Applicability of the Mass Concentration Standards for Particulate Matter in Alaskan Areas

The so-called “Six Month Study” of the air toxics problem in the United States was initiated in November 1983 by the U.S. Environmental Protection Agency. The study focused on the magnitude, nature, and distribution of the problem—three major issues that were felt to be most useful to policy makers as they attempted to define the scope and direction of a national program for controlling toxic air pollutants. The following paper is based on a draft staff report on the study released for review in September 1984. The report has not been formally released by the U.S. EPA; a final report is due by late spring of 1985.     

Short Term Air Quality Standards for Suspended Particulate Matter in New York State

The Clean Air Act of 1970 requires each state to submit plans for implementation, maintenance, and enforcement of national ambient air quality standards subsequent to promulgation. Such plans have been geared to meet annual averages and maximum values. Based on experience in implementing the abatement plan it was found that air quality standards for averaging times shorter than one year are needed to shorten the time required to show contravention and to provide a basis for early corrective measures to regulate specific sources. This paper reports on the need and procedures used by New York State to develop such standards for suspended particulates. Daily suspended particulate data were analyzed by the Kolmogorov-Smirnov method goodness of fit technique to determine that the form of the distribution was log normal. A method developed by Larsen for predicting short term maximum concentrations for log normally distributed data was used to determine numerical values for one, two, and three month standards. Monthly, bi-monthly, and tri-monthly suspended particulate standards of 130, 110, and 100 µg/m³, respectively are proposed for the most extensively developed areas of New York State and correspondingly lower values for other areas. The methods used in this development are generally applicable to other air contaminants.     

Demonstrating Attainment of the Air Quality Standards: Integration of Observations and Model Predictions into the Probabilistic Framework

ABSTRACT

This paper introduces an integrated observational-modeling approach to transform the deterministic nature of attainment demonstrations of the National Ambient Air Quality Standard (NAAQS) into the probabilistic framework. While the methods presented here can be used to address any air quality standard that is based on extreme values, this paper focuses on the application to the 1-hr and 8-hr NAAQS for ozone. Extreme value statistics and resampling techniques are applied to estimate the probability of exceeding the NAAQS for both 1-hr and 8-hr ozone concentrations. Within the integrated observation-modeling analysis approach, we show that the model-to-model differences in the predicted responses to emission reductions are smaller than the model-to-model differences in predicted absolute ozone concentrations. We illustrate that the emission reductions stemming from a real-world emission control strategy would substantially reduce the probability of exceeding the NAAQS over a large portion of the eastern United States, especially for the 8-hr average ozone concentrations.     

Low-Wind/High Particulate Matter Episodes in the Calexico/Mexicali Region

Abstract

The U.S. Environmental Protection Agency (EPA) currently classifies Imperial County, CA, as a nonattainment area for PM₁₀ (particulate matter [PM] ≤ 10 μm in diameter), and this region suffers from high rates of chronic bronchitis and childhood asthma. Although high annual and daily average PM levels can have negative health and economic effects, recent studies have identified an association between adverse health effects and short-term PM spikes of tens of micrograms per cubic meter. This study identified PM episodes in Calexico/Mexicali that involve PM concentration spikes with concentrations up to 10 times greater than those reported to cause adverse health effects. These episodes appear to be relatively common during the winter months, are associated with wind speeds below 2 m/sec and stable boundary level heights below 500 m, and can comprise a large portion of the 24-hr PM levels. The organic composition of the PM₁₀ samples collected during the low-wind/high-PM episodes differed from that collected at other times. However, a preliminary source attribution identified only one significant difference between the source classes: agricultural burning accounted for 6.7% of organic-fraction PM₁₀ for low-wind/high-PM episodes versus 0.25% at other times. This preliminary source attribution also revealed that motor vehicles were the most important relative contributor to organic PM₁₀.     

Measurement of Opacity and Particulate Emissions with an On-Stack Transmissometer

An on-stack transmissometer system which is designed to provide a precision measurement of the opacity of visible emissions is described. The sources of error in opacity measurements with regard to recent EPA emission monitoring requirements and planned specifications are discussed. Sources of error are voltage changes, temperature changes, light source and detector aging and effects of ambient light. Other major operational errors are caused by alignment drift and soiling drift. The methods employed to minimize these errors achieve an accuracy of ±3% of span and a maintenance free operational period of 3 months. The relationships between optical density, opacity and transmittance are described. The instrument measurement can be correlated with dust loading provided the particle size distribution is constant. Examples are given of correlations obtained between optical density and particulate concentration in the gas on various types of emission sources and the observed error margins are summarized.     

