The effects of drop size and formulation upon the spread of pesticide droplets impacting on water‐sensitive papers

Abstract

The effects of drop size and formulation upon the spread of pesticide droplets impacting on water‐sensitive papers (WSPs) was investigated. Droplets of diameter 70–350 μm, of four permethrin formulations, were produced using a monosize droplet generator. The droplets were collected on WSPs and in Dow Corning fluid and their diameters measured using a binocular microscope. Spread factors, upon the WSPs, for each dropsize/formulation combination were then calculated. Spread factors varied with both formulation and droplet size and for droplets of 200 and 300 μm diameter spread was significantly correlated with the dynamic surface tension of the formulation. The results suggest that proper calibration of WSPs is necessary for effective droplet sizing.     

A Special Issue from the NARSTO Symposium on Tropospheric Aerosols

This dedicated issue of the Journal of the Air & Waste Management Association contains nine peer-reviewed scientific papers that were presented at the NARSTO Symposium on Tropospheric Aerosols: Science and Decisions in an International Community, held October 24-26, 2000, in Querétaro, Mexico.¹ Other peer-reviewed papers^2-9 appear in a companion issue of Science of the Total Environment to be published in February 2002. More than 130 papers were presented in platform and poster sessions at the meeting. Approximately 28% of the technical presentations dealt with topics from Mexico, and 15% related to Canada, with the remainder discussing U.S. and global topics.     

Workshop on Primary Sulfate Emissions

This article is a summary report on a workshop, Measurement Technology and Characterization of Primary Sulfur Oxides Emission from Combustion Sources, sponsored by the EPA Environmental Sciences Research Laboratory at Research Triangle Park, NC, held in Southern Pines, NC. The objectives of the workshop were: to review and discuss current measurement methods and problem areas for sulfur oxides emission with attention focused on sulfuric acid, sulfates, and sulfur-bearing particulate matter; to review and discuss emission data from various combustion sources operating under different conditions, which include various pollutant controls, fuel composition, excess boiler oxygen, etc.; to delineate and recommend areas in need of research and development effort. Scientists were invited to present the results of their studies on primary sulfate emissions. The 3-day workshop devoted one day to measurement technology, a second to characterization, and a third to critical assessment of the presented papers and development of summary working group reports on each half-day session of the initial 2 days. Thirty-one papers were presented by 29 participants on measurements and characterization. Four working group reports were developed and summarized in the last day. Highlights of the papers and reports are briefly reviewed. Workshop proceedings are available as an EPA publication.     

Report from the Symposium on Air Quality Criteria

Neither time nor space permitted full reporting of the Symposium on Air Quality Criteria, held June 4-5, 1968, in New York City. The Symposium was sponsored by the Air Pollution Control Association, the American Industrial Hygiene Association, the American Petroleum Institute, and the Industrial Medical Association and its educational affiliate, The Occupational Health Institute.

Published here are excerpts from, or author’s abstracts of, the eight principal papers presented at the Symposium.

Not included are the prepared discussions which followed the delivery of the papers.

A full proceedings, including prepared discussions, general discussions, and summation, will be published in the September issue of the Journal of Occupational Medicine, 55 E. Washington Street, Chicago, Illinois 60602.     

BIOLEFF: three databases on air pollution effects on vegetation

Three databases on air pollution effects on vegetation were developed by storing bibliographic and abstract data for technical literature on the subject in a free-form database program, 'askSam'. Approximately 4 000 journal articles have been computerized in three separate database files: BIOLEFF, LICHENS and METALS. BIOLEFF includes over 2 800 articles on the effects of approximately 25 gaseous and particulate pollutants on over 2 000 species of vascular plants. LICHENS includes almost 400 papers on the effects of gaseous and heavy metal pollutants on over 735 species of lichens and mosses. METALS includes over 465 papers on the effects of heavy metals on over 830 species of vascular plants. The combined databases include articles from about 375 different journals spanning 1905 to the present. Picea abies and Phaseolus vulgaris are the most studied vascular plants in BIOLEFF, while Hypogymnia physodes is the most studied lichen species in LICHENS. Ozone and sulfur dioxide are the most studied gaseous pollutants with about two thirds of the records in BIOLEFF. The combined size of the databases is now about 5.5 megabytes.     

