Deodorization of Dimethyl Sulfide Using a Discharge Approach at Room Temperature

Abstract

The traditional technologies for odor removal of thiol usually create either secondary pollution for scrubbing, adsorption, and absorption processes, or sulfur (S) poisoning for catalytic incineration. This study applied a laboratory-scale radio-frequency plasma reactor to destructive percentage-grade concentrations of odorous dimethyl sulfide (CH₃SCH₃, or DMS). Odor was diminished effectively via reforming DMS into mainly carbon disulfide (CS₂) or sulfur dioxide (SO₂). The removal efficiencies of DMS elevated significantly with a lower feeding concentration of DMS or a higher applied rf power. A greater inlet oxygen (O₂)/DMS molar ratio slightly improved the removal efficiency. In an O₂-free environment, DMS was converted primarily to CS₂, methane (CH₄), acetylene (C₂H₂), ethylene (C₂H₄), and hydrogen (H₂), with traces of hydrogen sulfide (H₂S), methyl mercaptan (CH₃SH), and dimethyl disulfide. In an O₂-containing environment, the species detected were SO₂, CS₂, carbonyl sulfide, carbon dioxide (CO₂), CH₄, C₂H₄, C₂H₂, H₂, formal-dehyde, and methanol. Differences in yield of products were functions of the amounts of added O₂ and the applied power. This study provided useful information for gaining insight into the reaction pathways for the DMS dissociation and the formation of products in the plasmolysis and conversion processes.     

Sulfur Toxicity and Media Capacity for H2S Removal in Biofilters Packed with a Natural or a Commercial Granular Medium

Abstract

Two types of media, a natural medium (wood chips) and a commercially engineered medium, were evaluated for sulfur inhibition and capacity for removal of hydrogen sulfide (H₂S). Sulfate was added artificially (40, 65, and 100 mg of S/g of medium) to test its effect on removal efficiency and the media. A humidified gas stream of 50 ppm by volume H₂S was passed through the media-packed columns, and effluent readings for H₂S at the outlet were measured continuously. The overall H₂S baseline removal efficiencies of the column packed with natural medium remained >95% over a 2-day period even with the accumulated sulfur species. Added sulfate at a concentration high enough to saturate the biofilter moisture phase did not appear to affect the H₂S removal process efficiency. The results of additional experiments with a commercial granular medium also demonstrated that the accumulation of amounts of sulfate sufficient enough to saturate the moisture phase of the medium did not have a significant effect on H₂S removal.

When the pH of the biofilter medium was lowered to 4, H₂S removal efficiency did drop to 36%. This work suggests that sulfate mass transfer through the moisture phase to the biofilm phase does not appear to inhibit H₂S removal rates in biofilters. Thus, performance degradation for odor-removing biofilters or H₂S breakthrough in field applications is probably caused by other consequences of high H₂S loading, such as sulfur precipitation.     

The relationship between dimethyl sulfide and particulate sulfate in the mid-atlantic ocean atmosphere

Dimethyl sulfide (DMS) and atmospheric aerosols were sampled simultaneously over the Atlantic Ocean in the vicinity of Bermuda using the NOAA King Air research aircraft. Total and fine (50% cutoff at 2 μm diameter) aerosol fractions were sampled using two independent systems. The average nonsea-salt (nss)SO₄²⁻ concentrations were 1.9 and 1.0 μg m⁻³ (as SO₄²⁻) for the total and the fine fractions in the boundary layer (BL) and 0.53 and 0.27 μg m⁻³ in the free troposphere (FT). Non-sea-salt SO₄²⁻ in the two aerosol fractions were highly correlated (r = 0.90), however a smaller percentage (55%) was found in the fine aerosol near Bermuda relative to that (90%) near the North American continent. The BL SO₄²⁻ concentrations measured in this study were higher than those measured by others at remote marine locations despite the fact that the 7-day air mass back trajectories indicated little or no continental contact at altitudes of 700 mb and below; the trajectories were over subtropical oceanic areas that are expected to be rich in DMS. DMS concentrations were higher near the ocean surface and decreased with increasing altitude within the BL; the average DMS concentration was 0.13 μg m⁻³. Trace levels of DMS were also measured in the FT (0.01 μg m⁻³). Computer simultation of the oxidation and removal of DMS in the marine atmosphere suggests that <50% of the SO₄²⁻ observed could be related to the natural S cycle.     

