A wind tunnel study of dense gas dispersion in a neutral boundary layer over a rough surface

Measurements of the vertical entrainment velocity into two-dimensional dense gas plumes over fully rough surfaces were carried out as part of a co-operative research programme with wind tunnel facilities in the USA. This paper presents results obtained for neutral boundary layer conditions in the EnFlo wind tunnel at the University of Surrey; a companion paper treats the stable boundary layer case. Entrainment velocities, W_E, were deduced from the streamwise development of the concentration field, non-dimensionalised with respect to the friction velocity in the undisturbed flow, u^*, and correlated with the plume Richardson number, Ri^*. Results for Richardson numbers in the range Ri^*<15 were found to be well fitted by the empirical expression: W_E/u^*=0.65/(1+0.2Ri^*). Flow visualisation studies showed layered plume structures with a sharp upper interface at higher Richardson numbers and in this regime turbulent motion below the interface became progressively more intermittent as Ri^* increased. Measured turbulence levels collapsed within such high Richardson number plumes and flow and dispersion were significantly affected by molecular processes. Up-welling above the source was observed when the emission speed exceeded the approach flow friction velocity, though there was no clear evidence that this affected plume behaviour away from the immediate vicinity of the source.     

An efficient approach of aerosol thermodynamic equilibrium predictions by the HDMR method

In this paper, we develop a new and efficient approach for high dimensional atmospheric aerosol thermodynamic equilibrium predictions. The multi-phase and multi-component aerosol thermodynamic input–output systems are solved by the high dimensional model representation (HDMR) method combining with the moving multiple cut points. The developed approach improves the accuracy of numerical simulations for the general high dimensional input–output systems compared with the standard cut-HDMR method. It can simulate efficiently the atmospheric aerosol thermodynamic equilibrium problems in a large range of aerosol concentrations from 10^?10 to 10^?6 mol m^?3. Numerical experiments show that the approach has great computational efficiency and the CPU-time of the approach is much less than that of ISORROPIA. The method does excellent performance in predicting high dimensional aerosol thermodynamic components as well as particulate matters (PMs).     

Effects of nitrogen application rate and a nitrification inhibitor dicyandiamide on methanotroph abundance and methane uptake in a grazed pasture soil

Methane-oxidizing bacteria (methanotrophs) in the soil are a unique group of methylotrophic bacteria that utilize methane (CH₄) as their sole source of carbon and energy which limit the flux of methane to the atmosphere from soils and consume atmospheric methane. A field experiment was conducted to determine the effect of nitrogen application rates and the nitrification inhibitor dicyandiamide (DCD) on the abundance of methanotrophs and on methane flux in a grazed pasture soil. Nitrogen (N) was applied at four different rates, with urea applied at 50 and 100 kg N ha^?1 and animal urine at 300 and 600 kg N ha^?1. DCD was applied at 10 kg ha^?1. The results showed that both the DNA and selected mRNA copy numbers of the methanotroph pmoA gene were not affected by the application of urea, urine or DCD. The methanotroph DNA and mRNA pmoA gene copy numbers were low in this soil, below 7.13?×?10³ g^?1 soil and 3.75?×?10³ μg^?1 RNA, respectively. Daily CH₄ flux varied slightly among different treatments during the experimental period, ranging from ?12.89 g CH₄ ha^?1 day^?1 to ?0.83 g CH₄ ha^?1 day^?1, but no significant treatment effect was found. This study suggests that the application of urea fertilizer, animal urine returns and the use of the nitrification inhibitor DCD do not significantly affect soil methanotroph abundance or daily CH₄ fluxes in grazed grassland soils.     

