长江经济带工业来源危险废物污染与处理特征分析及监管对策建议

依据2017年环境统计数据, 分析了长江经济带工业危险废物的污染及处理特征:长江经济带危废产生 量较大的省份是江苏、浙江、云南、湖南和四川;危废种类主要是来源于化工、钢铁、有色和造纸行业的废酸、有色金属冶炼废物、废碱和焚烧处置残渣;各地对危废的处理情况各有优劣。根据以上特征,提出加强对重点 区域的监管和调度,针对特定行业和危废种类,建议出台最佳可行的处理技术,建立区域之间危废管理大平台,促进区域危废处理优势互补和均衡发展,挖掘企业自行处理能力,减轻危废集中处理压力。     

Monitoring quantity and characteristics of municipal solid waste in Dhaka City

A reliable estimate of the quantity of solid waste generation in the city is very important for proper solid waste planning and management. However, reported estimates of solid waste generation vary widely and lead to questionability. The reported values have been derived on the assumption of demography, standard rate of waste generation by households, density values, number of trucks engaged for waste transportation and monitoring of truck movement at dump sites, etc. This diverse nature of the available data and the question of accuracy necessitate a rigorous study that has tried to document the waste quantity in the recently formulated master plan of Dhaka City. The socio-economic parameters, behavioral characteristics, generation sources, seasonality, and per capita growth rate are considered in estimating the waste quantity along with its future projections. The findings from the estimation of waste quantities state that seasonal differences in the municipal solid waste stream are not substantial. The most seasonably variable material in the municipal solid waste stream is food waste. Residential waste is relatively homogeneous. Although there are some differences in waste generation depending on demographic and other local factors, most households dispose of essentially similar types of wastes. Variation occurs in waste composition dependent upon income levels and category of sources. Variation also occurs based upon the extent of source reduction and recycling opportunities. As opportunities exist to recycle wastes, the recycling facilities might have to grow at a similar pace to the generation of waste. Physical and chemical characteristics of solid waste are important to implement the waste disposal and management plan for the selection of resource and energy recovery potentials. A number of studies have been conducted to determine the composition of wastes including moisture content and calorific value. The data show that the moisture content in city waste is significantly higher and the calorific value is much lower, which determines the viability of composting or anaerobic digestions rather than waste combustion.     

Opportunities for Improved Risk Assessments of Exotic Species in Canada Using Bioclimatic Modeling

This paper briefly reviews the process of exotic pest risk assessments and presents some examples of emerging opportunities for spatial bioclimatic modeling of exotic species in Canada. This type of analysis can support risk assessments but does not replace the need for on-going high quality field-based observations to validate and update models. Bioclimatic analysis of several exotic pests is provided to illustrate both opportunities and limits. A link is demonstrated to the National Forest Inventory to characterize timber volumes at risk for one exotic species. Challenges' are both scientific and administrative. More accessible and current field survey data are required to improve models. Our experience is that for many exotic species, historical, and even current, data are not always digital or quality controlled for taxonomic identity and accurate geo-referencing. This inhibits their use for integrated spatial modeling applications.     

Non-radiological contaminants from uranium mining and milling at Ranger,Jabiru, Northern Territory,Australia

Protection from the hazards from radioactivity is of prime importance in the management of uranium mine and mill wastes. Such wastes also contain non-radiological contaminants (heavy metals, acids and neutralising agents) which give rise to potential long-term health and environmental hazards and short-term hazards to the aquatic ecosystem, e.g. as a result of release of waste water. This study seeks to identify non-radiological contaminants (elements) transferred to waste water at the Ranger uranium mine/mill complex at Jabiru, which are likely to hazardous to the aquatic environment. The two principal sources of contaminants are:

1. ore and waste rock mobilised from mining; and
2. process reagents used in the milling and mineral extraction process.

These substances may or may not already be present in the natural environment but may lead to deleterious effects on the aquatic environment if increased above threshold levels. Rhenium, derived from the ore body, was found to be significantly enriched in waste water from Ranger, indicating its suitability as an indicator element for water originating from the mining and milling process, but only uranium, likewise derived from the ore, and magnesium, manganese and sulfur (as sulfate) from the milling process were found to be significant environmental contaminants.     

Measuring waste generation in third world cities: A case study of Ilorin,Nigeria

Problems associated with urban wastes are now at crisis stage in Nigeria. All efforts made to solve the problems have failed, as the efforts were directed towards instant cleaning rather than long lasting programs to cope with problems associated with environmental sanitation. Measurements were taken of the domestic waste generated by randomly selected households in Ilorin, to predict the generation rate for the city. The data was subjected to various analyses. The models used in developed nations were found inappropriate to predict the waste generation rate of the people at Ilorin because of cultural factors. Various methods to cope with the environmental sanitation problems of cities of developing areas were then suggested.     