Monitoring of atmospheric reduced sulfur compounds and their oxidation in two coastal landfill areas

In this study, the distribution characteristics of reduced sulfur compounds (RSCs) in ambient air were investigated in two coastal landfill (LF) facilities and their surrounding areas. The photochemical conversion of RSCs to sulfur dioxide (SO₂) was also evaluated using a photochemical box model (PCBM). Measurements of RSCs were carried out from both in and around areas of two coastal LFs in Gunsan (G) and Donghae (D) city, Korea during several field campaigns (May through December 2004). The dominant RSCs at the Gunsan landfill (G-LF) were found to be DMS and H₂S, whereas those at the Donghae landfill (D-LF) were H₂S and DMDS. The concentrations of DMS at these study sites were likely to be affected not only by LF processes but also by an oceanic source, while such a pattern was more prominent at the D-LF. The chemical species of RSCs that can exert significant influences on the photochemical production of SO₂ in the LF environment were identified to be H₂S, DMS, or DMDS.     

Hydrogen Sulfide Gas Treatment by a Chemical‐Biological Process: Chemical Absorption and Biological Oxidation Steps

In order to remove high concentrations of hydrogen sulfide (H₂S) gas from anaerobic wastewater treatments in livestock farming, a novel process was evaluated for H₂S gas abatement involving the combination of chemical absorption and biological oxidation processes. In this study, the extensive experiments evaluating the removal efficiency, capacity, and removal characteristics of H₂S gas by the chemical absorption reactor were conducted in a continuous operation. In addition, the effects of initial Fe^2 + concentrations, pH, and glucose concentrations on Fe^2 + oxidation by Thiobacillus ferrooxidans CP9 were also examined. The results showed that the chemical process exhibited high removal efficiencies with H₂S concentrations up to 300 ppm, and nearly no acclimation time was required. The limitation of mass‐transfer was verified as the rate‐determining step in the chemical reaction through model validation. The Fe^2 + production rate was clearly affected by the inlet gas concentration as well as flow rate and a prediction equation of ferrous production was established. The optimal operating conditions for the biological oxidation process were below pH 2.3 and 35°C in which more than 90% Fe^3 + formation ratio was achieved. Interestingly, the optimal glucose concentration in the medium was 0.1%, which favored Fe^2 + oxidation and the growth of T. ferrooxidans CP9.     

多层生物滤塔净化硫化氢废气研究

以木屑为填料,采用多层生物滤塔净化H2S气体,研究其适宜的工艺条件及生物降解宏观动力学.结果表明,填料分层可提高H2S去除率,当进气容积负荷＜153.2 g H2S/(m3·d)时,H2S的去除率保持在90%以上;进气浓度低于70 mg/m3,下层200mm填料对H2S总去除率的贡献在50%以上;填料含水率为50%～6...     

Fenton氧化法同时脱硫脱硝的实验研究

应用Fenton液相氧化吸收法进行同时脱硫脱硝实验。首先,利用单因素实验,分别考察了H2O2浓度、Fe2+投加量、初始pH值、UV照射和温度对脱硫脱硝的影响。结果表明,SO2和NO去除率随着H2O2浓度和Fe2+投加量的增大而提高;初始pH对SO2和NO的去除有较大影响;UV能促进SO2和NO的净化;温度对脱硫效率影响不大,但对NO的去除有显著作用,适当升温可以提高脱硝效率。随后,考察了SO2对NO去除率的影响。通过单独脱硝和同时脱硫脱硝的对比实验发现,SO2的加入对NO的去除有一定的促进作用,Fenton法可同时获得起始约80%的脱硝效率和98%以上的脱硫效率。     

高强紫外球形灯光解氧化硫化氢气体

提出了采用可产臭氧的高强球形紫外灯光解氧化硫化氢气体。考察了硫化氢初始浓度、湿度、含氧量、停留时间对硫化氢去除效率的影响。实验结果表明,硫化氢浓度在低浓度范围内,对硫化氢的去除效率可以达到99％以上。反应体系内气体湿度比含氧量对硫化氢的去除效率的影响更明显。气体湿度控制在45％～60％和反应停留时间控制在6～10s范围内为最佳。高强紫外球形灯处理硫化氢过程分别存在直接光解和臭氧氧化作用及两者的协同作用。     

