Photocatalytic degradation of 5-nitro-1,2,4-triazol-3-one NTO in aqueous suspension of TiO2. Comparison with Fenton oxidation

5-nitro-1,2,4-triazol-3-one (NTO) is a powerful insensitive explosive, present in industrial waste waters. A remediation method based on photochemical decomposition and Fenton oxidation of NTO has been evaluated by monitoring the mineralization of 14C-labelled NTO. The TiO2-catalyzed photodegradation (lambda > 290 nm, TiO2 0.4 g/l, NTO 150 mg/l)) leads to the complete mineralization of NTO in 3 hours. This degradation involves a simultaneous denitrification and ring scission of NTO leading to nitrites, nitrates and carbon dioxide. No significant photo-degradation of NTO was detected in the absence of the catalyst. Long term irradiation over one week, leads to a complete degradation of concentrated NTO (5 g/l), suggesting that this method could be useful to clean-up NTO wastes. Fenton oxidation offers an efficient cost-effective method for NTO remediation. This reaction is faster that the TiO2 catalyzed photolysis and find application on the mineralization of high concentrations of NTO (15 g/l). Fenton oxidation provokes ring cleavage and subsequent elimination of the two carbon atoms of NTO as CO2. During this reaction, the nitro group is completely transformed into nitrates.     

DFT M06-2X investigation of alkaline hydrolysis of nitroaromatic compounds

The nitroaromatic compounds 2,4,6-trinitrotoluene (TNT), 2,4-dinitrotoluene (DNT) and 2,4-dinitroanisole (DNAN) are potential environmental contaminants and their transformations under a variety of environmental conditions are consequently of great interest. One possible method to safely degrade these nitrocompounds is alkaline hydrolysis. A mechanism of the initial stages of this reaction was investigated computationally. Simulations of UV-VIS and NMR spectra for this mechanism were also produced. The results obtained were compared to available experimental data on the alkaline hydrolysis of TNT and suggest that the formation of Meisenheimer complexes and an anion of TNT are potential first-step intermediates in the reaction path. As the reaction proceeds, computational results indicate that polynegative complexes dominate the degradation pathway, followed by cycles of carbon chain opening and breaking. A second possible pathway was identified that leads to polymeric products through Janovsky complex formation. Results from this study indicate that the order of increasing resistance to alkaline hydrolysis is TNT, DNT and DNAN.     

Effective elution of RDX and TNT from particles of Comp B in surface soil

During live fire training exercises, large amounts of explosives are consumed. Low order detonations of high explosive payloads result in the patchy dispersal of particles of high explosive formulations over large areas of firing range soils. Dissolution of explosives from explosive formulation particles into soil pore water is a controlling factor for transport, fate, and effects of explosive compounds. We developed an empirical method to evaluate soils based on functionally defined effective dissolution rates. An automated Accelerated Solvent Extractor was used to determine the effective elution rates under controlled conditions of RDX and TNT from soil columns containing particles of Comp B. Contrived soils containing selected soil geosorbants and reactive surfaces were used to quantitatively determine the importance of these materials. Natural soils from training ranges of various soil types were also evaluated. The effects of geosorbants on effective elution rates were compound- and sorbent-specific. TNT elution was less than that of RDX and was greatly slowed by humic acid. Iron and iron-bearing clays reduced the effective elution rates of both RDX and TNT. This empirical method is a useful tool for directly generating data on the potential for explosives to leach from firing range soils, to identify general bulk soil characteristics that can be used to predict the potential, and to identify means to engineer soil treatments to mitigate potential transport.     

Formulation factors that can reduce the formation of the phytotoxic impurity, N,N'-dibutylurea, from benomyl

