationships of the condensed phase organic material (assuming a liquid solution) was explored. The formation of the organic aerosol was investigated using a simple two component model, and also one including the 12 product compounds identified in a previous study. The experimental results for <2% and 50% RH (without salt seed aerosols) could be satisfactorily predicted. However, the aqueous salt seed aerosols are predicted to increase the overall yield due to the dissolution of the organic compounds into the water associated with the seed aerosol—the opposite effect to that observed. The implications of two distinct phases existing the aerosol phase were investigated.     

Continued development of a general equilibrium model for inorganic multicomponent atmospheric aerosols

A model is presented that predicts the total quantities of ammonium, chloride, nitrate and water contained in atmospheric aerosols, their physical state and their distribution among aerosol particles of different sizes. The model is based on the thermodynamic equilibrium calculation of the ammonium/chloride/nitrate/sodium/sulfate/water system. The existence of water in the aerosol phase at low relative humidities is shown to be explained. Observed aerosol concentrations at Long Beach, California during 30–31 August 1982 are successfully predicted.     

Observation based analysis for the determination of equilibrium time constant between ammonia, acid gases, and fine particles

Experimental measurements of ammonia, acid gases, and the inorganic components of atmospheric aerosols were made at a commercial hog farm in eastern North Carolina from May 1998 to June 1999 by an annular denuder system (ADS). The ADS consisted of a cyclone separator, one diffusion denuder coated with sodium carbonate, another diffusion denuder with citric acid, and a filter pack containing Teflon and nylon filters in series. The equilibrium time constant for transfer between ammonia, acid gases, and aerosol phase of ammonium nitrate and ammonium chloride was determined based on kinetic rate constants (k_N as the rate constant of ammonium nitrate aerosol: 2.04 × 10^-4 m³/µmole/sec; k_Cl as the rate constant of ammonium chloride aerosol: 3.44 × 10^-4 m³/µmole/sec) and the observed inorganic components of atmospheric aerosols. The equilibrium time constant was determined based on kinetic rate constants and the observed inorganic components of atmospheric aerosols. The equilibrium time constant has a wide range of values, with an average value of 15.26 (±10.94) minutes for ambient equilibrium time between ammonia, nitric acid gas and ammonium nitrate aerosol; and 8.22 (±6.81) minutes for ammonia, hydrochloric acid, and ammonium chloride. Significant correlations were determined between comparisons of equilibrium time constant estimates with meteorological parameters, such as ambient temperature and relative humidity. The predicted chemical compositions in the particle by EQUISOLV II Model are in good agreement with the observed chemical composition at the experimental site.     

Sulfur processing in the marine atmospheric boundary layer: A review and critical assessment of modeling uncertainties

Sulfur is an extremely motile and vital element in the Earth's biogeochemical environment, one whose active redox chemistry maintains small reservoirs in the atmosphere and biosphere yet large fluxes through both. Essential for life, intimately linked to the climate state, and an important component of air quality, sulfur and its transport and processing in the atmosphere have been the subject of active research for several decades. This review article describes the current state of our understanding of the atmospheric sulfur cycle, focusing on the marine atmospheric boundary layer, with the aim of identifying the largest roots of uncertainty that most inhibit accurate simulation of sulfur cycling in the atmosphere. An overview of the emissions by phytoplankton and shipping, dispersion and entrainment in the marine boundary layer, and chemical processing by aerosols, clouds, and dry deposition is presented. Analysis of 20 contemporary modeling studies suggests that the greatest ambiguity in global sulfur cycling derives from (in descending order) wet deposition of aerosol sulfate, dry deposition of sulfur dioxide to the Earth's surface, and the heterogeneous oxidation of SO₂ in aerosols and clouds.     