酸碱溶液改性竹基活性炭生物降解H2S

对竹基活性炭采用酸、碱溶液浸渍的方法改性,并用化学和表面形态分析等表征方法测试了其改性前后的特性,研究了不同溶液对改性竹基活性炭在微生物挂膜和滴滤塔去除H2S方面的影响。研究结果表明,用10％NaOH溶液改性后的竹基活性炭较未改性的竹基活性炭碱性基团含量增加了0．614mmol／L,平衡含水率增加了6．08％,碘吸附值增加了29．6mL／g,这些物化性能的改变更有利于生物竹基活性炭去除H2S。对比5种改性方法对生物降解H2S性能的影响,在H2S人口浓度为150～4500mg／m^3、循环液喷淋量0．2L／h、pH6．5—7．5、气体停留时间66s的条件下,经NaOH溶液改性后的竹基活性炭,对H2S的去除率达93．4％以上,效果好于其他改性方法的竹基活性炭。     

Effects of biofilter media depth and moisture content on removal of gases from a swine barn

Media depth (MD) and moisture content (MC) are two important factors that greatly influence biofilter performance. The purpose of this study was to investigate the combined effect of MC and MD on removing ammonia (NH₃), hydrogen sulfide (H₂S), and nitrous oxide (N₂O) from swine barns. Biofiltration performance of different MDs and MCs in combination based on a mixed medium of wood chips and compost was monitored. A 3 × 3 factorial design was adopted, which included three levels of the two factors (MC: 45%, 55%, and 67% [wet basis]; MD: 0.17, 0.33, and 0.50 m). Results indicated that high MC and MD could improve NH₃ removal efficiency, but increase outlet N₂O concentration. When MC was 67%, the average NH₃ removal efficiency of three MDs (0.17, 0.33, and, 0.50 m) ranged from 77.4% to 78.7%; the range of average H₂S removal efficiency dropped from 68.1–90.0% (1–34 days of the test period) to 36.8–63.7% (35–58 days of the test period); and the average outlet N₂O concentration increased by 25.5–60.1%. When MC was 55%, the average removal efficiency of NH₃, H₂S, and N₂O for treatment with 0.33 m MD was 72.8 ± 5.9%, 70.9 ± 13.3%, and –18.9 ± 8.1%, respectively; and the average removal efficiency of NH₃, H₂S, and N₂O for treatment with 0.50 m MD was 77.7 ± 4.2%, 65.8 ± 13.7%, and –24.5 ±12.1%, respectively. When MC was 45%, the highest average NH₃ reduction efficiency among three MDs was 60.7% for 0.5 m MD, and the average N₂O removal efficiency for three MDs ranged from –18.8% to –12.7%. In addition, the pressure drop of 0.33 m MD was significantly lower than that of 0.50 m MD (p < 0.05). To obtain high mitigation of NH₃ and H₂S and avoid elevated emission of N₂O and large pressure drop, 0.33 m MD at 55% MC is recommended.

Implications: The performances of biofilters with three different media depths (0.17, 0.33, and 0.50 m) and three different media moisture contents (45%, 55%, and 67% [wet basis]) were compared to remove gases from a swine barn. Using wood chips and compost mixture as the biofilters media, the combination of 0.33 m media depth and 55% media moisture content is recommended to obtain good reduction of NH₃ and H₂S, and to simultaneously prevent elevated emission of N₂O and large pressure drop across the media.     

辉光放电等离子体氧化降解水中邻苯二甲酸二丁酯

研究了辉光放电等离子体降解水中典型的环境内分泌干扰物邻苯二甲酸二丁酯(DBP)及降解过程中过氧化氢(H2O2)的生成规律。考察了电解质种类、共存污染物(甲醇、叔丁醇)及催化剂等条件对DBP降解及H2O2生成的影响。结果表明,在硫酸钠溶液中DBP降解效率和H2O2生成速率最高;甲醇、叔丁醇等共存污染物对DBP降解和H2O2生成有抑制作用;Fe2+,Fe3+和Cu2+对DBP的降解有催化作用,其催化效果为Fe2+>Fe3+>Cu2+。用高效液相色谱、离子色谱及气质联用仪等仪器分析了降解中间产物,提出了可能的降解机理。     

Gaseous Ammonia Uptake in Compost Biofilters as Related to Compost Water Content

Abstract

Sewage sludge and yard waste compost were used as biofilter materials and tested with respect to their capacity for removing ammonia from air at different water contents. Ammonia removal was measured in biofilters containing compost wetted to different moisture contents ranging from air dry to field capacity (maximum water holding capacity). Filters were operated for 15 days and subsequently analyzed for NH₃/NH₄ ⁺, NO₂ ^-, and NO₃ ^-. The measured nitrogen species concentration profiles inside the filters were used to calculate ammonia removal rates. The results showed that ammonia removal is strongly dependent on the water content in the filter material. At gravimetric water contents below 0.25 g H₂O g solids^-1 for the yard waste compost and 0.5 g H₂O g solids^-1 ammonia removal rates were very low but increased rapidly above these values. The sewage sludge compost filters yielded more than twice the ammonia removal rate observed for yard waste compost likely because of a high initial concentration of nitrifying bacteria originating from the wastewater treatment process and a high air-water interphase surface area that facilitates effective ammonia dissolution and transport to the biofilm.     