中国固体废物的环境管理与环境监测技术现状

为加强中国固体废物的环境管理和环境监测技术,回顾了中国自１９８５年以来制定的固体放心物环境管理法规制度以及１９８４年至１９９８年颁布的２０多年家或行业的固体废物处置标准体系等固体废物的环境管理状况,着重论述了中国固体废物环境监测技术的发展历史与现状。指出经过２０多年的努力,在固体废物环境监测技术与方法上初步形成了该领域框架体系,有固体废物的采样与制样技术;危险废物的有害特性试验鉴别方法,固体废物具     

Monitoring the biotic aspects of our environment as a policy instrument

As all environmental programs also programs monitoring the biotic aspects of our environment (dealt with in this article) should contribute to a more effective and efficient environmental policy. These programs have to function therefore (as no other type of environmental information does, according to the authors) as cheap and efficient early warning and early control systems, providing decision makers with important and reliable monitoring results.How these monitoring programs should function in the decision making process is illustrated in abstract in this article by a simple control system with feedback (as shown in Figures 1, 2 and 3).The monitoring programs dealt with in this article should enable us to detect and forecast changes in the most important biotic aspects of our environment and-by continuous monitoring-to control whether the use of policy instruments has been effective or not in averting or diminishing unwanted changes (problems).Two options of decision makers with respect to monitoring results are shown (either to disregard unwanted changes as a problem or to accept these changes as a problem and to do something about them). To contribute to an effective and efficient environmental policy monitoring results therefore have to be important and reliable enough to react upon.The question is raised which biotic aspects in our environment are (or have to be considered as) important (because of their own value, as indicators and/or as biotic conditions) and how reliable monitoring results can (have to) be obtained.It is discussed how environmentalists could try to make it more difficult for decision makers to duck the problems (by monitoring only important aspects and by using only perfectly clear targets and standards) and how they could try at the same time to make it easier for them to take action (by setting up integrated environmental monitoring programs in order to find out how desired and undesired changes can be influenced). The role of active publicity is stressed in this connection.     

Geospatial strategy for sustainable management of municipal solid waste for growing urban environment

This paper presents the implementation of a Geospatial approach for improving the Municipal Solid Waste (MSW) disposal suitability site assessment in growing urban environment. The increasing trend of population growth and the absolute amounts of waste disposed of worldwide have increased substantially reflecting changes in consumption patterns, consequently worldwide. MSW is now a bigger problem than ever. Despite an increase in alternative techniques for disposing of waste, land-filling remains the primary means. In this context, the pressures and requirements placed on decision makers dealing with land-filling by government and society have increased, as they now have to make decisions taking into considerations environmental safety and economic practicality. The waste disposed by the municipal corporation in the Bhagalpur City (India) is thought to be different from the landfill waste where clearly scientific criterion for locating suitable disposal sites does not seem to exist. The location of disposal sites of Bhagalpur City represents the unconsciousness about the environmental and public health hazards arising from disposing of waste in improper location. Concerning about urban environment and health aspects of people, a good method of waste management and appropriate technologies needed for urban area of Bhagalpur city to improve this trend using Multi Criteria Geographical Information System and Remote Sensing for selection of suitable disposal sites. The purpose of GIS was to perform process to part restricted to highly suitable land followed by using chosen criteria. GIS modeling with overlay operation has been used to find the suitability site for MSW.     

印染废水处理污泥危险废物鉴别过程中有毒污染物的迁移转化及鉴别因子筛选

简述了印染废水处理污泥危险废物鉴别过程中有毒污染物的迁移转化及鉴别因子筛选。以采用活性染料的印染企业为例,从常用的原辅材料、使用的生产工艺、常用的废水处理工艺等几个方面来对印染废水处理污泥危险废物鉴别过程中有毒污染物的迁移及转化进行分析。提出危险废物鉴别工作任重而道远,危险废物鉴别的关键在于日常监管。     

Accounting embodied economic potential of healthcare waste recycling—a case study from Pakistan

Proper management of healthcare wastes is a key concern across resource-constrained countries in South Asia. Existing scientific research on this topic usually involves epidemiological and behavioral studies. Similarly, environmental impact assessment of healthcare wastes is mainly conducted from an end-user or anthropocentric point of view. In this study, we took a novel approach by analyzing healthcare wastes using an ecocentric position. Here, we utilize a case study of a general public hospital in a major city of Pakistan to analyze the embodied energy of its waste fractions by category. We used Emergy analysis to assess the true economic potential of recycling these waste items. While doing so, we compared the economic potential of current waste recycling practices with the scenario of 100% recycling of useful waste fractions. We discovered that the latent embodied energy of different recyclable waste fractions made them far more valuable than their existing market prices indicate. This value increased further if the useful waste fractions were completely recycled. In conclusion, this study used empirical evidence to argue in favor of source-segregation and recycling of healthcare wastes so that the higher costs associated with natural resource extraction and processing can be avoided. Future studies considering hazardous healthcare wastes can use the approach taken in this paper to analyze the impact of other practical waste treatment procedures.     