Fungicide benomyl is easily decomposed to carbendazim (MBC) and butyl isocyanate (BIC) in formulation, BIC is further hydrolyzed to butylamine. The BIC also reacts with butylamine to form N,N'-dibutylurea (DBU), a phytotoxic compound. The purpose of this study was to investigate the effects of selected additives and the manufacturing method of benomyl water dispersible granules (WG) on reducing DBU content in benomyl formulations. The manufacturing methods studied were granulation by extrusion, fluid bed spray, and spray dry. For the extrusion method, each benomyl powder formulation was homogenized by kneading with 20% v/w of 95% ethanol instead of water. After granulation, the percentages of the active ingredient benomyl and its degradation product carbendazim in each formulation were determined. For the fluid bed spray method, two formulations of wettable powders were formed. The first sample was granulated using 5% Na(2)SO(4) as the binder solution; the second sample used 2% urea. Changes in the active ingredient content after granulation were determined for each sample. For the spray dry method, four basic formulations of 70% benomyl, 5% sodium dodecyl sulfate (SDS) and 10% or 20% sodium sulfate were prepared, to study the effects of HMTA, urea and dispersant on reducing DBU formation in formulation. The DBU content of each formulation was measured for the fresh samples and after 1 year of storage. The results showed that urea had a stabilizing effect on benomyl, and reduced DBU formation. BIC increased benomyl yield during manufacturing, which reduced DBU content in fresh samples but allowed a greater potential for future DBU formation since it did not stabilize the extra benomyl. HMTA was found to reduce DBU in both aqueous BIC and prepared formulations. The study discusses how each of the selected constituents affected DBU formation and how commercial formulations can be improved to reduce DBU formation. From this study, it is clear that a safer benomyl formulation can be developed.     

Analyses of combined effects of cytostatic drugs on micronucleus formation in the <Emphasis Type="Italic">Tradescantia</Emphasis>

Recent experiments showed that 5-fluorouracil (5FU), cisplatin (CDDP), etoposide (ET), and imatinib mesylate (IM), which are currently among the most widely used anticancer drugs, cause damage of the genetic material in higher plants. The aim of the present study was to determine whether mixtures of these drugs cause synergistic or antagonistic effects which may have an impact on their environmental safety. Therefore, the effects of binary mixtures of these anticancer drugs on the induction of micronuclei (MN) which reflect structural and numerical chromosomal aberrations were assessed in Tradescantia tetrads. Synergistic/antagonistic effects were determined by comparison with single exposures that would be equally effective in a reference model of independent action. This comparison was performed at two distinct effect sizes. We found clear evidence for synergisms in combination experiments with IM and antagonism in a high-dose experiment with ET and 5FU. Our findings indicate that IM increases the genotoxic effects of other anticancer drugs. The maximal effects which we found were in the range between 19 and 38 % in the excess of effect sizes predicted under independent action. These effects may have an impact on the overall genotoxic activities of untreated hospital waste waters but not on the environment in general as the predicted environmental concentrations of the studied drugs are several orders of magnitude lower as the levels which are required to cause induction of MN in higher plants.     

Field scale characterization and modeling of contaminant release from a coal tar source zone

A coal tar contaminated site was characterized using traditional and innovative investigation methods. A careful interpretation of hydrogeological and hydrogeochemical data allowed for the conceptualization of the heterogeneous coal tar distribution in the subsurface. Past and future contaminant release from the source zone was calculated using a modeling framework consisting of a three-dimensional steady-state groundwater flow model (MODFLOW) and two hydrogeochemical models (MIN3P). Computational time of long-term simulations was reduced by simplifying the coal tar composition using 3 composite and 2 individual constituents and sequential application of a 2D centerline model (for calibration and predictions) and a 3D model (only for predictions). Predictions were carried out for a period of 1000 years. The results reveal that contaminant mass flux is governed by the geometry of zones containing residual coal tar, amount of coal tar, its composition and the physicochemical properties of the constituents. The long-term predictions made using the 2D model show that even after 1000 years, source depletion will be small with respect to phenanthrene, 89% of initial mass will be still available, and for the moderately and sparingly soluble composite constituents, 60% and 98%, respectively.     

The assessment of the energetic compound 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-Hexaazaisowurtzitane (CL-20) degradability in soil

CL-20 is a relatively new energetic compound with applications in explosive and propellant formulations. Currently, information about the fate of CL-20 in ecological systems is scarce. The aim of this study is to evaluate the biodegradability of CL-20 in soil environments. Four soils were used where initial CL-20 concentrations (above water solubility) ranged from 125 to 1500 mg of CL-20 per kg dry soil (corresponding to the concentrations derived from unexploded ordnance, low order detonation, or manufacturing spills). CL-20 appears to be biodegradable in soil under anaerobic conditions, and additions of organic substrates can substantially accelerate this process. However, CL-20 is not degraded in soil under aerobic conditions kept in the dark at temperatures up to 30 degrees C without organic amendments. Additions of starch or cellulose promote the biodegradation of CL-20 under aerobic conditions. Soil microbial community mediated biodegradation and plant uptake appears to enhance CL-20 biodegradation, the latter suggesting a possible route for CL-20 to entry in the food chain.     