Biological elimination of H2S and NH3 from wastegases by biofilter packed with immobilized heterotrophic bacteria

Biotreatment of various ratios of H₂S and NH₃ gas mixtures was studied using the biofilters, packed with co-immobilized cells (Arthrobacter oxydans CH8 for NH₃ and Pseudomonas putida CH11 for H₂S). Extensive tests to determine removal characteristics, removal efficiency, removal kinetics, and pressure drops of the biofilters were performed. To estimate the largest allowable inlet concentration, a prediction model was also employed. Greater than 95% and 90% removal efficiencies were observed for NH₃ and H₂S, respectively, irrespective of the ratios of H₂S and NH₃ gas mixtures. The results showed that H₂S removal of the biofilter was significantly affected by high inlet concentrations of H₂S and NH₃. As high H₂S concentration was an inhibitory substrate for the growth of heterotrophic sulfur-oxidizing bacteria, the activity of H₂S oxidation was thus inhibited. In the case of high NH₃ concentration, the poor H₂S removal efficiency might be attributed to the acidification of the biofilter. The phenomenon was caused by acidic metabolite accumulation of NH₃. Through kinetic analysis, the presence of NH₃ did not hinder the NH₃ removal, but a high H₂S concentration would result in low removal efficiency. Conversely, H₂S of adequate concentrations would favor the removal of incoming NH₃. The results also indicated that maximum inlet concentrations (model-estimated) agreed well with the experimental values for space velocities of 50–150 h⁻¹. Hence, the results would be used as the guideline for the design and operation of biofilters.     

4种高级氧化法处理高浓度正丙醇废水的动力学比较

研究了1%和10%(V/V)模拟正丙醇废水在UV/TiO2体系、UV/H2O2体系、Fe2+/H2O2体系和UV/TiO2/Fe2+/H2O2体系等4种工艺条件下的降解动力学过程,对比了降解动力学特点及工艺参数对动力学常数的影响,优化工艺参数。结果表明,UV/TiO2体系和Fe2+/H2O2体系的降解过程可分为零级反应阶段和一级反应阶段,转折点分别在反应开始后2 h和氧化剂浓度为6.7 g/L,UV/H2O2体系和UV/TiO2/Fe2+/H2O2体系分别符合零级反应和一级反应规律;相同工艺参数条件下,6 h反应后,组合工艺UV/TiO2/Fe2+/H2O2体系在处理效率达85%,比前3个体系分别高52.0%、8.3%和32.0%,与UV/TiO2体系和Fe2+/H2O2体系的处理效率之和持平,其协同效应提高了速率常数,在目标物浓度降低时依然可维持较高降解速率。而目标物浓度提高10倍后,UV能量利用率提高35.5倍,氧化剂用量是Fe2+/H2O2体系的1/7.1。     

Fenton法处理垃圾渗滤液MBR-NF浓缩液

采用Fenton法处理MBR-NF浓缩液,考察了FeSO4·7H2O投加量、n(H2O2)/n(Fe2+)投加比、初始pH对渗滤液MBR-NF浓缩液处理效果的影响,并在最佳实验条件下,探讨浓缩液富里酸(FA)、亲水性有机物(HyI)组分在Fenton氧化前后组成的变化。研究结果表明,在FeSO4·7H2O投加量为0.055 mol/L、n(H2O2)/n(Fe2+)投加比为4、初始pH为7.58时,对COD、腐植酸(UV254)、色度(CN)的去除率分别为79.6%、93.7%和97.8%。Fenton氧化后,浓缩液中有机物组分含量发生了较大变化,腐植酸含量下降,HyI成为渗滤液溶解性有机物主要成分。紫外-可见光谱表明,Fenton法对FA去除效果较好,而对HyI氧化效果较差;傅立叶红外光谱显示,经Fenton氧化后,FA的结构发生了明显变化,而HyI则变化不明显。     

An on-line analysis of reduced sulfur gases in the ambient air surrounding a large industrial complex