Size Distribution of Participates Emitted from a Horizontal Spike Soderberg Aluminum Reduction Cell

Aerosol size distributions were measured in the air exhausted from a horizontal spike Soderberg aluminum reduction cell at the Kaiser Aluminum and Chemical Corporation plant in Tacoma, Wash. The particle size distributions were measured with the University of Washington cascade impactor, developed specifically for source testing. The particle mass concentrations and size distributions were found to vary significantly with changes in the cell process operations. For a typical aerosol size distribution at the exit of the cell hood the mass mean particle diameter was 5.5 microns and the particle size standard geometric deviation was 25.     

The influence of environmental factors on the molluscicidal activity of Euphorbia milii latex

Abstract

The present study was undertaken to investigate the influence of biotic (snail size and presence of food during the test) and abiotic factors (temperature, water hardness and concentration of organic materials) on the molluscicidal activity of Euphorbia milii latex. Bioassays were conducted with B. glabrata (10 snails per concentration) and snail lethality was evaluated after 24 hr and 48 hr of exposure to lyophilized latex solutions. Neither the degree of water hardness, nor the presence of food during the test affected latex‐induced snail mortality. The snail size had a minor influence on E.milii‐induced snail lethality. Newly‐hatched (shell diameter ≤ 1mm) as well as young (3–8 mm) snails were slightly less susceptible than older (10–25 mm) mollusks. On the other hand, the molluscicidal effect of E.milii latex was modified by environmental factors such as temperature (i.e. LC₅₀ and LC₉₀ values were halved for every 10°C rise in temperature) and concentration of organic materials in the water (i.e. the higher the concentration of organic matter, the higher the LC₅₀ value). The efficacy of E.milii latex as a molluscicide can be modified by factors such as water temperature and concentration of organic materials, and to a lesser extent by snail size.     

The re-imagining of a framework for agricultural land use: A pathway for integrating agricultural practices into ecosystem services,planetary boundaries and sustainable development goals: This article belongs to Ambio’s 50th Anniversary Collection. Theme: Agricultural land use

This paper reflects on the legacy of the Ambio papers by Sombroek et al. (1993), Turner et al. (1994), and Brussaard et al. (1997) on the study of agricultural land use and its impacts on global carbon storage and nutrient dynamics. The papers were published at a time of transition in ecology that involved the integration of humans as components of ecosystems, the formulation of the ecosystem services, and emergence of sustainability science. The papers offered new frameworks to studying agricultural land use across multiple scales in a way that captured causality from interacting components of the system. Each paper argued for more comprehensive data sets; foreseeing the power of network-based science, the potential of molecular technologies to assess biodiversity, and advances in remote sensing. The papers have contributed both conceptual framings and methodological approaches to an ongoing movement to identify a pathway to study agricultural land use and environmental change that fit within the concepts of ecosystem services, planetary boundaries and sustainable development goals.     

A Technique for Respirable Sampling

The purpose of this paper is to describe instrumentation to aerodynamically size suspended particulates found in ambient air and to summarize results of field testing utilizing the new technique.

A four-stage, multiorifice high-volume fractionating impactor with backup filter, which can be operated as a component of the standard high-volume sampler, collects particulate matter in five separate aerodynamic size ranges: 7 micrometer (μm) or larger, 3.3 to 7 μm, 2.0 to 3.3 μm, 1.1 to 2.0 μm, and 0.01 to 1.1 μm.

Comparative field tests utilizing duplicate sampling techniques were conducted to determine the feasibility of using the size fractionator on a routine basis in field operations. Verification of the actual particle size separation was not undertaken; however, earlier tests utilizing laboratory-generated aerosols have been performed with satisfactory results.

The results of field tests indicate that the fractionator can be used to determine the aerodynamic size distribution of particulate matter. A glass fiber surface with a pH of 11.0 was found to adsorb atmospheric acid gases during sampling and thus gave erroneous mass concentration results when compared to the standard high-volume sampler. Glass fiber filters with a pH of 6.5 eliminated the acid gas adsorption.     

