The fractionation of extracts of ambient particulate matter for mutagenicity testing

Extracts of air paniculate matter were fractionated by column chromatography over three different adsorbentia. It is shown that chromatography over alumina and over silicagel should be avoided, because of the low recovery of mutagenicity involved. On the other hand, fractionation over XAD-2 is strongly recommended, because of its ease of use and the superior recoveries of both mass and mutagenicity. HPLC subfractionation of the most mutagenic XAD-2 fraction showed that the mutagenicity cannot be attributed to a limited number of compounds.     

Characterisation of particulate matter and gaseous emissions from a large ship diesel engine

Composition of exhaust from a ship diesel engine using heavy fuel oil (HFO) was investigated onboard a large cargo vessel. The emitted particulate matter (PM) properties related to environmental and health impacts were investigated along with composition of the gas-phase emissions. Mass, size distribution, chemical composition and microphysical structure of the PM were investigated. The emission factor for PM was 5.3 g (kg fuel)^?1. The mass size distribution showed a bimodal shape with two maxima: one in the accumulation mode with mean particle diameter D_P around 0.5 μm and one in the coarse mode at D_P around 7 μm. The PM composition was dominated by organic carbon (OC), ash and sulphate while the elemental carbon (EC) composed only a few percent of the total PM. Increase of the PM in exhaust upon cooling was associated with increase of OC and sulphate. Laser analysis of the adsorbed phase in the cooled exhaust showed presence of a rich mixture of polycyclic aromatic hydrocarbon (PAH) species with molecular mass 178–300 amu while PM collected in the hot exhaust showed only four PAH masses.Microstructure and elemental analysis of ship combustion residuals indicate three distinct morphological structures with different chemical composition: soot aggregates, significantly metal polluted; char particles, clean or containing minerals; mineral and/or ash particles. Additionally, organic carbon particles of unburned fuel or/and lubricating oil origin were observed. Hazardous constituents from the combustion of heavy fuel oil such as transitional and alkali earth metals (V, Ni, Ca, Fe) were observed in the PM samples.Measurements of gaseous composition in the exhaust of this particular ship showed emission factors that are on the low side of the interval of global emission factors published in literature for NO_x, hydrocarbons (HC) and CO.     

柴油机排气微粒过滤催化处理技术及进展

介绍了柴油机微粒后处理催化捕集器特点 ,评述了过滤器催化再生方法 ,综述了蜂窝陶瓷载体涂层及催化剂活性组分研究现状。重点阐述了微粒再生催化剂研究进展及其发展趋势     

Study on microstructure and extinction characteristics of particulate matter in diesel engine fueled with different biodiesels

Environmental Science and Pollution Research - Biodiesel combustion particulate matter (PM) is different from diesel combustion PM in terms of microscopic morphology, which directly affects the...     

Photolysis of atrazine in aqueous solution: role of process variables and reactive oxygen species

Photochemical advanced oxidation processes have been considered for the treatment of water and wastewater containing the herbicide atrazine (ATZ), a possible human carcinogen and endocrine disruptor. In this study, we investigated the effects of the photon emission rate and initial concentration on ATZ photolysis at 254 nm, an issue not usually detailed in literature. Moreover, the role of reactive oxygen species (ROS) is discussed. Photon emission rates in the range 0.87?×?10¹⁸–3.6?×?10¹⁸ photons L^?1 s^?1 and [ATZ]₀?=?5 and 20 mg L^?1 were used. The results showed more than 65 % of ATZ removal after 30 min. ATZ photolysis followed apparent first-order kinetics with k values and percent removals decreasing with increasing herbicide initial concentration. A fivefold linear increase in specific degradation rate constants with photon emission rate was observed. Also, regardless the presence of persistent degradation products, toxicity was efficiently removed after 60-min exposure to UV radiation. Experiments confirmed a noticeable contribution of singlet oxygen and radical species to atrazine degradation during photolysis. These results may help understand the behavior of atrazine in different UV-driven photochemical degradation treatment processes.     