Turbulent mixing in a barbed plate-to-plate electrostatic precipitator

The electrical and fluid dynamical characteristics of a barbed plate-to-plate electrostatic precipitator are compared with those of a conventional wire-to-plate precipitator under particle-free conditions. The barbed plate electrode design is based on the concept that a more uniform distribution of current within the flow channel may reduce the scale of the corona-induced electrohydrodynamic flow and thus decrease particle mixing. Current-voltage relationships and hot-film anemometer measurements of turbulence intensities, integral length scales and eddy diflusivities are presented for current densities as high as9mAm⁻²at gas speeds of 0.5,1.0 and 2.0 m s⁻¹. Visual inspection of the discharge pattern indicates that the scale of the current inhomogeneity is reduced. Flow visualization and measurements of integral length scales confirm that the barbed plate design does reduce the scale of the electrically induced flow. Even though downstream turbulence levels are increased in the planar geometry, gas diffusivities are not substantially reduced. Additional study of the inter-electrode gas flow field and particle collection efficiency is necessary to determine the practical viability of the barbed plate precipitator.     

Cloud point extraction for the preconcentration of palladium and lead in environmental samples and determination by flow injection flame atomic absorption spectrometry

Purpose

An online cloud-point extraction (CPE) coupled with flow injection method is developed for the separation and preconcentration of palladium and lead from various matrices using flame atomic absorption spectrometry (FAAS).

Method

The method employs the formation of complexes of the metallic species with dimethylglyoxime, which are subsequently entrapped in the micelles of the surfactant Triton X-114, upon increase of the solution temperature to 60°C and loaded into the flow injection system at a flow rate of 4.6?mL?min^?1. The surfactant rich-phase was retained in a minicolumn packed with animal wool at pH?6 and eluted with 1.0?mol?L^?1 nitric acid in methanol at a flow rate of 1.1?mL?min^?1 directly into the nebulizer of the FAAS. The CPE variables and flow injection conditions affecting the analytical performance of the combined methodology was studied and optimized.

Results

Under the optimized conditions for 25?mL of preconcentrated solution, the enrichment factors were 51 and 44, and the limit of detections were 1.0 and 1.4?ng?mL^?1 for palladium and lead, respectively. Finally, the developed method was applied for the determination of palladium and lead in street dust, soil, radiology waste, catalytic converter, and urban aerosol samples.

Conclusions

Cloud-point extraction coupled with flow injection-FAAS was proposed as an effective preconcentration and separation method for Pd and Pb determination in radiology waste, road dust, soil, and urban aerosol samples. The most favorable feature of this method is its much higher selectivity, sensitivity, rapidity, good extraction efficiency, and employs the green chemistry concept, as it does not require the addition of toxic chemicals. In addition, this proposed method gives very low detection limits and good relative standard.     

Characterization of bacterial communities at heavy-metal-contaminated sites

The microbial community in soil samples from two long-term contaminated sites was characterized by using culture-dependent and culture-independent methods. The two sites investigated contained high amounts of heavy metals and were located in the upper Silesia Industrial Region in southern Poland. The evaluation of the aerobic soil microbial population clearly demonstrated the presence of considerable numbers of viable, culturable bacteria at both sites. A high fraction of the bacterial population was able to grow in the presence of high amounts of metals, i.e. up to 10 mM Zn²⁺, 3 mM Pb²⁺ or 1 mM Cu²⁺. Site 1 contained significantly (P < 0.05) lower bacterial numbers growing in the presence of 10 mM Zn²⁺ than site 2, while the opposite was observed for bacteria tolerating 1 mM Cu²⁺. This coincided with the contents of these two metals at the two sites. Ecophysiological (EP) indices for copiotrophs (r-strategists) and oligotrophs (K-strategists) pointed to high bacterial diversity at both sites. Fluorescence in situ hybridization (FISH) analysis indicated that Actinobacteria and Proteobacteria represent the physiologically active fraction of bacteria at the two sites. Shannon diversity (H′) indices for FISH-detected bacterial phylogenetic groups were not significantly different at the two sites.     