Particle size distribution of airborne Aspergillus fumigatus spores emitted from compost using membrane filtration

Information on the particle size distribution of bioaerosols emitted from open air composting operations is valuable in evaluating potential health impacts and is a requirement for improved dispersion simulation modelling. The membrane filter method was used to study the particle size distribution of Aspergillus fumigatus spores in air 50 m downwind of a green waste compost screening operation at a commercial facility. The highest concentrations (approximately 8 × 10⁴ CFU m⁻³) of culturable spores were found on filters with pore diameters in the range 1–2 μm which suggests that the majority of spores are emitted as single cells. The findings were compared to published data collected using an Andersen sampler. Results were significantly correlated (p < 0.01) indicating that the two methods are directly comparable across all particles sizes for Aspergillus spores.     

Variation of particle number and mass concentration in various size ranges of ambient aerosols in Eastern Germany

There is an ongoing debate on the question which size fraction of particles in ambient air may be responsible for short-term responses of the respiratory system as observed in several epidemiological studies. However, the available data on ambient particle concentrations in various size ranges are not sufficient to answer this question.Therefore, on 180 days during the winter 1991/92 daily mean size distributions of ambient particles were determined in. Erfurt, a city in Eastern Germany. In the range 0.01–0.3 μm particles were classified by an electrical mobility analyzer and in the range 0.1–2.5 μm by an optical particle counter. From the derived size distributions, number and mass concentrations were calculated.The mean number concentration over this period of time was governed by particles smaller than 0.1 μm (72%), whereas the mean mass concentration was governed by particles in the size range 0.1–0.5 pm (83%). The contribution of particles larger than 0.5 μm to the overall number concentration was negligible and so was the contribution of particles smaller than 0.1 μm to the overall mass concentration. Furthermore, total number and mass concentrations in the range 0.01–2.5 μm were poorly correlated.The results suggest that particles larger than 2.5 μm (or even larger than 0.5 μm) are rare in the European urban environment so that the inhalation of these particles is probably not relevant for human health. Since particle number and mass concentrations can be considered poorly correlated variables, more insight into health-related aspects of particulate air pollution will be obtained by correlating respiratory responses with mass and number concentrations of ambient particles below 0.5 μm.     

Alternatives to the Gravimetric Method for Quantification of Diesel Particulate Matter near the Lower Level of Detection

Abstract

This paper is part of the Journal of the Air & Waste Management Association’s 2010 special issue on combustion aerosol measurements. The issue is a combination of papers that synthesize and evaluate ideas and perspectives that were presented by experts at a series of workshops sponsored by the Coordinating Research Council that aimed to evaluate the current and future status of diesel particulate matter (DPM) measurement. Measurement of DPM is a complex issue with many stakeholders, including air quality management and enforcement agencies, engine manufacturers, health experts, and climatologists. Adoption of the U.S. Environmental Protection Agency 2007 heavy-duty engine DPM standards posed a unique challenge to engine manufacturers. The new standards reduced DPM emissions to the point that improvements to the gravimetric method were required to increase the accuracy and the sensitivity of the measurement. Despite these improvements, the method still has shortcomings. The objectives of this paper are to review the physical and chemical properties of DPM that make gravimetric measurement difficult at very low concentrations and to review alternative metrics and methods that are potentially more accurate, sensitive, and specific. Particle volatility, size, surface area, and number metrics are considered, as well as methods to quantify them. Although the authors believe that an alternative method is required to meet the needs of engine manufacturers, the methods reviewed in the paper are applicable to other areas where the gravi-metric method detection limit is approached and greater accuracy and sensitivity are required. The paper concludes by suggesting a method to measure active surface area, combined with a method to separate semi-volatile and solid fractions to further increase the specificity of the measurement, has potential for reducing the lower detection limit of DPM and enabling engine manufacturers to reduce DPM emissions in the future.     

Recent Changes in Body Size of the Eurasian Otter <Emphasis Type="Italic">Lutra lutra</Emphasis> in Sweden

We studied geographical and temporal body size trends among 169 adult museum specimens of the Eurasian otter (Lutra lutra) collected in Sweden between 1962 and 2008, whose sex, year of collection, and locality were known. Skull size and body mass increased significantly in relation to the year of collection, and skull size (but not body mass) was significantly and negatively related to latitude, contrasting Bergmann’s rule and the trend found for Norwegian otters. Latitudinal differences in body size between the two countries may be due to differences in food availability. The temporal increase in body size among Swedish otters resembled that observed for Norway otters, though Swedish otters are smaller with respect to their Norwegian counterparts. Latitude and year represent a combination of environmental factors, including ambient temperature in the year of collection as well as the number of days of ice coverage. We replaced the above factors with mean annual temperature or the number of days of ice coverage, and found that each of these factors explains a similar proportion of the variation in body size as did latitude and year. We hypothesize that this temporal increase in body size is related to a combination of factors, including reduced energy expenditure resulting from increasing ambient temperature, and increased food availability from longer ice-free periods.     