Seasonal ambient particulate matter and population health outcomes among communities impacted by road dust in British Columbia,Canada

In recent years, many air quality monitoring programs have favored measurement of particles less than 2.5 µm (PM_2.5) over particles less than 10 µm (PM₁₀) in light of evidence that health impacts are mostly from the fine fraction. However, the coarse fraction (PM_10-2.5) may have independent health impacts that support continued measurement of PM₁₀ in some areas, such as those affected by road dust. The objective of this study was to evaluate the associations between different measures of daily PM exposure and two daily indicators of population health in seven communities in British Columbia, Canada, where road dust is an ongoing concern. The measures of exposure were PM₁₀, PM_2.5, PM_10-2.5, PM_2.5 adjusted for PM_10-2.5, and PM_10-2.5 adjusted for PM_2.5. The indicators of population health were dispensations of the respiratory reliever medication salbutamol sulfate and nonaccidental mortality. This study followed a time-series design using Poisson regression over a 2003–2015 study period, with analyses stratified by three seasons: residential woodsmoke in winter; road dust in spring; and wildfire smoke in summer. A random-effects meta-analysis was conducted to establish a pooled estimate. Overall, an interquartile range increase in daily PM_10-2.5 was associated with a 3.6% [1.6, 5.6] increase in nonaccidental mortality during the road dust season, which was reduced to 3.1% [0.8, 5.4] after adjustment for PM_2.5. The adjusted coarse fraction had no effect on salbutamol dispensations in any season. However, an interquartile range increase in PM_2.5 was associated with a 2.7% [2.0, 3.4] increase in dispensations during the wildfire season. These analyses suggest different impacts of different PM fractions by season, with a robust association between the coarse fraction and nonaccidental mortality in communities and periods affected by road dust. We recommend that PM₁₀ monitoring networks be maintained in these communities to provide feedback for future dust mitigation programs.

Implications: There was a significant association between daily concentrations of the coarse fraction and nonaccidental mortality during the road dust season, even after adjustment for the fine fraction. The acute and chronic health effects associated with exposure to the coarse fraction remain unclear, which supports the maintenance of PM₁₀ monitoring networks to allow for further research in communities affected by sources such as road dust.     

NO2 catalytic formation,consumption, and efflux in various types of diesel particulate filter

Environmental Science and Pollution Research - The high NO2/NOX ratio in the after-treatment system is beneficial to its performance and achieved by NO catalytic conversion in diesel oxidation...     

Concentrations and distributions of carbonaceous species in ambient particles in Kaohsiung City,Taiwan

Concentrations and distributions of elemental carbon (EC) and organic carbon (OC) in particles were measured in Kaohsiung City, Taiwan. PM₁₀ and PM_2.5 samples were collected using a dichotomous sampler from November 1998 to April 1999 and were analyzed for carbonaceous species with an elemental analyzer. The concentrations of carbonaceous species in Kaohsiung City were comparable to those at other urban locations in the world. On average, carbonaceous species accounted for 21.2% of the PM_2.5 and 18.1% of the PM₁₀. It was found that organic carbon dominated the carbonaceous species and was 72.2 and 70.4% of total carbon (TC) for PM_2.5 and PM₁₀. The secondary organic carbon formed through the volatile organic compound gas-to-particle conversion was estimated from the minimum ratio between elemental and organic carbon obtained in this study, and was found to constitute 40.0 and 32.4% of the total organic carbon particle for PM_2.5 and PM₁₀ (or 6.6 and 4.5% of the total particle mass).     