Uptake of nitrous acid and nitrogen oxides by nylon surfaces: Implications for nitric acid measurement

The interference in HNO₃ determination due to HNO₂ and NO_x retention on nylon filters has been evaluated in laboratory and field conditions. Nitrous acid is retained on nylon filters with efficiencies varying from 25% at 12ℓ min⁻¹ to 80% at 2ℓ min⁻¹, yielding NO₂⁻ ion. In ambient sampling performed during photochemical smog episodes, NO₂⁻ is oxidized to NO₃⁻ with conversion factors up to 100%, resulting in a positive bias in HNO₃ determination.NO₂ reacts heterogeneously with H₂O on nylon surfaces according to the reaction 2NO₂ + H₂O → HNO₂ + HNO₃ with a removal constant of about 1 × 10⁻⁴ ms⁻¹ at a H₂O concentration of 20,000 ppm. The resulting nitrite and nitrate are independent of the sampling flow rate, while NO₂ concentration, sampling time and exposed nylon surface area play a directly proportional role. Accordingly, the relative interference of NO₂ with respect to HNO₃ determination is almost negligible for nylon filters, usually run at relatively high flow rates, while it may be significant for nylon denuders, which are characterized by larger exposed surfaces and lower operating flow rates.     

Tritium and Cl as constraints on fast fracture flow and percolation flux in the unsaturated zone at Yucca Mountain

An analysis of tritium and ³⁶Cl data collected at Yucca Mountain, Nevada suggests that fracture flow may occur at high velocities through the thick unsaturated zone. The mechanisms and extent of this “fast flow” in fractures at Yucca Mountain are investigated with data analysis, mixing models and several one-dimensional modeling scenarios. The model results and data analysis provide evidence substantiating the weeps model [Gauthier, J.H., Wilson, M.L., Lauffer, F.C., 1992. Proceedings of the Third Annual International High-level Radioactive Waste Management Conference, vol. 1, Las Vegas, NV. American Nuclear Society, La Grange Park, IL, pp. 891–989] and suggest that fast flow in fractures with minimal fracture–matrix interaction may comprise a substantial proportion of the total infiltration through Yucca Mountain. Mixing calculations suggest that bomb-pulse tritium measurements, in general, represent the tail end of travel times for thermonuclear-test-era (bomb-pulse) infiltration. The data analysis shows that bomb-pulse tritium and ³⁶Cl measurements are correlated with discrete features such as horizontal fractures and areas where lateral flow may occur. The results presented here imply that fast flow in fractures may be ubiquitous at Yucca Mountain, occurring when transient infiltration (storms) generates flow in the connected fracture network.     

Influence of air mass source region on nanoparticle events and hygroscopicity in central Virginia,U.S.

During autumn, 2006, variation in the frequency of aerosol nucleation events, as inferred from nanoparticle growth events, and associated hygroscopicity were investigated as a function of air mass transport history at a mixed deciduous forest in central Virginia, U.S. Above-canopy size distributions of aerosols between 0.012 and 0.700 μm diameter, size-resolved particle hygroscopicity at eight dry diameters between 0.012 and 0.400 μm, and cloud condensation nuclei (CCN) activity were characterized. Air mass back trajectories were clustered to identify source regions. Growth events were most frequent in fast-moving air masses (mean = 9 m s^?1) that originated over the north central U.S. Under these flow regimes, mean values for preexisting sub-μm aerosol number concentrations (4700 cm^?3), corresponding surface area (142 μm² cm^?3), air temperature (6.2 °C), and relative humidity (RH, 49.4%) were relatively low compared to other regimes. Under stagnant flow conditions (mean = 3 m s^?1), mean number concentrations were higher (>6000 cm^?3) and size fractions <0.1 μm diameter exhibited enhanced hygroscopicity compared to other source regions. These results indicate that precursors emitted into relatively clean, cold, and dry air transported over the southeastern U.S. reacted to form condensable intermediates that subsequently produced new aerosols via nucleation and growth. This pathway was an important source for CCN. During events in October, nanoparticles were produced in greater numbers and grew more rapidly compared to November and December.     