Municipal solid waste generation in growing urban areas in Africa: current practices and relation to socioeconomic factors in Jimma, Ethiopia

As one of cities in the developing countries, a rapid population growth and industrial activities pose many environmental challenges for Jimma city, Ethiopia. One aspect of urban growth posing a threat on sustainable development is poor solid waste management, which results in environmental pollution. The purpose of this study is to evaluate the quantity, composition, sources of waste generated, their current disposal practices, and to recommend appropriate management technologies. The total waste generated daily in Jimma city was ca. 88,000 kg, and the average per capita generation rate was 0.55?±?0.17 kg/capita/day. Eighty-seven percent of the waste was produced by households and 13% by institutions, and a negligible fraction (0.1%) was generated by street sweepings. During the rainy season, 40% more waste was generated than in the dry season because of the increased availability of agricultural food product. Further analysis showed that biodegradable organic waste constitutes 54% by weight with an average moisture content of 60% that falls within the required limits for composting. The nonbiodegradable components constitute 46% of which 30% of it was nonrecyclable material. Only 25% of the community uses municipal containers for disposal at the selected landfill site. Fifty-one percent of the households disposed their waste in individually chosen spots, whereas 22% burned their waste. Finally 2% of households use private waste collectors. The socioeconomic analysis showed that higher family income and educational status is associated more with private or municipal waste collection and less with the application of backyard or open dumping. These insights into generated waste and management practice in Jimma city allow making suggestions for improved collection, treatment, and disposal methods. A primary conclusion is that the biodegradable waste is a major fraction having suitable properties for recycling. As such an economic benefit can be obtained from this waste while avoiding the need for disposal.     

Toxicological effects of major environmental pollutants: an overview

The last quarter of the twentieth century had witnessed a global surge in awakening against the unabated menace of environmental pollution. Among the various types of environmental pollution, water pollution is an age-old problem but it has gained an alarming dimension lately because of the problems of population increase, sewage disposal, industrial waste, radioactive waste, etc. Present scenario of water pollution calls for immediate attention towards the remediation and detoxification of these hazardous agents in order to have a healthy living environment. The present communication will deal with the toxicological effects of major environmental pollutants, viz. heavy metals, pesticides, and phenols.     

Multi-level screening of a proposed hazardous waste treatment and disposal facility site--a case study

A comprehensive environmental assessment (EA) is a pre-requisite before the site for developing a hazardous waste treatment and disposal facility (HWTDF) is selected. However, the resource limitations, especially for developing countries, often dictatethat the detailed EA be restricted to those sites, which are constraint free and have low hazard potentials. Thus, a preliminary screening exercise for assessing the suitability ofsite for developing the HWTDF needs to be carried out to avoid huge costs involved in detailed EA. While screening a HWTDF site,various factors such as present land use, ecologically sensitiveareas, geology and hydrogeology of the area, the quality and quantity of wastes, engineered safeguards, and the operationalprocedures that need to be adopted, are required to be addressed. In this paper, a multi-level screening criteria employing RemoteSensing, Constraint Mapping, Groundwater Pollution Potential Index (DRASTIC Index), and the Site Ranking was used to assess the suitability of a proposed site for the development of HWTDF.The study helped to identify various constraints at the proposedsite and their significance on the development of the HWTDF.     

Enumeration of Legionella pneumophila in cooling tower water systems

Legionella pneumophila, the causative agent of Legionnaires disease, is known to colonise and frequently grow in cooling tower waters. Disease is acquired by inhaling aerosol contaminated by legionellae. Determination of the count of Legionella pneumophila in cooling tower waters may, therefore, be useful for risk assessment. In our survey, 103 water samples from 50 cooling towers were examined over a five-year period to indicate the seasonal distribution and the ecology of L. pneumophila, as regards temperature and pH. L. pneumophila serogroup 1 was found in 44% of the isolated strains, which is primarily responsible for the majority of Legionnaires disease. The large majority of examined towers had levels of L. pneumophila in the high-risk category. These cooling towers have been linked to many outbreaks of Legionnaires disease.     