Sequential coupling of bio-augmented permeable reactive barriers for remediation of 1,1,1-trichloroethane contaminated groundwater

Sequential coupling of high-density luffa sponge (HDLS) immobilized microorganism and permeable reactive barriers (IM Bio-PRBs) was superior to intimate coupling of free microorganism and permeable reactive barriers (FM Bio-PRBs) for remediation of 1,1,1-trichloroethane contaminated groundwater. IM Bio-PRBs had much better performance to removal 1,1,1-trichloroethane (1,1,1-TCA) and prevent the transport of 1,1,1-TCA and inorganic ions (NO₃^?, PO₄^3?, and SO₄^2?). The majority of them were prevented and accumulated in upgradient of IM Bio-PRBs. 1,1,1-TCA and inorganic ions in there contributed to the much faster growth of microorganism in upgradient aquifer. Therefore, the removal of 1,1,1-TCA and consumption of inorganic ions in upgradient of Bio-PRBs played a constructive role in reducing the processing load of following zero-valent iron (ZVI) PRBs and the negative effect of free microorganism cells (biological clogging) and inorganic ions (chemical clogging) on Bio-PRB permeability. In addition, IM Bio-PRBs were more conducive to accelerate the removal of 1,1,1-TCA in long-term remediation and 1,1,1-TCA residual concentration significantly lower than the safety standard of 0.2 mg L^?1. The change of terminal by-products of 1,1,1-TCA contaminated groundwater in Bio-PRBs showed that 1,1,1-TCA could be effectively de-chlorinated and mineralized in Bio-PRBs. The reductant H₂S (prolong the service life of ZVI-PRBs) was much more produced and utilized in IM Bio-PRBs. Taken together, sequentially coupled IM Bio-PRBs had a better overall performance, and its service life could be prolonged. It was a different design and idea to update conventional PRB remediation technology and theory.

     

Development of the IM147: an alternative inspection/maintenance mass-emission transient test to address vehicle preconditioning concerns

A series of studies was performed to develop an alternative to the U.S. Environmental Protection Agency's gold standard IM240 mass-based emission test. The new IM147 test was based on the second phase of the IM240 that consists of 147 sec of transient vehicle operation. Paired IM240/IM147 tests were conducted on vehicles ranging from 1981 to 1996 to determine IM147 cutpoints and excess emissions were identified. Additionally, an optimized test procedure was developed that combined possible triplicate IM147s with improved drive trace quality control, fast-pass, and retest methods. The optimized procedure was found to provide improved vehicle preconditioning with a relatively minor decrease in excess emissions identification. Resulting identification rates ranged from 96 to 100% for hydrocarbons (HC), 93-100% for CO, and 93-100% for NOx, depending on cutpoint selection, while false failures caused by lack of vehicle preconditioning were reduced to essentially zero. Significant vehicle throughput improvements were achieved through the development of software algorithms involving modal fast-pass and retest procedures. Modal drive trace variation limits also were developed to improve test accuracy. The combination of the algorithms reduced average IM147 test times by nearly 60%.     

Dissolution kinetics of high explosives particles in a saturated sandy soil

Solid phase high explosive (HE) residues from munitions detonation may be a persistent source of soil and groundwater contamination at military training ranges. Saturated soil column tests were conducted to observe the dissolution behavior of individual components (RDX, HMX, and TNT) from two HE formulations (Comp B and C4). HE particles dissolved readily, with higher velocities yielding higher dissolution rates, higher mass transfer coefficients, and lower effluent concentrations. Effluent concentrations were below solubility limits for all components at superficial velocities of 10-50 cm day(-1). Under continuous flow at 50 cm day(-1), RDX dissolution rates from Comp B and C4 were 34.6 and 97.6 microg h(-1) cm(-2) (based on initial RDX surface area), respectively, significantly lower than previously reported dissolution rates. Cycling between flow and no-flow conditions had a small effect on the dissolution rates and effluent concentrations; however, TNT dissolution from Comp B was enhanced under intermittent-flow conditions. A model that includes advection, dispersion, and film transfer resistance was developed to estimate the steady-state effluent concentrations.     