Repeated batch and continuous degradation of chlorpyrifos by Pseudomonas putida

The present study was undertaken with the objective of studying repeated batch and continuous degradation of chlorpyrifos (O,O-diethyl O-3,5,6-trichloropyridin-2-yl phosphorothioate) using Ca-alginate immobilized cells of Pseudomonas putida isolated from an agricultural soil, and to study the genes and enzymes involved in degradation. The study was carried out to reduce the toxicity of chlorpyrifos by degrading it to less toxic metabolites. Long-term stability of pesticide degradation was studied during repeated batch degradation of chlorpyrifos, which was carried out over a period of 50 days. Immobilized cells were able to show 65% degradation of chlorpyrifos at the end of the 50th cycle with a cell leakage of 112 × 10³ cfu mL^?1. During continuous treatment, 100% degradation was observed at 100 mL h^?1 flow rate with 2% chlorpyrifos, and with 10% concentration of chlorpyrifos 98% and 80% degradation was recorded at 20 mL h^?1 and 100 mL h^?1 flow rate respectively. The products of degradation detected by liquid chromatography–mass spectrometry analysis were 3,5,6-trichloro-2-pyridinol and chlorpyrifos oxon. Plasmid curing experiments with ethidium bromide indicated that genes responsible for the degradation of chlorpyrifos are present on the chromosome and not on the plasmid. The results of Polymerase chain reaction indicate that a ~890-bp product expected for mpd gene was present in Ps. putida. Enzymatic degradation studies indicated that the enzymes involved in the degradation of chlorpyrifos are membrane-bound. The study indicates that immobilized cells of Ps. putida have the potential to be used in bioremediation of water contaminated with chlorpyrifos.     

Characterization of Particulate Matter and Gaseous Emissions of a C-130H Aircraft

Abstract

The gaseous and nonvolatile particulate matter (PM) emissions of two T56-A-15 turboprop engines of a C-130H aircraft stationed at the 123rd Airlift Wing in the Kentucky Air National Guard were characterized. The emissions campaign supports the Strategic Environmental Research and Development Program (SERDP) project WP-1401 to determine emissions factors from military aircraft. The purpose of the project is to develop a comprehensive emissions measurement program using both conventional and advanced techniques to determine emissions factors of pollutants, and to investigate the spatial and temporal evolutions of the exhaust plumes from fixed and rotating wing military aircraft. Standard practices for the measurement of gaseous emissions from aircraft have been well established; however, there is no certified methodology for the measurement of aircraft PM emissions. In this study, several conventional instruments were used to physically characterize and quantify the PM emissions from the two turboprop engines. Emissions samples were extracted from the engine exit plane and transported to the analytical instrumentation via heated lines. Multiple sampling probes were used to assess the spatial variation and obtain a representative average of the engine emissions. Particle concentrations, size distributions, and mass emissions were measured using commercially available aerosol instruments. Engine smoke numbers were determined using established Society of Automotive Engineers (SAE) practices, and gaseous species were quantified via a Fourier-transform infrared-based gas analyzer. The engines were tested at five power settings, from idle to take-off power, to cover a wide range of operating conditions. Average corrected particle numbers (PNs) of (6.4–14.3) × 10⁷ particles per cm³ and PN emission indices (EI) from 3.5 × 10¹⁵ to 10.0 × 10¹⁵ particles per kg-fuel were observed. The highest PN EI were observed for the idle power conditions. The mean particle diameter varied between 50 nm at idle to 70 nm at maximum engine power. PM mass EI ranged from 1.6 to 3.5 g/kg-fuel for the conditions tested, which are in agreement with previous T56 engine measurements using other techniques. Additional PM data, smoke numbers, and gaseous emissions will be presented and discussed.     