东莞市城市功能区噪声自动监测点位布设初探

依据功能区环境噪声普查数据和城市环境噪声功能区分布特征,进行环境噪声自动监测点位布设.研究的原则和方法,对环境噪声自动监测点位选取具有一定的参考价值和指导意义.     

Application of analytic hierarchy process in a waste treatment technology assessment in Mexico

The high per capita generation of solid waste and the environmental problems in major rural communities of Ensenada, Baja California, have prompted authorities to seek alternatives for waste treatment. In the absence of a selection methodology, three technologies of waste treatment with energy recovery (an anaerobic digester, a downdraft gasifier, and a plasma gasifier) were evaluated, taking the broader social, political, economic, and environmental issues into considerations. Using the scientific literature as a baseline, interviews with experts, decision makers and the community, and waste stream studies were used to construct a hierarchy that was evaluated by the analytic hierarchy process. In terms of the criteria, judgments, and assumptions made in the model, the anaerobic digester was found to have the highest rating and should consequently be selected as the waste treatment technology for this area. The study results showed low sensitivity, so alternative scenarios were not considered. The methodology developed in this study may be useful for other governments who wish to assess technologies to select waste treatment.     

Assessment of plastic waste generation and its potential recycling of household solid waste in Can Tho City, Vietnam

Plastic solid waste has become a serious problem when considering the disposal alternatives following the sequential hierarchy of sound solid waste management. This study was undertaken to assess the quantity and composition of household solid waste, especially plastic waste to identify opportunities for waste recycling. A 1-month survey of 130 households was carried out in Can Tho City, the capital city of the Mekong Delta region in southern Vietnam. Household solid waste was collected from each household and classified into ten physical categories; especially plastic waste was sorted into 22 subcategories. The average household solid waste generation rate was 281.27 g/cap/day. The compostable and recyclable shares respectively accounted for high percentage as 80.74% and 11%. Regarding plastic waste, the average plastic waste generation rate was 17.24 g/cap/day; plastic packaging and plastic containers dominated with the high percentage, 95.64% of plastic waste. Plastic shopping bags were especially identified as the major component, accounting for 45.72% of total plastic waste. Relevant factors such as household income and household size were found to have an existing correlation to plastic waste generation in detailed composition. The household habits and behaviors of plastic waste discharge and the aspects of environmental impacts and resource consumption for plastic waste disposal alternatives were also evaluated.     

Incineration of hazardous wastes

Glaxo has practiced incineration of liquid and gaseous wastes for over twenty years and currently operate eleven liquid and gas incinerators in the United Kingdom and Singapore. The liquid incinerators burn, as their main streams, those solvents that cannot be recovered and recycled within the processes. The early installations were for readily combustible solvents only. However, there has been a progressive move into the destruction of more difficult and hazardous wastes, with the consequential requirements for more sophisticated technology, in the belief that the responsible destruction of waste should be tackled near to its source. The eventual aim is to be self-sufficient in this area of waste management. The incineration of hazardous liquid and gaseous waste has presented a series of design, operational and monitoring problems into account which have all been successfully overcome. The solutions take into account the environmental consequences of the operations from both liquid and gaseous emissions. In order to ensure minimal environmental impact and safe operation the best practicable technology is employed. Environmental assessment forms part of the process development and permitting procedures.Plenary speaker.     

A Routing and Scheduling System for Infectious Waste Collection

Most hospitals and clinics in Taiwan do not have on-site treatment facilities for their infectious waste and must rely on outside agencies for their collection and treatment. The problem of optimally routing and scheduling the collection of medical waste from a disperse group of facilities is recognized as a periodic vehicle routing problem. This study develops a computer system to solve the resulting optimization problem based on a two-phased approach proposed earlier. The first phase solves a standard vehicle routing problem to determine a set of individual routes for the collection vehicles. The second phase uses a mixed integer programming method to assign routes to particular days of the week. The computer system is user-friendly and consists of several Visual Basic programs while the geographical information system is incorporated to facilitate input and output interface and database management. An illustrative example for the infectious waste of 348 hospitals in the Tainan City area demonstrates the effectiveness of the system.     

Organic interference of solidified/stabilized hazardous wastes

Liquid hazardous waste disposal in landfills is usually allowed only after solidification/stabilization. Although various procedures are commonly practiced, little is known about the mechanism(s) of the processes. A particular problem is the interference of organics. Small amounts of organics can interfere with the reaction between inorganic sludges and cementitous matrices. The present communication reports studies of the interaction between selected organic hazardous wastes and Type I Portland cement. Microscopic studies of the structural differences between cements set with water and those set with water plus organic liquids are discussed. In these studies the scanning electron microscope is used to observe samples fractured at 78K. The results provide technical background data on the ultimate stability of critical waste constituents solidified by various binding agents.