A study of disposed fly ash from landfill to replace Portland cement

The landfills of fly ash are the problem of all power plants because this disposed fly ash is not used in any work. This research studies the potential of using disposed fly ashes which have disposal time of 6-24 months from the landfill of Mae Moh power plants in Thailand to replace Portland cement type I. Median particle sizes of disposed fly ashes between 55.4 and 99.3 microm were ground to reduce the sizes to about 7.1-8.4 microm. Both original and ground disposed fly ashes were investigated on physical and chemical properties. Compressive strengths of disposed fly ash mortars were determined when Portland cement type I was replaced by disposed fly ashes at the rate of 10%, 20%, and 30% by weight of cementitious material (Portland cement type I and disposed fly ash). The results presented that most particles of original disposed fly ashes were solid and sphere with some irregular shape while those of ground disposed fly ashes were solid and irregular shape. CaO and LOI contents of disposed fly ashes with different disposal times had high variation. The compressive strengths of original disposed fly ash mortars were low but those of ground disposed fly ash mortars at the age of 7 days were higher than 75% of the standard mortar and increased to be higher than 100% after 60 days. From the results, it could be concluded that ground disposed fly ashes were excellent pozzolanic materials and could be used as a partial replacement of cement in concrete, even though they were exposed to the weather for 24 months.     

Performance evaluation of cement stabilized fly ash-GBFS mixes as a highway construction material

Fly ash and granulated blast furnace slag (GBFS) are major by-products of thermal and steel plants, respectively. These materials often cause disposal problems and environmental pollution. Detailed laboratory investigations were carried out on cement stabilized fly ash-(GBFS) mixes in order to find out its suitability for road embankments, and for base and sub-base courses of highway pavements. Proctor compaction test, unconfined compressive strength (UCS) test and California Bearing Ratio (CBR) test were conducted on cement stabilized fly ash-GBFS mixes as per the Indian Standard Code of Practice. Cement content in the mix was varied from 0% to 8% at 2% intervals, whereas the slag content was varied as 0%, 10%, 20%, 30% and 40%. Test results show that an increase of either cement or GBFS content in the mixture, results in increase of maximum dry density (MDD) and decrease of optimum moisture content (OMC) of the compacted mixture. The MDD of the cement stabilized fly ash-GBFS mixture is comparably lower than that of similarly graded natural inorganic soil of sand to silt size. This is advantageous in constructing lightweight embankments over soft, compressible soils. An increase in percentage of cement in the fly ash-GBFS mix increases enormously the CBR value. Also an increase of the amount of GBFS in the fly ash sample with fixed cement content improves the CBR value of the stabilized mix. In the present study, the maximum CBR value of compacted fly ash-GBFS-cement (52:40:8) mixture obtained was 105%, indicating its suitability for use in base and sub-base courses in highway pavements with proper combinations of raw materials.     

Soluble salt removal from MSWI fly ash and its stabilization for safer disposal and recovery as road basement material

Fly ash from municipal solid waste incinerators (MSWI) is classified as hazardous in the European Waste Catalogue. Proper stabilization processes should be required before any management option is put into practice. Due to the inorganic nature of MSWI fly ash, cementitious stabilization processes are worthy of consideration. However, the effectiveness of such processes can be severely compromised by the high content of soluble chlorides and sulphates. In this paper, a preliminary washing treatment has been optimized to remove as much as possible soluble salts by employing as little as possible water. Two different operating conditions (single-step and two-step) have been developed to this scope. Furthermore, it has been demonstrated that stabilized systems containing 20% of binder are suitable for safer disposal as well as for material recovery in the field of road basement (cement bound granular material layer). Three commercially available cements (pozzolanic, limestone and slag) have been employed as binders.     

Improvements of nano-SiO2 on sludge/fly ash mortar

Sewage sludge ash has been widely applied to cementitious materials. In this study, in order to determine effects of nano-SiO(2) additives on properties of sludge/fly ash mortar, different amounts of nano-SiO(2) were added to sludge/fly ash mortar specimens to investigate their physical properties and micro-structures. A water-binding ratio of 0.7 was assigned to the mix. Substitution amounts of 0%, 10%, 20%, and 30% of sludge/fly ash (1:1 ratio) were proposed. Moreover, 0%, 1%, 2%, and 3% of nano-SiO(2) was added to the mix. Tests, including SEM and compressive strength, were carried out on mortar specimens cured at 3, 7, and 28 days. Results showed that sludge/fly ash can make the crystals of cement hydration product finer. Moreover, crystals increased after nano-SiO(2) was added. Hence, nano-SiO(2) can improve the effects of sludge/fly ash on the hydration of mortar. Further, due to the low pozzolanic reaction active index of sludge ash, early compressive strengths of sludge/fly ash mortar were decreased. Yet, nano-SiO(2) could help produce hydration crystals, which implies that the addition of nano-SiO(2) to mortar can improve the influence of sludge/fly ash on the development of the early strength of the mortar.     

