Multispecies remote sensing measurements of vehicle emissions on Sherman Way in Van Nuys,California

As part of the 2010 Van Nuys tunnel study, researchers from the University of Denver measured on-road fuel-specific light-duty vehicle emissions from nearly 13,000 vehicles on Sherman Way (0.4 miles west of the tunnel) in Van Nuys, California, with its multispecies Fuel Efficiency Automobile Test (FEAT) remote sensor a week ahead of the tunnel measurements. The remote sensing mean gram per kilogram carbon monoxide (CO), hydrocarbon (HC), and oxide of nitrogen (NO_x) measurements are 8.9% lower, 41% higher, and 24% higher than the tunnel measurements, respectively. The remote sensing CO/NO_x and HC/NO_x mass ratios are 28% lower and 20% higher than the comparable tunnel ratios. Comparisons with the historical tunnel measurements show large reductions in CO, HC, and NO_x over the past 23 yr, but little change in the HC/NO_x mass ratio since 1995. The fleet CO and HC emissions are increasingly dominated by a few gross emitters, with more than a third of the total emissions being contributed by less than 1% of the fleet. An example of this is a 1995 vehicle measured three times with an average HC emission of 419 g/kg fuel (two-stroke snowmobiles average 475 g/kg fuel), responsible for 4% of the total HC emissions. The 2008 economic downturn dramatically reduced the number of new vehicles entering the fleet, leading to an age increase (>1 model year) of the Sherman Way fleet that has increased the fleet's ammonia (NH₃) emissions. The mean NH₃ levels appear little changed from previous measurements collected in the Van Nuys tunnel in 1993. Comparisons between weekday and weekend data show few fleet differences, although the fraction of light-duty diesel vehicles decreased from the weekday (1.7%) to Saturday (1.2%) and Sunday (0.6%).

Implications: On-road remote sensing emission measurements of light-duty vehicles on Sherman Way in Van Nuys, California, show large historical emission reductions for CO and HC emissions despite an older fleet arising from the 2008 economic downturn. Fleet CO and HC emissions are increasingly dominated by a few gross emitters, with a single 1995 vehicle measured being responsible for 4% of the entire fleet's HC emissions. Finding and repairing and/or scrapping as little as 2% of the fleet would reduce on-road tailpipe emissions by as much as 50%. Ammonia emissions have locally increased with the increasing fleet age.     

On-Road,In-Use Gaseous Emission Measurements by Remote Sensing of School Buses Equipped with Diesel Oxidation Catalysts and Diesel Particulate Filters

Abstract

A remote sensing device was used to obtain on-road and in-use gaseous emission measurements from three fleets of schools buses at two locations in Washington State. This paper reports each fleet’s carbon monoxide (CO), hydrocarbon (HC), nitric oxide (NO), and nitrogen dioxide (NO₂) mean data. The fleets represent current emission retrofit technologies, such as diesel particulate filters and diesel oxidation catalysts, and a control fleet. This study shows that CO and HC emissions decrease with the use of either retrofit technology when compared with control buses of the same initial emission standards. The CO and HC emission reductions are consistent with published U.S. Environmental Protection Agency verified values. The total oxides of nitrogen (NO_x), NO, and the NO₂/NO_x ratio all increase with each retrofit technology when compared with control buses. As was expected, the diesel particulate filters emitted significantly higher levels of NO₂ than the control fleet because of the intentional conversion of NO to NO₂ by these systems. Most prior research suggests that NO_x emissions are unaffected by the retrofits; however, these previous studies have not included measurements from retrofit devices on-road and after nearly 5 yr of use. Two 2006 model-year buses were also measured. These vehicles did not have retrofit devices but were built to more stringent new engine standards. Reductions in HCs and NO_x were observed for these 2006 vehicles in comparison to other non-retrofit earlier model-year vehicles.     

Prospects of inspection and maintenance of two-wheelers in India.