Source apportionment of ambient total suspended particulates and coarse particulate matter in urban areas of Jiaozuo, China

Approximately 750 total suspended particulates (TSPs) and coarse particulate matter (PM10) filter samples from six urban sites and a background site and >210 source samples were collected in Jiaozuo City during January 2002 to April 2003. They were analyzed for mass and abundances of 25 chemical components. Seven contributive sources were identified, and their contributions to ambient TSP/PM10 levels at the seven sites in three seasons (spring, summer, and winter days) and a "whole" year were estimated by a chemical mass balance (CMB) receptor model. The spatial TSP average was high in spring and winter days at a level of approximately 530 microg/m(3) and low in summer days at 456 microg/m(3); however, the spatial PMo0 average exhibited little variation at a level of approximately 325 microg/m(3), and PM10-to-TSP ratios ranged from 0.58 to 0.81, which suggested heavy particulate matter pollution existing in the urban areas. Apportionment results indicated that geological material was the largest contributor to ambient TSP/PM10 concentrations, followed by dust emissions from construction activities, coal combustion, secondary aerosols, vehicle movement, and other industrial sources. In addition, paved road dust and re-entrained dust were also apportioned to the seven source types and found soil, coal combustion, and construction dust to be the major contributors.     

Identification and source apportionment of polycyclic aromatic hydrocarbons in ambient air particulate matter of Riyadh, Saudi Arabia

In an effort to assess the occurrence and sources of polycyclic aromatic hydrocarbons (PAHs) in the ambient air of Riyadh, Saudi Arabia, PM₁₀ samples were collected during December 2010. Diagnostic PAH concentration ratios were used as a tool to identify and characterize the PAH sources. The results reflect high PM₁₀ and PAH concentrations (particulate matter (PM)?=?270–1,270 μg/m³). The corresponding average PAH concentrations were in the range of 18?±?8 to 1,003?±?597 ng/m³ and the total concentrations (total PAHs (TPAHs) of 17 compounds) varied from 1,383 to 13,470 ng/m³ with an average of 5,871?±?2,830 ng/m³. The detection and quantification limits were 1–3 and 1–10 ng/ml, respectively, with a recovery range of 42–80 %. The ratio of the sum of the concentrations of the nine major non-alkylated compounds to the total (CPAHs/TPAHs) was 0.87?±?0.10, and other ratios were determined to apportion the PM sources. The PAHs found are characteristic for emissions from traffic with diesel being a predominant source.     

The effect of thymol and its derivatives on reactions generating reactive oxygen species

The effects of thymol (TOH), thymoquinone (TQ) and dithymoquinone (TQ2) on the reactions generating reactive oxygen species (ROS) such as superoxide anion radical (O2*-), hydroxyl radical (HO*) and singlet oxygen (1O2) were tested using the chemiluminescence (CL) and spectrophotometry methods. All tested compounds acted as scavengers of various ROS. The rate constant of 1O2-dimols quenching by thymol was calculated.     

The assessment of particulate matter emitted from stone-crushing industry by correlating rock textures with particles generated after comminution and dispersed in air environment

The generation and emission of particulate matter from abrasion industry are subjects of the pollution monitoring by multidisciplinary study involving earth sciences and engineering disciplines. This work investigates the correlation between textural properties of in situ rock with class size distribution and morphology of particles generated after rock comminution and particles emitted in the air. A special comminution-dust sampling architecture was realised. The combined use of scanning electron microscopy and particle size analyser was considered in performing digital image analysis on both crushed products and airborne particles collected onto membrane filters. The results show that the size and morphology of crushed particles are linked to the petrographic rock properties. In particular, particles with fibrous morphology are prominent in rocks showing foliated textures where elongated minerals occurred, with implication for asbestos-bearing rocks. For what concerns the airborne particles, the results show that their aerodynamic diameters are independent of the crusher operating conditions. External parameters probably intervene in the distribution of the airborne particles emission, including the dynamic air fluxes, or environmental conditions. By applying mathematical models, the morphology and size range of airborne particles following the comminution processes can be predicted, and results has implication for pollutants contamination due to particulate matters emitted by crush stone industry.     