Determination of deployment specific chemical uptake rates for SDB-RPD Empore disk using a passive flow monitor (PFM)

The use of the adsorbent styrenedivinylbenzene-reverse phase sulfonated (SDB-RPD) Empore disk in a chemcatcher type passive sampler is routinely applied in Australia when monitoring herbicides in aquatic environments. One key challenge in the use of passive samplers is mitigating the potentially confounding effects of varying flow conditions on chemical uptake by the passive sampler. Performance reference compounds (PRCs) may be applied to correct sampling rates (R_s) for site specific changed in flow and temperature however evidence suggests the use of PRCs is unreliable when applied to adsorbent passive samplers. The use of the passive flow monitor (PFM) has been introduced for the assessment of site-specific changes in water flow. In the presented study we have demonstrated that the R_s at which both atrazine and prometryn are accumulated within the SDB-RPD-Empore disk is dependent on the flow conditions. Further, the calibration of the measured R_s for chemical uptake by the SDB-RPD-Empore disk to the mass lost from the PFM has shown that the PFM provides an accurate measure of R_s for flow velocities from 0 to 16 cm s⁻¹. Notably, for flow rates >16 cm s⁻¹, a non linear increase in the R_s of both herbicides was observed which indicates that the key resistance to uptake into the SDB-RPD Empore disk is associated with the diffusion through the overlying diffusion limiting membrane. Overall the greatest uncertainty remains at very low flow conditions, which are unlikely to often occur in surface waters. Validation of the PFM use has also been undertaken in a limited field study.     

实时荧光定量PCR对A2/O短程硝化系统内氨氧化菌的定量分析

通过控制好氧区低DO浓度以及缩短好氧实际水力停留时间(actual hydraulic retention time,AHRT),在处理低C/N比实际生活污水的A2/O工艺中,成功启动并维持了短程硝化反硝化;系统亚硝酸盐积累率稳定维持在90%左右,氨氮去除率在95%以上。通过提取富集氨氧化菌(ammonia oxidizing bacteria,AOB)的基因组DNA,经两次常规PCR扩增和琼脂糖凝胶电泳,以纯化回收的DNA扩增片段作为实时荧光定量PCR检测AOB数量的DNA标准品,建立了检测AOB数量的实时荧光定量PCR标准曲线。利用实时荧光定量PCR技术比较了A2/O系统在不同运行条件及亚硝酸盐积累率情况下AOB菌群数量。结果表明,随着系统亚硝酸盐积累率的上升,系统内AOB菌群数量也大幅上升。全程硝化和短程硝化时,系统内的AOB菌群数量分别为5.28×109cells/g MLVSS和3.95×1010cells/g MLVSS。此外,亚硝酸盐积累率的下降相对于AOB菌群数量的下降有一定的滞后性。     

Flow and transport in fractured tuff at Yucca Mountain: numerical experiments on fast preferential flow mechanisms

Recent discovery of bomb-related ³⁶Cl at depth in fractured tuff in the unsaturated zone at the Yucca Mountain candidate high-level waste (HLW) repository site has called into question the usual modeling assumptions based on the equivalent continuum model (ECM). A dual continuum model (DCM) for simulating transient flow and transport at Yucca Mountain is developed. In order to ensure properly converged flow solutions, which are used in the transport simulation, a new flow solution convergence criteria is derived. An extensive series of simulation studies is presented which indicates that rapid movement of solute through the fractures will not occur unless there are intense episodic infiltration events. Movement of solute in the environs of the repository is enhanced if the properties of the tuff layer at the repository horizon are modified from current best-estimate values. Due to a large advective–dispersive coupling between the matrix and fractures, the matrix acts as a major buffer which inhibits rapid transport along the fractures. Consequently, fast movement of solutes through the fractures to the repository depth can only be explained if the matrix–fracture coupling term is significantly reduced from a value that would be calculated on the basis of data currently available.     