Two-wheeler vehicles in Delhi, India--roughly 70% of the total vehicle fleet--are responsible for a significant portion of the city's vehicle emissions and petroleum consumption. An inspection and maintenance (I/M) program that ensures vehicle emission control systems are well maintained can complement other emission reduction strategies. This paper presents the initial findings of extensive data collected on vehicle characteristics and emissions for two-wheeler vehicles operating in Delhi in a series of I/M camps conducted by the Society of Indian Automobile Manufacturers and various partners in late 1999. The analysis shows idle HC and CO emissions [measured in terms of parts per million (ppm) and volume % (vol %), respectively] in a slow declining trend with subsequent model years, reflecting tighter emission standards and more advanced emission technologies. The I/M benefits--3 vol % and 39% reduction in idle and mass CO, respectively; 40 vol % and 22% reduction in idle and mass HC, respectively; and a 10-20% increase in fuel efficiency--were higher than those reported in the literature. Although these benefits are substantial, any implementation strategy needs to consider cost-effectiveness. In the present study, only 10% of vehicles--contributing 22% of the total vehicle emissions--failed the idle CO standard. Fleet emissions data variability necessitates a large sample size to develop a baseline for the vehicle fleet, but a smaller, scientifically designed sample and better data collection quality could periodically track the benefits at future camps.     

Diagnosis and Repair of Excessively Emitting Vehicles

Abstract

Between 1991 and 1993, the California Air Resources Board (CARB) selected 1,115 vehicles from all across the South Coast Air Basin to evaluate the effectiveness of the state's existing biennial motor vehicle Inspection/Maintenance (I/M) or Smog Check program. The vehicles were chosen to represent the population of cars that "should fail" properly conducted inspections. The cars were emissions-tested at baseline and sent undercover to licensed I/M garages throughout the basin. Federal Test Procedure (FIT) emissions were measured again for cars that were repaired. In the second year of the study, the vehicles that could be reproduced were tested at the CARB to measure the level of emissions deterioration and any underhood changes in emission control systems. In the third year, the cycle of emissions testing and undercover inspections and repair was repeated.

This paper uses data from the study to explore the relationships between super emitting vehicles (defined here as vehicles whose emissions are several times California certification standards) and diagnostics and repair of their underhood emissions control systems. Also examined is their appearance and improvement during a three-year period that includes two cycles of inspection and repair. An important finding is that once normalized to account for differences in certification standards, the super emitting vehicles do not have a unique signature in terms of their underhood emission control system failure modes, mileage, or age, when compared with the average vehicle expected to fail a Smog Check inspection. However, they are more likely to be identified, diagnosed, and repaired effectively than other vehicles, although they continue to reappear over time.     

An Investigation of Idle Emissions Inspection and Maintenance at Altitude

Idle emissions inspection and maintenance was evaluated using a sample of 300 privately owned 1964 through 1973 model-year vehicles operating in the Denver metropolitan area. Ten privately owned stations, licensed by the State of Colorado to perform vehicle safety inspections, were utilized to conduct idle emissions inspection and subsequent maintenance of failed vehicles. Exhaust hydrocarbon (HC) and carbon monoxide (CO) reduction as measured by the 1975 Environmental Protection Agency (EPA) mass emission testing procedures was indicated to be 13% and 8% respectively at a 50 % rejection rate. The average maintenance cost to achieve the reduction was $11.32 per failed vehicle.

The adjustment and repair procedures provided to participating garages were sufficient to achieve significant emissions reduction and training provided to garage personnel was adequate. However, several problems were experienced with station personnel relative to data transmittal and inspection pass/fail limits. Problems were also experienced with respect to correlations between laboratory and garage-type analytical instrumentation.     

On-road remote sensing measurements and fuel-based motor vehicle emission inventory in Hangzhou,China

Motor vehicles are one of the largest sources of air pollutants worldwide. Despite their importance, motor vehicle emissions are inadequately understood and quantified, esp. in developing countries. In this study, the real-world emissions of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxide (NO) were measured using an on-road remote sensing system at five sites in Hangzhou, China in 2004 and 2005. Average emission factors of CO, HC and NO_x for petrol vehicles of different model year, technology class and vehicle type were calculated in grams of pollutant per unit of fuel use (g l⁻¹) from approximately 32,260 petrol vehicles. Because the availability of data used in traditional on-road mobile source estimation methodologies is limited in China, fuel-based approach was implemented to estimate motor vehicle emissions using fuel sales as a measure of vehicle activity, and exhaust emissions factors from remote sensing measurements. The fuel-based exhaust emission inventories were also compared with the results from the recent international vehicle emission (IVE) model. Results show that petrol vehicle fleet in Hangzhou has significantly high CO emissions, relatively high HC and low NO_x, with the average emission factors of 193.07±15.63, 9.51±2.40 and 5.53±0.48 g l⁻¹, respectively. For year 2005 petrol vehicles exhaust emissions contributed with 182,013±16,936, 9107±2255 and 5050±480 metric ton yr⁻¹ of CO, HC and NO_x, respectively. The inventories are 45.5% higher, 6.6% higher and 53.7% lower for CO, HC and NO_x, respectively, than the estimates using IVE travel-based model. In addition, a number of insights about the emission distributions and formation mechanisms have been obtained from an in-depth analysis of these results.     