Enhancement in combustion,performance, and emission characteristics of a diesel engine fueled with diesel,biodiesel, and its blends by using nanoadditive

This article presents the results of investigations carried out to evaluate the improvement in combustion, performance, and emission characteristics of a diesel engine fueled with neat petro-diesel (PD), soybean biodiesel (SB), and 50% SB blended PD (PD50SB) by using carbon nanotube (CNT) as an additive. The acid–alkaline-based transesterification process with sodium hydroxide (NaOH) as a catalyst was applied to derive the methyl ester of SB. A mass fraction of 100 ppm CNT nanoparticle was blended with base fuels by using an ultrasonicator and the physiochemical properties were measured based on EN standards. The measured physiochemical properties are in good agreement with standard limits. The experimental evaluations were carried out under varying brake mean effective pressure (BMEP) conditions in a single-cylinder, four-stroke, and natural aspirated research diesel engine at a constant speed of 1500 rpm. The results reveal that the SB and its blend promote shorter ignition delay period (IDP) that is resulting in lower in-cylinder pressure (ICP) and net heat release rate (NHR) compared to PD. The SB and its blend increase the brake specific fuel consumption (BSFC), and reduce the brake specific energy consumption (BSEC) and exhaust gas temperature (EGT), due to lower heating value, and efficient combustion, respectively. As far as the emission characteristics are concerned, the SB and its blend promote lower magnitude of hydrocarbon (HC), carbon monoxide (CO), carbon dioxide (CO₂), and smoke emissions compared to PD except for oxides of nitrogen (NO_x) emission. The CNT nanoparticle inclusion with base fuels significantly improves the combustion, performance, and emissions level irrespective of engine load conditions.

     

Generation of reactive oxygen species in cyanobacteria and green algae induced by allelochemicals of submerged macrophytes

Inhibition of phytoplankton by allelochemicals released by submerged macrophytes is reported to be one of the mechanisms that maintain a clear-water state in shallow lakes. In order to elucidate this mechanism, the ability of six polyphenols and two long-chain fatty acids to induce the generation of reactive oxygen species (ROS) in phytoplankton was studied using the ROS sensitive probe 2′,7′- dichlorodihydrofluorescein diacetate (DCFH-DA). The results showed that only (+)-catechin (CA) and pyrogallic acid (PA) could induce ROS formation in Microcystis aeruginosa and Pseudokirchneriella subcapitata. 25 mg L⁻¹ CA caused 1.2, 1.4 and 1.8 times increase of ROS levels in M. aeruginosa at 1, 2 and 4 h exposure, respectively, and, correspondingly in P. subcapitata cells, these values were 3.7, 6.2 and 7.7, respectively. PA also significantly increased the levels of intracellular ROS in P. subcapitata (P < 0.01); however, significant ROS generation in M. aeruginosa was observed at only 4 h exposure (P < 0.01). Light enhanced ROS generation in CA treated cells, but not in the cells treated with PA. CA and PA may act as redox cyclers after uptake by test organisms and produce ROS successively. These results suggest that the oxidative stress induced by the redox cycling property of allelochemicals may be one of the important causes for the inhibitory effect of some submerged macrophytes towards undesired phytoplankton in natural aquatic ecosystems.     

Emission profile of 18 carbonyl compounds,CO, CO2, and NOx emitted by a diesel engine fuelled with diesel and ternary blends containing diesel,ethanol and biodiesel or vegetable oils