Properties of alkali-activated systems with stone powder sludge

This article investigates the effects of stone powder sludge on the microstructure and strength development of alkali-activated fly ash and blast furnace slag mixes. Stone powder sludge produced from a crushed aggregate factory was used to replace fly ash and granulated blast furnace slag at replacement ratios of 0%, 10%, 20%, and 30% by mass. The unit weight and compressive strength of the samples were measured, and scanning electron microscopy/energy dispersive spectroscopy and X-ray diffraction (XRD) analyses were performed. The test results indicated that the compressive strength of alkali-activated blast furnace slag mixes using stone powder sludge was higher than that of the alkali-activated blast furnace slag control mix, but the compressive strength of alkali-activated fly ash mixes decreased with increasing replacement ratio of stone powder sludge. Microscopy results indicated that for alkaliactivated blast furnace slag samples, broken surfaces were more evident than for the alkali-activated fly ash samples. For all XRD diagrams, broad and diffuse peaks were observed around 2θ = 35° (d = 2.96–3.03 Å), implying amorphous or short-ordering structure phases.     

Optimization for solidification of low-level-radioactive resin using Taguchi analysis

Solidification of low-level-radioactive (LLW) resin was optimized using Taguchi analytical methodology. The ingredients in LLW mortar which caused the solidification of cement were evaluated through consecutive measurements of the effects of various concentrations of ingredients. Samples selected according to Taguchi's method were separated into 18 different categories and measured at the 7th, 21st, and 28th day after fabrication on developing effects. Evaluations of the various samples focused on whether the compressive and bending strength fulfilled the special criteria of the Taiwan Power Company (TPC). Similar results indicated that both furnace slag and fly ash were the dominant material resulting from the solidification of LLW mortar. The superior combination was obtained as furnace slag 24 wt.%, fly ash 24 wt.%, and cement 8 wt.% to mix 24 wt.% of resin with 20 wt.% of water, to fulfill the contemporary requirements of TPC.     

Possibility of using waste tire rubber and fly ash with Portland cement as construction materials

The growing amount of waste rubber produced from used tires has resulted in an environmental problem. Recycling waste tires has been widely studied for the last 20 years in applications such as asphalt pavement, waterproofing systems and membrane liners. The aim of this study is to evaluate the feasibility of utilizing fly ash and rubber waste with Portland cement as a composite material for masonry applications. Class C fly ash and waste automobile tires in three different sizes were used with Portland cement. Compressive and flexural strength, dry unit weight and water absorption tests were performed on the composite specimens containing waste tire rubber. The compressive strength decreased by increasing the rubber content while increased by increasing the fly ash content for all curing periods. This trend is slightly influenced by particle size. For flexural strength, the specimens with waste tire rubber showed higher values than the control mix probably due to the effect of rubber fibers. The dry unit weight of all specimens decreased with increasing rubber content, which can be explained by the low specific gravity of rubber particles. Water absorption decreased slightly with the increase in rubber particles size. These composite materials containing 10% Portland cement, 70% and 60% fly ash and 20% and 30% tire rubber particles have sufficient strength for masonry applications.     

含砷废渣的固化处理

为了处理有色金属冶炼厂产生的含砷废渣（简称砷渣）,以水泥、粉煤灰、矿渣、黄砂等作为固化材料对砷渣进行了固化研究。确定了砷渣固化的最佳工艺条件：w（砷渣）：50％、w（水泥）=15％、w（粉煤灰）：20％、w（矿渣）=10％、w（黄砂）=5％;砷渣、粉煤灰预先混合球磨10min,加水搅拌后陈化4h,烘干后与水泥、矿渣一起球磨20min,再与水（水与混合物料的质量比为0．175）、添加剂（质量分数为0．05％的添加剂B）及黄砂一起在搅拌机中搅拌6min,然后加压成型,成型后的固化体先放入24℃水泥砼试体养护箱养护14d,然后取出在室温下自然养护14d,养护时间共28d。扫描电子显微镜分析结果显示,砷渣固化体的胶凝状态良好。测试结果表明,砷渣固化体7d抗压强度为8．13MPa,28d抗压强度为14．20 MPa;As的浸出浓度为0．07mg／L,Hg的浸出浓度为0．008mg／L。砷渣固化体的性能达到了国家建材行业标准（JC239-2001《粉煤灰砖》）和危险废物鉴别标准（GB5085．3～1996《危险废物答别标准——浸出毒性答别》）的要求。     