Idle Emissions from Heavy-Duty Diesel and Natural Gas Vehicles at High Altitude

ABSTRACT

Idle emissions of total hydrocarbon (THC), CO, NO_x, and particulate matter (PM) were measured from 24 heavy-duty diesel-fueled (12 trucks and 12 buses) and 4 heavy-duty compressed natural gas (CNG)-fueled vehicles. The volatile organic fraction (VOF) of PM and aldehyde emissions were also measured for many of the diesel vehicles. Experiments were conducted at 1609 m above sea level using a full exhaust flow dilution tunnel method identical to that used for heavy-duty engine Federal Test Procedure (FTP) testing. Diesel trucks averaged 0.170 g/min THC, 1.183 g/min CO, 1.416 g/min NO_x, and 0.030 g/min PM. Diesel buses averaged 0.137 g/min THC, 1.326 g/min CO, 2.015 g/min NO_x, and 0.048 g/min PM.

Results are compared to idle emission factors from the MOBILE5 and PART5 inventory models. The models significantly (45-75%) overestimate emissions of THC and CO in comparison with results measured from the fleet of vehicles examined in this study. Measured NO_x emissions were significantly higher (30-100%) than model predictions. For the pre-1999 (pre-consent decree) truck engines examined in this study, idle NO_x emissions increased with Health and Environment; June 30, 1999 (available from the authors).     

Emission Factors for High-Emitting Vehicles Based on On-Road Measurements of Individual Vehicle Exhaust with a Mobile Measurement Platform

ABSTRACT

Fuel-based emission factors for 143 light-duty gasoline vehicles (LDGVs) and 93 heavy-duty diesel trucks (HDDTs) were measured in Wilmington, CA using a zero-emission mobile measurement platform (MMP). The frequency distributions of emission factors of carbon monoxide (CO), nitrogen oxides (NO_x), and particle mass with aerodynamic diameter below 2.5 μm (PM_2.5) varied widely, whereas the average of the individual vehicle emission factors were comparable to those reported in previous tunnel and remote sensing studies as well as the predictions by Emission Factors (EMFAC) 2007 mobile source emission model for Los Angeles County. Variation in emissions due to different driving modes (idle, low- and high-speed acceleration, low- and high-speed cruise) was found to be relatively small in comparison to intervehicle variability and did not appear to interfere with the identification of high emitters, defined as the vehicles whose emissions were more than 5 times the fleet-average values. Using this definition, approximately 5% of the LDGVs and HDDTs measured were high emitters. Among the 143 LDGVs, the average emission factors of NO_x, black carbon (BC), PM_2.5, and ultrafine particle (UFP) would be reduced by 34%, 39%, 44%, and 31%, respectively, by removing the highest 5% of emitting vehicles, whereas CO emission factor would be reduced by 50%. The emission distributions of the 93 HDDTs measured were even more skewed: approximately half of the NO_x and CO fleet-average emission factors and more than 60% of PM_2.5, UFP, and BC fleet-average emission factors would be reduced by eliminating the highest-emitting 5% HDDTs. Furthermore, high emissions of BC, PM_2.5, and NO_x tended to cluster among the same vehicles.

IMPLICATIONS This study presents the characterization of on-road vehicle emissions in Wilmington, CA, by sampling individual vehicle plumes. Approximately 5% of the vehicles were high emitters, whose emissions were more than 5 times the fleet-average values. These high emitters were responsible for 30% and more than 50% of the average emission factors of LDGVs and HDDVs, respectively. It is likely that as the overall fleet becomes cleaner due to more stringent regulations, a small fraction of the fleet may contribute a growing and disproportionate share of the overall emissions. Therefore, long-term changes in on-road emissions need to be monitored.     

New Jersey Repair Project: Tune-Up at Idle

Idle hydrocarbon and carbon monoxide measurements have been made on over 2500 cars at a New Jersey Inspection Station. These studies have shown that the idle test can be integrated into the present periodic motor vehicle inspection system with a minimum cost, testing time, and ease of operation.

