The composition, trend and impact of urban solid waste in Beijing

This paper provides an overview of the trend of generation, composition, and management of municipal solid waste, and estimates the carbon emissions arising from municipal solid waste management in Beijing. The correlation analysis conducted shows that the generation of municipal solid waste in Beijing has been growing steadily, showing high correlations (r > 0.9) to the total GDP, per capita income, and the population. Food waste showed an increasing trend since 1990. Compared with the results of an investigation in 1990, ash and woodchips content in 2003 declined from 56% to 17%, while the percentage of paper and plastic increased from 10% to 29% over the same period. The calorific value of the municipal waste also increased, from 2,686 kJ/kg in 1990 to 4,667 kJ/kg in 2003, indicating that the waste is suitable for incineration. Currently, the source separation ratio of municipal waste is approximately 15%. About 94% of all the collected solid waste goes to the landfill while 4% is composted and 2% is incinerated. A moderate garbage collection fee is applied to both permanent and temporary residents in Beijing, but the willingness to pay for solid waste collection and treatment is still low. Under current treatment mode, the total amounts of carbon emission from waste disposal sites and incineration increased with the increase of municipal solid waste, from 29.8 Gg in 1990 to 84.5 Gg in 2003, including 83.3 Gg of CH₄ and 22.0 Gg of CO₂. The data availability and methodological challenges in monitoring the quantity and characteristics of municipal solid waste are discussed.     

Monitoring quantity and characteristics of municipal solid waste in Dhaka City

A reliable estimate of the quantity of solid waste generation in the city is very important for proper solid waste planning and management. However, reported estimates of solid waste generation vary widely and lead to questionability. The reported values have been derived on the assumption of demography, standard rate of waste generation by households, density values, number of trucks engaged for waste transportation and monitoring of truck movement at dump sites, etc. This diverse nature of the available data and the question of accuracy necessitate a rigorous study that has tried to document the waste quantity in the recently formulated master plan of Dhaka City. The socio-economic parameters, behavioral characteristics, generation sources, seasonality, and per capita growth rate are considered in estimating the waste quantity along with its future projections. The findings from the estimation of waste quantities state that seasonal differences in the municipal solid waste stream are not substantial. The most seasonably variable material in the municipal solid waste stream is food waste. Residential waste is relatively homogeneous. Although there are some differences in waste generation depending on demographic and other local factors, most households dispose of essentially similar types of wastes. Variation occurs in waste composition dependent upon income levels and category of sources. Variation also occurs based upon the extent of source reduction and recycling opportunities. As opportunities exist to recycle wastes, the recycling facilities might have to grow at a similar pace to the generation of waste. Physical and chemical characteristics of solid waste are important to implement the waste disposal and management plan for the selection of resource and energy recovery potentials. A number of studies have been conducted to determine the composition of wastes including moisture content and calorific value. The data show that the moisture content in city waste is significantly higher and the calorific value is much lower, which determines the viability of composting or anaerobic digestions rather than waste combustion.     

Measuring waste generation in third world cities: A case study of Ilorin,Nigeria

Problems associated with urban wastes are now at crisis stage in Nigeria. All efforts made to solve the problems have failed, as the efforts were directed towards instant cleaning rather than long lasting programs to cope with problems associated with environmental sanitation. Measurements were taken of the domestic waste generated by randomly selected households in Ilorin, to predict the generation rate for the city. The data was subjected to various analyses. The models used in developed nations were found inappropriate to predict the waste generation rate of the people at Ilorin because of cultural factors. Various methods to cope with the environmental sanitation problems of cities of developing areas were then suggested.     

典型钢铁企业汞排放水平及排放特征研究

以某典型钢铁企业为研究对象,测定企业废气、废水、固废汞排放水平,并分析汞排放特征。研究表明,球团、烧结、高炉工艺废气排口烟尘中汞排放浓度和排放速率明显低于烟气;汞主要以气态形式排放,烧结工艺排口废气汞最高浓度分别是其他2个排口的7倍和3倍。球团、烧结、高炉、电炉四工艺环节中,烧结汞排放速率占四工艺汞排放速率总和的87%。半干法脱硫、氨法脱硫、石灰石石膏脱硫对废气中汞的去除效率分别为90.0%、78.7%和29.9%。企业废水排放未检出汞,脱硫产生固废汞含量明显高于除尘产生固废汞含量,脱硫灰汞含量是脱硫石膏的15倍。     

An off-site snapshot methodology for estimating building construction waste composition - a case study of Hong Kong