The impact of vehicular emissions on air depends, among other factors, on the composition of fuel and the technology used to build the engines. The reduction of vehicular emissions requires changes in the fuel composition, and improving the technologies used in the manufacturing of engines and for the after-treatment of gases. In general, improvements to diesel engines have targeted not only emission reductions, but also reductions in fuel consumption. However, changes in the fuel composition have been shown to be a more rapid and effective alternative to reduce pollution. Some factors should been taken into consideration when searching for an alternative fuel to be used in diesel engines, such as emissions, fuel stability, availability and its distribution, as well as its effects on the engine durability. In this work, 45 fuel blends were prepared and their stability was evaluated. The following mixtures (v/v/v) were stable for the 90-day period and were used in the emission study: diesel/ethanol – 90/10%, diesel/ethanol/soybean biodiesel – 80/15/5%, diesel/ethanol/castor biodiesel – 80/15/5%, diesel/ethanol/residual biodiesel – 80/15/5%, diesel/ethanol/soybean oil – 90/7/3%, and diesel/ethanol/castor oil – 90/7/3%. The diesel/ethanol fuel showed higher reduction of NO_x emission at a lower load (2 kW) when compared with pure diesel. The other fuels showed a decrease of NO_x emissions in the ranges of 6.9–75% and 4–85% at 1800 rpm and 2000 rpm, respectively. The combustion efficiencies of the diesel can be enhanced by the addition of the oxygenate fuels, like ethanol and biodiesel/vegetable oil, resulting in a more complete combustion in terms of NO_x emission. In the case of CO₂ the decreases were in the ranges of 5–24% and 4–6% at 1800 rpm and 2000 rpm, respectively. Meanwhile, no differences were observed in CO emission. The carbonyl compounds (CC) studied were formaldehyde, acetaldehyde, propionaldehyde, acrolein, acetone, crotonaldehyde, butyraldehyde, butanone, benzaldehyde, isovaleraldehyde, valeraldehyde, o-toluenaldehyde, m-toluenaldehyde, p-toluenaldehyde, hexaldehyde, octaldehyde, 2,5-dimethylbenzaldehyde, and decaldehyde. Among them, formaldehyde, acetaldehyde, acetone, and propionaldehyde showed the highest emission concentrations. When ternary blend contains vegetable oil, there is a strong tendency to increase the emissions of the high weight CC and decrease the emissions of the low weight CC. The highest concentration of acrolein was observed when the fuel contains diesel, ethanol and biodiesel. With the exception of NO_x, the use of ternary blended fuels resulted on the increase in the emission rates of the studied compounds.     

Analysis of the influencing factors of atmospheric particulate matter accumulation on coniferous species: measurement methods,pollution level,and leaf traits

Environmental Science and Pollution Research - Urban trees, especially their leaves, have the potential to capture atmospheric particulate matter (PM) and improve air quality. However, the amount...     

Leaching of bisphenol A (BPA) to seawater from polycarbonate plastic and its degradation by reactive oxygen species

In this study, (1) change in the concentration of bisphenol A (BPA) leached from polycarbonate (PC) tube to control water (BPA free), seawater and river water at 20 and 37 degrees C as a function of time, (2) the fate of BPA caused by addition of H(2)O(2) and Fe(3+) to seawater containing BPA leached from PC tube were assessed. BPA leached from PC tube to all water samples increased with the ascendant of temperature and with the passage of time. The BPA leaching velocity in seawater was the fastest in three samples (11 ng/day for seawater, 4.8 ng/day for river water 0.8 ng/day for control water at 37 degrees C).BPA leaching velocity from PC tube was significantly high at pH 8 (50 mM Na(2)HPO(4)) and increased dose-dependently. There was no difference in the velocity of BPA among the 50 mM phosphate-buffers at pH 6.5, 7.0 and 7.5. BPA was leached three times higher by addition of Na(+) than K(+). However, the higher the K(+) concentration, the larger the BPA leached from PC tube. Na(+) mixed with PO(4)(-) was effective on BPA leaching from PC tube, but not with SO(4)(-) or Cl(-). The results suggested that BPA leaching from PC tube would be attributed to the concentration of bibasic phosphate such as Na(2)HPO(4) and K(2)HPO(4) in water samples. BPA was degraded in both control water and seawater in the presence of radical oxygen species, but the degradation rate was lower in seawater than in control water, suggesting that anti-oxidative system exists in seawater. Neo-synthesized substance in both control water and seawater in the presence of reactive oxygen species was identified as BPA-quinone by LC-MS.     

Correlations between mutagenic activity of organic extracts of airborne particulate matter, NOx and sulphur dioxide in southern Germany: results of a two-year study