Instrumentation at a low cost has recently become available, test procedures have been developed and potential emission reductions have been demonstrated for idle testing. High emissions indicate a car malfunction and the need for a tune-up. Effective low cost tune-ups can be made with exhaust instrumentation and garage training.

In the New Jersey REPAIR Project, preliminary idle cut-off levels were selected at 6% carbon monoxide and 1000 ppm hydrocarbon for pre-68 cars, 4% and 500 ppm for 1968–69 cars, and 3% and 300 ppm for later years. Volunteered vehicles which exceeded these levels were further tested at the New Jersey laboratory. Federal hot cycles, ACID mass cycles, Key Mode, and Idle tests were conducted before and after maintenance.

At idle, uncontrolled pre-1968 vehicles had an average reduction from 8.2 to 3.3% carbon monoxide and 2153 to 459 ppm hydrocarbons as hexane. Average mass reductions from the ACID-cycle were 45 g/mi CO and 6.3 g/mi hydrocarbons. Carbon monoxide idle reductions obtained for emission controlled 1968, 1969, and 1970 cars were about equal to those obtained for the pre-emission controlled vehicles, but hydrocarbon reductions were lower. Reductions obtained in federal hot cycles were from 4.1 to 2.1% CO and 1418 to 580 ppm hydrocarbons for pre-1968 cars, and 2.6 to 0.7% and 502 to 308 ppm for 1968–1969 cars.

Idle adjustments lower emissions in the idle, deceleration, and cruise modes up to 30 mph, thus urban driving areas should show the greatest reduction. Total motor vehicle emission reduction in New Jersey would be about 920,000 ton/yr of CO and 101,000 ton/yr of hydrocarbon; a 20 and 32% reduction.     

Idle Emissions from Heavy-Duty Diesel Vehicles: Review and Recent Data

Abstract

Heavy-duty diesel vehicle idling consumes fuel and reduces atmospheric quality, but its restriction cannot simply be proscribed, because cab heat or air-conditioning provides essential driver comfort. A comprehensive tailpipe emissions database to describe idling impacts is not yet available. This paper presents a substantial data set that incorporates results from the West Virginia University transient engine test cell, the E-55/59 Study and the Gasoline/Diesel PM Split Study. It covered 75 heavy-duty diesel engines and trucks, which were divided into two groups: vehicles with mechanical fuel injection (MFI) and vehicles with electronic fuel injection (EFI). Idle emissions of CO, hydrocarbon (HC), oxides of nitrogen (NO_x), particulate matter (PM), and carbon dioxide (CO₂) have been reported. Idle CO₂ emissions allowed the projection of fuel consumption during idling. Test-to-test variations were observed for repeat idle tests on the same vehicle because of measurement variation, accessory loads, and ambient conditions. Vehicles fitted with EFI, on average, emitted [~20 g/hr of CO, 6 g/hr of HC, 86 g/hr of NO_x, 1 g/hr of PM, and 4636 g/hr of CO₂ during idle. MFI equipped vehicles emitted ~35 g/hr of CO, 23 g/hr of HC, 48 g/hr of NO_x, 4 g/hr of PM, and 4484 g/hr of CO₂, on average, during idle. Vehicles with EFI emitted less idleCO, HC, and PM, which could be attributed to the efficient combustion and superior fuel atomization in EFI systems. Idle NO_x, however, increased with EFI, which corresponds with the advancing of timing to improve idle combustion. Fuel injection management did not have any effect on CO₂ and, hence, fuel consumption. Use of air conditioning without increasing engine speed increased idle CO₂, NO_x, PM, HC, and fuel consumption by 25% on average. When the engine speed was elevated from 600 to 1100 revolutions per minute, CO₂ and NO_x emissions and fuel consumption increased by >150%, whereas PM and HC emissions increased by ~100% and 70%, respectively. Six Detroit Diesel Corp. (DDC) Series 60 engines in engine test cell were found to emit less CO, NO_x, and PM emissions and consumed fuel at only 75%of the level found in the chassis dynamometer data. This is because fan and compressor loads were absent in the engine test cell.     