Prediction of unconfined compressive strength of cement paste containing industrial wastes

Neural network analysis was used to construct models of unconfined compressive strength (UCS) as a function of mix composition using existing data from literature studies of Portland cement containing real industrial wastes. The models were able to represent the known non-linear dependency of UCS on curing time and water content, and generalised from the literature data to find relationships between UCS and quantities of five waste types. Substantial decreases in UCS were caused by all wastes; except for EAF dust, the effect was nonlinear with the greatest decrease caused initially by approx. 12% plating sludge, 40% foundry dust, 58% other ash, and 72% MSWI fly ash by mass of dry product. It appears that the maximum waste additions used in modelling may approximate the practical limits of waste additions used in modelling may approximate the practical limits of waste addition to Portland cement, i.e., 50% plating sludge or EAF dust, 64% foundry dust, 92% other ash, and 85% MSWI fly ash by mass of dry product. The laboratory was found to be a key predictive variable and acted as a surrogate for laboratory-specific variables related to cement composition, strength and hardening class, product mixing and preparation details, laboratory conditions, and testing details. While the neural network modelling approach has been shown to be feasible, development of better models would require larger data sets with more complete information regarding laboratory-specific variables and waste composition.     

Utilization of bottom ash from the incineration of separated wastes as a cement substitute.

Waste incineration is still an essential technology in the concept of integrated waste management. Most of the combustion residues are incinerator bottom ash. It has been discovered that incinerator bottom ash from the incineration of separated waste in the primary chamber of the modular two-stage incinerator mainly consists of metal oxides, especially SiO2 and CaO, in proportions that are quite similar to those in cement and so the feasibility of its application as a substitute for cement in concrete was investigated. It was found that after 28 days, the flexural and compressive strengths of the binder using bottom ash were practically comparable with those of a pure cement mixture. The results show that it is reasonable to use a binder containing incinerator bottom ash for applications in which an early-stage lower strength of concrete element is acceptable.     

Utilization of municipal solid waste bottom ash and recycled aggregate in concrete

In the combustion process of municipal solid waste (MSW), bottom ash (BA) represents the major portion of the solid residue. Since BA is composed of oxides, especially SiO(2) and CaO, the feasibility of its application in concrete as a substitute for cement was tested. It was found that at the age of 28 days, the flexural and compressive strengths of the binder linearly decrease at the rate of 0.03 and 0.02 MPa per wt% of BA in the binder, respectively. According to the results it may be recommended to replace up to 15 wt% of cement by BA and to use such binder where a low strength of concrete elements is required. Furthermore, the aggregate used for low strength concrete need not be of a very good quality. Therefore, gravel aggregate was partially replaced by recycled aggregate (RA). Consistency measured by slump was significantly reduced (>50%) when BA or/and RA were introduced into the mixture. However, concrete density and compressive strength were not affected and were approximately 2300 kg/m(3) and approximately 40 MPa, respectively.     

Reuse potential of low-calcium bottom ash as aggregate through pelletization

Coal combustion residues which include fly ash, bottom ash and boiler slag is one of the major pollutants as these residues require large land area for their disposal. Among these residues, utilization of bottom ash in the construction industry is very low. This paper explains the use of bottom ash through pelletization. Raw bottom ash could not be pelletized as such due to its coarseness. Though pulverized bottom ash could be pelletized, the pelletization efficiency was low, and the aggregates were too weak to withstand the handling stresses. To improve the pelletization efficiency, different clay and cementitious binders were used with bottom ash. The influence of different factors and their interaction effects were studied on the duration of pelletization process and the pelletization efficiency through fractional factorial design. Addition of binders facilitated conversion of low-calcium bottom ash into aggregates. To achieve maximum pelletization efficiency, the binder content and moisture requirements vary with type of binder. Addition of Ca(OH)₂ improved the (i) pelletization efficiency, (ii) reduced the duration of pelletization process from an average of 14–7 min, and (iii) reduced the binder dosage for a given pelletization efficiency. For aggregate with clay binders and cementitious binder, Ca(OH)₂ and binder dosage have significant effect in reducing the duration of pelletization process.     