Integrated chemical species analysis with source-receptor modeling results to characterize the effects of terrain and monsoon on ambient aerosols in a basin

This study integrated estimated oxidation ratio of sulfur (SOR) and oxidation ratio of nitrogen (NOR) with source-receptor modeling results to identify the effects of terrain and monsoons on ambient aerosols in an urban area (north basin) and a rural area (south basin) of the Taichung Basin. The estimated results indicate that the conversion of sulfur mainly occurs in fine particles (PM_2.5), whereas the conversion of nitrogen occurs in approximately equal quantities of PM_2.5 and coarse particles (PM_2.5–10). The results show a direct relationship for PM_2.5 between the modeling results with SOR and NOR. The high PM_2.5 SOR, NOR, and secondary aerosol values all occurred in the upwind area during both monsoons; this shows that the photochemical reaction and the terrain effect on the pollutant transmission were significant in the basin. Additionally, the urban heat island effect on the urban area and the valley effect on the rural area were significant. The results show that secondary aerosol in PM_2.5–10 contributed approximately 10 % during both monsoons, and the difference in the contribution from secondary aerosol between both areas was small. Vehicle exhaust emissions and wind-borne dust were two crucial PM_2.5–10 contributors during both monsoons; their average contributions in both areas were higher than 34 and 32 %, respectively.     

Influence of NO2 on S(IV) oxidation in aqueous suspensions of aerosol particles from two different origins

The influence of soluble compounds leached from real atmospheric aerosol particles (size range D_ae: 0.17–1.6 μm) and dissolved NO₂ on S(IV) oxidation in aqueous solution is presented. Experiments were conducted with aerosol particles of two different origins (i.e., urban and industrial) and at concentrations of trace gases in the gas mixtures (SO₂/air and SO₂/NO₂/air) typical for a polluted atmosphere. During the introduction of SO₂/air into the aqueous aerosol suspensions under dark conditions at pH 4, the formation of SO₄²⁻ was very slow with a long induction period. However, in the presence of NO₂ the oxidation rate of dissolved SO₂ in suspensions of aerosols from both origins increased substantially (about 10 times). The results suggest that soluble compounds eluted from atmospheric aerosols have not only a catalytic (e.g. Fe, Mn), but also a pronounced inhibiting effect (e.g., oxalate, formate, acetate, glycolate) on S(IV) autoxidation. When NO₂ was also introduced into the aerosol suspensions, the inhibition was not so highly expressed. An explanation for this is that the radical chain mechanism is mainly initiated by the interaction of dissolved NO₂ and HSO₃⁻. Therefore, at conditions typical for a polluted atmosphere dissolved NO₂ can have a significant influence on the secondary formation of SO₄²⁻.     

A 2-D model of global aerosol transport

The distribution of aerosol particles in the troposphere is described. Starting with long term mean seasonal flow and diffusivities as well as temperature, cloud distribution (six cloud classes), relative humidity and OH radical concentration, the steady state concentration of aerosol particles and SO₂ are calculated in a two-dimensional global (height and latitude) model. The following sources and sinks for particles are handled: direct emission, gas-to-particle conversion from SO₂, coagulation, rainout, washout, gravitational settling, and dry deposition. The sinks considered for sulphur emissions are dry deposition, washout, rainout, gasphase oxidation, and aqueous phase oxidation. Model tests with the water vapour cycle show a good agreement between measured and calculated zonal mean precipitation distribution.The steady state concentration distribution for natural emissions reached after 10 weeks model time, may be described by a mean exponent α = 3.2 near the surface assuming a modified Junge distribution and an increased value, α = 3.7, for the combined natural and man-made emission. The maximum ground level concentrations are 2000 and 10,000 particles cm⁻³ for natural and natural plus man-made emissions, respectively. The resulting distribution of sulphur dioxide agrees satisfactorily with measurements given by several authors.     

Application of Gas-Aerosol Adsorption Data to the Selection of Air Quality Standards

A quantitative approach is presented for selecting air quality standards which take into account pollutant gas-aerosol synergistic effects. These synergistic health effects have been postulated to be due to the adsorption or absorption of the pollutant gas by the aerosol particles. The approach presented in this paper assumes that the synergistic toxic agent is the adsorbed pollutant gas. Therefore, limiting the concentration of the adsorbed pollutant gas limits the magnitude of the synergistic effects. The concentration of the adsorbed pollutant gas is related to the concentrations of the gaseous phase pollutant gas and the atmospheric aerosol using the Langmuir adsorption isotherm. An example is presented of the selection of air quality standards for sulfur dioxide and the atmospheric aerosol using concentration data for these two pollutants along with health effect data.     