Comparison of the SCAQS Tunnel Study with Other On Road Vehicle Emission Data

The Van Nuys Tunnel experiment conducted in 1987 by Ingalls et al. (see A&WMA Paper 89-137.3), to verify automotive emission inventories as part of the Southern California Air Quality Study (SCAQS), gave higher CO and HC emission-rate values than expected on the basis of automotive-emission models—by factors of approximately 3 and 4, respectively. The CO/NO_X and HC/NO_X emission-rate ratios moreover were higher than expected—by similar factors (NO_X emission rates were about as expected). The purpose of the present paper is to review the literature on dynamometer and on-road (in tunnels and along roadways) testing of in-use vehicles, and on urban-air CO/HC/NO_X concentration ratios, to see whether the Van Nuys Tunnel results are reasonable in terms of previous experience. The conclusions are that (1) on-road CO and HC emissions higher than expected have been reported before, (2) on-road CO and HC emissions consistent with the Van Nuys Tunnel results have been reported before, and (3) on-road CO/NO_X and HC/NO_X emission-rate ratios higher than expected have been reported before. The Van Nuys Tunnel NO_X results actually are lower than in other on-road experiments, and the CO/NO_X and HC/NO_X ratios consequently are higher. The higher-than-predicted CO/NO_X and HC/NO_X ratios at Van Nuys and other on-road sites suggest richer operation on-road than predicted or than observed in the inuse- vehicle dynamometer tests which serve as the model inputs. Support for these suggestions and conclusions is found in comparison of urban-air and emission-inventory HC/NO_X ratios.     

Real-world fuel use and gaseous emission rates for flex fuel vehicles operated on E85 versus gasoline

Flex fuel vehicles (FFVs) typically operate on gasoline or E85, an 85%/15% volume blend of ethanol and gasoline. Differences in FFV fuel use and tailpipe emission rates are quantified for E85 versus gasoline based on real-world measurements of five FFVs with a portable emissions measurement system (PEMS), supplemented chassis dynamometer data, and estimates from the Motor Vehicle Emission Simulator (MOVES) model. Because of inter-vehicle variability, an individual FFV may have higher nitrogen oxide (NO_x) or carbon monoxide (CO) emission rates on E85 versus gasoline, even though average rates are lower. Based on PEMS data, the comparison of tailpipe emission rates for E85 versus gasoline is sensitive to vehicle-specific power (VSP). For example, although CO emission rates are lower for all VSP modes, they are proportionally lowest at higher VSP. Driving cycles with high power demand are more advantageous with respect to CO emissions, but less advantageous for NO_x. Chassis dynamometer data are available for 121 FFVs at 50,000 useful life miles. Based on the dynamometer data, the average difference in tailpipe emissions for E85 versus gasoline is ?23% for NO_x, ?30% for CO, and no significant difference for hydrocarbons (HC). To account for both the fuel cycle and tailpipe emissions from the vehicle, a life cycle inventory was conducted. Although tailpipe NO_x emissions are lower for E85 versus gasoline for FFVs and thus benefit areas where the vehicles operate, the life cycle NO_x emissions are higher because the NO_x emissions generated during fuel production are higher. The fuel production emissions take place typically in rural areas. Although there are not significant differences in the total HC emissions, there are differences in HC speciation. The net effect of lower tailpipe NO_x emissions and differences in HC speciation on ozone formation should be further evaluated.

Implications: Reported comparisons of flex fuel vehicle (FFV) tailpipe emission rates for E85 versus gasoline have been inconsistent. To date, this is the most comprehensive evaluation of available and new data. The large range of inter-vehicle variability illustrates why prior studies based on small sample sizes led to apparently contradictory findings. E85 leads to significant reductions in tailpipe nitrogen oxide (NO_x) and carbon monoxide (CO) emission rates compared with gasoline, indicating a potential benefit for ozone air quality management in NO_x-limited areas. The comparison of FFV tailpipe emissions between E85 and gasoline is sensitive to power demand and driving cycles.     