Waste composition analysis is essential for implementing appropriate management strategies. In Hong Kong, on-site waste quantification is often not practical due to site space limitation at construction sites. In addition, as the construction waste problem urgently needs addressing, reliable waste generation rates need to be derived over a short time. To address these two issues, this study presents an off-site snapshot methodology for estimating construction waste composition. Three construction sites, at the initial stage, mid-stage, and end stage respectively, are selected for illustrating the proposed snapshot methodology. It is found that the composition of inert and non-inert waste varies significantly at different construction stages. Non-inert waste is an important component of building construction waste, of which wood & timber waste contributes the largest proportion. Following wood & timber waste, metal waste is the second largest source of non-inert waste. Results show that the proposed off-site snapshot methodology can sufficiently solve the problem of limited on-site sorting space and derive reliable detailed waste generation information over a certain short time.     

Waste management modeling by MARKAL model: A case study for Basilicata Region

Air pollution is one of the most pressing environmental problems which affects likewise urban, industrial and rural areas. Environmental planners, regulators and decision makers need reliable, scientifically based tools to find out strategies for controlling air pollution in a cost-effective way, taking into account the whole productive system. In this framework the basic elements of energy-environmental planning have to be extended to include also waste processing technologies amongst the usually considered pollution sources. Bottom-up optimizing models, based on linear programming techniques and customized for specific cases, represent a powerful tool in energy-environmental management. This paper focuses on the integrated modeling of material flows and energy system performed on a local scale case study (Basilicata Region, Southern Italy) using the linear programming model IEA-MARKAL. We have evaluated the feasibility of the model in representing the waste management system to estimate the environmental impact of the waste processing technologies in the context of the whole productive system. A sensitivity analysis has been carried out to emphasize the connections between tariffs, waste disposal technologies assessment and atmospheric emissions. This revised version was published online in July 2006 with corrections to the Cover Date.     

The effects of socioeconomic parameters on household solid-waste generation and composition in developing countries (a case study: Ahvaz,Iran)

Environment problems associated with the generation of waste are part of societal changes where households play an important role. These societal changes influence the size, structure and characteristic of given households. For the effective planning of solid-waste handling infrastructure, it is essential to know the quantity of waste generation and its composition. This paper presents the findings of a study carried out in an urban municipal area in Iran to determine the household solid-waste generation rate and waste composition based on field surveys and to determine the related socioeconomic parameters. The dependent variables were waste generation and composition, and independent variables were family size, family employment, age, number of room and education. Over 400 sample households were selected for the study using a stratified random sampling methodology and from five different socioeconomic groups. Waste collected from all groups of households were segregated and weighted. Waste generation rate was 5.4 kg/household/day. Household solid waste comprised of ten categories of wastes and with the largest component (76.9%). The generation and composition of household solid waste were correlated with family size, education level and households income. This paper adequately suggests new insights concerning the role of socioeconomic parameters in affecting the generation of household waste.     

Lichen transplants as a suitable tool to identify mercury pollution from waste incinerators: a case study from NE Italy

A lichen transplant study aimed at investigating a strong increase in mercury concentrations in lichens was run in a territory of NE Italy where background values were very low only 8 years before. Thalli of the lichen Pseudevernia furfuracea collected in a pristine area were exposed for 1.5, 3 and 6 months at 31 sites selected according to the observed pattern of Hg concentrations, location of the suspected source (a new waste incinerator) and prevailing wind direction. Hg strongly increased at eight sites after 1.5 months, at 12 after 3 months and at 20 after 6 months. The highest values were always located SW and S of the incinerator, in good agreement with the prevailing night wind direction. It was concluded that, although the immediate risk for the population living close to the incinerator is low, long-term hazard due to Hg accumulation in the surrounding environment should be seriously taken into account.     

电子废弃物拆解园区重金属排放特征和周边土壤重金属污染来源解析及风险评价

对某典型电子废弃物拆解园区排放的废气以及周边土壤中的重金属进行监测分析。结果显示,拆解过程中排放的重金属总量由高到低依次为：锡（Sn）、铬（Cr）、镍（Ni）、铅（Pb）、铜（Cu）、锑（Sb）、锰（Mn）、砷（As）、镉（Cd）、汞（Hg）;从处理工艺来看,几个主要拆解工序均有重金属排放,排放量由高到低依次为：加热烤板、火法冶炼、塑料造粒和湿法冶炼工序。园区周边土壤中的Hg、Cd、Cu、Pb平均质量分数超过珠三角土壤污染风险筛选值。相关性和主成分分析结果表明,Pb、Cu、Cd、Ni、Zn等重金属来源于电子废弃物拆解过程,包括废水排放、大气干湿沉降和固体废弃物随意堆放等途径,Cr可能主要来源于成土母质,Hg有电子废弃物之外的其他来源。土壤生态风险评价结果表明,该区域属于很强生态风险,其中Cd和Hg对生态危害的贡献率达到91.6%。土壤环境容量评价结果表明,该区域仅有As和Cr的土壤现存容量较大,Zn和Ni的土壤现存环境容量较小,已达到警戒值,其余重金属均处于超载状态。该地区土壤重金属污染状况须引起足够重视,应尽快制定管控治理措施。     