In this study, the concentrations of reduced sulfur compounds (RSC: H₂S, CH₃SH, DMS, and DMDS) were continuously measured from an odor monitoring station over a 4-month period (August–November 2005) using an on-line GC system. The hourly measurement data of RSC, collected along with some major aromatic VOCs (benzene, toluene, xylene, etc.), approached the sum of 1500; the mean for all hourly H₂S was computed to be 295 ppt, while those of the others were seen at 7 (DMS), 1 (CH₃SH), and 0.4 ppt (DMDS). When these RSC data were compared across two seasons and on a 24 h scale basis, the values for either the summer or nighttime periods were generally high relative to their counterparts in the fall and daytime. Analysis of these RSC data generally suggests that most RSCs occur at some ppt concentration ranges and that their values frequently fall below detection limits (DL) values (except for H₂S). If the total number of effective data sets (i.e., above DL values) are compared to each other, the results tend to differ significantly between H₂S and the others: the proportion of effective number was as high as 75% for H₂S, while the others were very low (6% of DMS and even less than that for the others). The distributions of RSC were hence clearly distinguished from those of VOCs in that the determination of the latter was scarcely limited by the instrumental detectability. According to the present study, the H₂S data exhibit strong potential as the malodor tracers, while those of the other RSCs are unlikely due to the limited detectability. The overall results of this study hence suggest that several factors which include the selection of target compounds, the location of the monitoring points, and the scale (or number) of total monitoring points should be considered simultaneously to effectively track down the odor occurrence patterns in areas near strong source processes.     

Biofiltration Control of Hydrogen Sulfide 1. Design and Operational Parameters

Laboratory scale biological filter systems for control of hydrogen sulfide (H₂S) in waste gas have been studied and the optimum design and operating parameters determined. Extensive tests have been conducted to evaluate the effect of various filter bed operating parameters such as temperature, retention time, H₂S concentration, and H₂S loading rate. Variable properties of new and used composts such as sulfate content, acidity, and water content have been studied for their influence on H₂S removal efficiency. The effects of compost particle size distribution on system pressure drop and the maximum H₂S elimination capacity were examined. Biofiltration systems containing various types of yard waste compost as the filter material have been observed to remove hydrogen sulfide with efficiencies greater than 99.9 percent for H₂S inlet concentrations in the range from 5 to 2650 ppmv.     

超声-Fenton联用技术深度处理皮革综合废水生化出水

针对皮革综合废水生化处理出水中存在COD和色度偏高等问题,提出采用超声-Fenton联用技术对生化后的皮革综合废水进行深度处理。通过单因素实验考察了超声功率、H2O2投加量、Fe2+投加量(即H2O2/Fe2+比)、溶液pH和反应时间对水样中COD和色度去除率的影响;正交实验结果表明,当溶液初始pH值为4.0时,各因素影响显著性的先后顺序为H2O2>超声功率>反应时间>Fe2+;其优化的实验条件为:H2O2为24.0 mL/L、超声功率为85 W、反应时间为45min、Fe2+为2.2 g/L,经超声-Fenton联用技术深度处理后COD的去除率可达85.4%。在最佳实验条件下,对超声-Fenton联用技术深度处理皮革综合废水生化出水的动力学研究发现,水样中的COD降解反应符合表观一级反应动力学,速率常数增强因子可达8.64,表明存在显著的协同效应。     

酸性洗涤塔-生物滤塔-生物曝气池组合工艺处理恶臭气体NH3和H2S

采用酸性洗涤塔、生物滤塔和生物曝气池的组合工艺处理NH3、H2S恶臭混合气体,研究表明,该组合工艺对NH3和H2S有很好的去除效果,在进气流量为35 L/min,喷淋量45 L/h时,NH3进气浓度50.15~525.4 mg/m3,H2S进气浓度10.23~110.36 mg/m3时,NH3单一进气去除率稳定在99%以上,H2S单一进气去除率90%以上。混合进气后,NH3去除率几乎为100%,H2S的去除率提高至98%以上。在一定的浓度范围内,NH3和H2S之间的相互作用对两者的去除效果没有明显的影响,而且起到了相互促进降解的作用。同时,进气流量和填料层高度都会影响NH3、H2S的去除率。系统对进气容积负荷变化的缓冲能力强,在偶尔超负荷条件下运行并不能使系统崩溃,并且微生物对高负荷逐渐表现出适应性。大部分溶于水的氨由生物曝气池去除,去除率达到96.9%。