Emissions from lit-use Motor Vehicles in Los Angeles: A Pilot Study of Remote Sensing and the Inspection and Maintenance Program

As part of a major field study to understand the causes of persistent, elevated carbon monoxide pollution episodes in Los Angeles, we performed a project to understand the emissions of vehicles in use. In this experiment, we assessed the accuracy of a remote sensing instrument designed to measure CO concentrations from vehicles as they were driven on the road. The remote sensor was shown to be accurate within ten percent of the directly measured tailpipe value. We performed a roadside inspection on 60 vehicles and demonstrated that the remote sensor could be used as an effective surveillance tool to identify high CO-emitting vehicles. We also compared the roadside data set to the biennial Smog Check (I/M) tests for the same vehicles, and observed that carbon monoxide and exhaust hydrocarbons from high emitters were much higher than when the vehicles received their routine inspection. Furthermore, for the high-emitting vehicles in this data set, the length of time since the biennial Smog Check had little influence on the cars’ emissions in the roadside inspection.     

Estimating Full IM240 Emissions from Partial Test Results: Evidence from Arizona

ABSTRACT

The expense and inconvenience of enhanced-vehicle-emissions testing using the full 240-second dynamometer test has led states to search for ways to shorten the test process. In fact, all states that currently use the IM240 allow some type of fast-pass, usually as early in the test as second 31, and Arizona has allowed vehicles to fast-fail after second 93. While these shorter tests save states millions of dollars in inspection lanes and driver costs, there is a loss of information since test results are no longer comparable across vehicles. This paper presents a methodology for estimating full 240-second results from partial-test results for three pollutants: HC, CO, and NO_x. If states can convert all tests to consistent IM240 readings, they will be able to better characterize fleet emissions and to evaluate the impact of inspection and maintenance and other programs on emissions over time. Using a random sample of vehicles in Arizona which received full 240-second tests, we use regression analysis to estimate the relationship between emissions at second 240 and emissions at earlier seconds in the test. We examine the influence of other variables such as age, model-year group, and the pollution level itself on this relationship. We also use the estimated coefficients in several applications. First, we try to shed light on the frequent assertion that the results of the dynamometer test provide guidance for vehicle repair of failing vehicles. Using a probit analysis, we find that the probability that a failing vehicle will pass the test on the first retest is greater the longer the test has progressed. Second, we test the accuracy of our estimates for forecasting fleet emissions from partial-test emissions results in Arizona. We find forecasted fleet average emissions to be very close to the actual fleet averages for light-duty vehicles, but not quite as good for trucks, particularly when NO_x emissions are forecast.     

Investigating the real-world emission characteristics of light-duty gasoline vehicles and their relationship to local socioeconomic conditions in three communities in Los Angeles,California

This paper discusses results from a vehicular emissions research study of over 350 vehicles conducted in three communities in Los Angeles, CA, in 2010 using vehicle chase measurements. The study explores the real-world emission behavior of light-duty gasoline vehicles, characterizes real-world super-emitters in the different regions, and investigates the relationship of on-road vehicle emissions with the socioeconomic status (SES) of the region. The study found that in comparison to a 2007 earlier study in a neighboring community, vehicle emissions for all measured pollutants had experienced a significant reduction over the years, with oxides of nitrogen (NO_X) and black carbon (BC) emissions showing the largest reductions. Mean emission factors of the sampled vehicles in low-SES communities were roughly 2–3 times higher for NO_X, BC, carbon monoxide, and ultrafine particles, and 4–11 times greater for fine particulate matter (PM_2.5) than for vehicles in the high-SES neighborhood. Further analysis indicated that the emission factors of vehicles within a technology group were also higher in low-SES communities compared to similar vehicles in the high-SES community, suggesting that vehicle age alone did not explain the higher vehicular emission in low-SES communities.

Evaluation of the emission factor distribution found that emissions from 12% of the sampled vehicles were greater than five times the mean from all of the sampled fleet, and these vehicles were consequently categorized as “real-world super-emitters.” Low-SES communities had approximately twice as many super-emitters for most of the pollutants as compared to the high-SES community. Vehicle emissions calculated using model-year-specific average fuel consumption assumptions suggested that approximately 5% of the sampled vehicles accounted for nearly half of the total CO, PM_2.5, and UFP emissions, and 15% of the vehicles were responsible for more than half of the total NO_X and BC emissions from the vehicles sampled during the study.

Implications: This study evaluated the real-world emission behavior and super-emitter distribution of light-duty gasoline vehicles in California, and investigated the relationship of on-road vehicle emissions with local socioeconomic conditions. The study observed a significant reduction in vehicle emissions for all measured pollutants when compared to an earlier study in Wilmington, CA, and found a higher prevalence of high-emitting vehicles in low-socioeconomic-status communities. As overall fleet emissions decrease from stringent vehicle emission regulations, a small fraction of the fleet may contribute to a disproportionate share of the overall on-road vehicle emissions. Therefore, this work will have important implications for improving air quality and public health, especially in low-SES communities.     