双掺粉煤灰再生骨料对混凝土强度影响研究

通过试验研究再生骨料混凝土中粉煤灰和再生骨料对混凝土强度的影响。采用粉煤灰替代部分水泥、再生骨料替代部分天然粗骨料的方法,通过正交试验测定混凝土立方体抗压强度的方法,来研究粉煤灰对再生骨料混凝土强度的影响。试验得出:当再生骨料掺量为20%~30%时,粉煤灰的最佳掺量为20%左右;当再生骨料掺量高于40%、粉煤灰掺量高于20%时,其混凝土拌合物搅拌时间不小于240 s,且当粉煤灰在20%~30%时,可获得较理想的混凝土抗压强度;当粉煤灰的掺入量分布在20%~30%、再生骨料的最佳掺量为50%时,可获得较理想的混凝土抗压强度。由此得出,合理的再生骨料、粉煤灰掺量对混凝土的抗压强度影响并不明显且有提高的趋势,对降低混凝土成本,提高建筑垃圾的再生利用,有一定的经济效益和社会效益。     

Reuse of thermosetting plastic waste for lightweight concrete

This paper presents the utilization of thermosetting plastic as an admixture in the mix proportion of lightweight concrete. Since this type of plastic cannot be melted in the recycling process, its waste is expected to be more valuable by using as an admixture for the production of non-structural lightweight concrete. Experimental tests for the variation of mix proportion were carried out to determine the suitable proportion to achieve the required properties of lightweight concrete, which are: low dry density and acceptable compressive strength. The mix design in this research is the proportion of plastic, sand, water-cement ratio, aluminum powder, and lignite fly ash. The experimental results show that the plastic not only leads to a low dry density concrete, but also a low strength. It was found that the ratio of cement, sand, fly ash, and plastic equal to 1.0:0.8:0.3:0.9 is an appropriate mix proportion. The results of compressive strength and dry density are 4.14N/mm(2) and 1395kg/m(3), respectively. This type of concrete meets most of the requirements for non-load-bearing lightweight concrete according to ASTM C129 Type II standard.     

Recycling municipal incinerator fly- and scrubber-ash into fused slag for the substantial replacement of cement in cement-mortars

Fly- and scrubber-ash (weight ratio of approximately 1:3) from municipal solid waste incinerators (MSWI) are a major land-fill disposal problem due to their leaching of heavy metals. We uniformly mixed both types of ash with optimal amounts of waste glass frit, which was then melted into a glassy slag. The glassy slag was then pulverized to a particle size smaller than 38 μm for use as a cement substitute (20–40% of total cement) and blended with sand and cement to produce slag-blended cement-mortar (SCM) specimens. The toxicity characteristics of the leaching procedure tests on the pulverized slag samples revealed that the amount of leached heavy metals was far below regulatory thresholds. The compressive strength of the 28-day cured SCM specimens was comparable to that of ordinary Portland cement mortars, while the compressive strength of specimens cured for 60 or 90 days were 3–11% greater. The observed enhanced strength is achieved by Pozzolanic reaction. Preliminary evaluation shows that the combination of MSWI fly- and scrubber-ash with waste glass yields a cost effective and environmentally friendly cement replacement in cement-mortars.     

Leaching of heavy metals from solidified waste using Portland cement and zeolite as a binder

This study investigated the properties of solidified waste using ordinary Portland cement (OPC) containing synthesized zeolite (SZ) and natural zeolite (NZ) as a binder. Natural and synthesized zeolites were used to partially replace the OPC at rates of 0%, 20%, and 40% by weight of the binder. Plating sludge was used as contaminated waste to replace the binder at rates of 40%, 50% and 60% by weight. A water to binder (w/b) ratio of 0.40 was used for all of the mixtures. The setting time and compressive strength of the solidified waste were investigated, while the leachability of the heavy metals was determined by TCLP. Additionally, XRD, XRF, and SEM were performed to investigate the fracture surface, while the pore size distribution was analyzed with MIP. The results indicated that the setting time of the binders marginally increased as the amount of SZ and NZ increased in the mix. The compressive strengths of the pastes containing 20 and 40wt.% of NZ were higher than those containing SZ. The compressive strengths at 28 days of the SZ solidified waste mixes were 1.2-31.1MPa and those of NZ solidified waste mixes were 26.0-62.4MPa as compared to 72.9MPa of the control mix at the same age. The quality of the solidified waste containing zeolites was better than that with OPC alone in terms of the effectiveness in reducing the leachability. The concentrations of heavy metals in the leachates were within the limits specified by the US EPA. SEM and MIP revealed that the replacement of Portland cement by zeolites increased the total porosity but decreased the average pore size and resulted in the better containment of heavy ions from the solidified waste.     