The contribution of aircraft emissions to the atmospheric sulfur budget

An atmospheric general circulation model including the atmospheric sulfur cycle has been used to investigate the impact of aircraft sulfur emissions on the global sulfur budget of the atmosphere. The relative contribution from aircraft sulfur to the atmospheric sulfate burden is larger than the ratio between aircraft emissions and surface emissions due to the calculated long turn-over time of aircraft sulfate (about 12 days). However, in terms of the sulfate mass balance, aircraft emissions are small, contributing about 1% of the total sulfate mass north of 40°N where the aircraft emissions are largest. Despite this small contribution to sulfate mass, the aircraft emissions could potentially significantly enhance the background number concentration of aerosol particles. Based on the model calculations the increased stratospheric background aerosol mass observed during the last decades cannot be explained by increased aircraft sulfur emissions.     

Phase transition behaviour of sodium oleate aerosol particles

Field measurements have shown that organic surfactants are significant components of atmospheric aerosols. While fatty acids, among other surfactants, are prevalent in the atmosphere, the influence of these species on the chemical and physical properties of atmospheric aerosols remains not fully characterized. In order to assess the phase in which particles may exist, a detailed study of the deliquescence of a model surfactant aerosol has been carried out. Sodium oleate was chosen as a surfactant proxy relevant in atmospheric aerosol. Sodium oleate micelle aerosol particles were generated nebulizing a sodium oleate aqueous solution. In this study, the water uptake and phase transition of sodium oleate aerosol particles have been studied in a room temperature aerosol flow tube system (AFT) using Fourier transform infrared (FTIR) spectroscopy. Aerosol morphology and elemental composition were also analysed using scanning electron microscopy/energy dispersive X-ray analysis (SEM/EDX) techniques. The particles are homogeneously distributed as ellipsoidal-shape aggregates of micelles particles with an average size of ∼1.1 μm. The deliquescence by the sodium oleate aerosol particles was monitored by infrared extinction spectroscopy, where the dried aerosol particles were exposed to increasing relative humidity as they passed through the AFT. Observations of the infrared absorption features of condensed phase liquid water enable to determine the sodium oleate deliquescence phase transition at 88±2%.     

Size-differentiated composition of inorganic atmospheric aerosols of both marine and polluted continental origin

Atmospheric aerosols were sampled with a high volume impactor/diffusion battery system and the collected fractions analysed for their major water-soluble inorganic constituents. Sulphate, nitrate and chloride showed bimodal distributions; sulphate and nitrate were mainly associated with NH₄⁺, having approximately log-normal distributions with modes at 1.0 μm. In unpolluted maritime air, chlorides appeared as salts of sodium and magnesium with average modes at c. 5 μm, whilst in polluted air masses significant concentrations of ammonium chloride sub-μm aerosols were detected. Sodium nitrate and sodium sulphate aerosols having average modes of c. 3.5 μm were observed in mixed maritime/polluted air masses. The dimensions of these particles indicate formation from absorption of H₂SO₄ and HNO₃ at the surface of marine NaCl particles. The concentration of H⁺ was very low, but the possibility of its neutralization by atmospheric ammonia during sampling was ruled out by parallel air sampling using an ‘ammonia denuder’.     

Quantification and radiocarbon source apportionment of black carbon in atmospheric aerosols using the CTO-375 method

To make progress towards linking the atmosphere and biogeosphere parts of the black carbon (BC) cycle, a chemothermal oxidation method (CTO-375), commonly applied for isolating BC from complex geomatrices such as soils, sediments and aquatic particles, was applied to investigate the BC also in atmospheric particles. Concentrations and ¹⁴C-based source apportionment of CTO-375 based BC was established for a reference aerosol (NIST RM-8785) and for wintertime aerosols collected in Stockholm and in a Swedish background area. The results were compared with thermal–optical (OC/EC) measurements. For NIST RM-8785, a good agreement was found between the BC_CTO-375 concentration and the reported elemental carbon (EC) concentration measured by the “Speciation Trends Network—National Institute of Occupational Safety and Health” method (EC_NIOSH) with BC_CTO-375 of 0.054±0.002 g g⁻¹ and EC_NIOSH of 0.067±0.008 g g⁻¹. In contrast, there was an average factor of ca. 20 difference between BC_CTO-375 and EC_NIOSH for the ambient Scandinavian wintertime aerosols, presumably reflecting a combination of BC_CTO-375 isolating only the recalcitrant soot-BC portion of the BC continuum and the EC_NIOSH metric inadvertently including some intrinsically non-pyrogenic organic matter. Isolation of BC_CTO-375 with subsequent off-line radiocarbon analysis yielded fraction modern values (fM) for total organic carbon (TOC) of 0.93 (aerosols from a Swedish background area), and 0.58 (aerosols collected in Stockholm); whereas the fM for BC_CTO-375 isolates were 1.08 (aerosols from a Swedish background area), and 0.87 (aerosols collected in Stockholm). This radiocarbon-based source apportionment suggests that contribution from biomass combustion to cold-season atmospheric BC_CTO-375 in Stockholm was 70% and in the background area 88%.     