Estimation of road vehicle exhaust emissions from 1992 to 2010 and comparison with air quality measurements in Genoa,Italy

An investigation into road transport exhaust emissions in the Genoa urban area was performed by comparing the quantities of carbon monoxide (CO), nitrogen oxides (NO_x), nitrogen dioxide (NO₂) and particulate matter (PM) emitted by different vehicle categories with air quality measurements referred to the same pollutants. Exhaust emissions were evaluated by applying the PROGRESS (computer PROGramme for Road vehicle EmiSSions evaluation) code, developed by the Internal Combustion Engines Group of the University of Genoa, to eight different years (from 1992 to 2010), considering spark ignition and Diesel passenger cars and light duty vehicles, heavy duty vehicles and buses, motorcycles and mopeds. Changes in terms of vehicles number, mileage and total emissions are presented together with relative distributions among the various vehicle categories. By comparing 1992 and 2010 data, calculated trends show a 7% increase in the number of vehicles, with total mileage growing at a faster rate (approx. 22%); total emissions decrease considerably, by approximately 50% for NO_x and PM, 70% for HC and 80% for CO, due to improvements in engines and fuels forced by the stricter European legislation and the fleet renewal, while primary NO₂ emission will be very close to 1992 level, after a decrease of about 18% in 2000.Air quality was analysed by selecting traffic and background measuring stations from the monitoring network managed by the Environmental Department of the Province of Genoa: average annual concentrations of considered pollutants from 1994 to 2007 were calculated in order to obtain the relative historical trends and compare them with European public health limits and with road vehicle emissions. Though an important reduction in pollutant concentrations has been achieved as a consequence of cleaner vehicles, some difficulties in complying with present and/or future NO₂ and PM₁₀ limits are also apparent, thus requiring suitable measures to be taken by the local authorities.     

Deriving fuel-based emission factor thresholds to interpret heavy-duty vehicle roadside plume measurements

Remote sensing devices have been used for decades to measure gaseous emissions from individual vehicles at the roadside. Systems have also been developed that entrain diluted exhaust and can also measure particulate matter (PM) emissions. In 2015, the California Air Resources Board (CARB) reported that 8% of in-field diesel particulate filters (DPF) on heavy-duty (HD) vehicles were malfunctioning and emitted about 70% of total diesel PM emissions from the DPF-equipped fleet. A new high-emitter problem in the heavy-duty vehicle fleet had emerged. Roadside exhaust plume measurements reflect a snapshot of real-world operation, typically lasting several seconds. In order to relate roadside plume measurements to laboratory emission tests, we analyzed carbon dioxide (CO₂), oxides of nitrogen (NO_X), and PM emissions collected from four HD vehicles during several driving cycles on a chassis dynamometer. We examined the fuel-based emission factors corresponding to possible exceedances of emission standards as a function of vehicle power. Our analysis suggests that a typical HD vehicle will exceed the model year (MY) 2010 emission standards (of 0.2 g NO_X/bhp-hr and 0.01 g PM/bhp-hr) by three times when fuel-based emission factors are 9.3 g NO_X/kg fuel and 0.11 g PM/kg using the roadside plume measurement approach. Reported limits correspond to 99% confidence levels, which were calculated using the detection uncertainty of emissions analyzers, accuracy of vehicle power calculations, and actual emissions variability of fixed operational parameters. The PM threshold was determined for acceleration events between 0.47 and 1.4 mph/sec only, and the NO_X threshold was derived from measurements where after-treatment temperature was above 200°C. Anticipating a growing interest in real-world driving emissions, widespread implementation of roadside exhaust plume measurements as a compliment to in-use vehicle programs may benefit from expanding this analysis to a larger sample of in-use HD vehicles.

Implications: Regulatory agencies, civil society, and the public at large have a growing interest in vehicle emission compliance in the real world. Leveraging roadside plume measurements to identify vehicles with malfunctioning emission control systems is emerging as a viable new and useful method to assess in-use performance. This work proposes fuel-based emission factor thresholds for PM and NOx that signify exceedances of emission standards on a work-specific basis by analyzing real-time emissions in the laboratory. These thresholds could be used to prescreen vehicles before roadside enforcement inspection or other inquiry, enhance and further develop emission inventories, and potentially develop new requirements for heavy-duty inspection and maintenance (I/M) programs, including but not limited to identifying vehicles for further testing.     