Sorption and desorption of imidazolium based ionic liquids in different soil types

This study investigates the influence of the two different clay minerals kaolinite and smectite as well as of organic matter on the cation sorption and desorption behaviour of three imidazolium based ionic liquids -1-butyl-3-methyl-imidazolium tetrafluoroborate (IM14 BF(4)), 1-methyl-3-octyl-imidazolium tetrafluoroborate (IM18 BF(4)) and 1-butyl-3-methyl-imidazolium bis[(trifluoromethyl)sulfonyl]imide (IM14 (CF(3)SO(2))(2)N) - in soil. The German standard soil Lufa 2.2 - a natural soil classified as a loamy sand - was the basis substrate for the different soil compositions and also served as a reference soil. The addition of organic matter and clays increases the sorption of the substances and in particular smectite had striking effects on the sorption capacity for all three ionic liquids indicating that ionic interactions play an important role for sorption and desorption processes of ionic liquids in soil. One exception was for kaolinite-containing soils and the IM14 cation: with (CF(3)SO(2))(2)N(-) as an anion the sorption was identical at either 10 wt% or 15 wt% clay content, and with BF(4)(-) sorption was even lower at 15 wt% kaolinite than at 10 wt%. Desorption was weak for IM18 BF(4), presumably owing to the longer alkyl side chain. With regard to the influence of kaolinite on desorption, the same pattern was observed as it was found for the sorption of IM14 BF(4) and IM14 (CF(3)SO(2))(2)N.     

Toxicity of the mixture of selected antineoplastic drugs against aquatic primary producers

The residues of antineoplastic drugs are considered as new and emerging pollutants in aquatic environments. Recent experiments showed relatively high toxicity of 5-fluorouracil (5-FU), imatinib mesylate (IM), etoposide (ET) and cisplatin (CP) that are currently among most widely used antineoplastic drugs, against phytoplankton species. In this study, we investigated the toxic potential of the mixture of 5-FU?+?IM?+?ET against green alga Pseudokirchneriella subcapitata and cyanobacterium Synechococcus leopoliensis, and the stability and sorption of these drugs to algal cells. Toxic potential of the mixture was predicted by the concepts of ‘concentration addition’ and ‘independent action’ and compared to the experimentally determined toxicity. In both test species, the measured toxicity of the mixture was at effects concentrations EC₁₀–EC₅₀ higher than the predicted, whereas at higher effect concentration (EC₉₀), it was lower. In general, P. subcapitata was more sensitive than S. leopoliensis. The stability studies of the tested drugs during the experiment showed that 5-FU, IM and CP are relatively stable, whereas in the cultures exposed to ET, two transformation products with the same mass as ET but different retention time were detected. The measurements of the cell-linked concentrations of the tested compounds after 72 h exposure indicated that except for CP (1.9 % of the initial concentration), these drugs are not adsorbed or absorbed by algal cells. The results of this study showed that in alga and cyanobacteria exposure to the mixture of 5-FU?+?ET?+?IM, in particular at low effect concentration range, caused additive or synergistic effect on growth inhibition, and they suggest that single compound toxicity data are not sufficient for the proper toxicity prediction for aquatic primary producers.     

Short term exposure to elevated trinitrotoluene concentrations induced structural and functional changes in the soil bacterial community

We investigated the acute impact of trinitrotoluene (TNT) contamination of soil on the aerobic bacterial community composition and function. The contamination of the environment with explosive residues presents a serious problem at sites across the world, with the highly toxic compound TNT being the most widespread explosive contaminant. We investigated the acute impact of trinitrotoluene (TNT) contamination of soil on the aerobic bacterial community composition and function. Soil microcosms were amended with a range of concentrations of TNT for 30 days. A polyphasic approach encompassing culture-independent molecular analysis by DGGE, community-level physiological profiling (CLPP) and cell enumeration revealed that the amendment of soils with TNT resulted in a shift from slower growing k-strategists towards faster growing r-strategists. Pseudomonads became prevalent at high concentrations of TNT. Pollution induced community tolerance (PICT) was observed as TNT concentrations increased. Chemical analyses revealed that TNT was reduced to its amino derivatives, products of reductive microbial transformation. The transformation to amino derivatives decreased at high concentrations of TNT, indicative of inhibition of microbial TNT transformation.     