Goals, Scope and Background Among other substances, sulphur dioxide (SO2), nitric oxide (NO) and nitrogen dioxide (NO2) are parameters which are routinely measured to describe basic air quality. Organic extracts of airborne particulate matter contain mutagenic chemical compounds of different origins. The aim of the study was to find correlations between routine monitoring data and mutagenic activity of organic extracts of simultaneously drawn samples.Methods Specimens were collected over a period of two years at 8 sampling sites in south-west Germany. Simultaneously, concentrations of NO, NO2, and SO2 were measured on-line within the framework of the official air monitoring network of Baden-Württemberg, Germany. Dust samples were collected for biotesting using high volume air samplers equipped with glass fibre filters. After sampling was completed, filters were extracted and samples were prepared for biological testing. Mutagenic activity was tested by means of the plate incorporation assay (Ames test) using S. typhimurium TA98 and TA100 tester strains. During the first year of the study, all tests have been performed with and without metabolic activation. Additionally, a series of tests has been performed in parallel with TA98 and TA98NR.Results and Discussion Comparison of Ames test data obtained with and without metabolic activation indicates no statistically significant difference between both methods. Therefore, during the second year of the study, all tests have been performed without metabolic activation. Average yearly activities at the sampling sites were between 1 und 27 Revertants per m³ (Rev/m³). High activities were preferably found at congested sites (Karlsruhe, up to 95 Rev/m³). However, peak values of over 100 Rev/m³ were found in other places where pollution by traffic is significantly lower. The reason for these high level values is not evident. Tests performed using TA98NR tester strain indicate a significant share (average 31%) of compounds requiring activation by nitroreductase for mutagenic activity. Average mutagenic activity can be correlated to routine monitoring parameters. Comparison of averaged data for particular sampling sites indicates significant correlation between nitric oxide and mutagenic activity in TA98 (r²=0.90), while correlation between nitrogen dioxide (0.84) or sulphur dioxide (0.52) and mutagenic activity is weaker. For TA100, correlations are generally weaker than for TA98. Comparison of data for mutagenic activity and routine monitoring data of distant sites being sampled simultaneously shows parallel behaviour.Conclusions Results from this study show that mutagenic activity can be compared to seasonal and local variations of gaseous indicator air pollutants. Tester strain TA98 generally shows the best correlations. Although pollution by particle-bound mutagenic substances is significantly higher during the cold season than during summer on average, mutagenic activity of airborne dust is not a continuous effect. During winter, peak levels as well as low pollution periods can occur. Even during winter time mutagenic activity can reach very low levels typical for summertime. Comparison of results for distant sampling sites where samples have been collected simultaneously indicate that “classical” indicators of air pollution and bacterial mutagenicity of organic extracts from airborne particulate matter are influenced by connected effects. Seasonal trend of mutagenic activity, in particular, is similar to the concentrations of nitrogen oxide. NO is a strong indicator for vehicle exhaust gases. It is concluded that the average mutagenic activity at particular sites can be estimated using NO concentrations as an indicator.     

Degradation of sulfadiazine by UV/Oxone: roles of reactive oxidative species and the formation of disinfection byproducts

Environmental Science and Pollution Research - Sulfadiazine (SDZ) is a typical persistent sulfonamide antibiotic, which has been widely detected in natural drinking water sources. The degradation...     

Degradation of bisphenol-A (BPA) in the presence of reactive oxygen species and its acceleration by lipids and sodium chloride

In this study, (1) change in bisphenol-A (BPA) leached from polycarbonate (PC) tube to water samples at 37 degrees C, (2) effect of reactive oxygen species (ROS) produced by Fenton reaction on BPA recovery and thiobarbituric acid (TBA) value with or without generally existing environmental substances such as alcohol, lipids and NaCl, were investigated. Amounts of BPA leached from PC tube to water samples containing lipids possessing unsaturated fatty acid with high TBA values were significantly lower than the amount of BPA to water only, and addition of NaCl to lipid containing water further decreased BPA concentration. The result indicates that BPA could be degraded by lipoperoxides formed by auto-oxidation of lipid, and NaCl plays an important role in BPA degradation. In the presence of ROS, BPA recovery was the lowest in water and addition of EtOH increased in both BPA recovery and TBA value, suggesting that EtOH could play a role as scavenger of ROS on the oxidative BPA degradation. Furthermore, the higher the concentration of lipid and/or NaCl, the lower the BPA recovery and TBA value. Physiologically and environmentally important concentrations of NaCl could enhance oxidative degradation of BPA in the presence of ROS.