A Pilot Indoor-Outdoor Study of Organic Particulate Matter and Particulate Mutagenicity

Abstract

Many large metropolitan areas experience elevated concentrations of ground-level ozone pollution during the summertime “smog season”. Local environmental or health agencies often need to make daily air pollution forecasts for public advisories and for input into decisions regarding abatement measures and air quality management. Such forecasts are usually based on statistical relationships between weather conditions and ambient air pollution concentrations. Multivariate linear regression models have been widely used for this purpose, and well-specified regressions can provide reasonable results. However, pollution-weather relationships are typically complex and nonlinear—especially for ozone—properties that might be better captured by neural networks. This study investigates the potential for using neural networks to forecast ozone pollution, as compared to traditional regression models. Multiple regression models and neural networks are examined for a range of cities under different climate and ozone regimes, enabling a comparative study of the two approaches. Model comparison statistics indicate that neural network techniques are somewhat (but not dramatically) better than regression models for daily ozone prediction, and that all types of models are sensitive to different weather-ozone regimes and the role of persistence in aiding predictions.     

宝应县有机农业的发展前景及产业化开发

经对宝应县的有机农业发展现状及相关要素的分析,研究了宝应县有机农业的产业化开发问题。通过对国内外有机农业的发展现状及市场前景的分析,指出发展有机农业具有广阔的前景。同时指出,宝应县发展有机农业的意义;发展有机农业过程中存在的困难和问题,并提出发展宝应县有机农业的七条建议。经研究表明,宝应县发展有机农业具有广阔的发展空间和市场前景,而且宝应县有条件、有基础、也有能力推进有机农业的产业化开发。     

Analysis of an APCA Baghouse Operation and Maintenance Survey

Baghouse operation and maintenance is probably the most serious problem area of fabric filter operations. Committee TC-1 (Particulates) of the Air Pollution Control Association recently surveyed baghouse installations in'the United States for the purpose of gathering information on operation and maintenance procedures and problems. One hundred thirty-three questionnaires were completed and returned. In this paper, the results of a comprehensive analysis of these data are described and interpreted. A multiple-choice type of compilation of the responses has been used to permit statistical interpretation of the results. Due to the length of the questionnaire and the tables which resulted from the analysis, these are described but not included in the following paper. They are available from the TC-1 Committee c/o APCA.     

A Comparative Study of Environmental Tobacco Smoke Particulate Mass Measurements in an Environmental Chamber

Particulate mass concentration measurements have been made on environmental tobacco smoke (ETS) for the purpose of assessing the relative accuracy of several measurement procedures. ETS over a range of concentrations was generated in an environmental chamber by three methods. Mass concentration was measured by a gravimetric/spectrophotometric collection procedure, piezoelectric particle mass monitors, two nephelometry-based mass monitors, and a particle counting and sizing system. Two-hour average mass concentrations were determined by each method for concentrations ranging from very low levels up to those achieved by smoking one entire cigarette in the chamber. Statistical comparisons were made among procedures employing the gravimetric filter measurement as the basis for comparison. One nephelometry-based procedure gave significantly higher and the other significantly lower values than the filter determination. In one case, a correction for the difference between the particle mass density of the calibrating aerosol and that of ETS brought the nephelometry-based procedure into reasonable agreement with the filter measurement, while for the other, the correction did not resolve the discrepancy between methods. Statistically significant differences between the responses of two supposedly identical piezoelectric mass monitors were found, as was some slight dependence of the nephelometry- based procedures on method of ETS generation. In summary, the results indicate that significant errors can be expected if the instruments studied are used “off the shelf,” even for ETS generated under controlled laboratory conditions. Caution should be employed in field measurements where numerous sources and types of particulate matter can be encountered.     