Uncertainty Requirements in Radiative Forcing of Climate Change

Abstract

The continuing increase in atmospheric carbon dioxide (CO₂) makes it essential that climate sensitivity, the equilibrium change in global mean surface temperature that would result from a given radiative forcing, be quantified with known uncertainty. Present estimates are quite uncertain, 3 ± 1.5 K for doubling of CO₂. Model studies examining climate response to forcing by greenhouse gases and aerosols exhibit large differences in sensitivities and imposed aerosol forcings that raise questions regarding claims of their having reproduced observed large-scale changes in surface temperature over the 20th century. Present uncertainty in forcing, caused largely by uncertainty in forcing by aerosols, precludes meaningful model evaluation by comparison with observed global temperature change or empirical determination of climate sensitivity. Uncertainty in aerosol forcing must be reduced at least three-fold for uncertaintyin climate sensitivity to be meaningfully reduced and bounded.     

Seasonal Variations in Aerosol Composition and Acidity at Shenandoah and Great Smoky Mountains National Parks

The concentration of elements Na through Pb, select ions, and organic carbon from fine (<2.5 µm) particles has been monitored at Shenandoah and Great Smoky Mountains National Parks from 1988 through 1995. The data obtained from 1988 through 1994 show that significant changes in the concentrations of many aerosol constituents occur on a seasonal basis. Particulate sulfate and organic carbon are shown to exhibit substantially higher concentrations during the summer, while sulfur dioxide and nitrate concentrations are highest during the winter.

A method for estimating the degree of neutralization of particulate sulfate is given. This method uses routinely measured aerosol elemental compositions because ammonium ion, the primary neutralizing species for sulfate, is not measured on a routine basis. Application of this method to the selected data set shows that sulfate aerosol is most acidic during summer with an average molar H_s (moles of hydrogen associated with sulfur) to S (moles of sulfur) ratio of approximately 4. This suggests the average sulfate particle during the summer has a molar coon slightly more acidic than ammonium bisulfate (NH₄HSO₄) which has a molar hydrogen to sulfur ratio of 5. Winter H_s to S ratios, however, are approximately 8, suggesting the aerosol is on average fully neutralized ammonium sulfate [(NH₄)₂SO₄].     

Monitoring of sources and atmospheric processes controlling air quality in an urban Mediterranean environment

Different monitoring parameters (PM mass concentrations, number–size distribution, black carbon, gaseous pollutants, and chemical composition, among others) are currently used in air quality studies. Urban aerosols are the result of several sources and atmospheric processes, which suggests that a single monitoring technique is insufficient to quantitatively evaluate all of them.This study assesses the suitability of a number of monitoring techniques (PM mass concentrations, number and size distribution of ultra-fine particles, levels of gaseous pollutants, and a complete chemical characterization of PM₁₀ and PM_2.5) by examining the response of those techniques to the different emission sources and/or atmospheric processes affecting an urban Mediterranean area (Barcelona, NE Spain).The results of this work reveal that the PM mass, the number concentration and the chemical composition give different, but complementary, information. Whereas the mineral matter, a key atmospheric aerosol component across the Mediterranean, is not properly quantitatively assessed by measuring sub-micrometric particles, the monitoring of the number concentration is indispensable to interpret the origin of specific aerosol episodes. Furthermore, the chemical composition yields very relevant information to deduce the causes of specific pollution episodes.The number concentration of ultra-fine particles in urban areas is strongly dependent upon vehicle exhaust emissions, which may cause adverse health impacts. Moreover, urban Mediterranean environments are favourable to produce nucleation-mode particles (<20 nm) with photochemical origin. In those cases, these particles are expected to be of high solubility and consequently their toxicity may differ from that of traffic-generated ultra-fine particles. Thus, the use of a single monitoring parameter to evaluate the health effects seems to be not enough.