Oxidized starch solutions for environmentally friendly aircraft deicers

Deicers currently used for aircraft deicing, including ethylene glycol and propylene glycol, pose significant threats to surface waters, as a result of high biochemical oxygen demand (BOD) and toxicity to aquatic organisms. Oxidized starch may provide a less toxic deicer with lower BOD. The freezing point depression of starch formulations oxidized using hydrogen peroxide and catalysts (i.e., catalyzed hydrogen peroxide [H2O2] propagations-CHP) was 28 degrees C, and viscosities similar to those of commercial deicers were achieved after post-treatment with granular activated carbon. The most effective oxidized starch formulation exerted a 5-day BOD up to 6 times lower than glycol deicers (103 versus 400 to 800 g O2/L). Toxicity to Ceriodaphnia dubia for this formulation (48-hour lethal concentration, 50% [LC50] of 2.73 g/L) was greater than pure propylene glycol (13.1 g/ L), but lower than propylene glycol deicer formulations (1.02 g/L). Organic acids were identified by gas chromatography/mass spectrometry as the primary constituents in the oxidized starch solution. The proposed deicing system would provide effective deicing while exerting minimal environmental effects (e.g., lower toxicity to aquatic organisms and lower BOD). Furthermore, these deicers could be made from waste starch, promoting sustainability.     

Dissolution and sorption of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) and 2,4,6-trinitrotoluene (TNT) residues from detonated mineral surfaces

Composition B (Comp B) is a commonly used military formulation composed of the toxic explosive compounds 2,4,6-trinitrotoluene (TNT), and hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX). Numerous studies of the temporal fate of explosive compounds in soils, surface water and laboratory batch reactors have been conducted. However, most of these investigations relied on the application of explosive compounds to the media via aqueous addition and thus these studies do not provide information on the real world loading of explosive residues during detonation events. To address this we investigated the dissolution and sorption of TNT and RDX from Comp B residues loaded to pure mineral phases through controlled detonation. Mineral phases included nontronite, vermiculite, biotite and Ottawa sand (quartz with minor calcite). High Performance Liquid Chromatography and Attenuated Total Reflectance Fourier Transform Infrared spectroscopy were used to investigate the dissolution and sorption of TNT and RDX residues loaded onto the mineral surfaces. Detonation resulted in heterogeneous loading of TNT and RDX onto the mineral surfaces. Explosive compound residues dissolved rapidly (within 9 h) in all samples but maximum concentrations for TNT and RDX were not consistent over time due to precipitation from solution, sorption onto mineral surfaces, and/or chemical reactions between explosive compounds and mineral surfaces. We provide a conceptual model of the physical and chemical processes governing the fate of explosive compound residues in soil minerals controlled by sorption-desorption processes.     

Simulating Dissolved Organic Carbon Dynamics at the Swedish Integrated Monitoring Sites with the Integrated Catchments Model for Carbon,INCA-C

Surface water concentrations of dissolved organic carbon ([DOC]) are changing throughout the northern hemisphere due to changes in climate, land use and acid deposition. However, the relative importance of these drivers is unclear. Here, we use the Integrated Catchments model for Carbon (INCA-C) to simulate long-term (1996–2008) streamwater [DOC] at the four Swedish integrated monitoring (IM) sites. These are unmanaged headwater catchments with old-growth forests and no major changes in land use. Daily, seasonal and long-term variations in streamwater [DOC] driven by runoff, seasonal temperature and atmospheric sulfate (SO₄ ²⁻) deposition were observed at all sites. Using INCA-C, it was possible to reproduce observed patterns of variability in streamwater [DOC] at the four IM sites. Runoff was found to be the main short-term control on [DOC]. Seasonal patterns in [DOC] were controlled primarily by soil temperature. Measured SO₄ ²⁻ deposition explained some of the long-term [DOC] variability at all sites.     