Multi-level screening of a proposed hazardous waste treatment and disposal facility site--a case study

A comprehensive environmental assessment (EA) is a pre-requisite before the site for developing a hazardous waste treatment and disposal facility (HWTDF) is selected. However, the resource limitations, especially for developing countries, often dictatethat the detailed EA be restricted to those sites, which are constraint free and have low hazard potentials. Thus, a preliminary screening exercise for assessing the suitability ofsite for developing the HWTDF needs to be carried out to avoid huge costs involved in detailed EA. While screening a HWTDF site,various factors such as present land use, ecologically sensitiveareas, geology and hydrogeology of the area, the quality and quantity of wastes, engineered safeguards, and the operationalprocedures that need to be adopted, are required to be addressed. In this paper, a multi-level screening criteria employing RemoteSensing, Constraint Mapping, Groundwater Pollution Potential Index (DRASTIC Index), and the Site Ranking was used to assess the suitability of a proposed site for the development of HWTDF.The study helped to identify various constraints at the proposedsite and their significance on the development of the HWTDF.     

Municipal solid waste generation in growing urban areas in Africa: current practices and relation to socioeconomic factors in Jimma, Ethiopia

As one of cities in the developing countries, a rapid population growth and industrial activities pose many environmental challenges for Jimma city, Ethiopia. One aspect of urban growth posing a threat on sustainable development is poor solid waste management, which results in environmental pollution. The purpose of this study is to evaluate the quantity, composition, sources of waste generated, their current disposal practices, and to recommend appropriate management technologies. The total waste generated daily in Jimma city was ca. 88,000 kg, and the average per capita generation rate was 0.55?±?0.17 kg/capita/day. Eighty-seven percent of the waste was produced by households and 13% by institutions, and a negligible fraction (0.1%) was generated by street sweepings. During the rainy season, 40% more waste was generated than in the dry season because of the increased availability of agricultural food product. Further analysis showed that biodegradable organic waste constitutes 54% by weight with an average moisture content of 60% that falls within the required limits for composting. The nonbiodegradable components constitute 46% of which 30% of it was nonrecyclable material. Only 25% of the community uses municipal containers for disposal at the selected landfill site. Fifty-one percent of the households disposed their waste in individually chosen spots, whereas 22% burned their waste. Finally 2% of households use private waste collectors. The socioeconomic analysis showed that higher family income and educational status is associated more with private or municipal waste collection and less with the application of backyard or open dumping. These insights into generated waste and management practice in Jimma city allow making suggestions for improved collection, treatment, and disposal methods. A primary conclusion is that the biodegradable waste is a major fraction having suitable properties for recycling. As such an economic benefit can be obtained from this waste while avoiding the need for disposal.     

反相高效液相色谱分析空气和废气中己内酰胺的方法研究

研究了反相高效液相色谱分析空气和废气中己内酰胺的方法。该方法以VWD为检测器,检测波长为210nm,流动相为乙腈∶纯水=10∶90,流动相流速为1ml/min。在已选择色谱条件下,连续运行10次,己内酰胺平均出峰时间为4 2min,保留时间和峰面积的相对标准偏差分别为1 5%和3 5%,采样体积为90L时,检测下限为0 01mg/m3,上限为2 20mg/m3,回收率在105 2%-106 3%。     

炉排型城市生活垃圾焚烧炉排气中二

选择四种规模不同的炉排型生活垃圾焚烧炉,分别对其排放烟气中的二     

炉排型城市生活垃圾焚烧炉排气中二(口恶)(口英)污染状况及存在问题

选择四种规模不同的炉排型生活垃圾焚烧炉,分别对其排放烟气中的二(口恶)(口英)进行测定,从不同炉排型垃圾焚烧炉二(口恶)(口英)的排放现状并结合实际调查结果表明,不同炉型的生活垃圾焚烧炉存在一些共性问题,尚需加强垃圾焚烧的炉前、炉中及烟气处理各个环节的运行管理.     