Correlation of Dust Scrubber Efficiency

The grid-type electrostatic precipitator¹ evolved from some basic research into the collection of airborne charged dust particles in the wake of a flat, metallic, perforated plate under the action of an externally applied electric field. In the earliest experiments in the laboratory² a flat grounded perforated plate (or grid) was placed at right angles to an air stream moving at 6 ft/sec and an electric field was created on its downstream side by the placement of a second grid, bearing high negative potential, just downstream of the first. Negatively charged dust particles, carried along by the air stream through the openings in the first of the two grids, collected on the downstream face of the upstream grid as a result of the electric force acting on them in the direction opposing the air flow. Measured values of dust collection efficiency could not be accounted for simply by resolving the directly opposing mainstream air flow and electrostatic forces. The concept of vortex-enhanced precipitation was therefore proposed in order to explain the experimental results.     

High Volume Sampling: Errors Incurred during Passive Sample Exposure Periods

The current Federal EPA reference method for the determination of total suspended particulate matter (TSP) in the atmosphere is the high volume method (hi-vol).¹ The hi-vol sampler is normally operated for a 24 hr period by drawing air through an 8 X 10 in. glass fiber filter at an air sampling flow rate of between 40-60 cfm. TSP samples are presently collected in this manner every 6th day (61 samples/year). Results are used to determine compliance with existing National Primary Ambient Air Quality Standards for TSP (i.e., 260 µg/m³, maximum 24 hr average, not to be exceeded more than once a year; 75 µg/m³, annual geometric mean). However, when the sampling frequency is diminished to only 61 out of a possible 365 measurements each year, the degree of certainty associated with meeting these air quality standards is also decreased.^2,3 This partial sampling schedule also introduces other sampling errors. One such error caused by the exposure of the collection filter both prior and subsequent to the desired sampling day is the subject of the following discussion.     

Storm flow export of metolachlor from a coastal plain watershed

Abstract

During an 18‐month (1994–1995) survey of the surface water in an Atlantic Coastal Plain watershed, metolachlor was most frequently detected during storm flow events. Therefore, a sampling procedure, focused on storm flow, was implemented in June of 1996. During 1996, three tropical cyclones made landfall within 150 km of the watershed. These storms, as well as several summer thunderstorms, produced six distinct storm flow events within the watershed. Metolachlor was detected leaving the watershed during each event. In early September, Hurricane Fran produced the largest storm flow event and accounted for the majority of the metolachlor exports. During the storm event triggered by Hurricane Fran, the highest daily average flow (7.5 m² s^‐1) and highest concentration (5.1 μg L^‐1) ever measured at the watershed outlet were recorded. Storm flow exports leaving the watershed represented 0.1 g ha^‐1 or about 0.04% of active ingredient applied.     

Uncertainty associated with the gravimetric measurement of particulate matter concentration in ambient air

This work applied a propagation of uncertainty method to typical total suspended particulate (TSP) sampling apparatus in order to estimate the overall measurement uncertainty. The objectives of this study were to estimate the uncertainty for three TSP samplers, develop an uncertainty budget, and determine the sensitivity of the total uncertainty to environmental parameters. The samplers evaluated were the TAMU High Volume TSP Sampler at a nominal volumetric flow rate of 1.42 m³ min^–1 (50 CFM), the TAMU Low Volume TSP Sampler at a nominal volumetric flow rate of 17 L min^–1 (0.6 CFM) and the EPA TSP Sampler at the nominal volumetric flow rates of 1.1 and 1.7 m³ min^–1 (39 and 60 CFM). Under nominal operating conditions the overall measurement uncertainty was found to vary from 6.1 x 10^–6 g m^–3 to 18.0 x 10^–6 g m^–3, which represented an uncertainty of 1.7% to 5.2% of the measurement. Analysis of the uncertainty budget determined that three of the instrument parameters contributed significantly to the overall uncertainty: the uncertainty in the pressure drop measurement across the orifice meter during both calibration and testing and the uncertainty of the airflow standard used during calibration of the orifice meter. Five environmental parameters occurring during field measurements were considered for their effect on overall uncertainty: ambient TSP concentration, volumetric airflow rate, ambient temperature, ambient pressure, and ambient relative humidity. Of these, only ambient TSP concentration and volumetric airflow rate were found to have a strong effect on the overall uncertainty. The technique described in this paper can be applied to other measurement systems and is especially useful where there are no methods available to generate these values empirically.