The Impact of a Building Implosion on Airborne Particulate Matter in an Urban Community

Abstract

In response to community concerns, the air quality impact of imploding a 22-story building in east Baltimore, MD, was studied. Time- and space-resolved concentrations of indoor and outdoor particulate matter (PM) (nominally 0.5–10 µm) were measured using a portable nephelometer at seven and four locations, respectively. PM₁₀ levels varied in time and space; there was no measurable effect observed upwind of the implosion. The downwind peak PM₁₀ levels varied with distance (54,000–589 µg/m³) exceeding pre-implosion levels for sites 100 and 1130 m 3000- and 20-fold, respectively. Estimated outdoor 24-hr integrated mass concentrations varied from 15 to 72 µg/m³. The implosion did not result in the U.S. Environmental Protection Agency (EPA) National Ambient Air Quality Standard (NAAQS) for PM₁₀ being exceeded. X-ray fluorescence analysis indicated that the elemental composition was dominated by crustal elements: calcium (57%), silicon (23%), aluminum (7.6%), and iron (6.1%). Lead was above background but at a low level (0.17 µg/m³). Peak PM₁₀ concentrations were short-lived; most sites returned to background within 15 min. No increase in indoor PM₁₀ was observed even at the most proximate 250 m location. These results demonstrate that a building implosion can have a severe but short-lived impact on community air quality. Effective protection is offered by being indoors or upwind.     

Characterization of Particulate Matter in California

ABSTRACT

The size, composition, and concentration of particulate matter (PM) vary with location and time. Several monitoring/sampling programs are operated in California to characterize PM less than 2.5 and 10 µm in aerodynamic diameter (PM_2.5 and PM₁₀). This paper presents a broad summary of the spatial and temporal variations observed in ambient PM_2.5 and PM₁₀ concentrations in California. Many areas that have high PM₁₀ concentrations also have relatively high PM_2.5 concentrations, and data indicate that a significant portion of the PM₁₀ air quality problem is caused by PM_2.5. To develop effective plans for attaining the ambient PM standards, improved understanding of these unique problems is needed. Since 1989, pollution control efforts—whether specifically targeted for particulate matter or indirectly via controls on gaseous emissions—have caused annual average PM_2.5 and PM₁₀ concentrations to decline at most sites in California.     

Particulate matter sources on an hourly timescale in a rural community during the winter

Particulate matter (PM) sources at four different monitoring sites in Alexandra, New Zealand, were investigated on an hourly timescale. Three of the sites were located on a horizontal transect, upwind, central, and downwind of the general katabatic flow pathway. The fourth monitoring site was located at the central site, but at a height of 26 m, using a knuckleboom, when wind conditions permitted. Average hourly PM₁₀ (PM with an aerodynamic diameter <10 μm) concentrations in Alexandra showed slightly different diurnal profiles depending on the sampling site location. Each location did, however, feature a large evening peak and smaller morning peak in PM₁₀ concentrations. The central site in Alexandra experienced the highest PM₁₀ concentrations as a result of PM transport along a number of katabatic flow pathways. A significant difference in PM₁₀ concentrations between the central and elevated sites indicated that a shallow inversion layer formed below the elevated site, limiting the vertical dispersion of pollutants. Four PM₁₀ sources were identified at each of the sites: biomass combustion, vehicles, crustal matter, and marine aerosol. Biomass combustion was identified as the most significant source of PM₁₀, contributing up to 91% of the measured PM₁₀. Plots of the average hourly source contributions to each site revealed that biomass combustion was responsible for both the evening and morning peaks in PM₁₀ concentrations observed at each of the sites, suggesting that Alexandra residents were relighting their fires when they rose in the morning. The identification of PM sources on an hourly timescale can have significant implications for air quality management.

Implications: Monitoring the sources of PM₁₀ on an hourly timescale at multiple sites within an airshed provides extremely useful information for air quality management. Sources responsible for observed peaks in measured diurnal PM₁₀ concentration profiles can be easily identified and targeted for reduction. Also, hourly PM₁₀ sampling can provide crucial information on the role meteorology plays in the development of elevated PM₁₀ concentrations.     

Evaluation of an Offline Method for the Analysis of Atmospheric Reactive Gaseous Mercury and Particulate Mercury

Abstract

Reactive gaseous mercury (RGM) and particulate mercury (PHg) were collected in Milwaukee, WI, between April 2004 and May 2005, and in Riverside, CA, between July 25 and August 7, 2005 using sorbent and filter substrates. The substrates were analyzed for mercury by thermal desorption analysis (TDA) using a purpose-built instrument. Results from this offline-TDA method were compared with measurements using a real-time atmospheric mercury analyzer. RGM measurements made with the offline-TDA agreed well with a commercial real-time method. However, the offline TDA reported PHg concentrations 2.7 times higher than the real-time method, indicating evaporative losses might be occurring from the real-time instrument during sample collection. TDA combined with reactive mercury collection on filter and absorbent substrates was cheap, relatively easy to use, did not introduce biases due to a semicontinuous sample collection strategy, and had a dynamic range appropriate for use in rural and urban locations. The results of this study demonstrate that offline-TDA is a feasible method for collecting reactive mercury concentrations in a large network of filter-based samplers.     