Influence of nozzle type upon the control of the stalkborer using chlorpyrifos and cyfluthrin 1

Abstract

Field experiments were conducted in corn plots during 1988 that were artificially Infested with stalkborers, Papianema nebris (Guenee'). Two atomizers, a flatfan and a flood nozzle chosen for different droplet size distributions were used to apply two insecticides, chlorpyrifos and cyfluthrin at two application rates. Nozzles, insecticides, rates, and associated interactions were evaluated for control of stalkborer in the field. Laboratory studies involved application of insecticides to soil and glass via a spray track for bioassay at field application rates. Image analysis of percent area travelled on water sensitive paper by stalkborers was compared to droplet percent area covered to obtain percent area contacted per insect. Droplet size distributions for each nozzle were obtained using an Aerometrics particle sizing instrument. Significant differences in stalkborer control were attributed to percent area covered by smaller droplets measured by image analysis.     

Optimization and characterization of the formation of oil-in-water diazinon nanoemulsions: Modeling and influence of the oil phase,surfactant and sonication

Nanoemulsions are particularly suitable as a platform in the development of delivery systems for lipophilic functional agents. Current research describes the formation of oil-in-water (O/W) diazinon nanoemulsions using synthetic and natural additives by adopting a high-energy (ultrasound) emulsification method. The diazinon nanoemulsions were spontaneously formed by adding dropwise a mixture of diazinon, solvent and co-solvent in an aqueous solution containing a surfactant (tween or lecithin) with continuous stirring. The nanoemulsions were then formed by ultra-sonication. The effects of three levels of active ingredient, solvent, co-solvent, surfactant, sonication time and sonication cycle and power were performed by Minitab software to design the experiment. Effects of these factors on droplet size, polydispersity index (PDI), viscosity and pH of nanoemulsions were investigated. The results of the modeling showed that the experimental data could be adequately adapted in a second-order polynomial model with a multiple regression coefficient r² of 0.821 for the prediction of particle size, PDI and viscosity. The long-term and thermodynamic stability of the prepared nanoemulsions were tested. The droplet size and morphology of the nanoemulsions were measured by dynamic light scattering (DLS) and transmission electron microscopy (TEM). On this basis, a water-insoluble insecticide diazinon was incorporated into 26 optimized nanoemulsion systems to demonstrate potential applications in pest control. The results of DLS and TEM measurements showed that most of prepared nanoemulsions had an almost monodisperse droplet size distribution (PDI < 200 nm). Incorporation of diazinon had no significant effect on the size and stability of the nanoemulsions and the formulated nanoemulsion remained stable after four months of storage.     

People and biodiversity in the 21st century: This article belongs to Ambio’s 50th Anniversary Collection. Theme: Biodiversity conservation

Fifty years have elapsed since the first publication of Ambio. Throughout this period, fundamental changes have occurred in societal attitudes to biodiversity conservation. Ambio has published numerous papers that have aligned with these new approaches. High citations numbers suggest that Ambio papers have had a significant impact on conservation strategies. We review these publications and find that they align well with changed societal perspectives on biodiversity. Ambio papers have called for greater contributions of local and indigenous peoples and for conservation in multi-functional landscapes. The 1992 Convention on Biological Diversity built on these principles. Negotiations are now underway for a post-2020 framework for biodiversity. Ambio papers have argued for a stronger scientific basis for conservation and for the need to adapt to changing conditions and to the rich diversity of societal preferences for conservation. International processes favor simple, generalizable approaches to conservation but we call for recognition of the diversity of ecological and human conditions in which conservation occurs. There is a need to build capacity to support a diversity of conservation approaches that are adapted to changing local conditions and to the priorities of diverse human societies.     