Implications:?This work addresses measurement uncertainty of TSP samplers used in ambient conditions. Estimation of uncertainty in gravimetric measurements is of particular interest, since as ambient particulate matter (PM) concentrations approach regulatory limits, the uncertainty of the measurement is essential in determining the sample size and the probability of type II errors in hypothesis testing. This is an important factor in determining if ambient PM concentrations exceed regulatory limits. The technique described in this paper can be applied to other measurement systems and is especially useful where there are no methods available to generate these values empirically.     

Analytical model for site-specific isotope fractionation in 13C during sorption: determination by isotopic 13C NMR spectrometry with vanillin as model compound

The aim of this study was to conceive a reactive transport model capable of providing quantitative site-specific enrichment factors for fractionation in ¹³C isotopic content during sorption. As test compound the model treats vanillin, for which the ¹³C isotopic content at natural abundance at each of the 8 carbon positions can be measured by quantitative ¹³C nuclear magnetic resonance spectrometry. This technique determines the isotope ratios with a resolution better than ±1‰ (0.1%) at each carbon position. Site-specific isotope fractionations were recorded in chromatography column experiments with silica RP-18 as stationary phase. The one dimensional reactive transport model accounted for the sorption/desorption behavior of 8 individual ¹³C-isotopomers and one ¹²C-isotopomer of vanillin and reproduced satisfactorily the bulk (average over the whole compound) fractionation observed during elution. After model calibration, the enrichment factors were fitted for each carbon site where a significant fractionation was recorded. To show the interest of such a transport model for environmental studies, the model, extended to three dimensions, was exploited to simulate reactive transport in an aquifer. These results show that significant ¹³C isotope fractionation is expected for 4 out of 8 ¹³C-isotopomers in vanillin, and illustrate that bulk isotope ratios measured by conventional compound specific isotope analysis and mass spectrometry would hardly document significant isotope fractionations in vanillin. It is concluded that modeling of site-specific isotope ratios in molecules is a priori feasible and may help to quantify unknown processes in the environment.     

Differences in airborne particle and gaseous concentrations in urban air between weekdays and weekends

Airborne particle number concentrations and size distributions as well as CO and NO_x concentrations monitored at a site within the central business district of Brisbane, Australia were correlated with the traffic flow rate on a nearby freeway with the aim of investigating differences between weekday and weekend pollutant characteristics. Observations over a 5-year monitoring period showed that the mean number particle concentration on weekdays was (8.8±0.1)×10³ cm⁻³ and on weekends (5.9±0.2)×10³ cm⁻³—a difference of 47%. The corresponding mean particle number median diameters during weekdays and weekends were 44.2±0.3 and 50.2±0.2 nm, respectively. The differences in mean particle number concentration and size between weekdays and weekends were found to be statistically significant at confidence levels of over 99%. During a 1-year period of observation, the mean traffic flow rate on the freeway was 14.2×10⁴ and 9.6×10⁴ vehicles per weekday and weekend day, respectively—a difference of 48%. The mean diurnal variations of the particle number and the gaseous concentrations closely followed the traffic flow rate on both weekdays and weekends (correlation coefficient of 0.86 for particles). The overall conclusion, as to the effect of traffic on concentration levels of pollutant concentration in the vicinity of a major road (about 100 m) carrying traffic of the order of 10⁵ vehicles per day, is that about a 50% increase in traffic flow rate results in similar increases of CO and NO_x concentrations and a higher increase of about 70% in particle number concentration.