Particulate and Nicotine Sampling in Public Facilities and Offices

Abstract

The purpose of this study was to characterize and measure indoor air quality in public facilities and office buildings. The pollutants of interest were particulate matter smaller than 2.5 μm in diameter, PM-2.5, and environmental tobacco smoke (ETS). Integrated PM- 2.5 samples were taken on Teflon membrane filters using Harvard Aerosol Impactors as a pre-size selector. Filters were analyzed by gravimetric analysis. Nicotine, which was used as a marker for ETS, was collected on sodium-bisulfate-impregnated, glass-fiber filters and was analyzed by gas chromatography. Twenty-one structures were monitored in Metropolitan Boston. Measured particle concentrations ranged from 6.0 μg/m³ to about 550 μg/m³. Nicotine concentrations were as high as 26 μg/m³ in a designated smoking room. Real-time measurements were also taken using two types of nephelometers; a Handheld Aerosol Monitor (HAM) and a Miniature Real-Time Aerosol Monitor (MINIRAM). Short-term field measurements with these instruments correlated better with the integrated PM-2.5 concentrations in smoking locations than with concentrations in non-smoking areas.     

Spatial Variability of Different Fractions of Particulate Matter within an Urban Environment and between Urban and Rural Sites

ABSTRACT

The spatial variability of different fractions of particulate matter (PM) was investigated in the city of Basel, Switzerland, based on measurements performed throughout 1997 with a mobile monitoring station at six sites and permanently recorded measurements from a fixed site. Additionally, PM₁₀ measurements from the following year, which were concurrently recorded at two urban and two rural sites, were compared.

Generally, the spatial variability of PM₄, PM₁₀, and total suspended particulates (TSP) within this Swiss urban environment (area = 36 km²) was rather limited. With the exception of one site in a street canyon next to a traffic light, traffic density had only a weak tendency to increase the levels of PM. Mean PM₁₀ concentration at six sites with different traffic densities was in the range of less than ±10% of the mean urban PM₁₀ level. However, comparing the mean PM levels on workdays to that on weekends indicated that the impact of human activities, including traffic, on ambient PM levels may be considerable.

Differences in the daily PM₁₀ concentrations between urban and more elevated rural sites were strongly influenced by the stability of the atmosphere. In summer, when no persistent surface inversions exist, differences between urban and rural sites were rather small. It can therefore be concluded that spatial variability of annual mean PM concentration between urban and rural sites in the Basel area may more likely be caused by varying altitude than by distance to the city center.     

Attainment Flip-Flops and the Achievability of the Ozone Air Quality Standard

Abstract

This paper presents the results of the first reported study on fine particulate matter (PM) chemical composition at Salamanca, a highly industrialized urban area of Central Mexico. Samples were collected at six sites within the urban area during February and March 2003. Several trace elements, organic carbon (OC), elemental carbon (EC), and six ions were analyzed to characterize aerosols. Average concentrations of PM with aerodynamic diameter of less than 10 μm (PM₁₀) and fine PM with aerodynamic diameter of less than 2.5 μm (PM_2.5) ranged from 32.2 to 76.6 μg m^-3 and 11.1 to 23.7 μg m^-3, respectively. OC (34%), SO₄ ⁼ (25.1%), EC (12.9%), and geological material (12.5%) were the major components of PM_2.5. For PM₁₀, geological material (57.9%), OC (17.3%), and SO₄ ⁼ (9.7%) were the major components. Coarse fraction (PM₁₀ –PM_2.5), geological material (81.7%), and OC (8.6%) were the dominant species, which amounted to 90.4%. Correlation analysis showed that sulfate in PM_2.5 was present as ammonium sulfate. Sulfate showed a significant spatial variation with higher concentrations to the north resulting from predominantly southwesterly winds above the surface layer and by major SO₂ sources that include a power plant and refinery. At the urban site of Cruz Roja it was observed that PM_2.5 mass concentrations were similar to the submicron fraction concentrations. Furthermore, the correlation between EC in PM_2.5 and EC measured from an aethalometer was r² = 0.710. Temporal variations of SO₂ and nitrogen oxide were observed during a day when the maximum concentration of PM_2.5 was measured, which was associated with emissions from the nearby refinery and power plant. From cascade impactor measurements, the three measured modes of airborne particles corresponded with diameters of 0.32, 1.8, and 5.6 μm.     