Manufacture of artificial aggregate using MSWI bottom ash

This paper reports the results of an investigation on material recovery by stabilization/solidification of bottom ash coming from a municipal solid waste incineration plant. Stabilization/solidification was carried out to produce artificial aggregate in a rotary plate granulator by adding hydraulic binders based on cement, lime and coal fly ash. Different mixes were tested in which the bottom ash content ranged between 60% and 90%. To avoid undesirable swelling in hardened products, the ash was previously milled and then granulated at room temperature. The granules were tested to assess their suitability to be used as artificial aggregate through the measurement of the following properties: density, water absorption capacity, compressive strength and heavy metals release upon leaching. It was demonstrated that the granules can be classified as lightweight aggregate with mechanical strength strongly dependent on the type of binder. Concrete mixes were prepared with the granulated artificial aggregate and tested for in-service performance, proving to be suitable for the manufacture of standard concrete blocks in all the cases investigated.     

Stabilization of chloro-organics using organophilic bentonite in a cement-blast furnace slag matrix.

The application of cement-based stabilisation/solidification treatment to organic-containing wastes is made difficult by the adverse effect of organics on cement hydration. The use of organophilic clays as pre-solidification adsorbents of the organic compounds can reduce this problem because of the high adsorption power of these clays and their compatibility with the cementitious matrix. This work presents an investigation of the effect on hydration kinetics, physico-mechanical properties and leaching behaviour of cement-based solidified waste forms containing 2-chlorophenol and 1-chloronapthalene adsorbed on organophilic bentonites. These were prepared by cation exchange with benzyldimethyloctadecylammonium chloride and trimethyloctadecylammonium chloride. The binder was a 30% pozzolanic cement, 70% granulated blast furnace slag mixture. Several binder-to-bentonite ratios and different concentrations of the organics on the bentonite were used. Kinetics of hydration were studied by measurement of chemically bound water and by means of thermal and calorimetric analyses. Microstructure and other physico-mechanical properties of the solidified forms were studied by means of mercury intrusion porosimetry, scanning electron microscopy and unconfined compressive strength measurement. Leaching was checked by two different leaching tests: one dynamic, on monolithic samples, and the other static, on powdered samples. This study indicates that the incorporation of the organic-loaded bentonite in the binder matrix causes modifications in the hardened samples by altering cement hydration. The effects of the two organic contaminants are differentiated.     

Recycling MSWI bottom and fly ash as raw materials for Portland cement

Municipal solid waste incineration (MSWI) ash is rich in heavy metals and salts. The disposal of MSWI ash without proper treatment may cause serious environmental problems. Recently, the local cement industry in Taiwan has played an important role in the management of solid wastes because it can utilize various kinds of wastes as either fuels or raw materials. The objective of this study is to assess the possibility of MSWI ash reuse as a raw material for cement production. The ash was first washed with water and acid to remove the chlorides, which could cause serious corrosion in the cement kiln. Various amounts of pre-washed ash were added to replace the clay component of the raw materials for cement production. The allowable limits of chloride in the fly ash and bottom ash were found to be 1.75% and 3.50% respectively. The results indicate that cement production can be a feasible alternative for MSWI ash management. It is also evident that the addition of either fly ash or bottom ash did not have any effect on the compressive strength of the clinker. Cement products conformed to the Chinese National Standard (CNS) of Type II Portland cement with one exception, the setting time of the clinker was much longer.     

Synthetic aggregates from combustion ashes using an innovative rotary kiln

This paper describes the use of a number of different combustion ashes to manufacture synthetic aggregates using an innovative rotary 'Trefoil' kiln. Three types of combustion ash were used, namely: incinerated sewage sludge ash (ISSA); municipal solid waste incinerator bottom ash (MSWIBA-- referred to here as BA); and pulverised fuel ash (Pfa). The fine waste ash fractions listed above were combined with a binder to create a plastic mix that was capable of being formed into 'green pellets'. These pellets were then fired in a Trefoil kiln to sinter the ashes into hard fused aggregates that were then tested for use as a replacement for the natural coarse aggregate in concrete. Results up to 28 days showed that these synthetic aggregates were capable of producing concretes with compressive strengths ranging from 33 to 51 MPa, equivalent to between 73 and 112% of that of the control concrete made with natural aggregates.