The Number-Size Distribution of Atmospheric Particles During Temperature Inversions

Instruments capable of measuring in situ numbers of particles within specific size ranges covering a particle-diameter spectrum of approximately 0.001 – 10 microns have been employed to continuously monitor the concentration and size-distribution of atmospheric aerosols. The monitoring site was a television tower located on the boundary between Minneapolis and St. Paul, Minnesota. Air samples were drawn from 70, 170, and 500 feet above ground level and analyzed with optical, electrical, and condensation particle counters to obtain a number-size distribution within the 0.001 – 10 micron size range. In addition to the measurement of particle number and size, several micrometeorological parameters were simultaneously monitored. Particle number-size distributions which were measured during periods of temperature inversion are reported     

Heterogeneity of sorption and transport-related properties in a sand–gravel aquifer at Columbus, Mississippi

Properties related to sorption and transport of organic compounds have been determined on 126 sections of 17 cores taken in an aquifer at Columbus Air Force Base in Columbus, MS. Each core section was homogenized prior to analysis. Organic carbon content (OC), specific surface area (SA), distribution coefficient (K_d) for naphthalene, and particle size distribution were measured on each section. Hydraulic conductivity (K_h) for each section was calculated from the particle size distributions. K_h values obtained were comparable with those from earlier borehole flowmeter and pulse tracer tests. Frequency distributions for all properties were lognormal. The arithmetic means and standard deviations for all samples are: OC=0.028% (+0.031, −0.015), SA=4.02 m²/g (+3.95, −1.99), K_d=0.198 l/kg (+0.195, −0.098), K_h=0.00033 m/s (+0.00051, −0.00020). These standard deviations are asymmetrical about the mean because statistics were calculated using log-transformed data, and antilogarithms then taken to obtain the results in the units of property measurement. Variabilities, expressed as coefficients of variation, were similar for all properties. Correlations between the properties were investigated. A good correlation between naphthalene K_d and OC (r=0.78) was found, and other correlations were weak, thus indicating that organic carbon content may control sorption of nonpolar organic solutes in this low carbon aquifer. Autocorrelation (variogram) analysis indicated that, for all properties, correlation lengths were less than the distance between sample points, which were separated by about 20 m horizontally and 1 m vertically. Separate statistical analysis of two widely separated groups of wells showed the groups similar in all properties, except organic carbon. Large-scale inhomogeneity was not detected, although earlier tracer tests produced irregular plumes indicating inhomogeneity in observed solute transport. Implications of the results to site characterization, in situations where aquifers are heterogeneous on short length scales, are discussed.     

Aerosol Aerodynamic Size Conventions For Inertia! Sampler Calibration

The body of information presented in this paper is directed to investigators using inertial samplers for precise and accurate studies of respirable aerosols. The conventions commonly used for aerodynamic size for aerosol particles are discussed including the definition popularized by the "Task Group on Lung Dynamics" of the ICRP, and the "Lovelace" definition. To emphasize the distinction, the Task Group definition (unit density sphere equivalent) is called the aerodynamic equivalent diameter, D_ae, and the Lovelace definition (characteristic expression based upon viscous resistance) is called the aerodynamic resistance diameter, D_ar. The implications and efficacy of these conventions are related to procedures for calibration of cascade impactors, cyclones, and spiral centrifuges. The calibration of a spiral centrifuge at different altitudes is used as an example of the potential problems associated with the use of the different conventions for describing aerodynamic size. The aerodynamic resistance diameter is recommended for calibration of inertial samplers to be used to collect aerosols in the respirable size range.     

Predicting Ringelmann Number and Optical Characteristics of Plumes

Methods have been developed for calculating the Ringelmann number, opacity, and other optical characteristics of stack plumes from information on particulate properties, concentrations, and system geometry. Such calculations can be used in selecting clean-up equipment to improve stack appearance required to meet Ringelmann number and opacity pollution regulations. Methods were developed for white plumes caused by water drops or crystalline material and for black plumes containing carbon emissions. The Mie theory of light scattering was utilized to calculate plume optical properties which were related to Ringelmann number through psycophysically significant correlations. A computer program was written to perform the Mie theory and related calculations. Graphical methods were developed for plumes with log-probability size distributions composed of water drops, dusts with refractive index of 1.50 or carbon type emissions of refractive index 1.59-0.66i. Agreement of Ringelmann numbers predicted by these techniques and those observed for large stacks is excellent.