Prediction and assessment of ecogenotoxicity of antineoplastic drugs in binary mixtures

The combined genotoxic effects of four anticancer drugs (5-fluorouracil [5-FU], cisplatin [CDDP], etoposide [ET], and imatinib mesylate [IM]) were studied testing their binary mixtures in two crustaceans that are part of the freshwater food chain, namely Daphnia magna and Ceriodaphnia dubia. Genotoxicity was assessed using the in vivo comet assay. Assessment was based on two distinct effect sizes determined from dose-response experiments. Doses for single and combined exposures expected to result in these effect sizes were computed based on Bliss independence as reference model. Statistical comparison by analysis of variance of single and combined toxicities allowed accepting or rejecting the independency hypothesis. The results obtained for D. magna showed independent action for all mixtures except for IM+5-FU that showed an antagonistic interaction. In C. dubia, most mixtures had antagonist interactions except IM+5-FU and IM+CDDP that showed Bliss independence. Despite the antagonistic interactions, our results demonstrated that combinations of anticancer drugs could be of environmental concern because effects occur at very low concentrations that are in the range of concentrations encountered in aquatic systems.     

Influence of selected anti-cancer drugs on the induction of DNA double-strand breaks and changes in gene expression in human hepatoma HepG2 cells

In chemotherapy, various anti-cancer drugs with different mechanisms of action are used and may represent different risk of undesirable delayed side effects in treated patients as well as in occupationally exposed populations. The aim of the present study was to evaluate genotoxic potential of four widely used anti-cancer drugs with different mechanisms of action: 5-fluorouracil (5-FU), cisplatin (CDDP) and etoposide (ET) that cause cell death by targeting DNA function and imatinib mesylate (IM) that inhibits targeted protein kinases in cancer cells in an experimental model with human hepatoma HepG2 cells. After 24 h of exposure all four anti-cancer drugs at non-cytotoxic concentrations induced significant increase in formation of DNA double strand breaks (DSBs), with IM being the least effective. The analysis of the changes in the expression of genes involved in the response to DNA damage (CDKN1A, GADD45A, MDM2), apoptosis (BAX, BCL2) and oncogenesis (MYC, JUN) showed that 5-FU, CDDP and ET upregulated the genes involved in DNA damage response, while the anti-apoptotic gene BCL2 and oncogene MYC were downregulated. On the contrary, IM did not change the mRNA level of the studied genes, showing different mechanism of action that probably does not involve direct interaction with DNA processing. Genotoxic effects of the tested anti-cancer drugs were observed at their therapeutic concentrations that may consequently lead to increased risk for development of delayed adverse effects in patients. In addition, considering the genotoxic mechanism of action of 5-FU, CDDP and ET an increased risk can also not be excluded in occupationally exposed populations. The results also indicate that exposure to 5-FU, CDDP and ET represent a higher risk for delayed effects such as cancer, reproductive effects and heritable disease than exposure to IM.     

Bio-efficacy evaluation of nanoformulations of β-cyfluthrin against Callosobruchus maculatus (Coleoptera: Bruchidae)

In the present investigation, bioefficacy of developed β-cyfluthrin formulations, utilizing laboratory synthesized poly(ethylene glycols) based amphiphilic copolymers, were evaluated against Callosobruchus maculatus (Coleoptera: Bruchidae). The bioefficacy data indicated that the formulations developed by utilizing polymers having PEG - 1500 (3c) and PEG - 2000 (3d) as the hydrophilic segment showed greater efficacy after 14 days as evident from EC(50) values (2.2 and 1.58 mg L(-1) respectively). Also, release from the commercial SC formulation was faster than developed formulations as the commercial formulation had the lowest EC(50) value on the first day (0.51 mg L(-1)). The mean EC(50) of the commercial formulation against C. maculatus was quite high as compared to those of developed formulations. The results suggest that depending upon the polymer matrix used, the application rate of β-cyfluthrin can be optimized to achieve insect control at the desired level and period. The results described in this paper are promising and provide a comparison of developed formulations with the commercial one showing an earlier degradation of β-cyfluthrin in the latter and relatively prolonged activity in the former.