The Impact of California Phase 2 Reformulated Gasoline on Real-World Vehicle Emissions

ABSTRACT

In mid-1996, California implemented Phase 2 Reformulated Gasoline (RFG). The new fuel was designed to further decrease emissions of hydrocarbons (HC_s), oxides of nitrogen (NO_x), carbon monoxide (CO), sulfur dioxide (SO₂), and other toxic species. In addition, it was formulated to reduce the ozone-forming potential of the HCs emitted by vehicles. Previous studies have observed that emissions from on-road vehicles can differ significantly from those predicted by mobile source emissions models, and so it is important to quantify the change in emissions in a real-world setting. In October 1995, prior to the introduction of California Phase 2 RFG, the Desert Research Institute (DRI) performed a study of vehicle emissions in Los Angeles' Sepulveda Tunnel. This study provided a baseline against which the results of a second experiment, conducted in July 1996, could be compared to evaluate the impact of California Phase 2 RFG on emissions from real-world vehicles. Compared with the 1995 experiment, CO and NO_x emissions exhibited statistically significant decreases, while the decrease in non-methane hydrocarbon emissions was not statistically significant.

Changes in the speciated HC emissions were evaluated. The benzene emission rate decreased by 27% and the overall emission rate of aromatic compounds decreased by 22% comparing the runs with similar speeds. Emissions of alkenes were virtually unchanged; however, emissions of combustion related unsaturates (e.g., acetylene, ethene) increased, while heavier alkenes decreased. The emission rate of methyl tertiary butyl ether (MTBE) exhibited a larger increase. Overall changes in the ozone-forming potential of the emissions were not significantly different, with the increased contributions to reactivity from paraffins, ole-fins, and MTBE being offset by a large decrease in reactivity due to aromatics.     

An Analysis of Michigan and California CO Remote Sensing Measurements

Abstract

Remote sensing measurements of CO emissions from on-road vehicles were made in California in 1991 and in Michigan in 1992. It was determined that both fleets had a small linear increase in the high emitter frequency (vehicles emitting more than 4% CO) as a function of vehicle age for 1986 and newer model vehicles. Although high emitting vehicles were only a small minority of the fleet, they had a dominant impact on the mean CO and total CO emitted by the fleet. In Michigan, the highest emitting 5% of passenger cars generated 45% of the CO from cars. In California, the highest emitting 5% of passenger cars generated 38% of the CO from cars. There was a high correlation between the mean CO emitted by each model year of vehicle and the frequency of high emitting vehicles within the model year for both the Michigan and California fleets. The frequency of high emitters within any model year had no obvious relation to that model year’s certification standards. The high emitter frequencies for vehicles less than nine years old were very similar for the California and Michigan fleets. An increase in the high emitter frequency in the ten-year-old and older Michigan passenger car fleet (relative to the California passenger car fleet), suggests, but does not conclusively demonstrate, that the rate of high emitters in Michigan and California is reduced by the inspection and maintenance (I/M) programs.     

Emissions profile from new and in-use handheld, 2-stroke engines

The objective of this study was to characterize exhaust emissions from a series of handheld, 2-stroke small engines. A total of 23 new and used engines from model years 1981–2003 were studied; these engines spanned three phases of emission control (pre-control, phase-1, phase-2). Measured emissions included carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NO_x), hydrocarbons (HC), fine particulate matter (PM_2.5), and sulfur dioxide (SO₂). Emissions reductions in CO (78%) and HC (52%) were significant between pre-control and phase-2 engines. These reductions can be attributed to improvements in engine design, reduced scavenging losses, and implementation of catalytic exhaust control. Total hydrocarbon emissions were strongly correlated with fuel consumption rates, indicating varying degrees of scavenging losses during the intake/exhaust stroke. The use of a reformulated gasoline containing 10% ethanol resulted in a 15% decrease in HC and a 29% decrease in CO emissions, on average. Increasing oil content of 2-stroke engine fuels results in a substantial increase of PM_2.5 emissions as well as smaller increases in HC and CO emissions. Results from this study enhance existing emission inventories and appear to validate predicted improvements to ambient air quality through implementation of new phase-2 handheld emission standards.