Application of the IPCC Waste Model to solid waste disposal sites in tropical countries: case study of Thailand

Measurements of landfill methane emission were performed at nine solid waste disposal sites in Thailand, including five managed sanitary landfills (four deep and one shallow landfills) and four unmanaged landfills (three deep and one shallow dumpsites). It was found that methane emissions during the rainy season were about five to six times higher than those during the winter and summer seasons in the case of managed landfills and two to five times higher in the case of unmanaged landfills. Methane emission estimate using the Intergovernmental Panel on Climate Change (IPCC) Waste Model was compared with the actual field measurement from the studied disposal sites with methane correction factors and methane oxidation factors that were obtained by error function analysis with default values of half-life parameters. The methane emissions from the first-order decay model from the IPCC Waste Model yielded fair results compared to field measurements. The best fitting values of methane correction factor were 0.65, 0.20, 0.15, and 0.1 for deep landfills, shallow landfills, deep dumpsites, and shallow dumpsites, respectively. Using these key parameters in the case of Thailand, it was estimated that 89.22 Gg of methane were released from solid waste disposal sites into the atmosphere in 2006.     

Denitrification potential of riparian soils in relation to multiscale spatial environmental factors: a case study of a typical watershed,China

The objective of this study was to test the hypothesis that environmental regulators of riparian zone soil denitrification potential differ according to spatial scale within a watershed; consequently, a second objective was to provide spatial strategies for conserving and restoring the purification function of runoff in riparian ecosystems. The results show that soil denitrification in riparian zones was more heterogeneous at the profile scale than at the cross-section and landscape scales. At the profile scale, biogeochemical factors (including soil total organic carbon, total nitrogen, and nitrate–nitrogen) were the major direct regulators of the spatial distribution of soil denitrification enzyme activity (DEA). At the cross-section scale, factors included distance from river bank and vegetation density, while landscape-scale factors, including topographic index, elevation, and land use types, indirectly regulated the spatial distribution of DEA. At the profile scale, soil DEA was greatest in the upper soil layers. At the cross-section scale, maximum soil DEA occurred in the mid-part of the riparian zone. At the landscape scale, soil DEA showed an increasing trend towards downstream sites, except for those in urbanized areas.     

Building consensus on divisive issues: a case study of the Yukon wolf management team

This article presents a case study of a successful effort to reach agreement on one of the most intractable environmental issues of our time: wolf management. This case is unusual in several ways. In this case, the members of the negotiating team were ordinary citizens rather than leaders of organized groups. This team was given an unusually high level of authority to write the plan as they saw fit; the agency pledged to implement “whatever they came up with.” The agency convened the process, but agency personnel were not members of the team and attended only when they were invited. The team members were able to reach agreement on this tough issue even though polar opposites were at the table—one who felt that wolves are a “spiritual essence” and another who felt that, as he put it, “wolves, coyotes, and cockroaches have a lot in common”. They produced a detailed plan that addressed all the issues in just 5 months. Another unusual aspect of this effort is that the final agreement does not list the team members. They explained that they wanted their plan to “stand alone” and be judged based on what it said, not on who was involved.However, just after their agreement was completed, a new, pro-wolf control government was elected that refused to endorse the plan. While the government gave various reasons for not ratifying the plan, more and more diverse interest groups came out in support for both the plan and the process that created it. Eventually, overwhelming public support forced the government to sign and implement the plan as written. This demonstrates that, while it is important for a team to seek the sanction of decision-makers, it is perhaps even more important for the general public to see the effort and the final agreement as fair. Strong support from a broad spectrum of the public can help win the necessary political support.In addition to discussing the unorthodox aspects of this consensus-building effort, this article also attempts to give the reader a front row seat to this process by using the informants' own words—words rich in detail, brimming with color and spoken straight from the heart. Certainly their experience dispels any notion that such efforts are simply a matter of following a recipe. During the process, members of the negotiating team experienced the entire gamut of emotions—anger, defeat, humor and, finally, a genuine sense of pride. As team member Patty Denison put it, “We showed that a random group of people could work together and do something truly monumental.”     

Development of a landfill model to prioritize design and operating objectives

The application of scientifically based decision making tools to help address solid waste management issues dates back to the early 1960s. Researchers continue to use operations research tools to help optimize landfill design and operating parameters. This paper discusses the application of another type of decision making tool, the analytical hierarchy process (AHP), to address priority ranking for a number of landfill engineering design and operating objectives in developing and developed countries. In this application, the AHP is used to rank, and prioritize, economic, environmental, health and safety, legislative and public perception objectives for landfill design and operations specific to landfill distance from a community, and precipitation levels. Results from a global survey using the Delphi process are included, with a discussion on the survey’s impact on the objective rankings relative to community proximity and precipitation. The Delphi process worked extremely well, and was an excellent tool to use in this application. The initial results from the objective rankings show promise in the development of an integrated model for landfill design and operation.