Particulate matter and manganese exposures in Toronto,Canada

Methylcyclopentadienyl manganese tricarbonyl (MMT) is a manganese-based gasoline additive used to enhance automobile performance. MMT has been used in Canadian gasoline for about 20 yr. Because of the potential for increased levels of Mn in particulate matter resulting from automotive exhausts, a large-scale population-based exposure study (∼1000 participant periods) was conducted in Toronto, Canada, to estimate the distribution of 3-day average personal exposures to particulate matter (PM_2.5 and PM₁₀) and Mn. A stratified, three-stage, two-phase probability, longitudinal sample design of the metropolitan population was employed. Residential indoor and outdoor, and ambient levels (at a fixed site and on a roof) of PM_2.5, PM₁₀, and Mn were also measured. Supplementary data on traffic counts, meteorology, MMT levels in gasoline, personal occupations, and activities (e.g. amount of vehicular usage) were collected. Overall precision (%RSD) for analysis of duplicate co-located samples ranged from 2.5 to 5.0% for particulate matter and 3.1 to 5.5% for Mn. The detection limits were 1.47 and 3.45 μg m^-3 for the PM₁₀ and PM_2.5 fractions, respectively, and 5.50 and 1.83 ng m^-3 for Mn in PM₁₀ and PM_2.5, respectively. These low detection limits permitted the reporting of concentrations for >98% of the samples. For PM₁₀, the personal particulate matter levels (median 48.5 μg m^-3) were much higher than either indoor (23.1 μg m^-3) or outdoor levels (23.6 μg m^-3). The median levels for PM_2.5 for personal, indoor, and outdoor were 28.4, 15.4 and 13.2 μg m^-3, respectively. The correlation between PM_2.5 personal exposures and indoor concentrations was high (0.79), while correlations between personal and the outdoor, fixed site and roof site were low (0.16–0.27). Indoor Mn concentration distributions (in PM_2.5 and PM₁₀), unlike particulate matter, exhibited much lower and less variable levels that the corresponding outdoor data. The median personal exposure was 8.0 ng m^-3, compared with 4.7 and 8.6 ng m^-3, respectively, for the indoor and outdoor distributions. The highest correlations occurred for personal vs indoor data (0.56) and for outdoor vs roof site data (0.66), and vs fixed site data (0.56). The concentration of Mn in particulate matter, expressed in ppm (w/w), revealed that the fixed site was the highest, followed by the roof site, outdoor, indoor, and personal. The personal and indoor data showed a statistically significant correlation (0.68) while all other correlations between personal or indoor data and outdoor or fixed-site data were quite small. The low correlations of personal and indoor levels with outdoor levels suggest that different sources in the indoor and outdoor microenvironments produce particle matter with dissimilar composition. The correlation results indicate that neither the roof- nor fixed-site concentrations can adequately predict personal particulate matter or Mn exposures.     

Altitude-dependent wet,dry and occult nitrogen deposition in an Alpine Region

From November 1995 to October 1996 and from October 1997 to September 1998, samples of wet precipitation, cloud water, as well as of reactive gases and particulate matter, were collected at three elevational levels (920 m, 1280 m and 1758 m a.s.l.) in Achenkirch, Austria. The samples were analysed for ammonium and nitrate in wet precipitation and in cloud water, for ammonia, nitric acid and nitrogen dioxide in the gas phase and for particulate ammonium and particulate nitrate in aerosol. Total nitrogen deposition was calculated combining measured concentrations in wet, dry and occult depositions with the corresponding deposition fluxes. Two multilayer deposition models were used for the calculation of dry and occult deposition. The total nitrogen input in 1995/96 was estimated to be 29 kg N ha⁻¹a⁻¹ at the Christlumkopf station (1758 m), 20 kg N ha⁻¹a⁻¹ at the Christlumalm station (1280 m) and 28 kg N ha⁻¹a⁻¹ at the Talboden station (930 m). Respective data for the 1997/98 observation period were 31 kg N ha⁻¹a⁻¹ at the Christlumkopf station (1758 m) and 18 kg N ha⁻¹a⁻¹ at the Mühleggerköpfl station (920 m). Critical Loads of nitrogen for coniferous forests were exceeded significantly near-source regions represented by areas of intense agricultural use and at high elevation sites.